A Brønsted acidic ionic liquid as an efficient and environmentally benign catalyst for biodiesel synthesis from free fatty acids and alcohols

Biodiesel could be synthesized using Brønsted acidic ionic liquid N-methyl-2-pyrrolidonium methyl sulfonate ([NMP][CH₃SO₃]) as a catalyst, specially with free long-chain fatty acids or their mixtures, as well as with low-molecular weight alcohols as substrates. This catalyst showed good catalytic and reusable performance under mild conditions and without any additional organic solvent. The ionic liquid could be reused eight times after the water in the ionic liquid was removed. The yields of fatty acid alkyl esters could reach between 93.6% and 95.3% after the esterifications were carried out at 70 °C for 8 h. Therefore, an efficient and environmentally friendly catalyst was provided for the synthesis of biodiesel from low-cost feedstocks such as waste oils.     

Preparation of solid acid catalyst from glucose-starch mixture for biodiesel production

The aim of this work is to study the catalyst prepared by glucose-starch mixture. Assessment experiments showed that solid acid behaved the highest esterification activity when glucose and corn powder were mixed at ratio of 1:1, carbonized at 400 °C for 75 min and sulfonated with concentrated H₂SO₄ (98%) at 150 °C for 5 h. The catalyst was characterized by acid activity measurement, XPS, TEM and FT-IR. The results indicated that solid acid composed of CS_0.073O_0.541 has both Lewis acid sites and Broˇnsted acid sites caused by SO₃H and COOH. The conversions of oleic acid esterification and triolein transesterification are 96% and 60%, respectively. Catalyst for biodiesel production from waste cottonseed oil containing high free fatty acid (FFA 55.2 wt.%) afforded the methyl ester yield of about 90% after 12 h. The catalyst deactivated gradually after recycles usage, but it could be regenerated by H₂SO₄ treatment.     

Stereoselective synthesis of (R)-1-chloro-3(3,4-difluorophenoxy)-2-propanol using lipases from Pseudomonas aeruginosa in ionic liquid-containing system

Direct transesterification of (R,S)-1-chloro-3-(3,4-difluorophenoxy)-2-propanol (rac-CDPP) (a key intermediate in the synthesis of the chiral drug (S)-lubeluzole) with vinyl butyrate by lipases from Pseudomonas aeruginosa (P. aeruginosa) MTCC 5113 was performed in hexane with ionic liquids (ILs) 1-butyl-3-methyl imidazolium hexafluorophosphate [BMIm][PF₆] and 1-butyl-3-methyl imidazolium tetrafluoroborate [BMIm][BF₄] as co-solvents. The maximum conversion (>49%) and enantiomeric excess (ee > 99.9%) was achieved in 6 h of incubation at 30 °C with [BMIm][PF₆] as co-solvent in a two-phase system. The enzyme was able to perform with the same specificity even at 60 °C in the presence of ILs. It was possible to use lipases repeatedly for more than 10 times while still maintaining absolute enantioselectivity and reactivity. Stability studies on lipases from P. aeruginosa in ILs revealed the fact that the enzyme constancy and the reactivity in catalyzing transesterification of rac-CDPP into (S)-1-chloro-3-(3,4-difluorophenoxy)-2-butanoate was of the order of [BMIm][PF₆] > [BMIm][BF₄] in two-phase system.     

Preparation of cross-linked lipase-coated micro-crystals for biodiesel production from waste cooking oil

A dual modification procedure composed of cross-linking and protein coating with K₂SO₄ was employed to modify Geotrichum sp. lipase for catalyzing biodiesel production from waste cooking oil. Compared to single modification of protein coating with K₂SO₄, the dual modification of cross-linking and lipase coating improved catalytic properties in terms of thermostable stability, organic solvent tolerance, pH stability and operational stability in biodiesel production process, although biodiesel yield and initial reaction rate for CLPCMCs were not improved. After five successive batch reactions, CLPCMCs could still maintain 80% of relative biodiesel yield. CLPCMCs retained 64% of relative biodiesel yield after incubation in a pH range of 4-6 for 4 h, and 85% of relative biodiesel yield after incubation in a range of 45-50 °C for 4 h. CLPCMCs still maintained 83% of relative biodiesel yield after both treated in polar organic solvent and non-polar organic solvent for 4 h.     

Optimization of microwave-assisted FeCl3 pretreatment conditions of rice straw and utilization of Trichoderma viride and Bacillus pumilus for production of reducing sugars

In this study, Box-Behnken design (BBD) and response surface methodology (RSM) were used to optimize microwave-assisted FeCl₃ pretreatment conditions of rice straw with respect to FeCl₃ concentration, microwave intensity, irradiation time and substrate concentration. When rice straw was pretreated at the optimal conditions of FeCl₃ concentration, 0.14 mol/L; microwave intensity, 160 °C; irradiation time, 19 min; substrate concentration, 109 g/L; and inoculated with Trichoderma viride and Bacillus pumilus, the production of reducing sugars was 6.62 g/L. This yield was 2.9 times higher than that obtained with untreated rice straw. The microorganisms degraded 37.8% of pretreated rice straw after 72 h. The structural characteristic analyses suggest that microwave-assisted FeCl₃ pretreatment damaged the silicified waxy surface of rice straw, disrupted almost all the ether linkages between lignin and carbohydrates, and removed lignin.     

Enantioselective acylation of (RS)-phenylethylamine catalysed by lipases

The enzymatic acylation of (RS)-phenylethylamine with different acyl donors catalysed by lipases, was studied in organic solvents with different hydrophobicities and in mixtures with ionic liquids ((ILs); [BMIm][BF₄], [BMIm][SCN], [BMIm][Cl] and [BMIm][PF₆]). Using lipases from Candida antarctica B (CAL-B) and from Aspergillus niger higher conversion degrees and E-values were obtained with ethyl acetate as the acyl donor. When CAL-B was used as the biocatalyst, in a two-phase system formed by [BMIm][X]/dichloromethane or [BMIm][X]/chloroform, the selectivity was better than that obtained in pure organic solvents. The selectivity was found to be related to individual anions in ILs. In this reaction, the ion effectiveness in enhancing the enzyme selectivity followed the series: Cl⁻ > SCN⁻ > BF₄⁻ > PF₆⁻ in mixtures with dichloromethane, and PF₆⁻ > BF₄⁻ > SCN⁻ > Cl⁻ in mixtures with chloroform.     

Alkyl-methylimidazolium ionic liquids affect the growth and fermentative metabolism of Clostridium sp

In this study, the effect of ionic liquids, 1-ethyl-3-methylimidazolium acetate [EMIM][Ac], 1-ethyl-3-methylimidazolium diethylphosphate [EMIM][DEP], and 1-methyl-3-methylimidazolium dimethylphosphate [MMIM][DMP] on the growth and glucose fermentation of Clostridium sp. was investigated. Among the three ionic liquids tested, [MMIM][DMP] was found to be least toxic. Growth of Clostridium sp. was not inhibited up to 2.5, 4 and 4 g L⁻¹ of [EMIM][Ac], [EMIM][DEP] and [MMIM][DMP], respectively. [EMIM][Ac] at <2.5 g L⁻¹, showed hormetic effect and stimulated the growth and fermentation by modulating medium pH. Total organic acid production increased in the presence of 2.5 and 2 g L⁻¹ of [EMIM][Ac] and [MMIM][DMP]. Ionic liquids had no significant influence on alcohol production at <2.5 g L⁻¹. Total gas production was affected by ILs at ?2.5 g L⁻¹ and varied with type of methylimidazolium IL. Overall, the results show that the growth and fermentative metabolism of Clostridium sp. is not impacted by ILs at concentrations below 2.5 g L⁻¹.     

Binding of bivalent ions to actinomycete mannanase is accompanied by conformational change and is a key factor in its thermal stability

The study aimed to define the key factors involved in the modulation of actinomycete mannanases. We focused on the roles of carbohydrate-binding modules (CBMs) and bivalent ions. To investigate the effects of these factors, two actinomycete mannanase genes were cloned from Streptomyces thermoluteus (StManII) and Streptomyces lividans (SlMan). CBMs fused to mannanase catalytic domains do not affect the thermal stability of the proteins. CBM2 of StManII increased the catalytic efficiency toward soluble-mannan and insoluble-mannan by 25%–36%, and CBM10 of SlMan increased the catalytic efficiency toward soluble-mannan by 40%–50%. Thermal stability of wild-type and mutant enzymes was enhanced by calcium and manganese. Thermal stability of SlMandC was also slightly enhanced by magnesium. These results indicated that bivalent ion-binding site responsible for thermal stability was in the catalytic domains. Thermal stability of mannanase differed in the kinds of bivalent ions. Isothermal titration calorimetry revealed that the catalytic domain of StManII bound bivalent ions with a K_a of 5.39 ± 0.45 × 10³–7.56 ± 1.47 × 10³ M^− 1, and the catalytic domain of SlMan bound bivalent ions with a K_a of 1.06 ± 0.34 × 10³–3.86 ± 0.94 × 10³ M^− 1. The stoichiometry of these bindings was consistent with one bivalent ion-binding site per molecule of enzyme. Circular dichroism spectrum revealed that the presence of bivalent ions induced changes in the secondary structures of the enzymes. The binding of certain bivalent ion responsible for thermal stability was accompanied by a different conformational change by each bivalent ion. Actinomycete mannanases belong to GHF5 which contained various hemicellulases; therefore, the information obtained from mannanases applies to the other enzymes.     

Synthesis and magnetic characteristics of new tetrachloroferrates(III) with 2-methylpyridinium, 3-methylpyridinium and 4-methylpyridinium cations: X-ray crystal structure of 4-methylpyridinium tetrachloroferrate(III)

The crystal and molecular structure of a new 4-methylpyridinium tetrachloroferrate(III) of molecular formula [4-Me(Py)H][FeCl₄] was determined. The iron cation is four coordinated by chlorine anions, and it adopts a slightly distorted tetrahedral coordination with two angles smaller, three equal and one larger than tetrahedral one. The compound is isostructural with its 2- and 3-methylpyridinium analogues. Magnetic measurements of the powdered samples gave negative values of the Weiss constants equal −7.3 K, −6.6 K and −6.2 K for [2-Me(Py)H][FeCl₄], [3-Me(Py)H][FeCl₄] and [4-Me(Py)H][FeCl₄], respectively, which suggest antiferromagnetic coupling. The susceptibility curves of all complexes exhibit maxima indicating the presence of antiferromagnetic ordering with a Neel temperature of approximately 7 K.     

Structural and magnetic characteristics of tetramethylammonium tetrahalogenoferrates(III)

A series of tetramethylammonium tetrahalogenoferrates(III), [FeBr_4−nCl_n]⁻ (n = 0, 1, 3, 4), of general formula [(CH₃)₄N][FeBr_4−nCl_n], have been synthesized. The crystal and molecular structures of [(CH₃)₄N][FeCl₄] were determined. The compound is isostructural with its [FeBr_4−nCl_n]⁻ (n = 0, 1, 3, 4) analogues. Magnetic measurements of the powdered samples of [(CH₃)₄N][FeBr_4−nCl_n] gave negative values of the Weiss constant, which suggest antiferromagnetic coupling. The strength of the antiferromagnetic interactions strongly depends on the kind of halide ligands in the coordination sphere of iron(III) and increases with an increasing number of the bromide anions.     

A novel alkaline lipase from Ralstonia with potential application in biodiesel production

With the aim of isolating a biocatalyst able to catalyze biodiesel production from microbial source, Ralstonia sp. CS274 was isolated and a lipase from the strain (RL74) was purified. Molecular weight of RL74 was estimated to be 28,000 Da by SDS-PAGE. The activity was highest at 50-55 °C and pH 8.0-9.5 and was stable at pH 7.0-12.0 and up to 45 °C. It was resistant to oxidizing and reducing agents and the activity was enhanced by detergents. RL74 was 1,3 specific and K_m and V_max for p-nitrophenyl palmitate were 2.73 ± 0.6 mM and 101.4 ± 1.9 mM/min mg, respectively. N-terminal amino acid sequence showed partial homology with that of Penicillium lipases. RL74 produced biodiesel more efficiently in palm oil than in soybean oil; and the production was highest at pH 8.0, at 5% methanol and at 20% water content.     

Penicillium expansum lipase-catalyzed production of biodiesel in ionic liquids

Penicillium expansum lipase (PEL) was used to catalyze biodiesel production from corn oil in [BMIm][PF₆]¹ (an ionic liquid, IL) and tert-butanol. Both systems were optimized in terms of MeOH/oil molar ratio, reaction temperature, enzyme loading, solvent volume, and water content. The high conversion obtained in the IL (86%) as compared to that in tert-butanol (52%) demonstrates that the IL is a superior solvent for PEL-catalyzed biodiesel production. Poor yields were obtained in a series of hydrophilic ILs. Addition of salt hydrates affected biodiesel production predominantly through the specific ion (Hofmeister) effect. The impact of methanol on both activity and stability of PEL in the IL and in hexane was investigated, in comparison to the results obtained by two commonly used lipases, Novozym 435 and Lipozyme TLIM. The results substantiate that while different lipases show different resistance to methanol in different reaction systems, PEL is tolerant to methanol in both systems.     

Catalytic performance of cross-linked enzyme aggregates of Penicillium expansum lipase and their use as catalyst for biodiesel production

Cross-linked enzyme aggregates (CLEAs) of lipase from Penicillium expansum (PEL) were prepared directly from fermentation broth, a more practical and economically viable procedure than the generally used methods that require purified or partially purified enzymes for CLEA preparation. A systematic study of the activity and stability of PEL-CLEAs was undertaken in aqueous solution, organic solvents, and ionic liquids (ILs). Immobilization of the enzyme resulted in a significantly enhanced stability in aqueous solution with regard to pH and temperature. PEL-CLEAs showed an improved activity in the IL [BMIm][PF₆] relative to that observed in hexane, both keeping increased with temperature (up to 90 °C in the IL and 60 °C in hexane). The effect of water content and water activity in these two nonaqueous media showed similar patterns as for the uncrosslinked enzyme. The half life of the CLEAs was higher in hydrophobic organic solvents (hexane and chloroform) than in aqueous solution, and presented a sigmoid relationship with the log P of the organic solvent tested. PEL-CLEAs catalyzed biodiesel production from microalgal oil in the IL [BMIm][PF₆] with a conversion of 85.7%, demonstrating that they can be taken as a promising catalyst for this application.     

Preliminary investigation on the production of fuels and bio-char from Chlamydomonas reinhardtii biomass residue after bio-hydrogen production

The aim of this work was to investigate the potential conversion of Chlamydomonas reinhardtii biomass harvested after hydrogen production. The spent algal biomass was converted into nitrogen-rich bio-char, biodiesel and pyrolysis oil (bio-oil). The yield of lipids (algal oil), obtained by solvent extraction, was 15 ± 2% w/w_dry-biomass. This oil was converted into biodiesel with a 8.7 ± 1% w/w_dry-biomass yield. The extraction residue was pyrolysed in a fixed bed reactor at 350 °C obtaining bio-char as the principal fraction (44 ± 1% w/w_dry-biomass) and 28 ± 2% w/w_dry-biomass of bio-oil. Pyrolysis fractions were characterized by elemental analysis, while the chemical composition of bio-oil was fully characterized by GC-MS, using various derivatization techniques. Energy outputs resulting from this approach were distributed in hydrogen (40%), biodiesel (12%) and pyrolysis fractions (48%), whereas bio-char was the largest fraction in terms of mass.     

Reactions of 6,6-dimethyl-2,2-bipyridyl with iron(II) in aqueous and non-aqueous media

Reaction of anhydrous FeCl₂ with 6,6^′-dimethyl-2,2^′-bipyridyl (dmby) in non-aqueous media gives the yellow, high spin, tetrahedral complex FeCl₂(dmby), which is characterized crystallographically, magnetically and by ¹H NMR spectroscopy. In contrast, reaction of FeCl₂ · 4H₂O with dmby in 0.1 M hydrochloric acid, the method of choice for preparing 3:1 and 2:1 iron(II) complexes of 2,2^′-bipyridyl, gives [H₂dmby][FeCl₄] and [Hdmby][FeCl₄], in which the dmby has been protonated. These complexes are also characterized crystallographically.     

Release of monomeric sugars from Miscanthus sinensis by microwave-assisted ammonia and phosphoric acid treatments

Microwave-assisted ammonium hydroxide (NH₄OH) followed by phosphoric acid (H₃PO₄) treatments were used to release monomeric sugars from Miscanthus sinensis grown in Cha-Chueng-Sao province, Thailand. Treatment with 1.0% (w/v) NH₄OH, 15:1 liquid-to-solid ratio (LSR) at 120 °C temperature for 15 min liberated 2.9 g of monomeric sugars per 100 g of dried biomass, whereas the corresponding yield for a treatment with 1.78% v/v H₃PO₄, 15:1 LSR at 140 °C for 30 min was 62.3 g/100 g. The two-stage pretreatment, treatment with NH₄OH at 120 °C temperature for 15 min followed by treatment with H₃PO₄ at 140 °C for 30 min, impressively provided the highest total monomeric sugar yield of 71.6 g/100 g dried biomass.     

Alumina/silica supported K2CO3 as a catalyst for biodiesel synthesis from sunflower oil

The new type of catalyst for fatty acid methyl esters (FAME or biodiesel) synthesis with K₂CO₃ as active component on alumina/silica support was synthesized using sol–gel method. Corresponding catalyst (xerogel) was prepared by 12 h drying the wet gel in air at 300 °C, 600 °C or 1000 °C at atmospheric pressure. The catalysts activity in the methanolysis of sunflower oil was compared to the activity of the pure K₂CO₃. The effects of various reaction variables on the yield of FAME were investigated. It was found that the temperature of 120 °C and methanol to oil molar ratio of 15:1, are optimal conditions for FAME synthesis with synthesized catalyst. Repeated use of same amount of catalyst indicated that effect of potassium leaching obviously existed leading to decrease of catalyst activity.     

Co (II), Ni(II) and Cu(II) complexes with a new pendant armed macrocyclic ligand showing several π,π-interactions

A new ligand, L, bearing four cyanoethyl pendant groups has been synthesized by reaction of the precursor ligand L¹ with acrylonitrile. The X-ray crystal structure of ligand L reveals the presence of a nanotubular structure in the solid state connected by intermolecular π,π-stacking interactions between adjacent pyridine rings. The coordination capability towards transition metal ions [Co(II), Ni(II) and Cu(II)] has been investigated starting from the hydrated nitrate and perchlorate salts of the metals. The new ligand L and the metal complexes obtained were characterized by elemental analysis, FAB MS, conductivity measurements, magnetic studies, IR and UV-vis spectroscopy. Furthermore, the crystal structure of ligand L and of the complexes [CoL][Co(NO₃)₄] · CH₃CN (1), [NiL](NO₃)₂ (3), [NiL](ClO₄)₂ · CH₃CN · 3H₂O (4), [CuL][Cu(NO₃)₃(H₂O)₂](NO₃) · H₂O (5) and [CuL](ClO₄)₂ · 2CH₃CN (6) were determined. The nitrate ions in the complexes are located near the pyridine rings and π,π-stacking interactions between pyridine rings, nitrate ions and nitrile groups have been found.     

Reactions and structures in the gallium(III)/indium(III)-N,N-dimethylthioformamide systems

The structure of the N,N-dimethylthioformamide (DMTF) solvated gallium(III) ion has been determined in solution by means of extended X-ray absorption fine structure (EXAFS) spectroscopy. The gallium(III) ion is four-coordinate in tetrahedral fashion with a mean Ga-S bond distance of 2.233(2) Å in DMTF solution. At the dissolution of indium(III) perchlorate or trifluoromethanesulfonate in DMTF coordinated solvent molecules are partly reduced to sulfide ions, and a tetrameric complex with the composition [In₄S₄(SHN(CH₃)₂)₁₂]⁴⁺ is formed. The structure of the solid tetrameric complex in the perchlorate salt was solved with single crystal X-ray diffraction. Four indium(III) ions and four sulfide ions form a highly symmetric heterocubane structure where each indium binds three bridging sulfide ions and each sulfide ion binds three indium(III) ions with a mean In-S bond distance of 2.584(1) Å, and S-In-S angles of 90.3(1)°. Each indium(III) additionally binds three DMTF molecules at significantly longer mean In-S bond distance, 2.703(1) Å; the S-In-S angles are in the range 80.3-90.4°. Large angle X-ray scattering data on a DMTF solution of indium(III) trifluoromethanesulfonate show that the same tetrameric species characterized in the solid state is also present in solution, whereas the EXAFS measurements only give information about the In-S bond distances due to the short core hole lifetime.     

Preliminary studies on cryopreservation of snakehead (Channa striata) embryos

This paper reports the findings of the ongoing studies on cryopreservation of the snakehead, Channa striata embryos. The specific objective of this study was to collect data on the sensitivity of C. striata embryo hatching rate to low temperatures at two different developmental stages in the presence of four different cryoprotectants. Embryos at morula and heartbeat stages were selected and incubated in 1 M dimethyl sulfoxide (Me₂SO), 1 M ethylene glycol (EG), 1 M methanol (MeOH) and 0.1 M sucrose solutions at different temperatures for a period of time. Embryos were kept at 24 °C (control), 15 °C, 4 °C and −2 °C for 5 min, 1 h and 3 h. Following these treatments, the embryos were then transferred into a 24 °C water bath until hatch to evaluate the hatching rate. The results showed that there was a significant decrease of hatching rate in both developmental stages following exposure to 4 °C and −2 °C at 1 h and 3 h exposure in each treatment. Heartbeat stage was more tolerant against chilling at −2 °C for 3 h exposure in Me₂SO followed by MeOH, sucrose and EG. Further studies will be conducted to find the best method to preserve embryos for long term storage.