The “Midas Touch” Transformation of TiO2 Nanowire Arrays during Visible Light Photoelectrochemical Performance by Carbon/Nitrogen Coimplantation

Titanium dioxide is a promising photoanode material for water oxidation, but it is substantially limited by its poor efficiency in the visible light range. Herein, an innovative carbon/nitrogen coimplantation method is utilized to realize the “Midas touch” transformation of TiO₂ nanowire (NW) arrays for photoelectrochemical (PEC) water splitting in visible light. These modified golden–yellow rutile TiO₂ NW arrays (C/N‐TiO₂) exhibit remarkably enhanced absorption in visible light regions and more efficient charge separation and transfer. As a result, the photocurrent density of carbon/nitrogen co‐implanted TiO₂ under visible light (>420 nm) can reach 0.76 mA cm^?2, which far exceeds the value of 3 µA cm^?2 seen for pristine TiO₂ nanowire arrays at 0.8 V versus Ag/AgCl. An incident photon to electron conversion efficiency of ≈14.8% is achieved at 450 nm on C/N‐TiO₂ without any other cocatalysts. The ion implantation doping approach, combined with codoping strategies, is proved to be an effective strategy for enhancing the photoelectrochemical conversion and can enable further improvement of the PEC water‐splitting performance of many other semiconductor photoelectrodes.     

Overcoming Charge Collection Limitation at Solid/Liquid Interface by a Controllable Crystal Deficient Overlayer

Bulk and surface charge recombination of photoelectrode are two key processes that significantly hinder solar‐to‐fuel conversion of photoelectrochemical cell (PEC). In this study, the function of a “crystal‐deficient” overlayer is unveiled, which outperforms a traditionally used amorphous or crystalline overlayer in PEC water splitting by exhibiting a high conductivity and large electron diffusion length to enable unlimited electron collection. The optimized ≈2.5 nm thickness of the “crystal‐deficient” shell results in a depletion layer with a width of 3 nm, which overcomes the flat band limitation of the photovoltage and increases the light absorptivity in the wavelength range from 300 to 420 nm. In addition, a 50‐fold increase in the conductivity yields a one‐order‐of‐magnitude increase in the diffusion length of an electron (L_n )(≈20 μm), allowing for unlimited electron collection in the 1.9 μm TiO₂ nanowire array with the “crystal‐deficient” shell. The controllable “crystal‐deficient” overlayer in rutile TiO₂ nanowires photoanode achieves a photocurrent density greater than 2.0 mA cm^?2 at 1.23 V versus reversible hydrogen electrode (RHE), a 1.18% applied bias photon‐to‐current efficiency at 0.49 V versus RHE, a faradaic efficiency greater than 93.5% at 0.6 V versus Pt under air mass 1.5G simulated solar light illumination (100 mW cm^?2).     

Multifunctional Coatings from Scalable Single Source Precursor Chemistry in Tandem Photoelectrochemical Water Splitting

The straightforward and inexpensive fabrication of stabilized and activated photoelectrodes for application to tandem photoelectrochemical (PEC) water splitting is reported. Semiconductors such as Si, WO₃, and BiVO₄ can be coated with a composite layer formed upon hydrolytic decomposition of hetero­bimetallic single source precursors (SSPs) based on Ti and Ni, or Ti and Co in a simple single‐step process under ambient conditions. The resulting 3d‐transition metal oxide composite films are multifunctional, as they protect the semiconductor electrode from corrosion with an amorphous TiO₂ coating and act as bifunctional electrocatalysts for H₂ and O₂ evolution based on catalytic Ni or Co species. Thus, this approach enables the use of the same precursors for both photoelectrodes in tandem PEC water splitting, and SSP chemistry is thereby established as a highly versatile low‐cost approach to protect and activate photoelectrodes. In an optimized system, SSP coating of a Si photocathode and a BiVO₄ photoanode resulted in a benchmark noble metal‐free dual‐photoelectrode tandem PEC cell for overall solar water splitting with an applied bias solar‐to‐hydrogen conversion efficiency of 0.59% and a half‐life photostability of 5 h.     

Constructing a AZO/TiO2 Core/Shell Nanocone Array with Uniformly Dispersed Au NPs for Enhancing Photoelectrochemical Water Splitting

Constructing core/shell nanostructures with optimal structure and composition could maximize the solar light utilization. Here, using an Al nanocone array as a substrate, a well‐defined regular array of AZO/TiO₂ core/shell nanocones with uniformly dispersed Au nanoparticles (AZO/TiO₂/Au NCA) is successfully realized through three sequential steps of atomic layer deposition, physical vapor deposition, and annealing processes. By tuning the structural and compositional parameters, the advantages of light trapping and short carrier diffusion from the core/shell nanocone array, as well as the surface plasmon resonance and catalytic effects from the Au nanoparticles can be maximally utilized. Accordingly, a remarkable photoelectrochemical (PEC) performance can be acquired and the photocurrent density of the AZO/TiO₂/Au NCA electrode reaches up to 1.1 mA cm^?2 at 1.23 V, versus reversible hydrogen electrode (RHE) under simulated sunlight illumination, which is five times that of a flat AZO/TiO₂ electrode (0.22 mA cm^?2). Moreover, the photoconversion of the AZO/TiO₂/Au NCA electrode approaches 0.73% at 0.21 V versus RHE, which is one of the highest values with the lowest applied bias ever reported in Au/TiO₂ PEC composites. These results demonstrate a feasible route toward the scalable fabrication of well‐modulated core/shell nanostructures and can be easily applied to other metal/semiconductor composites for high‐performance PEC.     

Scalable Triple Cation Mixed Halide Perovskite–BiVO4 Tandems for Bias‐Free Water Splitting

Strong interest exists in the development of organic–inorganic lead halide perovskite photovoltaics and of photoelectrochemical (PEC) tandem absorber systems for solar fuel production. However, their scalability and durability have long been limiting factors. In this work, it is revealed how both fields can be seamlessly merged together, to obtain scalable, bias‐free solar water splitting tandem devices. For this purpose, state‐of‐the‐art cesium formamidinium methylammonium (CsFAMA) triple cation mixed halide perovskite photovoltaic cells with a nickel oxide (NiO_x) hole transport layer are employed to produce Field's metal‐epoxy encapsulated photocathodes. Their stability (up to 7 h), photocurrent density (–12.1 ± 0.3 mA cm^?2 at 0 V versus reversible hydrogen electrode, RHE), and reproducibility enable a matching combination with robust BiVO₄ photoanodes, resulting in 0.25 cm² PEC tandems with an excellent stability of up to 20 h and a bias‐free solar‐to‐hydrogen efficiency of 0.35 ± 0.14%. The high reliability of the fabrication procedures allows scaling of the devices up to 10 cm², with a slight decrease in bias‐free photocurrent density from 0.39 ± 0.15 to 0.23 ± 0.10 mA cm^?2 due to an increasing series resistance. To characterize these devices, a versatile 3D‐printed PEC cell is also developed.     

Few‐Layer MoS2 Flakes as Active Buffer Layer for Stable Perovskite Solar Cells

Solution‐processed few‐layer MoS₂ flakes are exploited as an active buffer layer in hybrid lead–halide perovskite solar cells (PSCs). Glass/FTO/compact‐TiO₂/mesoporous‐TiO₂/CH₃NH₃PbI₃/MoS₂/Spiro‐OMeTAD/Au solar cells are realized with the MoS₂ flakes having a twofold function, acting both as a protective layer, by preventing the formation of shunt contacts between the perovskite and the Au electrode, and as a hole transport layer from the perovskite to the Spiro‐OMeTAD. As prepared PSC demonstrates a power conversion efficiency (η) of 13.3%, along with a higher lifetime stability over 550 h with respect to reference PSC without MoS₂ (Δη/η = ?7% vs. Δη/η = ?34%). Large‐area PSCs (1.05 cm² active area) are also fabricated to demonstrate the scalability of this approach, achieving η of 11.5%. Our results pave the way toward the implementation of MoS₂ as a material able to boost the shelf life of large‐area perovskite solar cells in view of their commercialization.     

Novel Black BiVO4/TiO2−x Photoanode with Enhanced Photon Absorption and Charge Separation for Efficient and Stable Solar Water Splitting

Recent advances in solar water splitting by using BiVO₄ as a photoanode have greatly optimized charge carrier and reaction dynamics, but relatively wide bandgap and poor photostability are still bottlenecks. Here, an excellent photoanode of black BiVO₄@amorphous TiO_2?x to tackle both problems is reported. Its applied bias photon‐to‐current efficiency for solar water splitting is up to 2.5%, which is a new record for a single oxide photon absorber. This unique core–shell structure is fabricated by coating amorphous TiO₂ on nanoporous BiVO₄ with the aid of atomic layer deposition and further hydrogen plasma treatment at room temperature. The black BiVO₄ with moderate oxygen vacancies reveals a bandgap reduction of ≈0.3 eV and significantly enhances solar utilization, charge transport and separation simultaneously, compared with conventional BiVO₄. The amorphous layer of TiO_2?x acts as both oxygen‐evolution catalyst and protection layer, which suppresses anodic photocorrosion to stabilize black BiVO₄. This configuration of black BiVO₄@amorphous TiO_2?x may provide an effective strategy to prompt solar water splitting toward practical applications.     

Fullerene as a Photoelectron Transfer Promoter Enabling Stable TiO2‐Protected Sb2Se3 Photocathodes for Photo‐Electrochemical Water Splitting

Understanding the degradation mechanisms of photoelectrodes and improving their stability are essential for fully realizing solar‐to‐hydrogen conversion via photo‐electrochemical (PEC) devices. Although amorphous TiO₂ layers have been widely employed as a protective layer on top of p‐type semiconductors to implement durable photocathodes, gradual photocurrent degradation is still unavoidable. This study elucidates the photocurrent degradation mechanisms of TiO₂‐protected Sb₂Se₃ photocathodes and proposes a novel interface‐modification methodology in which fullerene (C₆₀) is introduced as a photoelectron transfer promoter for significantly enhancing long‐term stability. It is demonstrated that the accumulation of photogenerated electrons at the surface of the TiO₂ layer induces the reductive dissolution of TiO₂, accompanied by photocurrent degradation. In addition, the insertion of the C₆₀ photoelectron transfer promoter at the Pt/TiO₂ interface facilitates the rapid transfer of photogenerated electrons out of the TiO₂ layer, thereby yielding enhanced stability. The Pt/C₆₀/TiO₂/Sb₂Se₃ device exhibits a high photocurrent density of 17 mA cm^?2 and outstanding stability over 10 h of operation, representing the best PEC performance and long‐term stability compared with previously reported Sb₂Se₃‐based photocathodes. This research not only provides in‐depth understanding of the degradation mechanisms of TiO₂‐protected photocathodes, but also suggests a new direction to achieve durable photocathodes for photo‐electrochemical water splitting.     

3D Porous Pyramid Heterostructure Array Realizing Efficient Photo‐Electrochemical Performance

Direct photo‐electrochemical (PEC) water splitting is of great practical interest for developing a sustainable energy systems, but remains a big challenge owing to sluggish charge separation, low efficiency, and poor stability. Herein, a 3D porous In₂O₃/In₂S₃ pyramid heterostructure array on a fluorine‐doped tin oxide substrate is fabricated by an ion exchange–induced synthesis strategy. Based on the synergistic structural and electronic modulations from density functional theory calculations and experimental observations, 3D porous In₂O₃/In₂S₃ photoanode by the protective layer delivers a low onset potential of ≈0.02 V versus reversible hydrogen electrode (RHE), the highest photocurrent density of 8.2 mA cm^?2 at 1.23 V versus RHE among all the In₂S₃ photoanodes reported to date, an incident photon‐to‐current efficiency of 76% at 400 nm, and high stability over 20 h for PEC water splitting are reported. This work provides an alternative promising prototype for the design and construction of novel heterostructures in robust PEC water splitting applications.     

Boosting Photoelectrochemical Water Splitting by TENG‐Charged Li‐Ion Battery

The need for cost‐effective and sustainable power supplies has spurred a growing interest in hybrid energy harvesting systems, and the most elementary energy production process relies on intermittent solar power. Here, it is shown how the ambient mechanical energy leads to water splitting in a photoelectrochemical (PEC) cell boosted by a triboelectric nanogenerator (TENG). In this strategy, a flexible TENG collects and transforms mechanical energy into electric current, which boosts the PEC water splitting via the charged Li‐ion battery. Au nanoparticles are deposited on TiO₂ nanoarrays for extending the available light spectrum to visible part by surface plasmon resonance effect, which yields a photocurrent density of 1.32 mA cm^?2 under AM 1.5 G illumination and 0.12 mA cm^?2 under visible light with a bias of 0.5 V. The TENG‐charged battery boosts the water splitting performance through coupling electrolysis and enhanced electron–hole separation efficiency. The hybrid cell exhibits an instantaneous current more than 9 mA with a working electrode area of 0.3 cm², suggesting a simple but efficient route for simultaneously converting solar radiation and mechanical energy into hydrogen.     

Facile and Efficient Atomic Hydrogenation Enabled Black TiO2 with Enhanced Photo‐Electrochemical Activity via a Favorably Low‐Energy‐Barrier Pathway

Black TiO₂ has demonstrated a great potential for a variety of renewable energy technologies. However, its practical application is heavily hindered due to lack of efficient hydrogenation methods and a deeper understanding of hydrogenation mechanisms. Here, a simple and straightforward hot wire annealing (HWA) method is presented to prepare black TiO₂ (H–TiO₂) nanorods with enhanced photo‐electrochemical (PEC) activity by means of atomic hydrogen [H]. Compared to conventional molecular hydrogen approaches, the HWA shows remarkable effectiveness without any detrimental side effects on the device structure, and simultaneously the photocurrent density of H–TiO₂ reaches 2.5 mA cm^?2 (at 1.23 V vs reversible hydrogen electrode (RHE)). Due to the controllable and reproducible [H] flux, the HWA can be developed as a standard hydrogenation method for black TiO₂. Meanwhile, the relationships between the wire temperatures, structural, optical, and photo‐electrochemical properties are systematically investigated to verify the improved PEC activity. Furthermore, the density functional theory (DFT) study provides a comprehensive insight not only into the highly efficient mechanism of the HWA approach but also its favorably low‐energy‐barrier hydrogenation pathway. The findings will have a profound impact on the broad energy applications of H–TiO₂ and contribute to the fundamental understanding of its hydrogenation.     

MOF‐Based Transparent Passivation Layer Modified ZnO Nanorod Arrays for Enhanced Photo‐Electrochemical Water Splitting

This study introduces zeolitic imidazolate framework‐8 (ZIF‐8) as the first metal‐organic framework based transparent surface passivation layer for photo‐electrochemical (PEC) water splitting. A significant enhancement for PEC water oxidation is demonstrated based on the in situ seamless coating of ZIF‐8 surface passivation layer on Ni foam (NF) supported ZnO nanorod arrays photoanode. The PEC performance is improved by optimizing the ZIF‐8 thickness and by grafting Ni(OH)₂ nanosheets as synergetic co‐catalyst. With respect to ZnO/NF, the optimized Ni(OH)₂/ZIF‐8/ZnO/NF photoanode exhibits a two times larger photocurrent density of 1.95 mA cm^?2 and also a two times larger incident photon to current conversion efficiency of 40.05% (350 nm) at 1.23 V versus RHE (V_RHE) under AM 1.5 G. The synergetic surface passivation and the co‐catalyst modification contribute to prolonging the charge lifetime, to promoting the charge transfer, and to decreasing the overpotential for water oxidation.     

Efficient Nanostructured TiO2/SnS Heterojunction Solar Cells

Tin sulfide (SnS) is one of the most promising solar cell materials, as it is abundant, environment friendly, available at low cost, and offers long‐term stability. However, the highest efficiency of the SnS solar cell reported so far remains at 4.36% even using the expensive atomic layer deposition process. This study reports on the fabrication of SnS solar cells by a solution process that employs rapid thermal treatment for few seconds under Ar gas flow after spin‐coating a precursor solution of SnCl₂ and thiourea dissolved in dimethylformamide onto a nanostructured thin TiO₂ electrode. The best‐performing cell exhibits power conversion efficiency (PCE) of 3.8% under 1 sun radiation conditions (AM1.5G). Moreover, secondary treatment using SnCl₂ results in a significant improvement of 4.8% in PCE, which is one of the highest efficiencies among SnS‐based solar cells, especially with TiO₂ electrodes. The thin film properties of SnS after SnCl₂ secondary treatment are analyzed using grazing‐incidence wide‐angle X‐ray scattering, and high‐resolution transmittance electron microscopy.     

p‐Type CuI Islands on TiO2 Electron Transport Layer for a Highly Efficient Planar‐Perovskite Solar Cell with Negligible Hysteresis

Compact TiO₂ is widely used as an electron transport material in planar‐perovskite solar cells. However, TiO₂‐based planar‐perovskite solar cells exhibit low efficiencies due to intrinsic problems such as the unsuitable conduction band energy and low electron extraction ability of TiO₂. Herein, the planar TiO₂ electron transport layer (ETL) of perovskite solar cells is modified with ionic salt CuI via a simple one‐step spin‐coating process. The p‐type nature of the CuI islands on the TiO₂ surface leads to modification of the TiO₂ band alignment, resulting in barrier‐free contacts and increased open‐circuit voltage. It is found that the polarity of the CuI‐modified TiO₂ surface can pull electrons to the interface between the perovskite and the TiO₂, which improves electron extraction and reduces nonradiative recombination. The CuI solution concentration is varied to control the electron extraction of the modified TiO₂ ETL, and the optimized device shows a high efficiency of 19.0%. In addition, the optimized device shows negligible hysteresis, which is believed to be due to the removal of trap sites and effective electron extraction by CuI‐modified TiO₂. These results demonstrate the hitherto unknown effect of p‐type ionic salts on electron transport material.     

Efficient and Stable TiO2:Pt–Cu(In,Ga)Se2 Composite Photoelectrodes for Visible Light Driven Hydrogen Evolution

Novel thin film composite photocathodes based on device‐grade Cu(In,Ga)Se₂ chalcopyrite thin film absorbers and transparent conductive oxide Pt‐implemented TiO₂ layers on top are presented for an efficient and stable solar‐driven hydrogen evolution. Thin films of phase‐pure anatase TiO₂ are implemented with varying Pt‐concentrations in order to optimize simultaneously i) conductivity of the films, ii) electrocatalytic activity, and iii) light‐guidance toward the chalcopyrite. Thereby, high incident‐photon‐to‐current‐efficiencies of more than 80% can be achieved over the full visible light range. In acidic electrolyte (pH 0.3), the most efficient Pt‐implemented TiO₂–Cu(In,Ga)Se₂ composite electrodes reveal i) photocurrent densities up to 38 mA cm^?2 in the saturation region (?0.4 V RHE, reversible hydrogen electrode), ii) 15 mA cm^?2 at the thermodynamic potential for H₂‐evolution (0 V RHE), and iii) an anodic onset potential shift for the hydrogen evolution (+0.23 V RHE). It is shown that the gradual increase of the Pt‐concentration within the TiO₂ layers passes through an efficiency‐ and stability‐maximum of the device (5 vol% of Pt precursor solution). At this maximum, optimized light‐incoupling into the device‐grade chalcopyrite light‐absorber as well as electron conductance properties within the surface layer are achieved while no degradation are observed over more than 24 h of operation.     

3D‐Branched ZnO/CdS Nanowire Arrays for Solar Water Splitting and the Service Safety Research

Modulation of broadband light trapping through assembly of 3D structures and modification with narrow band‐gap semiconductors provide an effective way to improve the photoelectrochemical (PEC) performance. Here, 3D‐branched ZnO nanowire arrays (NWAs) modified with cadmium sulfide (CdS) nanoparticles are designed and synthesized via solution chemical routes. The 3D‐branched ZnO NWA–CdS nanoparticle photoanodes show an excellent PEC performance in UV and visible region and the maximum photo‐to‐hydrogen conversion efficiency reaches to 3.1%. The high performance of 3D‐branched ZnO NWA–CdS composites is mainly attributed to the excellent carrier collection capability and high light‐trapping ability of 3D‐branched ZnO NWAs as well as the excellent photocatalytic activity of CdS nanoparticles in the visible region. In addition, the photocorrosion mechanism of 3D‐branched ZnO NWA–CdS photoanodes is systematically investigated, and a protective TiO₂ layer is deposited onto the photoanodes to elevate the PEC stability. The results benefit a deeper understanding of the role of 3D‐branched structures decorated with narrow band‐gap semiconductors in solar water splitting.     

Solution‐Processed TiO2 Nanoparticles as the Window Layer for CuIn(S,Se)2 Devices

As a wide‐bandgap semiconductor, titanium dioxide (TiO₂) with a porous structure has proven useful in dye‐sensitized solar cells, but its application in low‐cost, high‐efficiency inorganic photovoltaic devices based on materials such as Cu(InGa)Se₂ or Cu₂ZnSnS₄ is limited. Here, a thin film made from solution‐processed TiO₂ nanocrystals is demonstrated as an alternative to intrinsic zinc oxide (i‐ZnO) as the window layer of CuInS_xSe_1?x solar cells. The as‐synthesized, well‐dispersed, 6 nm TiO₂ nanocrystals are assembled into thin films with controllable thicknesses of 40, 80, and 160 nm. The TiO₂ nanocrystal films with thicknesses of 40 and 80 nm exhibit conversion efficiencies (6.2% and 6.33%, respectively) that are comparable to that of a layer of the typical sputtered i‐ZnO (6.42%). The conversion efficiency of the devices with a TiO₂ thickness of 160 nm decreases to 2.2%, owing to the large series resistance. A 9‐hour reaction time leads to aggregated nanoparticles with a much‐lower efficiency (2%) than that of the well‐dispersed TiO₂ nanoparticles prepared using a 15‐hour reaction time. Under optimized conditions, the champion TiO₂ nanocrystal‐film‐based device shows even higher efficiency (9.2%) than a control device employing a typical i‐ZnO film (8.6%).     

Self‐Assembly Atomic Stacking Transport Layer of 2D Layered Titania for Perovskite Solar Cells with Extended UV Stability

A novel atomic stacking transporting layer (ASTL) based on 2D atomic sheets of titania (Ti_1?δO₂) is demonstrated in organic–inorganic lead halide perovskite solar cells. The atomically thin ASTL of 2D titania, which is fabricated using a solution‐processed self‐assembly atomic layer‐by‐layer deposition technique, exhibits the unique features of high UV transparency and negligible (or very low) oxygen vacancies, making it a promising electron transporting material in the development of stable and high‐performance perovskite solar cells. In particular, the solution‐processable atomically thin ASTL of 2D titania atomic sheets shows superior inhibition of UV degradation of perovskite solar cell devices, compared to the conventional high‐temperature sintered TiO₂ counterpart, which usually causes the notorious instability of devices under UV irradiation. The discovery opens up a new dimension to utilize the 2D layered materials with a great variety of homostructrual or heterostructural atomic stacking architectures to be integrated with the fabrication of large‐area photovoltaic or optoelectronic devices based on the solution processes.     

(040)‐Crystal Facet Engineering of BiVO4 Plate Photoanodes for Solar Fuel Production

A (040)‐crystal facet engineered BiVO₄ ((040)‐BVO) photoanode is investigated for solar fuel production. The (040)‐BVO photoanode is favorable for improved charge carrier mobility and high photocatalytic active sites for solar light energy conversion. This crystal facet design of the (040)‐BVO photoanode leads to an increase in the energy conversion efficiency for solar fuel production and an enhancement of the oxygen evolution rate. The photocurrent density of the (040)‐BVO photoanode is determined to be 0.94 mA cm^?2 under AM 1.5 G illumination and produces 42.1% of the absorbed photon‐to‐current conversion efficiency at 1.23 V (vs RHE, reversible hydrogen electrode). The enhanced charge separation efficiency and improved charge injection efficiency driven by (040) facet can produce hydrogen with 0.02 mmol h^?1 at 1.23 V. The correlation between the (040)‐BVO photoanode and the solar fuel production is investigated. The results provide a promising approach for the development of solar fuel production using a BiVO₄ photoanode.     

Boosting Photoelectrochemical Water Oxidation of Hematite in Acidic Electrolytes by Surface State Modification

State‐of‐the‐art water‐oxidation catalysts (WOCs) in acidic electrolytes usually contain expensive noble metals such as ruthenium and iridium. However, they too expensive to be implemented broadly in semiconductor photoanodes for photoelectrochemical (PEC) water splitting devices. Here, an Earth‐abundant CoFe Prussian blue analogue (CoFe‐PBA) is incorporated with core–shell Fe₂O₃/Fe₂TiO₅ type II heterojunction nanowires as composite photoanodes for PEC water splitting. Those deliver a high photocurrent of 1.25 mA cm^?2 at 1.23 V versus reversible reference electrode in acidic electrolytes (pH = 1). The enhancement arises from the synergic behavior between the successive decoration of the hematite surface with nanolayers of Fe₂TiO₅ and then, CoFe‐PBA. The underlying physical mechanism of performance enhancement through formation of the Fe₂O₃/Fe₂TiO₅/CoFe‐PBA heterostructure reveals that the surface states’ electronic levels of hematite are modified such that an interfacial charge transfer becomes kinetically favorable. These findings open new pathways for the future design of cheap and efficient hematite‐based photoanodes in acidic electrolytes.