Acetone–butanol–ethanol production from corn stover pretreated by alkaline twin-screw extrusion pretreatment

In this study, the alkaline twin-screw extrusion pretreated corn stover was subjected to enzymatic hydrolysis after washing. The impact of solid loading and enzyme dose on enzymatic hydrolysis was investigated. It was found that 68.2 g/L of total fermentable sugar could be obtained after enzymatic hydrolysis with the solid loading of 10 %, while the highest sugar recovery of 91.07 % was achieved when the solid loading was 2 % with the cellulase dose of 24 FPU/g substrate. Subsequently, the hydrolyzate was fermented by Clostridium acetobutylicum ATCC 824. The acetone–butanol–ethanol (ABE) production of the hydrolyzate was compared with the glucose, xylose and simulated hydrolyzate medium which have the same reducing sugar concentration. It was shown that 7.1 g/L butanol and 11.2 g/L ABE could be produced after 72 h fermentation for the hydrolyzate obtained from enzymatic hydrolysis with 6 % solid loading. This is comparable to the glucose and simulated hydrozate medium, and the overall ABE yield could reach 0.112 g/g raw corn stover.     

Recent progress on industrial fermentative production of acetone–butanol–ethanol by Clostridium acetobutylicum in China

China is one of the few countries, which maintained the fermentative acetone–butanol–ethanol (ABE) production for several decades. Until the end of the last century, the ABE fermentation from grain was operated in a few industrial scale plants. Due to the strong competition from the petrochemical industries, the fermentative ABE production lost its position in the 1990s, when all the solvent fermentation plants in China were closed. Under the current circumstances of concern about energy limitations and environmental pollution, new opportunities have emerged for the traditional ABE fermentation industry since it could again be potentially competitive with chemical synthesis. From 2006, several ABE fermentation plants in China have resumed production. The total solvent (acetone, butanol, and ethanol) production capacity from ten plants reached 210,000 tons, and the total solvent production is expected to be extended to 1,000,000 tons (based on the available data as of Sept. 2008). This article reviews current work in strain development, the continuous fermentation process, solvent recovery, and economic evaluation of ABE process in China. Challenges for an economically competitive ABE process in the future are also discussed.     

Direct fermentation of gelatinized sago starch to acetone–butanol–ethanol by Clostridium acetobutylicum

Direct fermentation of gelatinized sago starch into solvent (acetone–butanol–ethanol) by Clostridium acetobutylicum P262 was studied using a 250 ml Schott bottle anaerobic fermentation system. Total solvent production from fermentation using 30 g sago starch/l (11.03g/l) was comparable to fermentation using corn starch and about 2-fold higher than fermentation using potato or tapioca starch. At the range of sago starch concentration investigated (10–80 g/l), the highest total solvent production (18.82 g/l) was obtained at 50 g/l. The use of a mixture of organic and inorganic nitrogen source (yeast extract + NH₄NO₃) enhanced growth of C. acetobutylicum, starch hydrolysis and solvent production (24.47 g/l) compared to the use of yeast extract alone. This gave the yield based on sugar consumed of 0.45 g/g. Result from this study also showed that the individual concentrations of nitrogen and carbon influenced solvent production to a greater extent than did carbon to nitrogen (C/N) ratio.     

Continuous bio-catalytic conversion of sugar mixture to acetone–butanol–ethanol by immobilized <Emphasis Type="Italic">Clostridium acetobutylicum</Emphasis> DSM 792

Continuous production of acetone, n-butanol, and ethanol (ABE) was carried out using immobilized cells of Clostridium acetobutylicum DSM 792 using glucose and sugar mixture as a substrate. Among various lignocellulosic materials screened as a support matrix, coconut fibers and wood pulp fibers were found to be promising in batch experiments. With a motive of promoting wood-based bio-refinery concept, wood pulp was used as a cell holding material. Glucose and sugar mixture (glucose, mannose, galactose, arabinose, and xylose) comparable to lignocellulose hydrolysate was used as a substrate for continuous production of ABE. We report the best solvent productivity among wild-type strains using column reactor. The maximum total solvent concentration of 14.32 g L⁻¹ was obtained at a dilution rate of 0.22 h⁻¹ with glucose as a substrate compared to 12.64 g L⁻¹ at 0.5 h⁻¹ dilution rate with sugar mixture. The maximum solvent productivity (13.66 g L⁻¹ h⁻¹) was obtained at a dilution rate of 1.9 h⁻¹ with glucose as a substrate whereas solvent productivity (12.14 g L⁻¹ h⁻¹) was obtained at a dilution rate of 1.5 h⁻¹ with sugar mixture. The immobilized column reactor with wood pulp can become an efficient technology to be integrated with existing pulp mills to convert them into wood-based bio-refineries.     

Targeted mutagenesis of the Clostridium acetobutylicum acetone–butanol–ethanol fermentation pathway

The production of the chemical solvents acetone and butanol by the bacterium Clostridium acetobutylicum was one of the first large-scale industrial processes to be developed, and in the first part of the last century ranked second in importance only to ethanol production. After a steep decline in its industrial use, there has been a recent resurgence of interest in the acetone–butanol–ethanol (ABE) fermentation process, with a particular emphasis on butanol production. In order to generate strains suitable for efficient use on an industrial scale, metabolic engineering is required to alter the AB ratio in favour of butanol, and eradicate the production of unwanted products of fermentation. Using ClosTron technology, a large-scale targeted mutagenesis in C. acetobutylicum ATCC 824 was carried out, generating a set of 10 mutants, defective in alcohol/aldehyde dehydrogenases 1 and 2 (adhE1, adhE2), butanol dehydrogenases A and B (bdhA, bdhB), phosphotransbutyrylase (ptb), acetate kinase (ack), acetoacetate decarboxylase (adc), CoA transferase (ctfA/ctfB), and a previously uncharacterised putative alcohol dehydrogenase (CAP0059). However, inactivation of the main hydrogenase (hydA) and thiolase (thl) could not be achieved. Constructing such a series of mutants is paramount for the acquisition of information on the mechanism of solvent production in this organism, and the subsequent development of industrial solvent producing strains. Unexpectedly, bdhA and bdhB mutants did not affect solvent production, whereas inactivation of the previously uncharacterised gene CAP0059 resulted in increased acetone, butanol, and ethanol formation. Other mutants showed predicted phenotypes, including a lack of acetone formation (adc, ctfA, and ctfB mutants), an inability to take up acids (ctfA and ctfB mutants), and a much reduced acetate formation (ack mutant). The adhE1 mutant in particular produced very little solvents, demonstrating that this gene was indeed the main contributor to ethanol and butanol formation under the standard batch culture conditions employed in this study. All phenotypic changes observed could be reversed by genetic complementation, with exception of those seen for the ptb mutant. This mutant produced around 100 mM ethanol, no acetone and very little (7 mM) butanol. The genome of the ptb mutant was therefore re-sequenced, together with its parent strain (ATCC 824 wild type), and shown to possess a frameshift mutation in the thl gene, which perfectly explained the observed phenotype. This finding reinforces the need for mutant complementation and Southern Blot analysis (to confirm single ClosTron insertions), which should be obligatory in all further ClosTron applications.     

Promotion of the Clostridium acetobutylicum ATCC 824 growth and acetone–butanol–ethanol fermentation by flavonoids

An unexpected promotion effect of Ginkgo leaf on the growth of Clostridium acetobutylicum ATCC 824 and acetone–butanol–ethanol (ABE) fermentation was investigated. Component analysis of Ginkgo leaf was carried out and flavonoids were determined as the potential key metabolites. Then the flavonoids feeding experiments were carried out. Results showed that addition of only 10 mg/L flavonoids to the fermentation broth can promote butanol and ABE titre up to 14.5 and 17.8 g/L after 5 days of fermentation, that is, 74 and 68 % higher than the control. A 2.2-fold biomass also has been achieved. Furthermore, by employing such novel founding, we easily exploited flavonoids from soybean and some agriculture wastes as the wide-distributed and economic feasible ABE fermentation promoter. The mechanism of the above effects was investigated from the perspective of oxidation–reduction potential. This work opens a new way in the efforts to increase the titer of butanol.     

Production of acetone–butanol–ethanol (ABE) in a continuous flow bioreactor using degermed corn and Clostridium beijerinckii

An examination of the sustainability of the long-term cultivation of C. beijerinckii BA101 in degermed corn/saccharified degermed corn based P2 medium has been described in this work. It was found that long-term continuous cultivation of C. beijerinckii BA101 in a degermed corn based medium was not possible due to the instability of the gelatinized degermed corn starch during storage often called “retrogradation”. Using this substrate, continuous ABE fermentation was run for 228 h, before the fermentation turned acidogenic. However continuous fermentations of saccharified degermed corn with normal and half P2 medium nutrients were successful. In saccharified degermed corn continuous fermentation, ABE concentration up to 14.28 g/L was achieved at a dilution rate of 0.03 h⁻¹. This work demonstrated that byproduct (germ/oil, corn fiber) credit can be obtained by fermenting saccharified degermed corn in continuous flow bioreactors. Additionally significant savings can be achieved by supplementing with half of normal P2 medium nutrients.     

Acetone–butanol–ethanol fermentation of corn stover by Clostridium species: present status and future perspectives

Sustainable vehicle fuel is indispensable in future due to worldwide depletion of fossil fuel reserve, oil price fluctuation and environmental degradation. Microbial production of butanol from renewable biomass could be one of the possible options. Renewable biomass such as corn stover has no food deficiency issues and is also cheaper in most of the agricultural based countries. Thus it can effectively solve the existing issue of substrate cost. In the last 30 years, a few of Clostridium strains have been successfully implemented for biobutanol fermentation. However, the commercial production is hindered due to their poor tolerance to butanol and inhibitors. Metabolic engineering of Clostridia strains is essential to solve above problems and ultimately enhance the solvent production. An effective and efficient pretreatment of raw material as well as optimization of fermentation condition could be another option. Furthermore, biological approaches may be useful to optimize both the host and pathways to maximize butanol production. In this context, this paper reviews the existing Clostridium strains and their ability to produce butanol particularly from corn stover. This study also highlights possible fermentation pathways and biological approaches that may be useful to optimize fermentation pathways. Moreover, challenges and future perspectives are also discussed.     

Simultaneous acetone–butanol–ethanol fermentation,gas stripping,and full-cell-catalyzed esterification for effective production of butyl oleate

Bioprocess and Biosystems Engineering - In this study, aiming to improve the economic feasibility of acetone–butanol–ethanol (ABE) fermentation process, generate valuable products and...     

Continuous ethanol production by thermotolerant Kluyveromyces marxianus IMB3 immobilized on mineral Kissiris at 45°C

Thermotolerant Kluyveromyces marxianus var. marxianus IMB3 yeast strain was immobilized on Kissiris (mineral glass foam derived from lava) in column packed reactors, and used for ethanol production from glucose or molasses under continuous culture conditions at temperatures between 40 and 50°C. Both ethanol yield and fermentation efficiency were highest at 45°C and a dilution rate (D) of 0.15/h. Increasing sugar concentration led to an increase in ethanol yield of up to 68.6 and 55.9 g/l on approx. 200g glucose or molasses, respectively. Optimum fermentation efficiency (experimental yields over theoretical maximum yields) however was at about 15% sugar for both glucose and molasses. Slight aeration (25 ml of air/min) through the medium addition line was found advantageous due to its mixing effect and probable maintenance of activity.     

Ionic liquid-based in situ product removal design exemplified for an acetone–butanol–ethanol fermentation

Selecting an appropriate separation technique is essential for the application of in situ product removal (ISPR) technology in biological processes. In this work, a three-stage systematic design method is proposed as a guide to integrate ionic liquid (IL)-based separation techniques into ISPR. This design method combines the selection of a suitable ISPR processing scheme, the optimal design of an IL-based liquid–liquid extraction (LLE) system followed by process simulation and evaluation. As a proof of concept, results for a conventional acetone–butanol–ethanol fermentation are presented (40,000 ton/year butanol production). In this application, ILs tetradecyl(trihexyl)phosphonium tetracyanoborate ([TDPh][TCB]) and tetraoctylammonium 2-methyl-1-naphthoate ([TOA] [MNaph]) are identified as the optimal solvents from computer-aided IL design (CAILD) method and reported experimental data, respectively. The dynamic simulation results for the fermentation process show that, the productivity of IL-based in situ (fed-batch) process and in situ (batch) process is around 2.7 and 1.8fold that of base case. Additionally, the IL-based in situ (fed-batch) process and in situ (batch) process also have significant energy savings (79.6% and 77.6%) when compared to the base case.     

α-Amylase production by immobilized whole cells of Bacillus subtilis

Summary Whole cells of Bacillus subtilis were immobilized in polyacrylamide gel prepared from 5% total acrylamide (85% acrylamide and 15% N,N-methylenebisacrylamide). Production of -amylase by the immobilized whole cells was attempted in a batch system. -Amylase produced by the immobilized whole cells was about three times larger than that produced by washed cells at optimum conditions. The reusability of the immobilized whole cells and washed cells was examined. The activity of -amylase production by washed cells decreased with increasing use cycles. On the other hand, the activity of the immobilized cells increased gradually, and it reched a steady state after seven cycles. -Amylase was produced from a simple reaction medium containing 1% meat extract and 0.05% yeast extract by the immobilized whole cells. The rate of -amylase production by the immobilized whole cells was the same as in submerged cultivation using starch bouillon medium. Growth of B. subtilis in polyacrylamide gel was observed by electron microscopy.     

Microbial production of a biofuel (acetone–butanol–ethanol) in a continuous bioreactor: impact of bleed and simultaneous product removal

Acetone butanol ethanol (ABE) was produced in an integrated continuous one-stage fermentation and gas stripping product recovery system using Clostridium beijerinckii BA101 and fermentation gases (CO₂ and H₂). In this system, the bioreactor was fed with a concentrated sugar solution (250–500 g L^?1 glucose). The bioreactor was bled semi-continuously to avoid accumulation of inhibitory chemicals and products. The continuous system was operated for 504 h (21 days) after which the fermentation was intentionally terminated. The bioreactor produced 461.3 g ABE from 1,125.0 g total sugar in 1 L culture volume as compared to a control batch process in which 18.4 g ABE was produced from 47.3 g sugar. These results demonstrate that ABE fermentation can be operated in an integrated continuous one-stage fermentation and product recovery system for a long period of time, if butanol and other microbial metabolites in the bioreactor are kept below threshold of toxicity.     

Continuous production of α-peptide using immobilized recombinant yeast cells: A model for continuous production of foreign peptide by recombinant yeast

α-Peptide, a portion of Escherichia coli β-galactosidase, was cloned downstream of the yeast α-factor promoter and the signal peptide by one of the authors. In this study, we utilized recombinant yeast cells, transformed the α-peptide secretion vector and attempted continuous production of α-peptide as a model of foreign peptide production. The continuous production of α-peptide was performed by using immobilized recombinant yeast cells on a column reactor, after characterizing the secretion, using minimal and complex medium. Utilizing minimal medium, with a productivity of 100 000 U h⁻¹ l⁻¹, α-peptide was continuously produced for more than 200 h. We then attempted to improve the productivity of α-peptide by alternating minimal and complex medium. Utilizing this medium changing method, 1.4 times higher α-peptide was produced during 150 h of operation compared with that achieved only by feeding minimal medium.     

Continuous production of β-cyclodextrin from starch by highly stable cyclodextrin glycosyltransferase immobilized on chitosan

Cyclodextrin glycosyltransferase (CGTase) from Thermoanaerobacter sp. was covalently immobilized on glutaraldehyde-activated chitosan spheres and used in a packed bed reactor to investigate the continuous production of β-cyclodextrin (β-CD). The optimum temperatures were 75 °C and 85 °C at pH 6.0, respectively for free and immobilized CGTase, and the optimum pH (5.0) was the same for both at 60 °C. In the reactor, the effects of flow rate and substrate concentration in the β-CD production were evaluated. The optimum substrate concentration was 4% (w/v), maximizing the β-CD production (1.32 g/L) in a flow rate of 3 mL/min. In addition, the biocatalyst had good operational stability at 60 °C, maintaining 61% of its initial activity after 100 cycles of batch and 100% after 100 h of continuous use. These results suggest the possibility of using this immobilized biocatalyst in continuous production of CDs.     

Mechanistic simulation of batch acetone–butanol–ethanol (ABE) fermentation with in situ gas stripping using Aspen Plus™

Bioprocess and Biosystems Engineering - Process simulations of batch fermentations with in situ product separation traditionally decouple these interdependent steps by simulating a separate...     

Combining chemical flocculation and bacterial co-culture of Cupriavidus taiwanensis and Ureibacillus thermosphaericus to detoxify a hardwood hemicelluloses hydrolysate and enable acetone–butanol–ethanol fermentation leading to butanol

Butanol, a fuel with better characteristics than ethanol, can be produced via acetone–butanol–ethanol (ABE) fermentation using lignocellulosic biomass as a carbon source. However, many inhibitors present in the hydrolysate limit the yield of the fermentation process. In this work, a detoxification technology combining flocculation and biodetoxification within a bacterial co-culture composed of Ureibacillus thermosphaericus and Cupriavidus taiwanensis is presented for the first time. Co-culture-based strategies to detoxify filtered and unfiltered hydrolysates have been investigated. The best results of detoxification were obtained for a two-step approach combining flocculation to biodetoxification. This sequential process led to a final phenolic compounds concentration of 1.4 g/L, a value close to the minimum inhibitory level observed for flocculated hydrolysate (1.1 g/L). The generated hydrolysate was then fermented with Clostridium acetobutylicum ATCC 824 for 120 h. A final butanol production of 8 g/L was obtained, although the detoxified hydrolysate was diluted to reach 0.3 g/L of phenolics to ensure noninhibitory conditions. © 2018 American Institute of Chemical Engineers Biotechnol. Prog., 35: e2753, 2019.     

Continuous production of galacto-oligosaccharides from lactose by Bullera singularis β-galactosidase immobilized in chitosan beads

Galacto-oligosaccharides (GalOS) were continuously produced using lactose and immobilized β-galactosidase from Bullera singularis ATCC 24193 in a packed bed reactor. Partially purified β-galactosidase was immobilized in Chitopearl BCW 3510 bead (970 GU/g resin) by simple adsorption. 55% (w/w) oligosaccharides was obtained continuously with a productivity of 4·4 g/(litre-h) from 100 g/litre lactose solution during a 15-day operation. Batch productivity was 6·5 g GalOS/(litre-h) from 300 g/litre lactose.     

Physiology of α-amylase production by immobilized Bacillus amyloliquefaciens

Summary Bacillus amyloliquefaciens 321S cells were immobilized with 3.4% -carrageenan gel in bead form, and -amylase production by the immobilized cells was studied. Cells in the gel, after the population reached maximum were restricted to a layer of 50 m thickness, from the surface of the gel, suggesting that oxygen diffusion is the growth limiting factor. The specific respiratory activity and the growth rate of the entrapped cells under such conditions were 1/2 and 1/5 1/10, respectively, that of free cells. In spite of the repressed respiration and growth, the specific rate of -amylase production of the entrapped cells reached the maximum value of free cells or higher.In continuous culture, in an aerated vessel with a volume ratio of gel beads to medium of 1:2, the maximum production rate of -amylase was obtained at a dilution rate of 1.0 h^–1, which was double the maximum specific growth rate of the strain.These results showed that bacterial -amylase production, which is a nongrowth-associated type of synthesis was achieved with the use of immobilized cells.     

Cellulase production by Trichoderma reesei immobilized on κ-carrageenan

Summary Cellulase production by Trichoderma reesei mutant RUT-C30, immobilized on 4% -carrageenan beads, was monitored in continuous culture for 13 days. Cellulase production averaged 26.0 Filter Paper Units (FPU)/l/hr; carbon and nitrogen requirements per FPU produced were reduced to 1/4-1/2 those of conventional continuous culture.