Acid hydrolysis of sweet potato for ethanol production

Studies were conducted to establish optimal conditions for the acid hydrolysis of sweet potato for maximal ethanol yield. The starch contents of two sweet potato cultivars (Georgia Red and TG-4), based on fresh weight, were 21.1 +/- 0.6% and 27.5 +/- 1.6%, respectively. The results of acid hydrolysis experiments showed the following: (1) both hydrolysis rate and hydroxymethylfurfural (HMF) concentration were a function of HCL concentration, temperature, and time; (2) the reducing sugars were rapidly formed with elevated concentrations of HCl and temperature, but also destroyed quickly; and (3) HMF concentration increased significantly with the concentration of HCl, temperature, and hydrolysis time.Maximum reducing sugar value of 84.2 DE and 0.056% HMF (based on wet weight) was achieved after heating 8% SPS for 15 min in 1N HCl at 110 degrees C. Degraded 8% SPS (1N HCl, 97 degrees C for 20 min or 110 degrees C for 10 min) was utilized as substrate for ethanol fermentation and 3.8% ethanol (v/v) was produced from 1400 mL fermented wort. This is equal to 41.6 g ethanol (200 proof) from 400 g of fresh sweet potato tuber (Georgia Red) or an ethanol yield potential of 431 gal of 200-proof ethanol/acre (from 500 bushel tubers/acre).     

Steam pretreatment of H(2)SO(4)-impregnated Salix for the production of bioethanol

In the bioconversion of lignocellulosic materials to ethanol, pretreatment of the material prior to enzymatic hydrolysis is essential to obtain high overall yields of sugar and ethanol. In this study, steam pretreatment of fast-growing Salix impregnated with sulfuric acid has been investigated by varying the temperature (180-210 degrees C), the residence time (4, 8 or 12 min), and the acid concentration (0.25% or 0.5% (w/w) H(2)SO(4)). High sugar recoveries were obtained after pretreatment, and the highest yields of glucose and xylose after the subsequent enzymatic hydrolysis step were 92% and 86% of the theoretical, respectively, based on the glucan and xylan contents of the raw material. The most favorable pretreatment conditions regarding the overall sugar yield were 200 degrees C for either 4 or 8 min using 0.5% sulfuric acid, both resulting in a total of 55.6g glucose and xylose per 100g dry raw material. Simultaneous saccharification and fermentation experiments were performed on the pretreated slurries at an initial water-insoluble content of 5%, using ordinary baker's yeast. An overall theoretical ethanol yield of 79%, based on the glucan and mannan content in the raw material, was obtained.     

Bioconversion of wheat straw cellulose/hemicellulose to ethanol by Saccharomyces uvarum and Pachysolen tannophilus

The information presented in this publication represents current research findings on the production of glucose and xylose from straw and subsequent direct fermentation of both sugars to ethanol. Agricultural straw was subjected to thermal or alkali pulping prior to enzymatic saccharification. When wheat straw (WS) was treated at 170 degrees C for 30-60 min at a water-to-solids ratio of 7:1, the yield of cellulosic pulp was 70-82%. A sodium hydroxide extration yielded a 60% cellulosic pulp and a hemicellulosic fraction available for fermentation to ethanol. The cellulosic pulps were subjected to cellulase hydrolysis at 55 degrees C for production of sugars to support a 6-C fermentation. Hemicellulose was recovered from the liquor filtrates by acid/alcohol precipitation followed by acid hydrolysis to xylose for fermentation. Subsequent experiments have involved the fermentation of cellulosic and hemicelluosic hydrolysates to ethanol. Apparently these fermentations were inhibited by substances introduced by thermal and alkali treatment of the straws, because ethanol efficiencies of only 40-60% were achieved. Xylose from hydrolysis of wheat straw pentosans supported an ethanol fermentation by Pachysolen tannophilus strain NRRL 2460. This unusual yeast is capable of producing ethanol from both glucose and xylose. Ethanol yields were not maximal due to deleterious substances in the WS hydrolysates.     

Ethanol fermentation of acid-hydrolyzed cellulosic pyrolysate with Saccharomyces cerevisiae

The acid hydrolysis of cellulosic pyrolysate to glucose and its fermentation to ethanol were investigated. The maximum glucose yield (17.4%) was obtained by the hydrolysis with 0.2 mol sulfuric acid per liter pyrolysate using autoclaving at 121 degrees C for 20 min. The fermentation by Saccharomyces cerevisiae of a hydrolysate medium containing 31.6 g/l glucose gave 14.2 g/l ethanol in 24 h, whereas the fermentation of the medium containing 31.6 g/l pure glucose gave 13.7 g/l ethanol in 18 h. The results showed that the acid-hydrolyzed pyrolysate could be used for ethanol production. Different nitrogen sources were evaluated and the best ethanol concentration (15.1 g/l) was achieved by single urea. S. cerevisiae (R) was obtained by adaptation of S. cerevisiae to the hydrolysate medium for 12 times, and 40.2 g/l ethanol was produced by S. cerevisiae (R) in the fermentation with the hydrolysate medium containing 95.8 g/l glucose, which was about 47% increase in ethanol production compared to its parent strain.     

Temperature cycling to improve the ethanol production with solid state simultaneous saccharification and fermentation

Simultaneous saccharification and fermentation (SSF) widely used in submerged state could be effective in solid state. Solid state SSF was first compared with solid state separate hydrolysis and fermentation on ethanol production. Ethanol yield using solid state separate hydrolysis and fermentation (SHF) in 5 days was only half of that in solid state SSF in 3 days. In solid state SSF, the ethanol concentration using temperature cycling (10 h at 37 degrees C followed by 15 min at 42 degrees C) was 2 times that using constant 37 degrees C within 72 h, reached 5.2%.     

Fermentation of cellodextrins to ethanol using mixed-culture fermentations

The potential for enhancing ethanol production from cellodextrins by employing mixed-culture (Candida wickerhamii-Saccharomyces cerevisiae) fermentations was investigated. Initially, ethanol production was monitored in fermentation medium containing 50 g/L glucose plus 45 g/L cellobiose. Inoculum levels and times of inoculum addition were varied. Of the conditions tested, the most rapid rates of ethanol formation occurred in fermentations in which either C. wickerhamii and S. cerevisiae were coinoculated at a ratio of 57 : 1 cell/mL or in fermentations in which a 10-fold-greater S. cerevisiae inoculum was added to a pure culture C. wickerhamii fermentation after 1 day incubation. These conditions were used to attempt to enhance fermentations in which cellodextrins produced by trifluoroacetic acid hydrolysis of cellulose served as the sole carbon source. Cellodextrins that were not further purified after cellulose hydrolysis contained compounds that were slightly inhibitory to C. wickerhamii. In this case the mixed-culture fermentations produced 12-45% more ethanol than a pure culture C. wickerhamii fermentation. However, if the substrate was treated with Darco G-60 charcoal, the toxic materials were apparently removed and the pure culture C. wickerhamii fermentations performed as well as the mixed-culture fermentations.     

Production of fuel ethanol from bamboo by concentrated sulfuric acid hydrolysis followed by continuous ethanol fermentation

An efficient process for the production of fuel ethanol from bamboo that consisted of hydrolysis with concentrated sulfuric acid, removal of color compounds, separation of acid and sugar, hydrolysis of oligosaccharides and subsequent continuous ethanol fermentation was developed. The highest sugar recovery efficiency was 81.6% when concentrated sulfuric acid hydrolysis was carried out under the optimum conditions. Continuous separation of acid from the saccharified liquid after removal of color compounds with activated carbon was conducted using an improved simulated moving bed (ISMB) system, and 98.4% of sugar and 90.5% of acid were recovered. After oligosaccharide hydrolysis and pH adjustment, the unsterilized saccharified liquid was subjected to continuous ethanol fermentation using Saccharomycescerevisiae strain KF-7. The ethanol concentration, the fermentation yield based on glucose and the ethanol productivity were approximately 27.2 g/l, 92.0% and 8.2 g/l/h, respectively. These results suggest that the process is effective for production of fuel ethanol from bamboo.     

Optimization of medium constituents and fermentation conditions for the production of ethanol from palmyra jaggery using response surface methodology

The quantitative effects of sugar concentration, nitrogen concentration, EDTA, temperature, pH and time of fermentation on ethanol production were optimized using a Box-Wilson central composite design (CCD) experiment. It was found that palmyra jaggery (sugar syrup from the palmyra palm) is a suitable substrate for the production of high concentrations of ethanol using Saccharomyces cerevisiae NCIM 3090 by submerged fermentation. A maximum ethanol concentration of 129.4 g/l was obtained after optimizing media components and conditions of fermentation. The optimum values were a temperature of 26.2 °C, pH of 8.4, time of fermentation of 4.2 days with 398.5 g of substrate/l, 3.1 g of urea/l and 0.51 g of EDTA/l. Thus by using the CCD, it is possible to determine the accurate values of the fermentation parameters where maximum production of ethanol occurs.     

Solid-state fermentation of sweet sorghum to ethanol

Solid-state fermentation of chopped sweet sorghum particles to ethanol was studied in static flasks using an ethanol tolerant yeast strain. The influence of various process parameters, such as temperature, yeast cell concentration, and moisture content, on the rate and extent of ethanol fermentation was investigated. Optimal values of these parameters were found to be 35 degrees C, 7 x 10(8) cells/g raw sorghum, and 70% moisture level, respectively.     

Designing simultaneous saccharification and fermentation for improved xylose conversion by a recombinant strain of Saccharomyces cerevisiae

Wheat straw is an abundant agricultural residue which can be used as a raw material for bioethanol production. Due to the high xylan content in wheat straw, fermentation of both xylose and glucose is crucial to meet desired overall yields of ethanol. In the present work a recombinant xylose fermenting strain of Saccharomyces cerevisiae, TMB3400, cultivated aerobically on wheat straw hydrolysate, was used in simultaneous saccharification and fermentation (SSF) of steam pretreated wheat straw. The influence of fermentation strategy and temperature was studied in relation to xylose consumption, ethanol formation and by-product formation. In addition, model SSF experiments were made to further investigate the influence of temperature on xylose fermentation and by-product formation. In particular for SSF at the highest value of fibre content tested (9% water insoluble substance, WIS), it was found that a fed-batch strategy was clearly superior to the batch process in terms of ethanol yield, where the fed-batch gave 71% of the theoretical yield (based on all available sugars) in comparison to merely 59% for the batch. Higher ethanol yields, close to 80%, were obtained at a WIS-content of 7%. Xylose fermentation significantly contributed to the overall ethanol yields. The choice of temperature in the range 30-37 degrees C was found to be important, especially at higher contents of water insoluble solids (WIS). The optimum temperature was found to be 34 degrees C for the raw material and yeast strain studied. Model SSF experiments with defined medium showed strong temperature effects on the xylose uptake rate and xylitol yield.     

Ethanol fermentation of acid-hydrolyzed cellulosic pyrolysate with Saccharomyces cerevisiae

Acid-hydrolysis of cellulosic pyrolysate to glucose and its fermentation to ethanol were investigated. The maximum glucose yield (17.4%) was obtained by the hydrolysis with 0.2 mol/l sulfuric acid using autoclaving at 121 degrees C for 20 min. The fermentation by Saccharomyces cerevisiae of a hydrolysate medium containing 31.6 g/l glucose gave 14.2 g/l ethanol after 24 h, whereas the fermentation of the medium containing 31.6 g/l pure glucose gave 13.7 g/l ethanol after 18 h. The results showed that acid-hydrolyzed pyrolysate could be used for ethanol production. Different nitrogen sources were evaluated and the best ethanol concentration (15.1 g/l) was achieved by single urea. S. cerevisiae (R) was obtained by adaptation of S. cerevisiae to the hydrolysate medium for 12 times, and 40.2 g/l ethanol was produced by it in the fermentation with the hydrolysate medium containing 95.8 g/l glucose, which was about 47% increase in ethanol production compared to its parent strain.     

Optimization of fermentation conditions for the production of ethanol from sago starch using response surface methodology

The quantitative effects of temperature, pH and time of fermentation were investigated on simultaneous saccharification and fermentation (SSF) of ethanol from sago starch with glucoamylase (AMG) and Zymomonas mobilis ZM4 using a Box–Wilson central composite design protocol. The SSF process was studied using free enzyme and free cells and it was found that with sago starch, maximum ethanol concentration of 70.68 g/l was obtained using a starch concentration of 140 g/l, which represents an ethanol yield of 97.08%. The optimum conditions for the above yield were found to be a temperature of 36.74 °C, pH of 5.02 and time of fermentation of 17 h. Thus by using the central composite design, it is possible to determine the accurate values of the fermentation parameters where maximum production of ethanol occurs.     

Bioethanol production from non-starch carbohydrate residues in process streams from a dry-mill ethanol plant

Slurries obtained from process streams in a starch-to-ethanol plant, Agroetanol AB in Norrk?ping, Sweden, were used to assess the potential increase in bioethanol yield if heat treatment followed by enzymatic hydrolysis were applied to the residual starch-free cellulose and hemicellulose fractions. The effects of different pretreatment conditions on flour (the raw material), the stream after saccharification of starch, before fermentation, and after fermentation were studied. The conditions resulting in the highest concentration of glucose and xylose in all streams were heat treatment at 130 degrees C for 40 min with 1% H(2)SO(4). Mass-balance calculations over the fermentation showed that approximately 64%, 54%, 75% and 67% of the glucan, xylan, galactan and arabinan, respectively, in the flour remained water insoluble in the process stream after fermentation without any additional treatment. Utilizing only the starch in the flour would theoretically yield 425 L ethanol per ton flour. By applying heat pretreatment to the water-insoluble material prior to enzymatic hydrolysis, the ethanol yield could be increased by 59 L per ton flour, i.e. a 14% increase compared with starch-only utilization, assuming fermentation of the additional pentose and hexose sugars liberated.     

Effect of substrate and cellulase concentration on simultaneous saccharification and fermentation of steam-pretreated softwood for ethanol production

Economic optimization of the production of ethanol by simultaneous saccharification and fermentation (SSF) requires knowledge about the influence of substrate and enzyme concentration on yield and productivity. Although SSF has been investigated extensively, the optimal conditions for SSF of softwoods have yet not been determined. In this study, SO2-impregnated and steam-pretreated spruce was used as substrate for the production of ethanol by SSF. Commercial enzymes were used in combination with the yeast Saccharomyces cerevisiae. The effects of the concentration of substrate (2% to 10% w/w) and of cellulases (5 to 32 FPU/g cellulose) were investigated. SSF was found to be sensitive to contamination because lactic acid was produced. The ethanol yield increased with increasing cellulase loading. The highest ethanol yield, 68% of the theoretical based on the glucose and mannose present in the original wood, was obtained at 5% substrate concentration. This yield corresponds to 82% of the theoretical based on the cellulose and soluble glucose and mannose present at the start of SSF. A higher substrate concentration caused inefficient fermentation, whereas a lower substrate concentration, 2%, resulted in increased formation of lactic acid, which lowered the yield. Compared with separate hydrolysis and fermentation, SSF gave a higher yield and doubled the productivity.     

High-solid enzymatic hydrolysis and fermentation of solka floc into ethanol

To lower the cost of ethanol distillation of fermentation broths, a high initial glucose concentration is desired. However, an increase in the substrate concentration typically reduces the ethanol yield because of insufficient mass and heat transfer. In addition, different operating temperatures are required to optimize the enzymatic hydrolysis (50 degrees ) and fermentation (30 degrees ). Thus, to overcome these incompatible temperatures, saccharification followed by fermentation (SFF) was employed with relatively high solid concentrations (10% to 20%) using a portion loading method. In this study, glucose and ethanol were produced from Solka Floc, which was first digested by enzymes at 50 degrees for 48 h, followed by fermentation. In this process, commercial enzymes were used in combination with a recombinant strain of Zymomonas mobilis (39679:pZB4L). The effects of the substrate concentration (10% to 20%, w/v) and reactor configuration were also investigated. In the first step, the enzyme reaction was achieved using 20 FPU/g cellulose at 50 degrees for 96 h. The fermentation was then performed at 30 degrees for 96 h. The enzymatic digestibility was 50.7%, 38.4%, and 29.4% after 96 h with a baffled Rushton impeller and initial solid concentration of 10%, 15%, and 20% (w/v), respectively, which was significantly higher than that obtained with a baffled marine impeller. The highest ethanol yield of 83.6%, 73.4%, and 21.8%, based on the theoretical amount of glucose, was obtained with a substrate concentration of 10%, 15%, and 20%, respectively, which also corresponded to 80.5%, 68.6%, and 19.1%, based on the theoretical amount of the cell biomass and soluble glucose present after 48 h of SFF.     

Effect of polyphenol content on the hydrolysis and fermentation of grain sorghum starch

The high polyphenol content of birdproff grain sorghum has been associated with impaired nutritional quality of the grain and with reduced brewing value of birdproof grain sorghum malt due to enzyme inhibition. In this investigation, high polyphenol grain sorghum was evaluated as a feedstock for fermentation ethanol production using NaOH pretreatment to inactivate the polyphenolic compounds prior to hydrolysis with commercial amylases. The polyphenolic inhibition of starch hydrolysis was minimal at a grain sorghum slurry concentration of 20% dry solids, but became pronounced at slurry concentrations of 28% and higher. At these high slurry concentrations the liquefaction and subsequent saccharification and fermentation were markedly improved by alkaline pretreatment. The highest ethanol concentration (12·3%, vol/vol), coupled with the best starch conversion efficiency to ethanol (83·5%), was obtained with a 28% grain sorghum slurry using a partial simultaneous saccharification and fermentation procedure. The residual fermented solids had a crude protein content of 45·4%. Tannic acid decreased yeast cell viability in synthetic media, but had no effect on the hydrolysis or fermentation of grain sorghum starch.     

Ethanol production from cotton-based waste textiles

Ethanol production from cotton linter and waste of blue jeans textiles was investigated. In the best case, alkali pretreatment followed by enzymatic hydrolysis resulted in almost complete conversion of the cotton and jeans to glucose, which was then fermented by Saccharomyces cerevisiae to ethanol. If no pretreatment applied, hydrolyses of the textiles by cellulase and beta-glucosidase for 24 h followed by simultaneous saccharification and fermentation (SSF) in 4 days, resulted in 0.140-0.145 g ethanol/g textiles, which was 25-26% of the corresponding theoretical yield. A pretreatment with concentrated phosphoric acid prior to the hydrolysis improved ethanol production from the textiles up to 66% of the theoretical yield. However, the best results obtained from alkali pretreatment of the materials by NaOH. The alkaline pretreatment of cotton fibers were carried out with 0-20% NaOH at 0 degrees C, 23 degrees C and 100 degrees C, followed by enzymatic hydrolysis up to 4 days. In general, higher concentration of NaOH resulted in a better yield of the hydrolysis, whereas temperature had a reverse effect and better results were obtained at lower temperature. The best conditions for the alkali pretreatment of the cotton were obtained in this study at 12% NaOH and 0 degrees C and 3 h. In this condition, the materials with 3% solid content were enzymatically hydrolyzed at 85.1% of the theoretical yield in 24 h and 99.1% in 4 days. The alkali pretreatment of the waste textiles at these conditions and subsequent SSF resulted in 0.48 g ethanol/g pretreated textiles used.     

Strain improvement of thermotolerant Saccharomyces cerevisiae VS strain for better utilization of lignocellulosic substrates

AIM: Pentose-utilizing yeast development by protoplast fusion and sequential mutations and ethanol fermentation using lignocellulosic substrate. METHODS AND RESULTS: Protoplasts of thermotolerant Saccharomyces cerevisiae and mesophilic, xylose-utilizing Candida shehatae were fused by electrofusion. The fusants were selected based on their growth at 42 degrees C and ability to utilize xylose. The selected best fusant was mutated sequentially and 3 mutant fusants obtained were tested for their stability. The mutant fusant CP11 was found to be stable and used for lignocellulosic fermentation. The Prosopis juliflora wood material was hydrolysed with 1% sulphuric acid initially for 18 h at room temperature and then for 20 min at 121 degrees C. The acid hydrolysate was separated and used for detoxification by ethyl acetate and overliming. The hard cellulosic fraction was hydrolysed with Aspergillus niger crude cellulase enzyme for 18 h at 50 degrees C. The substrate (15% w/v) yielded 84 g l(-1) sugars, representing 80% (w/w) hydrolysis of carbohydrate content present in the lignocellulosic material. The acid and enzyme hydrolysates were then equally mixed and used for fermentation with the developed fusant yeast (CP11). The fusant yeast gave an ethanol yield of 0.459 +/- 0.012 g g(-1), productivity of 0.67 +/- 0.015 g l(-1) h(-1) and fermentation efficiency of 90%. CONCLUSIONS: Protoplast fusion followed by sequential mutations method gave a stable and good performing fusant with maximum utilization of reducing sugars in the media. SIGNIFICANCE AND IMPACT OF THE STUDY: This new method could be applied to develop fusants for better biotechnological applications.     

Effect of temperature on Brettanomyces bruxellensis: metabolic and kinetic aspects

The effect of temperatures ranging from 15 to 35 degrees C on a culture of Brettanomyces bruxellensis was investigated in regards to thermodynamics, metabolism, and kinetics. In this temperature range, we observed an increase in growth and production rates. The growth behavior was well represented using the Arrhenius model, and an apparent activation energy of 16.61 kcal/mol was estimated. A stuck fermentation was observed at 35 degrees C as represented by high cell death. The carbon balance established that temperature had no effect on repartition of the glucose consumption between biomass and products. Hence, the same biomass concentration was obtained for all temperatures, except at 35 degrees C. Moreover, using logistic and Luedeking-Piret models, we demonstrated that production rates of ethanol and acetic acid were partially growth associated. Parameters associated with growth (alpha eth and alpha aa) remained constant with changing temperature, whereas, parameters associated with the population (beta eth and beta aa) varied. Optimal values were obtained at 32 degrees C for ethanol and at 25 degrees C for acetic acid.     

Comparative studies of Feulgen hydrolysis for DNA. I. Influence of different fixatives and polyethylene glycols

We compared the Feulgen hydrolysis curves (37 degrees C, 5 M HCl) of human blood lymphocytes fixed by the following four methods: 96% ethanol, 60 min at 20 degrees C; ethanol-acetone, 1:1, 120 min at 4 degrees C; ethanol-glacial acetic acid mixture (3:1), containing 2% of formaldehyde (EAF), 90 min at 20 degrees C; and ethanol-glacial acetic acid (3:1), 60 min followed by 5% chrome alum solution for 360 min at 20 degrees C. The best results were obtained with EAF-fixation, with respect to the highest amount of DNA-Schiff complex at the peak point of the curve, the longest "plateau" region and the smallest scattering of DNA-Schiff amount values along the "plateau". With other types of fixation the addition of polyethylene glycol (PEG) 6,000 to the hydrolysis solution resulted in modification of the shape of the hydrolysis curve so that it became nearly similar to the EAF-curve. The effect of PEG6000 on the EAF-curve was minimal. Slides fixed by ethanol were used for a comparison of polyethylene glycols with m.w. 1,500, 6,000 and 20,000. The longest "plateau" was obtained with PEG6000. The only effect of PEG1500 was a dramatic increase of DNA-Schiff amount at the peak point. PEG20000 had no significant effect on the shape of the hydrolysis curve. The results are discussed in terms of Kjellstrand's "chain with a stable structure" model of Feulgen hydrolysis.