Liquefaction of lignocellulose at high-solids concentrations

To improve process economics of the lignocellulose to ethanol process a reactor system for enzymatic liquefaction and saccharification at high-solids concentrations was developed. The technology is based on free fall mixing employing a horizontally placed drum with a horizontal rotating shaft mounted with paddlers for mixing. Enzymatic liquefaction and saccharification of pretreated wheat straw was tested with up to 40% (w/w) initial DM. In less than 10 h, the structure of the material was changed from intact straw particles (length 1-5 cm) into a paste/liquid that could be pumped. Tests revealed no significant effect of mixing speed in the range 3.3-11.5 rpm on the glucose conversion after 24 h and ethanol yield after subsequent fermentation for 48 h. Low-power inputs for mixing are therefore possible. Liquefaction and saccharification for 96 h using an enzyme loading of 7 FPU/g.DM and 40% DM resulted in a glucose concentration of 86 g/kg. Experiments conducted at 2%-40% (w/w) initial DM revealed that cellulose and hemicellulose conversion decreased almost linearly with increasing DM. Performing the experiments as simultaneous saccharification and fermentation also revealed a decrease in ethanol yield at increasing initial DM. Saccharomyces cerevisiae was capable of fermenting hydrolysates up to 40% DM. The highest ethanol concentration, 48 g/kg, was obtained using 35% (w/w) DM. Liquefaction of biomass with this reactor system unlocks the possibility of 10% (w/w) ethanol in the fermentation broth in future lignocellulose to ethanol plants.     

Whole slurry fermentation of maleic acid-pretreated oil palm empty fruit bunches for ethanol production not necessitating a detoxification process

The yield of ethanol from oil palm empty fruit bunches (EFB) was increased on exploiting maleic acid pretreatment combined with fermentation of the pretreated whole slurry. The optimized conditions for pretreatment were to expose EFB to a high temperature (190 °C) with 1 % (w/v) maleic acid for a short time duration (3 min ramping to the set temperature with no holding) in a microwave digester. An enzymatic digestibility of 60.9 % (based on theoretical glucose yield) was exhibited using pretreated and washed EFB after 48 h of hydrolysis. Simultaneous saccharification and fermentation (SSF) of the whole slurry of pretreated EFB for 48 h resulted in 61.3 % theoretical yield of ethanol based on the initial amount of glucan in untreated EFB. These results indicate that maleic acid is a suitable catalyst not requiring detoxification steps for whole slurry fermentation of EFB for ethanol production, thus improving the process economics. Also, the whole slurry fermentation can significantly increase the biomass utilization by converting sugar from both solid and liquid phases of the pretreated slurry.     

Optimization of Dilute Acid Pretreatment and Enzymatic Hydrolysis of <Emphasis Type="Italic">Phalaris aquatica</Emphasis> L. Lignocellulosic Biomass in Batch and Fed-Batch Processes

Phalaris aquatica L., a rich in holocellulose (69.80 %) and deficient in lignin (6.70 %) herbaceous, perennial grass species, was utilized in a two-step (biomass pretreatment-enzymatic hydrolysis) saccharification process for sugars recovery. The Taguchi methodology was employed to determine the dilute acid pretreatment and enzymatic hydrolysis conditions that optimized hemicellulose conversion (75.04 %), minimized the production of inhibitory compounds (1.41 g/L), and maximized the cellulose to glucose yield (69.69 %) of mixed particulate biomass (particles <1000 μm) under batch conditions. The effect of biomass particle size on saccharification process efficiency was also investigated. It was found that small-size biomass particles (53–106 μm) resulted in maximum hemicellulose conversion (81.12 %) and cellulose to glucose yield (93.24 %). The determined optimal conditions were then applied to a combined batch pretreatment process followed by a fed-batch enzymatic hydrolysis process that maximized glucose concentration (62.24 g/L) and yield (92.48 %). The overall efficiency of the saccharification process was 88.13 %.     

Acetic acid-catalyzed hydrothermal pretreatment of corn stover for the production of bioethanol at high-solids content

Corn stover (CS) was hydrothermally pretreated using CH₃COOH (0.3 %, v/v), and subsequently its ability to be utilized for conversion to ethanol at high-solids content was investigated. Pretreatment conditions were optimized employing a response surface methodology (RSM) with temperature and duration as independent variables. Pretreated CS underwent a liquefaction/saccharification step at a custom designed free-fall mixer at 50 °C for either 12 or 24 h using an enzyme loading of 9 mg/g dry matter (DM) at 24 % (w/w) DM. Simultaneous enzymatic saccharification and fermentation (SSF) of liquefacted corn stover resulted in high ethanol concentration (up to 36.8 g/L), with liquefaction duration having a negligible effect. The threshold of ethanol concentration of 4 % (w/w), which is required to reduce the cost of ethanol distillation, was surpassed by the addition of extra enzymes at the start up of SSF achieving this way ethanol titer of 41.5 g/L.     

Efficient Acetone–Butanol–Ethanol Production from Corncob with a New Pretreatment Technology—Wet Disk Milling

Acetone–butanol–ethanol (ABE) production from corncob was achieved using an integrated process combining wet disk milling (WDM) pretreatment with enzymatic hydrolysis and fermentation by Clostridium acetobutylicum SE-1. Sugar yields of 71.3 % for glucose and 39.1 % for xylose from pretreated corncob were observed after enzymatic hydrolysis. The relationship between sugar yields and particle size of the pretreated corncob was investigated, suggesting a smaller particle size benefits enzymatic hydrolysis with the WDM pretreatment approach. Analysis of the correlation between parameters representing particle size and efficiency of enzymatic hydrolysis predicted that frequency 90 % is the best parameter representing particle size for the indication of the readiness of the material for enzymatic hydrolysis. ABE production from corncob was carried out with both separate hydrolysis and fermentation (SHF) and simultaneous saccharification and fermentation (SSF) processes using C. acetobutylicum SE-1. Interestingly, when considering the time for fermentation as the time for ABE production, a comparable rate of sugar consumption and ABE production in the SHF process (0.55 g/l·h sugar consumption and 0.20 g/l·h ABE production) could be observed when glucose (0.50 g/l·h sugar consumption and 0.17 g/l·h ABE production) or a mixture of glucose and xylose (0.68 g/l·h sugar consumption and 0.22 g/l·h ABE production) mimicking the corncob hydrolysate was used as the substrate for fermentation. This result suggested that the WDM is a suitable pretreatment method for ABE production from corncob owing to the mild conditions. A higher ABE production rate could be observed with the SSF process (0.15 g/l·h) comparing with SHF process (0.12 g/l·h) when combining the time for saccharification and fermentation and consider it as the time for ABE production. This is possibly a result of low sustained sugar level during fermentation. These investigations lead to the suggestion that this new WDM pretreatment method has the potentials to be exploited for efficient ABE production from corncob.     

Saccharification of orange peel wastes with crude enzymes from new isolated <Emphasis Type="Italic">Aspergillus japonicus</Emphasis> PJ01

This study investigated the saccharification of orange peel wastes with crude enzymes from Aspergillus japonicus PJ01. Pretreated orange peel powder was hydrolyzed by submerged fermentation (SmF) and solid-state fermentation (SSF) crude enzymes, the results showed that 4 % (w/v) of solid loading, undiluted crude enzymes, and 45 °C were suitable saccharification conditions. The hydrolysis kinetics showed that the apparent Michaelis–Menten constant \(K_{{\text{m}_{app} }}\) and maximal reaction rate \(V_{{\max_{app} }}\) were 73.32 g/L and 0.118 g/(L min) for SmF enzyme, and 41.45 g/L and 0.116 g/(L min) for SSF enzyme, respectively. After 48 h of hydrolysis, the saccharification yields were 58.5 and 78.7 %, the reducing sugar concentrations were 14.9 and 20.1 mg/mL by SmF and SSF enzymes. Material balance showed that the SmF enzymatic hydrolysate was enriched galacturonic acid > arabinose > galactose > xylose, and the SSF enzymatic hydrolysate was enriched galacturonic acid > xylose > galactose > arabinose.     

Optimization of pretreatment conditions and use of a two-stage fermentation process for the production of ethanol from seaweed, Saccharina japonica

Saccharina japonica (Sea tangle, Dasima), a seaweed, was fermented in order to produce bioethanol after thermal hydrogen peroxide (H₂O₂) hydrolysis pretreatment and enzymatic saccharification. The optimal pretreatment conditions of 1% (v/v) H₂O₂ (28%, Dustan Pure Chemicals Co., Ltd, Ansan, Korea) and 10% (w/v) seaweed slurry at 121°C for 60 min were determined using the Response Surface Method (RSM). A reducing sugar yield of 33.4% (w/w) and a viscosity of 520 cP were obtained. Enzymatic saccharification was then carried out; a monosaccharide concentration of 28.5 g/L with a 40.5% (w/w) theoretical yield was obtained after the addition of 2-mL Celluclast® 1.5L to 100 g/L of seaweed slurry after thermal H₂O₂ hydrolysis. Fermentation of a two-stage ethanol production was carried out using Saccharomyces cerevisiae KCCM 1129 in order to ferment glucose in the first stage, and a high level of mannitol-acclimated Pichia angophorae KCTC 17574 to ferment mannitol in the second stage. Acclimation of yeast effectively slowed the uptake of sugar in ethanol fermentation. The overall ethanol yield from S. japonica after the two-stage fermentation was 9.9 g/L.     

Characterization of enzymatic saccharification for acid-pretreated lignocellulosic materials with different lignin composition

The enzymatic saccharification of three different feedstocks, rice straw, bagasse and silvergrass, which had been pretreated with different dilute acid concentrations, was studied to verify how enzymatic saccharification was affected by the lignin composition of the raw materials. There was a quantitatively inverse correlation between lignin content and enzymatic digestibility after pretreatment with 1%, 2% and 4% sulfuric acid. The lignin accounted for about 18.8–21.8% of pretreated rice straw, which was less than the 23.1–26.5% of pretreated bagasse and the 21.5–24.1% of pretreated silvergrass. The maximum glucose yield achieved, under an enzyme loading 6.5 FPU g^?1 DM for 72 h, was close to 0.8 g glucose/g glucan from the enzymatic hydrolysis of the pretreated rice straw; this was twice that from bagasse and silvergrass. A decrease in initial rate of glucose production was observed in all cases when the raw materials underwent enzymatic saccharification with 4% sulfuric acid pretreatment. It is suggested that the higher acid concentration led to an inhibition of β-glucosidase activity. Fourier transform infrared (FTIR) spectroscopy further indicated the chemical properties of the rice straw and silvergrass become more hydrophilic after pretreatment using 2% of sulfuric acid, but the pretreated bagasse tended to become more hydrophobic. The hydrophilic nature of the pretreated solid residues may increase the inhibitive effects of lignin on the cellulase and this could become very important for raw materials such as silvergrass that contain more lignin.     

Process development of starch hydrolysis using mixing characteristics of Taylor vortices

In food industries, enzymatic starch hydrolysis is an important process that consists of two steps: gelatinization and saccharification. One of the major difficulties in designing the starch hydrolysis process is the sharp change in its rheological properties. In this study, Taylor–Couette flow reactor was applied to continuous starch hydrolysis process. The concentration of reducing sugar produced via enzymatic hydrolysis was evaluated by varying operational variables: rotational speed of the inner cylinder, axial velocity (reaction time), amount of enzyme, and initial starch content in the slurry. When Taylor vortices were formed in the annular space, efficient hydrolysis occurred because Taylor vortices improved the mixing of gelatinized starch with enzyme. Furthermore, a modified inner cylinder was proposed, and its mixing performance was numerically investigated. The modified inner cylinder showed higher potential for enhanced mixing of gelatinized starch and the enzyme than the conventional cylinder.     

Acetone–butanol–ethanol production from corn stover pretreated by alkaline twin-screw extrusion pretreatment

In this study, the alkaline twin-screw extrusion pretreated corn stover was subjected to enzymatic hydrolysis after washing. The impact of solid loading and enzyme dose on enzymatic hydrolysis was investigated. It was found that 68.2 g/L of total fermentable sugar could be obtained after enzymatic hydrolysis with the solid loading of 10 %, while the highest sugar recovery of 91.07 % was achieved when the solid loading was 2 % with the cellulase dose of 24 FPU/g substrate. Subsequently, the hydrolyzate was fermented by Clostridium acetobutylicum ATCC 824. The acetone–butanol–ethanol (ABE) production of the hydrolyzate was compared with the glucose, xylose and simulated hydrolyzate medium which have the same reducing sugar concentration. It was shown that 7.1 g/L butanol and 11.2 g/L ABE could be produced after 72 h fermentation for the hydrolyzate obtained from enzymatic hydrolysis with 6 % solid loading. This is comparable to the glucose and simulated hydrozate medium, and the overall ABE yield could reach 0.112 g/g raw corn stover.     

Sequential Thermochemical Hydrolysis of Corncobs and Enzymatic Saccharification of the Whole Slurry Followed by Fermentation of Solubilized Sugars to Ethanol with the Ethanologenic Strain <Emphasis Type="Italic">Escherichia coli</Emphasis> MS04

Interest in the use of corncobs as feedstock for bioethanol production is growing. This study assesses the feasibility of sequential thermochemical diluted sulfuric acid pretreatment of corncobs at moderate temperature to hydrolyze the hemicellulosic fraction, followed by enzymatic hydrolysis of the whole slurry, and fermentation of the obtained syrup. The total sugar concentration after enzymatic hydrolysis was 85.21 g/l, i.e., 86 % of the sugars were liberated from the polymeric fractions, together with a low amount of furfural (0.26 g/l) and 4.01 g/l of acetic acid. The syrups, which contained 36.3, 40.9, 4.47, and 1.84 g/l of xylose, glucose, arabinose, and mannose, respectively, were fermented (pH 7, 37 °C, 150 rpm) to ethanol with the metabolically engineered acetate-tolerant Escherichia coli strain MS04 under non-aerated conditions, producing 35 g/l of ethanol in 18 h (1.94 g_EtOH/l/h), i.e., a conversion yield greater than 80 % of the theoretical value based on total sugars was obtained. Hence, using the procedures developed in this study, 288 l of ethanol can be produced per metric ton of dry corncobs. Strain MS04 can ferment sugars in the presence of acetate, and the amount of furans generated during the sequential thermochemical and enzymatic hydrolysis was low; hence, the detoxification step was avoided. The residual salts, acetic acid, and solubilized lignin present in the syrup did not interfere with the production of ethanol by E. coli MS04 and the results show that this strain can metabolize mixtures of glucose and xylose simultaneously.     

Cellulases as an aid to enhance saccharification of cassava root

Summary The conventional saccharification of cassava root by enzymatic hydrolysis is improved by using a little amount of cellulase and cellobiase in addition to conventional enzyme, glucoamylase. With new saccharification[glucoamylase 0.45SGU/g cassava, cellulase 4.5NCU/g cassava, cellobiase 0.09U/g cassava, pH 4.3, temperature 60°C, total volume 465ml : 100g of cassava/400ml of water], the reaction time was reduced by about 5 hours, the concentration of reducing sugar was increased by 40%, glucose production was enhanced by 10% , and the viscosity was reduced by 30%.     

稀碱预处理棕榈残渣制备纤维乙醇

以棕榈残渣(Empty fruit bunch,EFB)为原料,通过预处理、酶解、发酵等过程制备纤维乙醇.首先对比了碱、碱/过氧化氢等预处理条件对棕榈残渣组成及酶解的影响,结果表明稀碱预处理效果较好.适宜的稀碱预处理条件为:NaOH浓度为1％,固液比为1∶10,在40℃浸泡24 h后于121℃下保温30 min,在该条件下,EFB的固体回收率为74.09％,纤维素、半纤维素和木质素的含量分别为44.08％、25.74％和13.89％.对该条件下预处理后的固体样品,以底物浓度5％、酶载量30 FPU/g底物酶解72 h,纤维素和半纤维素的酶解率分别达到84.44％和89.28％.进一步考察了酶载量和底物浓度对酶解的影响以及乙醇批式同步糖化发酵,当酶载量为30 FPU/g底物,底物浓度由5％增加至25％时,利用酿酒酵母Saccharomyces cerevisiae(接种量为5％,VIV)发酵72 h后乙醇的浓度分别为9.76 g/L和35.25 g/L,可分别达到理论得率的79.09％和56.96％.     

High-solid enzymatic hydrolysis and fermentation of solka floc into ethanol

To lower the cost of ethanol distillation of fermentation broths, a high initial glucose concentration is desired. However, an increase in the substrate concentration typically reduces the ethanol yield because of insufficient mass and heat transfer. In addition, different operating temperatures are required to optimize the enzymatic hydrolysis (50 degrees ) and fermentation (30 degrees ). Thus, to overcome these incompatible temperatures, saccharification followed by fermentation (SFF) was employed with relatively high solid concentrations (10% to 20%) using a portion loading method. In this study, glucose and ethanol were produced from Solka Floc, which was first digested by enzymes at 50 degrees for 48 h, followed by fermentation. In this process, commercial enzymes were used in combination with a recombinant strain of Zymomonas mobilis (39679:pZB4L). The effects of the substrate concentration (10% to 20%, w/v) and reactor configuration were also investigated. In the first step, the enzyme reaction was achieved using 20 FPU/g cellulose at 50 degrees for 96 h. The fermentation was then performed at 30 degrees for 96 h. The enzymatic digestibility was 50.7%, 38.4%, and 29.4% after 96 h with a baffled Rushton impeller and initial solid concentration of 10%, 15%, and 20% (w/v), respectively, which was significantly higher than that obtained with a baffled marine impeller. The highest ethanol yield of 83.6%, 73.4%, and 21.8%, based on the theoretical amount of glucose, was obtained with a substrate concentration of 10%, 15%, and 20%, respectively, which also corresponded to 80.5%, 68.6%, and 19.1%, based on the theoretical amount of the cell biomass and soluble glucose present after 48 h of SFF.     

Production of bio-fuel ethanol from distilled grain waste eluted from Chinese spirit making process

Distilled grain waste eluted from Chinese spirit making is rich in carbohydrates, and could potentially serve as feedstock for the production of bio-fuel ethanol. Our study evaluated two types of saccharification methods that convert distilled grain waste to monosaccharides: enzymatic saccharification and concentrated H₂SO₄ saccharification. Results showed that enzymatic saccharification performed unsatisfactorily because of inefficient removal of lignin during pretreatment. Concentrated H₂SO₄ saccharification led to a total sugar recovery efficiency of 79.0 %, and to considerably higher sugar concentrations than enzymatic saccharification. The process of ethanol production from distilled grain waste based on concentrated H₂SO₄ saccharification was then studied. The process mainly consisted of concentrated H₂SO₄ saccharification, solid–liquid separation, decoloration, sugar–acid separation, oligosaccharide hydrolysis, and continuous ethanol fermentation. An improved simulated moving bed system was employed to separate sugars from acid after concentrated H₂SO₄ saccharification, by which 95.8 % of glucose and 85.8 % of xylose went into the sugar-rich fraction, while 83.3 % of H₂SO₄ went into the acid-rich fraction. A flocculating yeast strain, Saccharomyces cerevisiae KF-7, was used for continuous ethanol fermentation, which produced an ethanol yield of 91.9–98.9 %, based on glucose concentration.     

Enhanced Bioethanol Production from Blue Agave Bagasse in a Combined Extrusion–Saccharification Process

This paper describes an improved process for bioethanol production using a recently developed combined extrusion–saccharification technology. Blue agave bagasse (BAB) was pretreated via a thermo-mechano-chemical process (co-rotational twin-screw, reactive extrusion) to increase the availability of cellulose and hemicellulose for enzymatic saccharification. Then, several commercial enzyme preparations, boosted with accessory enzymes (exoglucanase, endoglucanase, hemicellulase, xylanase, and β-glucosidase), were tested with extruded BAB at 5 % consistency in a stirred vessel. The enzyme blend that produced the highest saccharification yield was evaluated at different BAB consistencies. The obtained concentration of sugars increased up to 69.5 g/L (73 % yield) when a 20 % BAB mixture was used. When the enzyme blend was fed into the extruder and with a residence time of 2 min, the yield reached 15 % of the maximum theoretical of C6 sugars along this step. This extruded and pre-saccharified BAB was further hydrolyzed and used for fermentation. The pre-saccharification step significantly enhanced cellulose degradation and ethanol production. Our results indicate that the enzymatic saccharification of BAB, coupled with reactive extrusion, produces an excellent substrate for bioethanol production.     

Process Modeling of Enzymatic Hydrolysis of Wet-Exploded Corn Stover

The aim of this work was to investigate the optimal process conditions leading to high glucose yield (over 80 %) after wet explosion (WEx) pretreatment and enzymatic hydrolysis. The study focused on determining the “sweet spot” where the glucose yield obtained is optimized compared to the cost of the enzymes. WEx pretreatment was conducted at different temperatures, times, and oxygen concentrations to determine the best WEx pretreatment conditions for the most efficient enzymatic hydrolysis. Enzymatic hydrolysis was further optimized at the optimal conditions using central composite design of response surface methodology with respect to two variables: Cellic® CTec2 loading [5 to 40 mg enzyme protein (EP)/g glucan] and substrate concentration (SC) (5 to 20 %) at 50 °C for 72 h. The most efficient and economic conditions for corn stover conversion to glucose were obtained when wet-exploded at 170 °C for 20 min with 5.5 bar oxygen followed by enzymatic hydrolysis at 20 % SC and 15 mg EP/g glucan (5 filter paper units) resulting in a glucose yield of 84 %.     

Enhanced enzymatic hydrolysis of mild alkali pre-treated rice straw at high-solid loadings using in-house cellulases in a bench scale system

In the present study, scale-up systems for cellulase production and enzymatic hydrolysis of pre-treated rice straw at high-solid loadings were designed, fabricated and tested in the laboratory. Cellulase production was carried out using tray fermentation at 45 °C by Aspergillus terreus in a temperature-controlled humidity chamber. Enzymatic hydrolysis studies were performed in a horizontal rotary drum reactor at 50 °C with 25 % (w/v) solid loading and 9 FPU g^?1 substrate enzyme load using in-house as well commercial cellulases. Highly concentrated fermentable sugars up to 20 % were obtained at 40 h with an increased saccharification efficiency of 76 % compared to laboratory findings (69.2 %). These findings demonstrate that we developed a simple and less energy intensive bench scale system for efficient high-solid saccharification. External supplementation of commercial β-glucosidase and hemicellulase ensured better hydrolysis and further increased the saccharification efficiency by 14.5 and 20 %, respectively. An attempt was also made to recover cellulolytic enzymes using ultrafiltration module and nearly 79–84 % of the cellulases and more than 90 % of the sugars were recovered from the saccharification mixture.     

Optimization of Enzymatic Hydrolysis of Steam Pretreated Triticale Straw

Efficient conversion of the carbohydrates into fermentable sugars is crucial for industrial implementation of 2G biofuels such as bioethanol. The main objective of this study was to improve the enzymatic hydrolysis of steam pretreated triticale straw (slurry, pressed-slurry or water insoluble solids (WIS)) by optimal combination of cellulase (Cellic® CTec2) and hemicellulase (Cellic® HTec2) and incubation period for a target glucan conversion of 80 %. Among the three substrates evaluated, pressed-slurry and WIS resulted in similar sugar yields but WIS presented lower enzyme requirements. Different combinations of cellulase and endo-xylanase could provide an 80 % of glucan conversion depending on the weight assigned to constrain. The selected enzyme combination, 0.1 mL Cellic®CTec2/g WIS and 0.2 mL Cellic®HTec2/g WIS, could achieve a glucan conversion of 80 % in 45 h (desirability of 0.9). Doubling the enzyme dosage could further improve the saccharification productivity by reducing the incubation period to 37 h. The optimisation of enzymatic hydrolysis of lignocellulosic substrates, to reduce the cost of sugars production, is a compromise between substrate, enzyme dosage, incubation time and the benchmark yield, although a more favourable response can be generated with an optimised combination of enzymes.     

Steam pretreatment of H(2)SO(4)-impregnated Salix for the production of bioethanol

In the bioconversion of lignocellulosic materials to ethanol, pretreatment of the material prior to enzymatic hydrolysis is essential to obtain high overall yields of sugar and ethanol. In this study, steam pretreatment of fast-growing Salix impregnated with sulfuric acid has been investigated by varying the temperature (180-210 degrees C), the residence time (4, 8 or 12 min), and the acid concentration (0.25% or 0.5% (w/w) H(2)SO(4)). High sugar recoveries were obtained after pretreatment, and the highest yields of glucose and xylose after the subsequent enzymatic hydrolysis step were 92% and 86% of the theoretical, respectively, based on the glucan and xylan contents of the raw material. The most favorable pretreatment conditions regarding the overall sugar yield were 200 degrees C for either 4 or 8 min using 0.5% sulfuric acid, both resulting in a total of 55.6g glucose and xylose per 100g dry raw material. Simultaneous saccharification and fermentation experiments were performed on the pretreated slurries at an initial water-insoluble content of 5%, using ordinary baker's yeast. An overall theoretical ethanol yield of 79%, based on the glucan and mannan content in the raw material, was obtained.