The influence of ferrous sulfate utilization on the sugar yields from dilute-acid pretreatment of softwood for bioethanol production

By employing metal salts in dilute-acid pretreatment the severity can be reduced due to reduced activation energy. This study reports on a dilute-acid steam pretreatment of spruce chips by addition of a small amount of ferrous sulfate to the acid catalyst, i.e., either SO₂, H₂SO₃ or H₂SO₄. The utilization of ferrous sulfate resulted in a slightly increased overall glucose yield (from 74% to 78% of the theoretical value) in pretreatment with SO₂ and H₂SO₃. Impregnation with ferrous sulfate and sulfuric acid did not give any improvement compared with pretreatment based solely on H₂SO₄.     

Fractionation of wheat and barley straw to access high-molecular-mass hemicelluloses prior to ethanol production

The cost efficiency of the biorefining process can be improved by extracting high-molecular-mass hemicelluloses from lignocellulosic biomass prior to ethanol production. These hemicelluloses can be used in several high-value-added applications and are likely to be important raw materials in the future. In this study, steam pretreatment in an alkaline environment was used to pretreat the lignocellulosic biomass for ethanol production and, at the same time, extract arabinoxylan with a high-molecular-mass. It was shown that 30% of the arabinoxylan in barley straw could be extracted with high-molecular-mass, without dissolving the cellulose. The cellulose in the solid fraction could then be hydrolysed with cellulase enzymes giving a cellulose conversion of about 80–90% after 72 h. For wheat straw, more than 40% of the arabinoxylan could be extracted with high-molecular-mass and the cellulose conversion of the solid residue after 72 h was about 70–85%. The high cellulose conversion of the pretreated wheat and barley straw shows that they can be used for ethanol production without further treatment. It is therefore concluded that it is possible to extract high-molecular-mass arabinoxylan simultaneously with the pretreatment of biomass for ethanol production in a single steam pretreatment step.     

Ultrasound pretreatment of cassava chip slurry to enhance sugar release for subsequent ethanol production

The use of ultrasound pretreatment to enhance liquefaction and saccharification of cassava chips was investigated. Cassava chip slurry samples were subjected to sonication for 10-40 s at three power levels of low (2 W/mL), medium (5 W/mL), and high (8 W/mL). The samples were simultaneously exposed to enzymes to convert starch into glucose. The cassava particle size declined nearly 40-fold following ultrasonic pretreatment at high power input. Scanning electron micrographs of both unsonicated (control) and sonicated samples showed disruption of fibrous material in cassava chips but did not affect the granular structure of starch. Reducing sugar release improved in direct proportion to the power input and sonication time. The reducing sugar increase was as much as 180% with respect to the control groups. The slurry samples with enzyme addition during sonication resulted in better reducing sugar release than the samples with enzyme addition after sonication. The heat generated during sonication below starch gelatinization temperature apparently had no effect on the reducing sugar release. The reducing sugar yield and energy efficiency of ultrasound pretreated samples increased with total solids (TS) contents. The highest reducing sugar yield of 22 g/100 g of sample and efficiency of 323% were obtained for cassava slurry with 25% TS at high power. The reducing sugar yield at the completion of reaction (R(infinity)) were over twofold higher compared to the control groups. The integration of ultrasound into a cassava-based ethanol plant may significantly improve the overall ethanol yield.     

Enhanced enzymatic hydrolysis of rapeseed straw by popping pretreatment for bioethanol production

The objective of this study was to find a pretreatment process that enhances enzymatic conversion of biomass to sugars. Rapeseed straw was pretreated by two processes: a wet process involving wet milling plus a popping treatment, and a dry process involving popping plus dry milling. The effects of the pretreatments were studied both in terms of structural and compositional changes and change in susceptibility to enzymatic hydrolysis. After application of the wet and dry processes, the amounts of cellulose and xylose in the straw were 37-38% and 14-15%, respectively, compared to 31% and 12% in untreated counterparts. In enzymatic hydrolysis performance, the wet process presented the best glucose yield, with a 93.1% conversion, while the dry process yielded 69.6%, and the un-pretreated process yielded <20%. Electron microscopic studies of the straw also showed a relative increase in susceptibility to enzymatic hydrolysis with pretreatment.     

Process and technoeconomic analysis of leading pretreatment technologies for lignocellulosic ethanol production using switchgrass

Six biomass pretreatment processes to convert switchgrass to fermentable sugars and ultimately to cellulosic ethanol are compared on a consistent basis in this technoeconomic analysis. The six pretreatment processes are ammonia fiber expansion (AFEX), dilute acid (DA), lime, liquid hot water (LHW), soaking in aqueous ammonia (SAA), and sulfur dioxide-impregnated steam explosion (SO(2)). Each pretreatment process is modeled in the framework of an existing biochemical design model so that systematic variations of process-related changes are consistently captured. The pretreatment area process design and simulation are based on the research data generated within the Biomass Refining Consortium for Applied Fundamentals and Innovation (CAFI) 3 project. Overall ethanol production, total capital investment, and minimum ethanol selling price (MESP) are reported along with selected sensitivity analysis. The results show limited differentiation between the projected economic performances of the pretreatment options, except for processes that exhibit significantly lower monomer sugar and resulting ethanol yields.     

Effect of washing on yield in one- and two-step steam pretreatment of softwood for production of ethanol

Two-step steam pretreatment of softwood on laboratory scale has previously been shown to result in higher yields than one-step steam pretreatment. In this study, these results are verified on a larger scale. In an industrial process filtration and washing of the material between the two pretreatment steps are difficult without release of pressure. A worst case without filtration or washing was thus investigated to determine the influence of poor washing on the yield of sugars and the formation of byproducts. Steam pretreatment with SO(2) impregnation was investigated using three different procedures. One-step steam pretreatment was performed at 215 degrees C for 5 min. Two different kinds of two-step steam pretreatment were performed at 190 degrees C for 2 min in the first step and at 210 degrees C for 5 min in the second step. In one case the slurry obtained after the first pretreatment step was separated into a liquid and a solid phase, where the water-insoluble solid material was washed with water and then used for pretreatment in the second step. In the other case of two-step steam pretreatment, neither separation nor washing was performed. The pretreated material was evaluated using both enzymatic hydrolysis and fed-batch simultaneous saccharification and fermentation. Both two-step steam pretreatment process configurations investigated resulted in higher yields of ethanol (300 L/ton) than one-step steam pretreatment (227 L/ton). Separation and washing of the material between the pretreatment steps in the two-step steam pretreatment process did not improve the overall sugar yield, although the formation of sugar degradation products was reduced.     

Effect of initial moisture content and chip size on the bioconversion efficiency of softwood lignocellulosics

Previous optimization strategies for the bioconversion of lignocellulosics by steam explosion technologies have focused on the effects of temperature, pH, and treatment time, but have not accounted for changes in severity brought about by properties inherent in the starting feedstock. Consequently, this study evaluated the effects of chip properties, feedstock size (40-mesh, 1.5 x 1.5 cm, 5 x 5 cm), and moisture content (12% and 30%) on the overall bioconversion process, and more specifically on the efficacy of removal of recalcitrant lignin from the lignocellulosic substrates following steam explosion. Increasing chip size resulted in an improvement in the solids recovery, with concurrent increases in the water soluble, hemicellulose-derived sugar recovery (7.5%). This increased recovery is a result of a decrease in the "relative severity" of the pretreatment as chip size increases. Additionally, the decreased relative severity minimized the condensation of the recalcitrant residual lignin and therefore increased the efficacy of peroxide fractionation, where a 60% improvement in lignin removal was possible with chips of larger initial size. Similarly, increased initial moisture content reduced the relative severity of the pretreatment, generating improved solids and hemicellulose-derived carbohydrate recovery. Both increased chip size and higher initial moisture content results in a substrate that performs better during peroxide delignification, and consequently enzymatic hydrolysis. Furthermore, a post steam-explosion refining step increased hemicellulose-derived sugar recovery and was most effectively delignified (to as low as 6.5%). The refined substrate could be enzymatically hydrolyzed to very high levels (98%) and relatively fast rates (1.23 g/L/h).     

Organosolv pretreatment of lignocellulosic biomass for enzymatic hydrolysis

Production of ethanol by bioconversion of lignocellulosic biomass has attracted much interest in recent years. However, the pretreatment process for increasing the enzymatic digestibility of cellulose has become a key step in commercialized production of cellulosic ethanol. During the last decades, many pretreatment processes have been developed for decreasing the biomass recalcitrance, but only a few of them seem to be promising. From the point of view for integrated utilization of lignocellulosic biomass, organosolv pretreatment provides a pathway for biorefining of biomass. This review presents the progress of organosolv pretreatment of lignocellulosic biomass in recent decades, especially on alcohol, organic acid, organic peracid and acetone pretreatments, and corresponding action mechanisms. Evaluation and prospect of organosolv pretreatment were performed. Finally, some recommendations for future investigation of this pretreatment method were given.     

白腐菌协同热水预处理对毛白杨化学组分和酶水解效果的影响

【目的】增强真菌预处理的效率和降低热水预处理对反应条件的要求。【方法】综合利用白腐菌和热水预处理毛白杨,分析此方法对毛白杨化学组分和酶水解效果的影响。【结果】白腐菌Lenzites betulinus C5617协同热水处理,损失率最高达70.70%。纤维素在2个预处理阶段都有损失,其中L.betulinus C5617达到29.62%。木质素的降解主要集中在白腐菌预处理阶段,其中L.betulinus C5617降解的酸不溶木素较多,达到了16.98%。综合预处理显著改善了毛白杨的酶水解效果。与只经热水预处理的样品相比较,L.betulinus C5617和P.sanguineus D9497协同热水处理分别引起还原糖得率上升了20.60%和12.23%。【结论】综合预处理降低了热水解对反应条件的要求,节约了预处理成本。     

Supercritical carbon dioxide pretreatment of corn stover and switchgrass for lignocellulosic ethanol production

Supercritical CO₂ (SC-CO₂), a green solvent suitable for a mobile lignocellulosic biomass processor, was used to pretreat corn stover and switchgrass at various temperatures and pressures. The CO₂ pressure was released as quickly as possible by opening a quick release valve during the pretreatment. The biomass was hydrolyzed after pretreatment using cellulase combined with β-glucosidase. The hydrolysate was analyzed for the amount of glucose released. Glucose yields from corn stover samples pretreated with SC-CO₂ were higher than the untreated sample’s 12% glucose yield (12 g/100 g dry biomass) and the highest glucose yield of 30% was achieved with SC-CO₂ pretreatment at 3500 psi and 150 °C for 60 min. The pretreatment method showed very limited improvement (14% vs. 12%) in glucose yield for switchgrass. X-ray diffraction results indicated no change in crystallinity of the SC-CO₂ treated corn stover when compared to the untreated, while SEM images showed an increase in surface area.     

Dilute acid pretreatment, enzymatic saccharification and fermentation of wheat straw to ethanol

Wheat straw consists of 48.57 ± 0.30% cellulose and 27.70 ± 0.12% hemicellulose on dry solid (DS) basis and has the potential to serve as a low cost feedstock for production of ethanol. Dilute acid pretreatment at varied temperature and enzymatic saccharification were evaluated for conversion of wheat straw cellulose and hemicellulose to monomeric sugars. The maximum yield of monomeric sugars from wheat straw (7.83%, w/v, DS) by dilute H₂SO₄ (0.75%, v/v) pretreatment and enzymatic saccharification (45 °C, pH 5.0, 72 h) using cellulase, β-glucosidase, xylanase and esterase was 565 ± 10 mg/g. Under this condition, no measurable quantities of furfural and hydroxymethyl furfural were produced. The yield of ethanol (per litre) from acid pretreated enzyme saccharified wheat straw (78.3 g) hydrolyzate by recombinant Escherichia coli strain FBR5 was 19 ± 1 g with a yield of 0.24 g/g DS. Detoxification of the acid and enzyme treated wheat straw hydrolyzate by overliming reduced the fermentation time from 118 to 39 h in the case of separate hydrolysis and fermentation (35 °C, pH 6.5), and increased the ethanol yield from 13 ± 2 to 17 ± 0 g/l and decreased the fermentation time from 136 to 112 h in the case of simultaneous saccharification and fermentation (35 °C, pH 6.0).     

Enhancement of ethanol and biogas production from high‐crystalline cellulose by different modes of NMO pretreatment

Pretreatment of high‐crystalline cellulose with N‐methyl‐morpholine‐N‐oxide (NMO or NMMO) to improve bioethanol and biogas production was investigated. The pretreatments were performed at 90 and 120°C for 0.5–15 h in three different modes, including dissolution (85% NMO), ballooning (79% NMO), and swelling (73% NMO). The pretreated materials were then enzymatically hydrolyzed and fermented to ethanol or anaerobically digested to biogas (methane). The pretreatment at 85% NMO, 120°C and 2.5 h resulted in 100% yield in the subsequent enzymatic hydrolysis and around 150% improvement in the yield of ethanol compared to the untreated and water‐treated material. However, the best results of biogas production were obtained when the cellulose was treated with swelling and ballooning mode, which gave almost complete digestion in 15 days. Thus, the pretreatment resulted in 460 g ethanol or 415 L methane from each kg of cellulose. Analysis of the structure of treated and untreated celluloses showed that the dissolution mode can efficiently convert the crystalline cellulose I to cellulose II. However, it decreases the water swelling capacity of the cellulose. On the other hand, swelling and ballooning modes in NMO treatment were less efficient in both water swelling capacity and cellulose crystallinity. No cellulose loss, ambient pressure, relatively moderate conditions, and high efficiency make the NMO a good alternative for pretreatment of high‐crystalline cellulosic materials. Biotechnol. Bioeng. 2010; 105: 469–476. © 2009 Wiley Periodicals, Inc.     

Enhanced enzymatic saccharification of kenaf powder after ultrasonic pretreatment in ionic liquids at room temperature

This study demonstrates for the first time that the enzymatic hydrolysis of cellulose is drastically enhanced following ultrasonic pretreatment of lignocellulosic material in ionic liquids (ILs) when compared to conventional thermal pretreatment. Five types of ILs, 1-buthyl-3-methylimidazolium chloride (BmimCl), 1-allyl-3-methylimidazolium chloride (AmimCl), 1-ethyl-3-methylimidazolium chloride (EmimCl), 1-ethyl-3-methylimidazolium diethyl phosphate (EmimDep), and 1-ethyl-3-methylimidazolium acetate (EmimOAc) were tested. Cellulose saccharification ratio was about 20% for kenaf powders pretreated in BmimCl, AmimCl, EmimCl, and EmimDep by conventional heating at 110 °C for 120 min. Conversely, 60-95% of cellulose was hydrolyzed to glucose, subsequent to ultrasonic pretreatment in the same ILs for 120 min at 25 °C. The cellulose saccharification ratio of kenaf powder in EmimOAc was 86% after only 15 min of the ultrasonic pretreatment at 25 °C, compared to only 47% in that case of thermal pretreatment in the IL.     

Comparisons of SPORL and dilute acid pretreatments for sugar and ethanol productions from aspen

This study reports comparative evaluations of sugar and ethanol production from a native aspen (Populus tremuloides) between sulfite pretreatment to overcome recalcitrance of lignocellulose (SPORL) and dilute acid (DA) pretreatments. All aqueous pretreatments were carried out in a laboratory wood pulping digester using wood chips at 170°C with a liquid to oven dry (od) wood ratio (L/W) of 3:1 at two levels of acid charge on wood of 0.56 and 1.11%. Sodium bisulfite charge on od wood was 0 for DA and 1.5 or 3.0% for SPORL. All substrates produced by both pretreatments (except DA with pretreatment duration of 0) had good enzymatic digestibility of over 80%. However, SPORL produced higher enzymatic digestibility than its corresponding DA pretreatment for all the experiments conducted. As a result, SPORL produced higher ethanol yield from simultaneous saccharification and fermentation of cellulosic substrate than its corresponding DA pretreatment. SPORL was more effective than its corresponding DA pretreatment in reducing energy consumption for postpretreatment wood chip size-reduction. SPORL, with lower energy input and higher sugar and ethanol yield, produced higher sugar and ethanol production energy efficiencies than the corresponding DA pretreatment.     

Effect of particle size on the rate of enzymatic hydrolysis of cellulose

The effect of particle size on enzymatic hydrolysis of cellulose has been investigated. The average size of microcrystalline cotton cellulose has been reduced to submicron scale by using a media mill. The milled products were further subjected to hydrolysis using cellulase. High cellulose concentration (7%) appeared to retard the size reduction and resulted in greater particles and smaller specific surface areas than those at low concentration (3%) with the same milling time. Initial rate method was employed to explore the rate of enzymatic hydrolysis of cellulose. The production rate of cellobiose was increased at least 5-folds due to the size reduction. The yield of glucose was also significantly increased depending upon the ratio of enzyme to substrate. A high glucose yield (60%) was obtained in 10-h hydrolysis when the average particle size was in submicron scale.     

Comparative sugar recovery and fermentation data following pretreatment of poplar wood by leading technologies

Through a Biomass Refining Consortium for Applied Fundamentals and Innovation among Auburn University, Dartmouth College, Michigan State University, the National Renewable Energy Laboratory, Purdue University, Texas A&M University, the University of British Columbia, and the University of California at Riverside, leading pretreatment technologies based on ammonia fiber expansion, aqueous ammonia recycle, dilute sulfuric acid, lime, neutral pH, and sulfur dioxide were applied to a single source of poplar wood, and the remaining solids from each technology were hydrolyzed to sugars using the same enzymes. Identical analytical methods and a consistent material balance methodology were employed to develop comparative performance data for each combination of pretreatment and enzymes. Overall, compared to data with corn stover employed previously, the results showed that poplar was more recalcitrant to conversion to sugars and that sugar yields from the combined operations of pretreatment and enzymatic hydrolysis varied more among pretreatments. However, application of more severe pretreatment conditions gave good yields from sulfur dioxide and lime, and a recombinant yeast strain fermented the mixed stream of glucose and xylose sugars released by enzymatic hydrolysis of water washed solids from all pretreatments to ethanol with similarly high yields. An Agricultural and Industrial Advisory Board followed progress and helped steer the research to meet scientific and commercial needs. © 2009 American Institute of Chemical Engineers Biotechnol. Prog., 2009     

Hydrothermal processing and enzymatic hydrolysis of sorghum bagasse for fermentable carbohydrates production

Untreated and hydrothermally treated sorghum bagasse (SB) was hydrolyzed to simple sugars by the synergistic action of cellulases and hemicellulases produced by the fungi Fusarium oxysporum and Neurospora crassa. Synergism between the two lignocellulolytic systems was maximized with the application of higher fraction of N. crassa enzymes.Hydrothermolysis of SB was studied at a wide range of treatment times and temperatures. At intense pretreatment conditions (210 °C for 20 min; logR₀ = 4.54), the residual hemicellulose percentage was 17.45%, while formation of inhibitory products, 5-hydromethyl-furfural (HMF), furfural, acetic and formic acid, (0.21, 0.51, 3.36 and 1.80 g/l, respectively) remained in acceptable levels.Maximum conversion of cellulose and total polysaccharides of the untreated SB were 23.18% and 18.79%, respectively. Combining hydrothermal treatment and enzymatic hydrolysis of released oligosaccharides and insoluble solids resulted in improvement of cellulose (approximately 15% increase) and total polysaccharides (two fold) hydrolysis compared to that of untreated SB.     

Improved one‐step steam pretreatment of SO2‐Impregnated softwood with time‐dependent temperature profile for ethanol production

In the production of ethanol from lignocellulosic material, pretreatment of the raw material before enzymatic hydrolysis and fermentation is essential to obtain high overall yields of sugar and ethanol. Two‐step steam pretreatment results in higher ethanol yields from softwood than the standard one‐step pretreatment process. However, the difficulty with separation and washing of the material at high pressure between the two pretreatment steps is a major drawback. In this study, a new one‐step pretreatment procedure was investigated, in which the time‐temperature profile was varied during pretreatment. The efficiency of pretreatment was assessed by performing simultaneous saccharification and fermentation on the pretreated slurries. Pretreatment of SO₂‐impregnated softwood performed by varying the temperature (190–226°C), the residence time (5–10 min), and the mode of temperature increase (linear or stepwise), resulted in recovery of about 90% of the mannose and glucose present in the raw material. The highest ethanol yield, 75% of theoretical based on the glucan and mannan content of the raw material, was obtained at pretreatment conditions of 190°C for 12 min. Similar ethanol yields were achieved when running the pretreatment as one‐step (190–200°C), two levels of temperature, at shorter residence time (7 min), which results in lower capital costs for the process. © 2010 American Institute of Chemical Engineers Biotechnol. Prog., 2010     

Process considerations and economic evaluation of two-step steam pretreatment for production of fuel ethanol from softwood

To increase the overall ethanol yield from softwood, the steam pretreatment stage can be carried out in two steps. The two-step pretreatment process was evaluated from a techno-economic standpoint and compared with the one-step pretreatment process. The production plants considered were designed to utilize spruce as raw material and have a capacity of 200,000 tons/year. The two-step process resulted in a higher ethanol yield and a lower requirement for enzymes. However, the two-step process is more capital-intensive and has a higher energy requirement. The estimated ethanol production cost was the same, 4.13 SEK/L (55.1 cent /L) for both alternatives. For the two-step process different energy-saving options were considered, such as a higher concentration of water-insoluble solids in the filter cake before the second step, and the possibility of excluding the pressure reduction between the steps. The most optimistic configuration, with 50% water-insoluble solids in the filter cake in the feed to the second pretreatment step, no pressure reduction between the pretreatment steps, and 77% overall ethanol yield (0.25 kg EtOH/kg dry wood), resulted in a production cost of 3.90 SEK/L (52.0 cent /L). This shows the potential for the two-step pretreatment process, which, however, remains to be verified in pilot trials.     

Organosolv pretreatment by crude glycerol from oleochemicals industry for enzymatic hydrolysis of wheat straw

In order to defray the cost of biodiesel production, the ensuing work was to further investigate utilization of the crude glycerol (CG) from oleochemicals industry in the atmospheric autocatalytic organosolv pretreatment (AAOP) to enhance enzymatic hydrolysis.

The AAOP–CG enabled wheat straw to achieve with reasonable enzymatic hydrolysis yields, reaching 75% for the wet substrate and 63% for the dried. Lipophilic compounds from the CG formed pitch deposition on the fiber, which was responsible for low delignification (30%) and also troublesome in practical operation. Pitch deposits itself had no significant role on enzymatic hydrolysis. A striking finding of the lignin recondensation and/or lignin–carbohydrate complex helped explain why dried pretreated wheat straw had a low enzymatic hydrolysis yield. The CG was suitable for the AAOP to enhance enzymatic hydrolysis of lignocellulosic biomass. But it was advisable to remove lipophilic compounds from crude glycerol before utilization.