Use of Biocides as Agents against Microorganism-Induced Corrosion Increases Ecological Safety

Five synergistic combinations of biocides have been identified, of which kathon plus copper sulfate is the most efficient against Serratia marcescens. Depending on the ratio of the biocides, the active concentrations needed to maintain the synergistic effect can be decreased 4- to 20-fold. Combinations of biocides with salts promoting steel passivation (such as carbonates and phosphates) have been developed, which are more potent in decreasing corrosion-induced losses of mild steel than biocides and salts taken in isolation. Biocides should be introduced into systems susceptible to biocorrosion at the start of their exploitation, otherwise higher concentrations or synergistic compositions have to be used.     

The use of biocides to control sulphate‐reducing bacteria in biofilms on mild steel surfaces

Three different types of biocides, viz. formaldehyde (FM), glutaraldehyde (GA) and isothiozolone (ITZ) were used to control planktonic and sessile populations of two marine isolates of sulphate‐reducing bacteria (SRB). The influence of these biocides on the initial attachment of cells to mild steel surfaces, on subsequent biofilm formation and on the activity of hydrogenase enzymes within developed biofilms was evaluated. In the presence of biocides the rate and degree of colonization of mild steel by SRB depended on incubation time, bacterial isolate and the type of biocide used. Although SRB differed in their susceptibility to biocides, for all isolates the biofilm population was more resistant to the treatment than the planktonic population. GA showed highest efficiency in controlling planktonic and sessile SRB compared with the other two biocides. The activity of the enzyme hydrogenase measured in SRB biofilms varied between isolates and with the biocide treatment. No correlation was found between the number of sessile cells and hydrogenase activity.     

A green biocide enhancer for the treatment of sulfate-reducing bacteria (SRB) biofilms on carbon steel surfaces using glutaraldehyde

Generally speaking, a much higher concentration of biocide is needed to treat biofilms compared to the dosage used to for planktonic bacteria. With increasing restrictions of environmental regulations and safety concerns on large-scale biocide uses such as oil field applications, it is highly desirable to make more effective use of biocides. In this paper a green biocide enhancer ethylenediaminedisuccinate (EDDS) that is a biodegradable chelator, was found to enhance the efficacy of glutaraldehyde in its treatment of sulfate-reducing bacteria (SRB) biofilms. Experiments were carried out in 100 ml anaerobic vials with carbon steel coupons. The ATCC 14563 strain of Desulfovibrio desulfuricans was used. Biofilms on coupon surfaces were visualized using scanning electron microscopy (SEM). Experimental results showed that EDDS reduced the glutaraldehyde dosages considerably in the inhibition of SRB biofilm establishment and the treatment of established biofilms on carbon steel coupon surfaces.     

Non-toxic antifouling activity of polymeric 3-alkylpyridinium salts from the Mediterranean sponge Reniera sarai (Pulitzer-Finali)

The antifouling activity and toxicity of polymeric 3-alkylpyridinium salts (poly-APS) isolated from the Mediterranean sponge Reniera sarai were studied. The activity of these natural products was compared to that of zinc and copper complexes of pyrithione, two non-persistent booster biocides successfully used in current antifouling coatings. Larvae of Balanus amphitrite (cyprids and nauplii) were used to monitor settlement inhibition and the extent to which inhibition was due to toxicity. The microalga Tetraselmis suecica and larvae of the mussel Mytilus galloprovincialis were used in toxicity bioassays. Compared to the booster biocides, poly-APS were less effective at inhibiting cyprid settlement, but their effects were non toxic and reversible, with very low toxicity against the organisms used in the toxicity bioassays. Although encouraging, these results are not enough to warrant the use of poly-APS as a potential commercial antifoulant. They however justify possible future efforts to chemically synthesize poly-APS analogues for further tests.     

Synergistic inhibition of microbial sulfide production by combinations of the metabolic inhibitor nitrite and biocides

MICs of six broad-spectrum biocides and two specific metabolic inhibitors and fractional inhibitory concentration indexes (FICIs) for controlling a sulfide-producing consortium were determined. Nitrite was synergistic (FICI<1) with all but one biocide due to its specific inhibition of dissimilatory sulfite reductase. Hence, combining nitrite with biocides allows more efficient and cost-effective control of sulfate-reducing bacteria.     

Synergistic Inhibition of Microbial Sulfide Production by Combinations of the Metabolic Inhibitor Nitrite and Biocides

MICs of six broad-spectrum biocides and two specific metabolic inhibitors and fractional inhibitory concentration indexes (FICIs) for controlling a sulfide-producing consortium were determined. Nitrite was synergistic (FICI < 1) with all but one biocide due to its specific inhibition of dissimilatory sulfite reductase. Hence, combining nitrite with biocides allows more efficient and cost-effective control of sulfate-reducing bacteria.     

Effects of polarization in the presence and absence of biocides on biofilms in a simulated paper machine water

The antifouling potential of electric polarization combined and not combined with biocides was studied in nonsaline warm water with high organic content. Deinococcus geothermalis is a bacterium known for forming colored biofilms in paper machines and for its persistence against cleaning and chemical treatments. When D. geothermalis biofilms grown for 24 h in simulated paper machine water were exposed to cathodic or cathodically weighted pulsed polarization at least 60% (P < 0.05) of the biofilms were removed from stainless steel (AISI 316L). Biofilm removal by 25 ppm (effective substances 5-25 ppm) of oxidizing biocides (bromochloro-5,5-dimethylhydantoin, 2,2-dibromo-2-cyanoacetamide, peracetic acid) increased to 70% when combined with cathodically weighted pulsed polarization. Using a novel instrument that allows real-time detection of reactive oxygen species (ROS) we showed that the polarization program effective in antifouling generated ROS in a pulsed manner on the steel surface. We thus suggest that the observed added value of oxidative biocides combined with polarization depended on ROS. This suggestion was supported by the finding that a reductive biocide, methylene bisthiocyanate, counteracted the antifouling effect of polarization.     

Evaluation of the antifouling properties of 3-alyklpyridine compounds

One of the most promising alternative technologies to antifouling (AF) biocides based on toxic heavy metals lies in the development of natural eco-friendly biocides. The present study evaluates the AF potential of structurally different compounds containing a 3-alkylpyridine moiety. The products, namely poly 3-alkylpyridinium salts, saraine, and haminols, were either extracted or derived from natural sources (the sponges Haliclona sp. and Reniera sarai and the mollusc Haminoea fusari), or obtained by chemical synthesis. All the molecules tested showed generally good anti-settlement activity against larvae of the barnacle Amphibalanus (=Balanus) amphitrite (EC(50) values between 0.19 and 3.61 μg ml(-1) and low toxicity (LC(50) values ranging from 2.04 to over 100 μg ml(-1)) with non-target organisms. For the first time, the AF potential of a synthetic monomeric 3-alkylpyridine was demonstrated, suggesting that chemical synthesis is as a realistic way to produce large amounts of these compounds for future research and development of environmentally-friendly AF biocides.     

From Broad-Spectrum Biocides to Quorum Sensing Disruptors and Mussel Repellents: Antifouling Profile of Alkyl Triphenylphosphonium Salts

‘Onium’ compounds, including ammonium and phosphonium salts, have been employed as antiseptics and disinfectants. These cationic biocides have been incorporated into multiple materials, principally to avoid bacterial attachment. In this work, we selected 20 alkyl-triphenylphosphonium salts, differing mainly in the length and functionalization of their alkyl chains, in fulfilment of two main objectives: 1) to provide a comprehensive evaluation of the antifouling profile of these molecules with relevant marine fouling organisms; and 2) to shed new light on their potential applications, beyond their classic use as broad-spectrum biocides. In this regard, we demonstrate for the first time that these compounds are also able to act as non-toxic quorum sensing disruptors in two different bacterial models (Chromobacterium violaceum and Vibrio harveyi) as well as repellents in the mussel Mytilus galloprovincialis. In addition, their inhibitory activity on a fouling-relevant enzymatic model (tyrosinase) is characterized. An analysis of the structure-activity relationships of these compounds for antifouling purposes is provided, which may result useful in the design of targeted antifouling solutions with these molecules. Altogether, the findings reported herein provide a different perspective on the biological activities of phosphonium compounds that is particularly focused on, but, as the reader will realize, is not limited to their use as antifouling agents.     

Combined Effects of Radiation and Inorganic Reagents during Irradiation on Radiosensitivity of Bacterial Cells

The combined effects of inorganic reagents and radiation on the inactivation of E. coli in the resting state were studied. Among these reagents halides such as NaCI, KCI, KBr and KI were found to have a considerable synergistic action to radiation. Temperature effect on the halide action during irradiation was not observed, but removal of oxygen from halide solutions increased the radiosensitivity of cells. Combined effects of radiation and some other inorganic reagents were also investigated. Heavy metal salts and hydrogen peroxide were synergistic, nitrates and sulfates having no influence or a slightly protective action. Barium chloride and calcium chloride were protective in lower concentrations and synergistic in higher concentrations. These synergistic actions of inorganic reagents except ferric salts were observed during irradiation, but not after the irradiation.     

Changes in the strength of attachment of micro-organisms to surfaces following treatment with disinfectants and cleansing agents

Suspensions of Pseudomonas aeruginosa and Staphylococcus epidermidis , and biofilms established (16 h) on submerged glass and stainless steel (216 2B) coupons, were exposed to sodium hypochlorite (0·02% or 0·015% w/v), Dodigen (0·0015% w/v or 0·0006% w/v), sodium dodecylsulphate (6% w/v or 0·1% w/v) and Tween-80 (6% w/v) for 5 min at 20 °C. Survival was assessed by viable counts and blot succession. Biofilm bacteria were significantly less susceptible to these biocides than were planktonic cells, but their attachment to the surfaces was loosened by such treatments. Treatment with the non-ionic surfactant, Tween-80, however, strengthened the attachment of Staph. epidermidis to stainless steel. Such effects on attachment strength, which are species and surface dependent, have profound implications on post-treatment cleansing and possible re-contamination of product in clean-in-place (CIP) systems.     

The effects of disinfectant foam on microbial biofilms

This investigation examined the effects of common aqueous biocides and disinfectant foams derived from them on Pseudomonas aeruginosa biofilms. Biofilms were grown on stainless steel coupons under standardised conditions in a reactor supplemented with low concentrations of organic matter to simulate conditions prevalent in industrial systems. Five-day-old biofilms formed under ambient conditions with continuous agitation demonstrated a low coefficient of variation (5.809%) amongst viable biofilm bacteria from independent trials. Scanning electron microscopy revealed biofilms on coupons with viable biofilm bacteria observed by confocal microscopy. An aqueous solution of a common foaming agent amine oxide (AO) produced negligible effects on bacterial viability in biofilms (p>0.05). However, significant biofilm inactivation was noted with aqueous solutions of common biocides (peracetic acid, sodium hypochlorite, sodium ethylenediaminetetraacetic acid) with or without AO (p<0.05). Aereation of a mixture of AO with each of these common biocides resulted in significant reductions in the viability of biofilm bacteria (p<0.05). In contrast, limited effects were noted by foam devoid of biocides. A relationship between microbial inactivation and the concentration of biocide in foam (ranging from 0.1-0.5%) and exposure period were noted (p<0.05). Although, lower numbers of viable biofilm bacteria were recovered after treatment with the disinfectant foam than by the cognate aqueous biocide, significant differences between these treatments were not evident (p>0.05). In summary, the studies revealed significant biofilm inactivation by biocidal foam prepared with common biocides. Validation of foam disinfectants in controlled trials at manufacturing sites may facilitate developments for clean in place applications. Advantages of foam disinfectants include reductions in the volumes of biocides for industrial disinfection and in their disposal after use.     

A novel approach to mode of action of cationic biocides morphological effect on antibacterial activity

A. KANAZAWA, T. IKEDA AND T. ENDO. 1995 A new concept for the mode of action of cationic biocides is proposed in which the antibacterial activity of cationic disinfectants is ascribed essentially to molecular organizations of cations within aggregates, i.e. the activity is determined by the size of aggregates and number of active molecules comprising the aggregate. On the basis of the new concept, the morphological effect of disinfectants in aqueous solution on the antibacterial activity is discussed for low molecular weight phosphonium salts with single and double long alkyl chains (carbon number 14). The proposed new concept can be applied to all phenomena reported previously in antibacterial activity of cationic biocides and this concept is very important from the viewpoint of molecular design of more active cationic biocides.     

Evaluation of the antifouling properties of 3-alyklpyridine compounds

One of the most promising alternative technologies to antifouling (AF) biocides based on toxic heavy metals lies in the development of natural eco-friendly biocides. The present study evaluates the AF potential of structurally different compounds containing a 3-alkylpyridine moiety. The products, namely poly 3-alkylpyridinium salts, saraine, and haminols, were either extracted or derived from natural sources (the sponges Haliclona sp. and Reniera sarai and the mollusc Haminoea fusari), or obtained by chemical synthesis. All the molecules tested showed generally good anti-settlement activity against larvae of the barnacle Amphibalanus (=Balanus) amphitrite (EC₅₀ values between 0.19 and 3.61?μg?ml^?1) and low toxicity (LC₅₀ values ranging from 2.04 to over 100?μg?ml^?1) with non-target organisms. For the first time, the AF potential of a synthetic monomeric 3-alkylpyridine was demonstrated, suggesting that chemical synthesis is as a realistic way to produce large amounts of these compounds for future research and development of environmentally-friendly AF biocides.     

Evaluation of a model biofilm for the ranking of biocide performance against sulphate-reducing bacteria

A model artificial biofilm was developed and evaluated for ranking the performance of biocides for application in oil production pipelines. The biofilm consisted of an alginate gel matrix into which were incorporated bacteria, scrapings from the inner surfaces of oil production pipelines and some crude oil.
The viability and sulphide-respiration rates of sulphate-reducing bacteria (SRB) within freshly-prepared artificial biofilm remained largely unchanged during a 2-week storage period. Furthermore, storage of the model biofilm did not alter the susceptibility of the incorporated SRB to a biocide. These findings showed that artificial biofilm may be produced in advance of a biocide assessment study and stored for at least 2 weeks over the course of the study without the model system undergoing changes which affected the relative performance of the biocides assessed. Artificial biofilms were found to be more resistant to biocides than planktonic bacteria and the addition of oil pipeline scrapings and crude oil to the artificial biofilm was found to increase further the resistance of biofilm to biocides.     

Adaptation of Campylobacter jejuni to biocides used in the food industry affects biofilm structure,adhesion strength,and cross-resistance to clinical antimicrobial compounds

The emergence of biocide-adapted Campylobacter jejuni strains that developed into biofilms and their potential to develop clinical resistance to antimicrobial compounds was studied. C. jejuni was grown in sub-lethal concentrations of five biocides used in the food industry. C. jejuni exhibited adaptation to these biocides with increased minimum inhibitory concentrations. The 3-D structures of the biofilms produced by the biocide-adapted cells were investigated by atomic force microscopy (AFM). The results revealed marked variability in biofilm architecture, including ice-crystal-like structures. Adaptation to the biocides enhanced biofilm formation, with significant increases in biovolume, surface coverage, roughness, and the surface adhesion force of the biofilms. Adaptation to commercial biocides induced resistance to kanamycin and streptomycin. This study suggests that the inappropriate use of biocides may lead to cells being exposed to them at sub-lethal concentrations, which can result in adaptation of the pathogens to the biocides and a subsequent risk to public health.     

Ammonia as an attractive component of host odour for the yellow fever mosquito, Aedes aegypti

Behavioural responses of Aedes aegypti mosquitoes to ammonia were investigated in a modified Y-tube olfactometer. Ammonia was attractive in concentrations from 17 ppb to 17 ppm in air when presented together with lactic acid. Aqueous solutions of ammonia salts in concentrations comparable to those found in human sweat also increased the attractiveness of lactic acid. The role of lactic acid as an essential synergist for ammonia became further apparent by the fact that ammonia alone or in combination with carbon dioxide was not effective, even though the synergistic effect of carbon dioxide and lactic acid was corroborated. An extract from human skin residues, which attracts approximately 80% of the tested mosquitoes, contains both lactic acid and ammonia. The combination of these compounds, however, attracts no more than 45%, indicating that other components on human skin also play a role in host finding. Preparative liquid chromatography of the skin extract yielded three behaviourally active fractions which work together synergistically. Fraction III contains lactic acid as the effective principle; the compositions of the other two have not been clarified yet. The attractiveness of fraction I was augmented considerably when ammonia was added, whereas the effect of fraction II was not influenced by ammonia. These results suggests that ammonia is part of the effective principle of fraction II and contributes to the attractive effect of host odours.     

Evaluation of antifungal properties of octyl gallate and its synergy with cinnamaldehyde

The objective of this study was to investigate the possibility of using octyl gallate alone or with organic biocides as a preservative against wood decay fungi. Antifungal activities of three antioxidants, propyl gallate, octyl gallate and butylated hydroxyltoluene (BHT) were tested against four wood decay fungi, Lenzites betulina, Trametes versicolor, Gloeophyllum trabeum and Laetiporus sulphureus. Octyl gallate was found to be the only active compound with IC50 values of 0.47, 0.16, 0.24 and 0.04 mM against L. betulina, T. versicolor, G. trabeum and L. sulphureus, respectively. A synergistic effect was also found when octyl gallate was combined with cinnamaldehyde. Results obtained herein demonstrated that octyl gallate by itself exhibited an excellent antifungal property and enhanced protection was further observed by combining it with cinnamaldehyde.     

Adaptation of amoebae to cooling tower biocides

Adaptation of amoebae to four cooling tower Biocides, which included a thiocarbamate compound, tributyltin neodecanoate mixed with quaternary ammonium compounds (TBT/QAC), another QAC alone, and an isothiazolin derivative, was studied. Previously we found that amoebae isolated from waters of cooling towers were more resistant to cooling tower biocides than amoebae from other habitats. Acanthamoeba hatchetti and Cochliopodium bilimbosum, obtained from American Type Culture Collection and used in the previous studies, were tested to determine whether they could adapt to cooling tower Biocides. A. hatchetti was preexposed to subinhibitory concentrations of the four Biocides for 72h, after which they were tested for their resistance to the same and other biocides. C. bilimbosum was exposed to only two biocides, as exposure to the other two was lethal after 72 h. Preexposure to the subinhibitory concentrations of the Biocides increased the resistance of the amoebae, as indicated by a significant increase in the minimum inhibitory concentration (up to 30-fold). In addition, cross-resistance was also observed, i.e., exposure to one biocide caused resistance to other biocides. These results show that amoebae can adapt to biocides in a short time. The phenomenon of cross-resistance indicates that regularly alternating biocides, as is done to control microbial growth in cooling towers, may not be effective in keeping amoeba populations in check. On the contrary, exposure to one biocide may boost the amoebae's resistance to a second biocide before the second biocide is used in the cooling tower. Since amoebae may harbor Legionella, or alone cause human diseases, these results may be important in designing effective strategies for controlling pathogens in cooling towers. Correspondence to: S.G. Berk.     

Biofilm formation and biocide susceptibility testing of Mycobacterium fortuitum and Mycobacterium marinum

The ability of non-tuberculous mycobacteria to form biofilms may allow for their increased resistance to currently used biocides in medical and industrial settings. This study examines the biofilm growth of Mycobacterium fortuitum and Mycobacterium marinum, using the MBEC trade mark assay system, and compares the susceptibility of planktonic and biofilm cells to commercially available biocides. With scanning electron microscopy, both M. fortuitum and M. marinum form biofilms that are morphologically distinct. Biocide susceptibility testing suggested that M. fortuitum biofilms displayed increased resistance over their planktonic state. This is contrasted with M. marinum biofilms, which were generally as or more susceptible over their planktonic state.