Crystallinity and morphology in films of starch, amylose and amylopectin blends

Films of potato starch, amylose, and amylopectin and blends thereof were prepared by solution casting and examined using X-ray diffraction, light microscopy, transmission electron microscopy, and differential scanning calorimetry. Amylose films had a relative crystallinity of about 30% whereas amylopectin films were entirely amorphous. Blending of amylose and amylopectin resulted in films with a considerably higher degree of crystallinity than could be predicted. This is explained by cocrystallization between amylose and amylopectin and possibly by crystallization of amylopectin. The crystallized material gave rise to an endotherm detected with differential scanning calorimetry. The enthalpy and peak temperature of the transition also increased as the water content decreased. When the amylose proportion in the blends was low, separate phases of amylose and amylopectin were observed by light microscopy. At higher amylose proportions, however, the phase separation was apparently prevented by amylose gelation and the formation of a continuous amylose network. The amylose network in the films, observed with transmission electron microscopy, consisted of stiff strands and open pores and became less visible as the amylose proportion decreased. The water content of the films was dependent on the microstructure and the crystallinity.     

Solid state NMR studies on the structural and conformational properties of natural maize starches

Natural maize starches having a range of amylose contents have been characterised by CP/MAS NMR spectroscopy. Chemical shifts, relative resonance intensities, line-widths and spectral shapes were compared at different moisture contents. At 10% moisture content, these parameters showed few significant differences across a range of apparent amylose levels from 0 to 84%. After hydration of the granules to ≈30% moisture, it was found that the amylose content significantly affected the relative signal intensities and line-widths especially of C-1 and C-4 resonances. Narrower line-widths after hydration were attributed to (i) an increased degree of crystallinity, and (ii) disappearance of the signals of amorphous material which, on becoming more mobile, became invisible to the CP/MAS experiment. The enhanced resolution at higher moisture levels revealed signals which were assigned to the amylose–lipid complex, i.e. V-type amylose. The amount of V-amylose detected by NMR increased with both amylose content and lipid content of the granule. Prolonged treatment of the granules with iodine vapour significantly increased the amount of V-type amylose in the high amylose samples, but caused a decrease in their degree of crystallinity. Waxy-maize starch was barely affected by iodination. The results provide evidence that amylose tends to disrupt the structural order within amylopectin crystallities. This effect is enhanced by the formation of the amylose–iodine complex, indicating that V-amylose could be a major crystallite-disrupting agent in native starch granules.     

Physicochemical properties and in vitro digestibility of flour and starch from pea (Pisum sativum L.) cultivars

Flours and isolated starches from three different cultivars (1544-8, 1658-11 and 1760-8) of pea grown under identical environmental conditions were evaluated for their physicochemical properties and in vitro digestibility. The protein content, total starch content and apparent amylose content of pea flour ranged from 24.4 to 26.3%, 48.8 to 50.2%, and 13.9 to 16.7%, respectively. In pea starches, the 1760-8 showed higher apparent amylose content and total starch content than the other cultivars. Pea starch granules were irregularly shaped, ranging from oval to round with a smooth surface. All pea starches showed C-type X-ray diffraction pattern with relative crystallinity ranging between 23.7 and 24.7%. Pea starch had only a single endothermic transition (12.1-14.2 J/g) in the DSC thermogram, whereas pea flour showed two separate endothermic transitions corresponding to starch gelatinization (4.54-4.71 J/g) and disruption of the amylose-lipid complex (0.36-0.78 J/g). In pea cultivars, the 1760-8 had significantly higher setback and final viscosity than the other cultivars in both pea flour (672 and 1170 cP, respectively) and isolated starch (2901 and 4811 cP). The average branch chain length of pea starches ranged from 20.1 to 20.3. The 1760-8 displayed a larger proportion of short branch chains, DP (degree of polymerization) 6-12 (21.1%), and a smaller proportion of long branch chains, DP ≥ 37 (8.4%). The RDS, SDS and RS contents of pea flour ranged from 23.7 to 24.1%, 11.3 to 12.8%, and 13.2 to 14.8%, respectively. In pea starches, the 1760-8 showed a lower RDS content but higher SDS and RS contents. The expected glycemic index (eGI), based on the hydrolysis index, ranged from 36.9 to 37.7 and 69.8 to 70.7 for pea flour and isolated pea starch, respectively.     

Physicochemical properties and structure of large, medium and small granule starches in fractions of normal barley endosperm

Normal barley grain was milled to flour with a machine used to polish brewers' rice from the surface layer to the center. Large (18.4 microm, median size), medium (12.3 microm) and small (2.2 microm) granule starches were isolated from classified flours. Their physicochemical properties and fine structure were investigated. The percentage (w%) of large granules decreased from the surface layer to the center, while the amounts of medium and small granules increased. Although all the starch granules were an A-type crystal, the relative crystallinity varied from 22.0 to 27.4%. The DPn of the amyloses was around 1600 and similar for all the samples. But the amylose content of the starches varied from 21.9 to 26.4%. Also, the amylopectins showed differences in DPn (around 5700-7900) and chain-length distribution between granule size or fractions. The transition temperature ranges and the enthalpy values of the starch granules differed with granule size. The gelatinization properties showed no correlation with any of the parameters, except the enthalpy value and relative crystallinity (gamma = +0.73). The findings suggested that the structural characteristics of the starches in classified flours of normal barley differed essentially from those of waxy barley.     

The granular structure of C-type pea starch and its role in gelatinization

We have used a combination of techniques to study the structure and properties of C-type starch from pea seeds. It was found that all C-type starch granules contain both types of polymorph; the B polymorphs are in the center of the granule and are surrounded by the A polymorphs. During heating in excess salt solution the A and B polymorphs within C-type granules melt independently, giving a double transition in heat capacity and a two-step swelling, compared with single transitions for A- and B-type starches. It was shown that B polymorphs gave a transition with a lower peak temperature than A. The disruption of crystallinity during gelatinization began from the hilum area and was propagated along the granule, accompanied by swelling of disrupted areas. It is proposed that the swelling of disrupted parts of the granule decreases the melting temperature of the neighboring crystallites resulting in the progressive disruption of crystalline areas. The gelatinization process is dependent on the arrangement of A and B polymorphs within the granule. © 1998 John Wiley & Sons, Inc. Biopoly 45: 323–332, 1998     

Structural studies of starches with different water contents

The proportion of double helices in starches from a series of pea [rb, rug4-b, rug3-a, and lam-c mutants, and the wild type (WT) parental line], potato and maize (normal and low amylose), and wheat (normal) lines, ranged from about 30-50% on a dry weight basis. In relatively dry starch powders, only about half of the double helices were in crystalline order, this proportion being higher for A-type than for B-type starches. Using starch from WT pea as an example, it was found that increasing water content results in an increase in total crystallinity. When the water content was raised to a level similar to that in excess water, the proportion of crystallinity was close to the proportion of double helices (DH). Measuring crystallinity in starches with a high water content is difficult using traditional methods such as x-ray diffraction. A method was developed, therefore, for determining starch structural characteristics in excess water by measuring the enthalpy of gelatinization transition in quasi-equilibrium differential scanning calorimetry (DSC) experiments. It is suggested that DH% = DeltaH(sp)/DeltaH(DH) x 100%, where DeltaH(sp) and DeltaH(DH) represent the specific enthalpies of gelatinisation transition, DeltaH(sp) being measured as J/g dry starch weight and DeltaH(DH) as J/g DH, in starch. Studies on potato and maize starches in excess water and in 0.6M KCl showed, respectively, that DeltaH(DH) was 36.3 and 35.6 J/g for B-type polymorphs and 33.0 and 35.0 J/g for A-type polymorphs. For C-type starches, such as those from pea, intermediate values of DeltaH(DH), related to the proportions A-/B-polymorphs, should be used. The type of crystallinity in starch can be determined by the shift in peak temperature for thermograms in excess water and in excess 0.6M KCl. For B-polymorphs this shift was found to be approximately 2-3 degrees C and for A-polymorphs approximately 7-12 degrees C. The ratio between ordered areas with both A- and B-polymorphs can be determined from the enthalpies of disruption of each area. These enthalpies can be obtained by deconvolution of bimodal thermograms produced by C-type starches in excess 0.6M KCl. This methodical approach can be applied to all starches that give a sharp gelatinisation thermogram in excess water. Using a range of methods, including DSC, it was found that starch granules from the mutant peas are constructed in a similar way to those from the WT, with B-polymorphs in the centre and A-polymorphs at the periphery of all granules. The proportion of A/B-polymorphs, however, differed between the mutants. It was found that in addition to increasing the total crystallinity, increasing the water content within the granules also resulted in an increase in the proportion of B-polymorphs.     

Amylose synthesized in vitro by amylosucrase: morphology, structure, and properties

The recombinant amylosucrase from Neisseria polysaccharea was used to synthesize in vitro amylose from sucrose as unique substrate. The morphology and structure of the insoluble residue were shown to depend only on the initial sucrose concentration (100, 300, or 600 mM), which controlled both the chain length and concentration at the precipitation stage. The average degree of polymerization (DP) in the precipitated product varied from 58 for the lowest initial sucrose concentration (100 mM) to 45 and 35 for higher sucrose concentrations (300 and 600 mM, respectively). The shorter chains (DP 35 and 45), produced in high yields (54 and 24 g/L respectively), precipitated as polycrystalline aggregates with exceptional crystallinity, without optimization of the reaction medium for crystallization. The longer chains (DP 58), produced in lower amount (2.9 g/L), formed networks similar to those observed for amylose gels. All synthesized products displayed a B-type crystal structure. Their melting behavior was also studied, the thermostability being higher for the precipitate containing the longer chains. Further thermal treatments were shown to still improve the crystallinity and yield substrates usable as new standards for the determination of the relative crystallinity of starchy products. The kinetics of chain elongation and aggregation were thoroughly investigated in order to explain how the action of amylosucrase resulted in such different amylose structures. These results emphasize the potentiality of amylosucrase in the design of amylodextrins with controlled morphology, structure, and physicochemical properties.     

Structure of lintnerized starch is related to X-ray diffraction pattern and susceptibility to acid and enzyme hydrolysis of starch granules

Acid-resistant residues (lintnerized starches, Ls) were prepared from starches showing A-, B- and C- X-ray diffraction patterns. Ls retained the same X-ray crystalline type as their native counterparts with an improvement in diffraction intensity. Fluorophore-assisted capillary electrophoresis (FACE) study indicated that structural characteristics of Ls were associated with X-ray diffraction patterns. Double helices originated from linear chains with an approximate average degree of polymerisation (DP) 14, 16, and 15 would span the entire length of crystalline lamellae of A-, B-, and C-type starches, respectively. The proportion of singly branched materials (SB) with DP 25 protected in Ls was higher for A-type Ls (10-17%) than for B-type Ls (4-6%) and C-type Ls (8%). The structures of SB were similar in which branched chain (DP 13-15) was longer than main chain (DP 10-12). The structural characteristics of Ls are discussed in relation to acid and enzymatic degradations of starch granules.     

粉末X射线衍射图谱计算植物淀粉结晶度方法的探讨

植物淀粉有A-型、B-型和C-型3种晶体。以水稻(Oryza sativa)、马铃薯(Solanum tuberosum)、豌豆(Pisum sativum) 和莲藕(Nelumbo nucifera)淀粉为材料, 利用粉末X-射线衍射仪(XRD)调查了不同晶体类型淀粉的波谱特征, 探讨XRD波谱相对结晶度的计算方法。软件峰拟合法、软件曲线法、直线作图法和曲线作图法均可用于计算淀粉XRD波谱的相对结晶度, 以曲线作图法计算结果较为可靠。利用曲线作图法得出的结果表明, 稻米淀粉的结晶度与直链淀粉含量呈显著线性负相关, 酸解莲藕淀粉的结晶度与淀粉酸水解度呈显著线性正相关。酸水解使莲藕淀粉的C-型晶体转变为A-型晶体。上述研究结果为利用XRD分析植物淀粉晶体类型和计算相对结晶度提供了重要参考。     

Effects of acid hydrolysis and defatting on crystallinity and pasting properties of freeze-thawed high amylose corn starch

Paste of defatted and/or mildly acid-hydrolyzed high amylose corn starch was freeze-thawed, and then the starch was isolated by vacuum drying for the analysis in crystallization and pasting properties. X-ray diffraction pattern and differential scanning calorimetric analysis showed that the crystallinity of the freeze-thawed starch was increased as the degree of hydrolysis increased. The diffraction pattern revealed B- and V-crystals with patterns with diffraction peaks at 17, 20, and 23–25° (2θ), which were developed by amylose recrystallization during the freeze-thawing. The crystal melting enthalpies, for dual endothermic transitions above 100 °C, which resulted from the melting of amylose–lipids complex and amylose double helices were raised by the treatment. The isolated and dried starch formed a paste by aqueous heating under the ambient pressure, and its paste viscogram exhibited substantially higher resistance to shear-thinning, and rapid setback upon cooling. Acid hydrolysis, however, reduced overall paste viscosity, possibly due to the increased crystallinity. Enzyme-resistant starch content in the acid hydrolyzed starch was increased by the freeze-thawing, but not by acid hydrolysis. It was slightly increased by defatting.     

Physico-chemical characterisation of sago starch

The physico-chemical characteristics of various sago starch samples from South East Asia were determined and compared to starches from other sources. X-ray diffraction studies showed that all the sago starches exhibited a C-type diffraction pattern. Scanning electron microscopy showed that they consist of oval granules with an average diameter around 30 μm. Proximate composition studies showed that the moisture content in the sago samples varied between 10.6% and 20.0%, ash between 0.06% and 0.43%, crude fat between 0.10% and 0.13%, fiber between 0.26% and 0.32% and crude protein between 0.19% and 0.25%. The amylose content varied between 24% and 31%. The percentage of amylose obtained by colourimetric determination agreed well with the values obtained by fractionation procedures and potentiometric titration. Intrinsic viscosities and weight average molecular weight were determined in 1M KOH. Intrinsic viscosity for amylose from sago starches varied between 310 and 460 ml/g while for amylopectin the values varied between 210 and 250 ml/g. The molecular weight for amylose was found to be in the range of 1.41×10⁶ to 2.23×10⁶ while for amylopectin it was in the range of 6.70×10⁶ to 9.23×10⁶. The gelatinisation temperature for the sago starches studied varied between 69.4°C and 70.1°C. The exponent ‘a’ in the Mark–Houwink equation and the exponent ‘’ in the equation R_g=kM was found to be 0.80 and 0.58, respectively for amylose separated from sago starch and these are indicative of a random coil conformation. Two types of pasting properties were observed. The first was characterised by a maximum consistency immediately followed by sharp decrease in consistency while the second type was characterised by a plateau when the maximum consistency was reached.     

Effect of heat–moisture treatment on the structure and physicochemical properties of tuber and root starches

Starch from tubers potato (Solanum tuberosum), taro (Alocassia indica), new cocoyam (Xanthosoma sagitifolium), true yam (Dioscorea alata), and root cassava, (Manihot esculenta) crops was isolated and its morphology, composition and physicochemical properties were investigated before and after heat–moisture treatment (HMT) (100 °C, for 10 h at a moisture content of 30%). Native starch granules were round to oval to polygonal with smooth surfaces. The granule size (diameter) ranged from 3.0 to 110 μm.The total amylose content ranged from 22.4 to 29.3%, of which 10.1–15.5% was complexed by native lipid. The phosphorus content ranged from 0.01 to 0.1%. The X-ray pattern of potato and true yam was of the ‘B’-type. Whereas, that of new cocoyam and taro was of the ‘A’-type. Cassava exhibited a mixed ‘A+B’-type X-ray pattern. The relative crystallinity, swelling factor (SF), amylose leaching (AML), gelatinization temperature range and the enthalpy of gelatinization of the native starches ranged from 30 to 46, 22 to 54, 5 to 23%, 13 to 19 °C and 12 to 18 J/g, respectively. Susceptibility of native starches towards hydrolysis by 2.2N HCl and porcine pancreatic -amylase were 60–86% (after 12 days), and 4–62% (after 72 h), respectively. Retrogradation was most pronounced in the B-type starches. Granule morphology remained unchanged after HMT. The X-ray pattern of the B-type starches was altered (B→A+B) on HMT. However, that of the other starches remained unchanged. HMT decreased SF, AML, gelatinization enthalpy and susceptibility towards acid hydrolysis, but increased gelatinization temperatures and enzyme susceptibility. Extent of retrogradation and relative crystallinity decreased on HMT of true yam and potato starches, but remained unchanged in the other starches. The foregoing data showed that changes in physicochemical properties on HMT are influenced by the interplay of crystallite disruption, starch chain associations and disruption of double helices in the amorphous regions.     

Amylosucrase‐mediated β‐carotene encapsulation in amylose microparticles

The β‐carotene embedded amylose microparticles (BC‐AmMPs) were prepared in one‐step by utilizing the unique catalytic activity of amylosucrase from Deinococcus geothermalis (DgAS), which synthesizes linear amylose chains using sucrose as the sole substrate. Synthesized amylose chains self‐assembled with β‐carotene to form well‐defined spherical microparticles with an encapsulation yield of 65%. The BC‐AmMPs produced (average diameter ～8 µm) were bright orange due to the embedded β‐carotene, and this was confirmed by Raman analysis. XRD showed BC‐AmMPs had a B‐type amylose crystal structure with a degree of crystallinity lower than that of AmMPs. This lower crystallinity of AmMP after BC encapsulation was confirmed by DSC analysis. Decreased enthalpy of gelatinization (ΔH_gel) of BC‐AmMP implied that molecular order within the amylose microstructure was influenced by the presence of BC. The stability of BC against environmental stresses, such as UV light and oxidative stress, was significantly enhanced by its encapsulation. The authors propose a new approach to the preparation of an amylose based carrier system for active compounds or expensive food ingredients with poor stabilities during storage or processing. Given that amylose is a safe food material, the devised encapsulation system will find wide range of practical applications in the food industry. © 2017 American Institute of Chemical Engineers Biotechnol. Prog., 33:1640–1646, 2017     

The effects of amylose content on the molecular size of amylose, and on the distribution of amylopectin chain length in maize starches

The amylose to amylopectin ratios in six maize starch samples of differing amylose contents were measured by enzymatic debranching, followed by high performance size exclusion chromatography (HPSEC). The molecular size of amyloses, estimated by -log K_wav, shows progressive decrease with the increase in amylose content in maize starches. The gel permeation chromatographs of the corresponding amylopectins, debranched with isoamylase, showed bimodal distributions containing long and short chains. The average chain length of amylopectin has a correlation with amylose content. The correlation coefficients between amylose content and average chain length, long chain length, weight ratio and the mole ratio of long and short chain length, were 0.97, 0.92, 0.96, 0.94 respectively. The maize starch with the highest amylose content has the lowest amylose molecular size and the longest chains, with a high ratio of long to short chains in its amylopectin fraction. Comparing the values of amylose content determined by HPSEC of starch or debranched starch with those of the iodinecomplex method, we conclude that long chains of amylopectin in high amylose starches contribute significantly to apparent amylose content.     

Effects of starch synthase IIa gene dosage on grain, protein and starch in endosperm of wheat

Starch synthases (SS) are responsible for elongating the alpha-1,4 glucan chains of starch. A doubled haploid population was generated by crossing a line of wheat, which lacks functional ssIIa genes on each genome (abd), and an Australian wheat cultivar, Sunco, with wild type ssIIa alleles on each genome (ABD). Evidence has been presented previously indicating that the SGP-1 (starch granule protein-1) proteins present in the starch granule in wheat are products of the ssIIa genes. Analysis of 100 progeny lines demonstrated co-segregation of the ssIIa alleles from the three genomes with the SGP-1 proteins, providing further evidence that the SGP-1 proteins are the products of the ssIIa genes. From the progeny lines, 40 doubled haploid lines representing the eight possible genotypes for SSIIa (ABD, aBD, AbD, ABd, abD, aBd, Abd, abd) were characterized for their grain weight, protein content, total starch content and starch properties. For some properties (chain length distribution, pasting properties, swelling power, and gelatinization properties), a progressive change was observed across the four classes of genotypes (wild type, single nulls, double nulls and triple nulls). However, for other grain properties (seed weight and protein content) and starch properties (total starch content, granule morphology and crystallinity, granule size distribution, amylose content, amylose-lipid dissociation properties), a statistically significant change only occurred for the triple nulls, indicating that all three genes had to be missing or inactive for a change to occur. These results illustrate the importance of SSIIa in controlling grain and starch properties and the importance of amylopectin fine structure in controlling starch granule properties in wheat.     

Characterization of barley starches of waxy, normal, and high amylose varieties

Four varieties of barley starches, W.B. Merlin, glacier, high amylose glacier, and high amylose hull-less glacier, were isolated from barley seeds. Apparent and absolute amylose contents, molecular size distributions of amylose and amylopectin, amylopectin branch-chain-length distributions, and Naegeli dextrin structures of the starches were analyzed. W.B. Merlin amylopectin had the longest detectable chain length of DP 67, whereas glacier, high amylose glacier and high amylose hull-less glacier amylopectins had the longest detectable chain length of DP 82, 79, and 78, respectively. All the four starches displayed a substantially reduced proportion of chains at DP 18–21. Amylopectins of high amylose varieties did not show significantly larger proportions of long chains than that of normal and waxy barley starch. Onset gelatinization temperatures of all four barley starches ranged from 55.0 to 56.5°C. Absolute amylose contents of W.B. Merlin, glacier, high amylose glacier, and high amylose hull-less glacier were 9.1, 29.5, 44.7, and 43.4%, respectively; phospholipid contents were 0.36, 0.78, 0.79, and 0.97%, respectively.     

Physicochemical properties of endosperm and pericarp starches during maize development

Endosperm starch and pericarp starch were isolated from maize (B73) kernels at different developmental stages. Starch granules, with small size (2–4 μm diameter), were first observed in the endosperm on 5 days after pollination (DAP). The size of endosperm-starch granules remained similar until 12DAP, but the number increased extensively. A substantial increase in granule size was observed from 14DAP (diameter 4–7 μm) to 30DAP (diameter10–23 μm). The size of starch granules on 30DAP is similar to that of the mature and dried endosperm-starch granules harvested on 45DAP. The starch content of the endosperm was little before 12DAP (less than 2%) and increased rapidly from 10.7% on 14DAP to 88.9% on 30DAP. The amylose content of the endosperm starch increased from 9.2% on 14DAP to 24.2% on 30DAP and 24.4% on 45DAP (mature and dried). The average amylopectin branch chain-length of the endosperm amylopectin increased from DP23.6 on 10DAP to DP26.9 on14DAP and then decreased to DP25.4 on 30DAP and DP24.9 on 45DAP. The onset gelatinization temperature of the endosperm starch increased from 61.3 °C on 8DAP to 69.0 °C on 14DAP and then decreased to 62.8 °C on 45DAP. The results indicated that the structure of endosperm starch was not synthesized consistently through the maturation of kernel. The pericarp starch, however, showed similar granule size, starch content, amylose content, amylopectin structure and thermal properties at different developmental stages of the kernel.     

Starch biosynthesis of amylomaize during endosperm development

In an attempt to investigate starch biosynthesis of amylomaize, the endosperm starches from four genotypes with different doses of amylose-extender (ae) between 0 and 3 were isolated at 14, 18, 22, 28, and 36 days after pollination, and their properties were examined. Gene effects of ae on the endosperm starches were found in the apparent amylose content from measurements of iodine binding capacity and in the elution pattern from fractionation of starches debranched by isoamylase on Sephadex G-75. With increasing doses of ae, the lengths of two side-chain fractions of amylopectin in the original starch granule and the carbohydrate content of shorter side-chain fraction both increased. However, the length of each side chain fraction varied little between 14 and 36 days in all genotypes. In addition, the amylose content in ae homozygous at the 14-day stage was ca 24 % lower than the value of amylose and intermediate fractions in the original starch granule.     

Genotype-specific spatial distribution of starch molecules in the starch granule: a combined CLSM and SEM approach

Starch granule types from a variety of botanical sources were selected to represent differences in crystalline polymorph, amylose and phosphate content, and amylopectin chain length distribution. Equimolar labeling of starch molecules with the fluorophore 8-amino-1,3,6-pyrenetrisulfonic acid (APTS) was used to construct a detailed map of the distribution of amylose and amylopectin within the granule by confocal laser scanning microscopy (CLSM) analysis. Medium- and high-resolution scanning electron microscopy (SEM) were used to provide detailed images of granule surface structures. By using a combined surface and internal imaging approach, interpretations of a number of previous structural observations is presented. In particular, internal images of high amylose maize and potato suggest that multiple initiations of new granules are responsible for the compound or elongated structures observed in these starches. CLSM optical sections of rice granules revealed an apparent altered distribution of amylose in relation to the proposed growth ring structure, hinting at a novel mechanism of starch molecule deposition. Well-described granule features, such as equatorial grooves, channels, cracks, and growth rings were documented and related to both the internal and external observations. A new method for probing the phosphate distribution in native granules was developed using a phosphate-binding fluorescent dye and CLSM.     

Structure–function relationships in A and B granules from wheat starches of similar amylose content

Five wheat (Triticum aestivum L.) starches, from the varieties Sunco, Sunsoft, SM1118, and SM1028, with similar amylose content, and a waxy wheat were separated into large (A) and small (B) granules. The unfractionated starches, and isolated A and B granules, were characterized structurally and evaluated for their functional properties. The amylopectin chain length distribution revealed that A granules had a lower proportion of short chains with degree of polymerization (DP) 6-12 and a higher proportion of chains with DP 25-36 than B granules. X-ray diffraction (XRD) patterns showed predominantly A-type crystallinity for all of the starches. No differences in the crystallinity were found between unfractionated, A and B granules. Small-angle X-ray scattering (SAXS) patterns of the starches at 55% hydration showed that the lamellar repeat distance in A granules was larger than that of B granules for all the starches examined. However, the lamellar distances of both A and B granules from the waxy wheat were smaller than those of Sunco, Sunsoft, SM1118 and SM1028 starches. The swelling power of the B granules was greater than that of A granules from all five starches. The kinetics of digestion of A and B granules with α-amylase in vitro were complex, with B granules initially digested to a greater extent than A granules. After 4 h of incubation, A granules showed greater digestibility than B granules, except in the case of waxy starch where unfractionated and fractionated granules had similar in vitro digestibility. Correlations between structural and functional parameters were more significant for the isolated A and B granules than for the unfractionated starches. This study demonstrates that A and B granules differ in structure and functionality, and that some correlations between these properties could be masked in unfractionated starches with bimodal granule size distribution.