Statistical modeling and optimization of biomass granulation and COD removal in UASB reactors treating low strength wastewaters

The aim of this work was to study the influence of influent chemical oxygen demand (COD), upflow velocity of wastewater, and cationic polymer additives in inoculum, on biomass granulation and COD removal efficiency in upflow anaerobic sludge blanket (UASB) reactor for treating low strength wastewater. Statistical models were formulated based on these three variables to optimize the biomass granulation and COD removal efficiency in UASB reactors using a two-level, full factorial design. For the thick inoculum used in this study, having suspended solids (SS) >80 g/l and volatile suspended solids (VSS) to SS ratio <0.3, cationic polymer additives in the inoculum showed adverse effect on biomass granulation and COD removal efficiency. It is concluded that for such thick inoculum, granulation can be obtained while treating low strength wastewaters in UASB reactor by selecting proper combination of influent COD and liquid upflow velocity so as to represent the organic loading rate (OLR) greater than 1.0 kg COD/m(3) d. Validation of model predictions for treatment of synthetic wastewater and actual sewage reveals the efficacy of these models for enhancing granulation and COD removal efficiency.     

Effects of cationic polymer on performance of UASB reactors treating low strength wastewater

The effect of cationic polymer additives on biomass granulation and COD removal efficiency had been examined in lab-scale upflow anaerobic sludge blanket (UASB) reactors, treating low strength synthetic wastewater (COD 300-630 mg/l). Under identical conditions, two reactors were operated with and without polymer additives in inoculum under four different organic loading rates (OLRs). The optimum polymer dose was adopted based upon the results of jar test and settling test carried out with inoculum seed sludge. With the use of thick inoculum, SS greater than 110 g/l and VSS/SS ratio less than 0.3, granulation was observed in UASB reactor treating synthetic wastewater as well as actual sewage, when OLR was greater than 1.0 kg COD/m(3) d. Polymer additive with such thick inoculum was observed to deteriorate percentage granules and COD removal efficiency compared to inoculum without polymer additives. At OLR less than 1.0 kg COD/m(3) d, proper granulation could not be achieved in both the reactors inoculated with and without polymer additive. Also, under this low loading, drastic reduction in COD removal efficiency was observed with polymer additives in inoculum. Hence, it is rational to conclude that biomass granulation for treatment of low strength biodegradable wastewater depends on the applied loading rate and selection of thick inoculum sludge.     

Anaerobic treatment of a chemical synthesis-based pharmaceutical wastewater in a hybrid upflow anaerobic sludge blanket reactor

In this study, performance of a lab-scale hybrid up-flow anaerobic sludge blanket (UASB) reactor, treating a chemical synthesis-based pharmaceutical wastewater, was evaluated under different operating conditions. This study consisted of two experimental stages: first, acclimation to the pharmaceutical wastewater and second, determination of maximum loading capacity of the hybrid UASB reactor. Initially, the carbon source in the reactor feed came entirely from glucose, applied at an organic loading rate (OLR) 1 kg COD/m(3) d. The OLR was gradually step increased to 3 kg COD/m(3) d at which point the feed to the hybrid UASB reactor was progressively modified by introducing the pharmaceutical wastewater in blends with glucose, so that the wastewater contributed approximately 10%, 30%, 70%, and ultimately, 100% of the carbon (COD) to be treated. At the acclimation OLR of 3 kg COD/m(3) d the hydraulic retention time (HRT) was 2 days. During this period of feed modification, the COD removal efficiencies of the anaerobic reactor were 99%, 96%, 91% and 85%, and specific methanogenic activities (SMA) were measured as 240, 230, 205 and 231 ml CH(4)/g TVS d, respectively. Following the acclimation period, the hybrid UASB reactor was fed with 100% (w/v) pharmaceutical wastewater up to an OLR of 9 kg COD/m(3) d in order to determine the maximum loading capacity achievable before reactor failure. At this OLR, the COD removal efficiency was 28%, and the SMA was measured as 170 ml CH(4)/g TVS d. The hybrid UASB reactor was found to be far more effective at an OLR of 8 kg COD/m(3) d with a COD removal efficiency of 72%. At this point, SMA value was 200 ml CH(4)/g TVS d. It was concluded that the hybrid UASB reactor could be a suitable alternative for the treatment of chemical synthesis-based pharmaceutical wastewater.     

Treatment of brewery slurry in thermophilic anaerobic sequencing batch reactor

Treatment of brewery slurry in a thermophilic anaerobic sequencing batch reactor (ASBR) was studied using conventional fully mixed semi-continuous digestion as a control. The process phases were adapted to fit the brewery slurry discharge schedule. ASBR experiments were conducted under different organic loading rates (OLR) from 3.23 to 8.57 kg of COD/m(3)day of reactor and control was conducted with OLR of 3.0 kg of COD/m(3)day. The ASBR COD degradation efficiency was from 79.6% to 88.9%, control experiment efficiency was 65%. ASBR VSS removal efficiency was from 78.5% to 90.5%, control experiment efficiency was 54%. The ASBR methane production yield was from 371 to 418 L/kg COD inserted, control experiment methane yield was 248 L/kg COD inserted. The ASBR process was superior to conventional fully mixed digestion, and is fully adaptable to brewery slurry discharge, needs no additional collection and settling pools and experiences no solids settling problems.     

Aerobic granulation under the combined hydraulic and loading selection pressures

Two SBR reactors were set up to investigate the feasibility of aerobic granulation under the combined selection pressures of hydraulic shear force and substrate loading. Aerobic granulation was studied at superficial upflow air velocity of 3.2 and 2.4 cm/s under an organic loading rate (OLR) range of 6.0-15.0 kg COD/m3d. Good reactor performance and well granule characteristics were achieved in a wide OLR range from 6.0 high up to 15.0 kg COD/m3d at 3.2 cm/s. While under the velocity of 2.4 cm/s, stable operation was limited in the OLR range of 6.0-9.0 kg COD/m3d and failed to operate with granule deterioration under further higher OLRs. The optimal combination of hydrodynamic shear force and loading selection pressure was demonstrated to be an important factor that influence aerobic granulation and govern the granule characteristics and reactor performance.     

Treatment of low strength industrial cluster wastewater by anaerobic hybrid reactor

The study was aimed at treating the complex, combined wastewater generated in Mangolpuri industrial cluster. It was considered as a low strength wastewater with respect to its organic content. Anaerobic treatment of this wastewater was studied using an anaerobic hybrid reactor (AHR) which combined the best features of both the upflow anaerobic sludge blanket (UASB) reactor and anaerobic fluidized bed rector (AFBR). The performance of the reactor under different organic and hydraulic loading rates were studied. The COD removal reached 94% at an organic loading rate (OLR) of 2.08 kg COD m(-3)d(-1) at an hydraulic retention time (HRT) of 6.0 h. The granules developed were characterized in terms of their diameter and terminal settling velocity.     

Effects of temperatures and organic loading rates on biomethanation of acidic petrochemical wastewater using an anaerobic upflow fixed-film reactor

The effect of temperature and organic loading rate on the rate of methane production from acidic petrochemical wastewater without neutralization was investigated by continuously feeding an anaerobic upflow fixed-film reactor. The temperatures selected for the studies were 25, 37, 45 and 55 degrees C. Organic loading rate (OLR) for each temperature was varied from 3.6 to 21.7 kg COD m(-3) d(-1). Best performance with respect to COD and BOD reduction, total gas production and methane yield was obtained with the reactor operating at 37 degrees C. OLR could be increased to a maximum of 21.7 kg COD m(-3) d(-1) with 90-95% COD and BOD reduction and methane yield of 0.450 m3 kg(-1) COD d(-1) added. The reactor operating at 55 degrees C gave the highest methane yield of 0.666 m3 kg(-1) COD d(-1) at an OLR of 6 kg COD m(-3) d(-1). This decreased to 0.110 m3 kg(-1) COD d(-1) when the OLR was increased to 18.1 kg COD m(-3) d(-1). The reactor operating at 45 degrees C gave a maximum methane yield of 0.416 m3 kg(-1) COD d(-1) added at an OLR of 6 kg COD m(-3) d(-1). On further increasing the OLR to 9 kg COD m(-3) d(-1), COD reduction was 89%, however, methane yield decreased to 0.333 m3 kg(-1) COD d(-1) added. The highest methane yield of 0.333 m3 kg(-1) COD d(-1) added at an OLR of 6 kg COD m(-3) d(-1) was obtained with reactors operating at 25 degrees C. These studies indicate potential rates of methane production from acidic petrochemical wastewater under different temperatures. This provides a guideline for various kinetic analyses and economic evaluation of the potential feasibility of fermenting acidic wastewater to methane.     

Co-degradation of resorcinol and catechol in an UASB reactor

Co-degradation of resorcinol and catechol was studied in a catechol acclimated up flow anaerobic sludge blanket (UASB) reactor. Synthetic binary aqueous solution having a total concentration of 1000 mg/L with the resorcinol/catechol (R/C) ratio of 1/19, 1/9, 3/17, 1/4, 1/3, 3/7, 2/3 and then 1/3 was fed at various time intervals to the UASB reactor with a fixed organic loading rate of 5.7 kg COD/m(3) d and hydraulic retention time of 8h. The reactor was operated over a period of 145 days after its acclimation with catechol bearing synthetic wastewater at a constant feed rate of 1.2 L/h. When the resorcinol concentration was increased to have a R/C ratio of 1/4, the COD removal efficiency and the biogas production increased to the maximum levels. Pseudo steady state condition for COD removal was achieved at each of the stepped-up loading condition. An increase in the R/C ratio above 1/4 in the binary feed solution led to a decrease in the COD removal efficiency and the biogas production rate.     

Start-up of an anaerobic hybrid (UASB/filter) reactor treating wastewater from a coffee processing plant

The ability of an anaerobic hybrid reactor, treating coffee wastewater, to achieve a quick start-up was tested at pilot scale. The unacclimatized seed sludge used showed a low specific methanogenic activity of 26.47 g CH4 as chemical oxygen demand (COD)/kg volatile suspended solids (VSS) x day. This strongly limited the reactor performance. After a few days of operation, a COD removal of 77.2% was obtained at an organic loading rate (OLR) of 1.89 kg COD/m3 x day and a hydraulic retention time (HRT) of 22 h. However, suddenly increasing OLR above 2.4 kg COD/m3 x day resulted in a deterioration in treatment efficiency. The reactor recovered from shock loads after shutdowns of 1 week. The hybrid design of the anaerobic reactor prevented the biomass from washing-out but gas clogging in the packing material was also observed. Wide variations in wastewater strength and flow rates prevented stable reactor operation in the short period of the study.     

Study on biomethonization of waste water from jam industries

Anaerobic digestion of wastewater from jam industries was studied in a continuous reactor with different organic loading rates (OLR) and the optimum organic loading rate was 6.5 kg COD/m(3)/day when it was operated with three days HRT. The biodegradability of wastewater in batch experiments was about 90%. The removal efficiency of total COD and soluble COD were found to 82% and 85%, respectively. The specific methane production was 0.28 m(3)/kg of COD removed/day.     

Effect of feeding strategy on the stability of anaerobic sequencing batch reactor responses to organic loading conditions

The goal of this study was to examine the effect of feeding strategy on the capability for treatment and the stability of an anaerobic sequencing batch reactor (ASBR) under increasing organic loading. The lab-scale ASBR systems were operated at 35 degrees C using synthetic organic wastewater under both batch and fed-batch operational modes with different feed to cycle time (F:C) ratios. Experimental studies were conducted over a wide range of volumetric organic loading rates (VOLRs) (1.524 g COD/l/d) by varying the hydraulic retention time (HRT) (1.25, 2.5, and 5d) and the feed wastewater's COD (3750-30,000 mg/l). With an F:C ratio greater than or equal to 0.42, the fed-batch mode operation showed higher system efficiency in COD removal, volumetric methane production rate (VMPR), and specific methane production rate (SMPR) as compared to those in the batch mode with identical VOLR and HRT. In the fed-batch mode, the COD removals reached 86-95% with VOLR up to 12 g COD/l/d. The maximums for VMPR of 3.17 l CH4/l/d and for SMPR of 1.63 g CH4-COD/g VSS/d were achieved with a VOLR of 12 g COD/l/d at HRTs of 2.5 and 1.25 d, respectively. The fed-batch operation presented a lower concentration of volatile fatty acids (VFAs) than those in the batch operation. A lower concentration of VFAs confirmed the stability and efficiency of the fed-batch mode operation. The specific methanogenic activity (SMA) analysis showed that the VFA-degrading activity of the biomass in the fed-batch mode was higher for acetate and butyrate, and lower for propionate. Determined biomass yield and bacterial decay coefficients in the fed-batch operational mode were 0.05 g VSS/g COD rem and 0.001 d(-1), respectively.     

Enhancing digestion efficiency of POME in anaerobic sequencing batch reactor with ozonation pretreatment and cycle time reduction

Ozonation pretreatment was applied to palm oil mill effluent (POME) prior to anaerobic digestion using the anaerobic sequencing batch reactor (ASBR). Ozonation increased BOD/COD by 37.9% with a COD loss of only 3.3%. At organic loads of 6.48-12.96 kg COD/m³/d, feeding with non-ozonated POME caused a system failure. The ozonated POME gave significantly higher TCOD removal at loadings 6.52 and 9.04 kg COD/m³/d but failed to sustain the operation at loading 11.67 kg COD/m³/d. Effects of cycle time (CT) and hydraulic retention time (HRT) were determined using quadratic regression model. The generated response surface and contour plot showed that at this high load conditions (6.52-11.67 kg COD/m³/d), longer HRT and shorter CT gave the ASBR higher organic removal efficiency and methane yield. The model was able to satisfactorily describe the relationship of these two key operating parameters.     

Two-stage anaerobic treatment of dairy wastewater using HUASB with PUF and PVC carrier

In the present study, an attempt has been made to treat dairy wastewater entirely via anaerobic treatment over a period of 215 days, using two-stage Hybrid Upflow Anaerobic Sludge Blanket (HUASB) reactors, which offer the advantages associated both with fixed film and upflow sludge blanket treatments. A HUASB with polyurethane foam cubes was used for stage I, and a HUASB utilizing PVC-cut rings was used for stage II. The output from stage I was used as the input for stage II. The two-stage reactor was operated at an organic loading rate that varied from 10.7 to 21.4 kg COD m³/d for a period of 215 days, including the start-up period. The ideal organic loading rate for the two-stage reactor was 19.2 kg COD/m³/d. A further 21.4 kg COD m³/d increase in the organic loading rate resulted in the souring of the reactor function in stage I, which consequently reduced the overall reactor performance. Combined COD removal during the stable operation period (10.7 to 19.2 kg COD m³/d) occurred in a range between 97 and 99%. The methane content in the biogas varied from 65 to 70% in stage I, and from 63 to 66% in stage II. The two-stage anaerobic treatment using HUASB with PUF and PVC described in this work is expected to constitute a better alternative for the complete treatment of dairy wastewater than high-rate anaerobic, anaerobic/aerobic, and two-phase anaerobic treatment methods.     

Performance of anaerobic contact filter in series for treating distillery spentwash

Investigations were carried out by using rigid polyurethane foam as a packing material in the anaerobic contact filter (series) to treat distillery spentwash. The effect of hydraulic retention time (HRT) in treatment efficiency of reactor (I) and (II) was evaluated at different initial substrate concentrations ranging from 1500 mg/l to 19,000 mg/l. The effect of toxic parameters such as sulphate present in the distillery spentwash and the corresponding parameters such as total sulphide and un-ionized hydrogen sulphide generated during digestion of wastewater were evaluated to assess the reactor performance. The results showed that at 4 d HRT the overall COD removal percent ranged from 98% to 73% for an influent COD of 1500 mg/l to 19,000 mg/l. The overall performance of COD removal percent in reactor (I) and (II) at 2, 3 and 4 d HRT's were investigated. At 3 d HRT the reactor (II) showed a higher COD removal percent when compared to reactor (I), which clearly shows the role of hydraulic retention time in degradation of the organic matter present in the wastewater above an influent COD concentration of 5000 mg/l.     

Performance of a periodic anaerobic baffled reactor fed on Chinese traditional medicine industrial wastewater

A four-compartment periodic anaerobic baffled reactor (PABR) was run in a 'clockwise sequential' switching manner continuously fed on chinese traditional medicine industrial wastewater under an alkalinity concentration between 1000 and 1500 mg CaCO(3)/L of the feed with average organic load rate (OLR) at about 1, 2, 4 and 6 kg COD/(m(3)d) for 12, 24, 24 and 6d, respectively. Hydraulic residence time was 2d, while switching period was 4d. As the average OLR increased to 6 kg COD/(m(3)d), the time of the sharp fall in pH, chemical oxygen demand (COD) removal, gas production and methane percentage of the biogas of all the compartments and the time of rapid volatile fatty acids accumulation in effluent coincided, hence the PABR became sour. Denaturing gradient gel electrophoresis (DGGE) community fingerprints and their cluster analysis revealed that community structures of each compartment tended to be more closely related if the PABR was not overloaded.     

Characterization of aerobic granules by microbial density at different COD loading rates

Aerobic granules were cultivated under temporal alternating aerobic and anoxic conditions without the presence of a carrier material in a sequencing batch reactor (SBR) with a high column height/column diameter ratio. The reactor was operated for 6h per cycle (aerobic: 4.75 h, anoxic: 1.25 h). To determine a new parameter for the definition of aerobic granules, a protocol of 4,6-diamidino-2-phenylindole hydrochloride staining and fluorescence image processing was developed. The d(tm) analysis showed that the increase in the chemical oxygen demand (COD) loading rate promoted no more growth of the aerobic granules. It was inconsistent with the results of the analysis of the sludge volume index (SVI) value but matched well with the results of the COD and nitrogen removal of the SBR and the particle size distribution by LS-PSA. The optimum COD loading rate for aerobic granulation in the SBR was 2.52 kg/m(3)d. When d(tm) was correlated with the biomass concentration and the SVI value during the period of granule formation, d(tm) could be used as a more sensitive and accurate parameter for classifying aerobic granules and optimizing the operational conditions for aerobic granulation processes.     

Aerobic granulation with brewery wastewater in a sequencing batch reactor

Aerobic granular sludge was cultivated in a sequencing batch reactor fed with brewery wastewater. After nine-week operation, stable granules with sizes of 2-7 mm were obtained. With the granulation, the SVI value decreased from 87.5 to 32 mL/g. The granular sludge had an excellent settling ability with the settling velocity over 91 m/h. Aerobic granular sludge exhibited good performance in the organics and nitrogen removal from brewery wastewater. After granulation, high and stable removal efficiencies of 88.7% COD(t), 88.9% NH(4)(+)-N were achieved at the volumetric exchange ratio of 50% and cycle duration of 6h. The average COD(t) and COD(s) of the effluent were 212 and 134 mg/L, respectively, and the average effluent ammonium concentration was less than 14.4 mg/L. Nitrogen was removed due to nitrification and simultaneous denitrification in the inner core of granules.     

A pilot plant study using a vertically moving biofilm process to treat municipal wastewater

The pilot plant study comprised the construction and monitoring of a new vertically moving biofilm system (VMBS) for treating municipal wastewater. The system operated on site for 11 months. The biofilm module in this system, consisting of high surface area plastic media, was vertically and repeatedly moved in cycles up into the air and down into the wastewater. The vertical movement of the biofilm module supplied sufficient oxygen for the removal of the organic carbon in the wastewater. The overall physical oxygen transfer coefficient (Kla) measured at the cycle speed of six cycles per minute was 2.53 per hour. During the pilot study, dissolved oxygen (DO) concentrations in the bulk fluid were in the range of 1.5-5 mg/l. It was found that the areal removal rate of filtered chemical oxygen demand (COD) was up to 35 g COD/(m(2)day) and the bulk fluid volumetric filtered COD removal rate was 2.62 kg COD/(m(3)day). The field experiment showed that clogging commonly found in other biofilm systems did not occur in this system. The power consumption was in the range of 0.09-0.25 k Wh/m(3) wastewater flow, 0.40-2.19 k Wh/kg COD removal and 1.24-1.74 k Wh/kg BOD removal. The new biofilm system offers potential for reduced reactor volumes, energy saving, simple construction and easy operation.     

Ambient temperature treatment of low strength wastewater using anaerobic sequencing batch reactor

Low strength wastewater having chemical oxygen demands (COD) concentrations of 1000, 800, 600 and 400mg/l were treated at 35, 25, 20 and 15¡C using four anaerobic sequencing batch reactors (ASBRs). Reactor 1 was operated at hydraulic retention time (HRT) of 48h, reactor 2 at 24h HRT, reactor 3 at 16h HRT and reactor 4 at 12h HRT. 80 to 99% soluble COD was removed at the various operational conditions, except during 15¡C treatment of 1000 and 800mg/l COD wastewater at 12h HRT and 1000mg/l COD wastewater at 16h HRT, where excessive loss of biological solids occurred. The ASBR process can be an effective process for the treatment of low concentrated wastewaters which are usually treated aerobically with large amount of sludge production and higher energy expenditures.     

Performances of a full-scale novel multiplate anaerobic reactor treating cheese whey effluent

A 450-m(3) multiplate anaerobic reactor (MPAR) has been started-up in April 1992 for treating wastewater (whey permeate and domestic wastewater) at the Nutrinor (Lactel) cheese factory in Chambord (Québec, Canada). The MPAR consists of four superimposed sections. The liquid flows upwards from one section to the next, while the gas is collected below each plate and evacuated through side-outlets. The wastewater is concurrently distributed at the bottom of the first, second, and third sections, as 50%, 33%, and 17% of the total influent stream, respectively. Granular anaerobic sludge at an initial concentration of 30 kg of volatile suspended solids (VSS) per cubic meter of reactor liquid volume was used to inoculate the reactor. Under normal operation of the factory, the chemical oxygen demand (COD) concentration of the influent ranged from 20 to 37 kg COD m(-3). The reactor organic loading rate (OLR) fluctuated between 9 and 14.7 kg COD m(-3) d(-1) for hydraulic retention times (HRT) maintained between 55 and 68 h. At the highest OLR, the MPAR showed an efficiency of 98% and 92% for soluble and total COD removal, respectively, and a methane production rate averaging around 4 m(3) m(-3) d(-1).Biomass-specific activities ranged between 7 and 51, 1.3 and 8.5, 5.3 and 12.2, 60 and 119, and 119 and 211 mmol g(-1) VSS d(-1) for glucose, propionate, acetate, formate, and hydrogen, respectively. Average equivalent-diameter of the granules was around 0.65 mm. The MPAR reactor generally showed a large capacity for solid retention with a biomass content between 32 and 37 kg VSS m(-3). (c) 1995 John Wiley & Sons, Inc.