Optimization of ascorbic and uric acid separation in human plasma by free zone capillary electrophoresis ultraviolet detection

In this paper we propose a new fast free zone capillary electrophoresis method for the simultaneous determination of ascorbic acid (AA) and uric acid (UA) in human plasma. We investigated the effect of analytical parameters, such as concentration and pH of borate running buffer, cartridge temperature, and sample treatment, on resolution, migration times, corrected peak areas, and efficiency. A good separation was achieved using a 60.2-cmx75-microm uncoated silica capillary and 100 mmol/L sodium borate buffer, pH 8, when metaphosphoric acid was employed as protein precipitant, in less than 4 min. These conditions gave a good reproducibility of migration times (CV 0.35 and 0.34%) and peak areas (CV 3.2 and 3.1%) for ascorbate and urate, respectively. The limit of detection was 0.5mg/L for both analytes when the detection was performed at 254 nm for AA and at 292 nm for UA. We compared the present method with a validated capillary electrophoresis assay by measuring plasma urate and ascorbate in 32 normal subjects and the obtained data were analyzed by the Passing and Bablok regression.     

Bilirubin removal from human plasma by Cibacron Blue F3GA using immobilized microporous affinity membranous capillary method

A novel affinity sorbent system for direct bilirubin removal from human plasma was developed. These new adsorbents comprise Cibacron Blue F3GA as the specific ligand, and microporous membranous poly(tetrafluoroethylene) capillary (modified by coating with a hydrophilic layer of poly(vinyl alcohol) after activation) as the carrier matrix. The affinity adsorbents carrying 126.5 micromol Cibacron Blue F3GA/g polymer was then used to remove bilirubin in a flow-injection system. Non-specific adsorption on the poly(vinyl alcohol) coated capillary remains low, and higher affinity adsorption capacity, of up to 76.2 mg/g polymer was obtained after dye immobilization. The bilirubin adsorption capacity of the affinity capillary decreased with increase in the recirculation rate of plasma. The adsorption capacity increased with increase the temperature while decreased with increase the ionic strength. The maximum adsorption was only observed in neutral solution (pH 6-7). The adsorption isotherm fitted the Langmuir model well. These new adsorbents have higher velocity of mass transfer, better adsorption capacity, less fouling, longer service life and good reusability. The results of blood tests suggested the dye affinity capillary has good blood compatibility.     

Pre-analytical factors affecting ascorbic and uric acid quantification in human plasma

We have recently described a new capillary electrophoresis assay to measure serum ascorbic and uric acids in which a baseline separation of peaks was obtained in less than 4 min by using a 60.2 cm x 75 microm uncoated capillary with a 100 mmol/L sodium borate running buffer pH 8. Since during sample preparation AA is rapidly oxidized, we employed our new capillary electrophoresis method to analyze the pre-analytical factors affecting its stability. In particular we evaluated how the standard mix preparation, the blood collection (plasma EDTA or serum) and the plasma protein precipitation influence the results of analysis. Our data suggest that standard ascorbate must be dissolved in a solution containing cysteine and EDTA in order to avoid oxidation and that EDTA blood collection is better than serum for AA measurement. Moreover, the type and the quantity of the precipitating compound are critical parameters to obtain a complete recovery of analytes. We performed AA and UA analysis in 32 healthy volunteers with the optimized experimental conditions by using our capillary electrophoresis method and a reference CE assay. Obtained data were compared to Bland-Altman test to verify the accuracy of our CZE method.     

Blood gas analysis of bovine fetal capillary blood during stage II labor

The aim of this study was to determine whether blood gas variables in fetal capillary blood during the last 30 min of stage II labor can be used to diagnose fetal asphyxia. Twenty-five newborn calves were used to investigate the correlation between capillary blood gas values obtained from the dorsolateral aspect of the distal pastern and those in arterial and venous blood. The pH, partial pressure of oxygen, partial pressure of carbon dioxide, concentration of bicarbonate, base excess and oxygen saturation were determined. The bicarbonate concentration (arterial, r=0.759; venous, r=0.766; both P<0.0001) and base excess (arterial, r=0.730; venous, r=0.807; both P<0.0001) had the highest correlations. Fetal capillary blood was collected during the last 30 min of stage II labor and the results of blood gas analysis were compared with those of arterial and venous blood collected immediately after birth in 38 calves. The pH (arterial, r=0.806; venous, r=0.885; both P<0.0001) and base excess (arterial, r=0.822; venous, r=0.871; both P<0.0001) had the highest correlations. The pH and base excess were significantly lower after birth than during the last 30 min of stage II labor. The severity of fetal acidosis during stage II labor can be easily and reliably determined using the pH or base excess of fetal capillary blood.     

Comparative study of automatic blood-gas analysers and their use in analysing arterial and capillary samples.

Three automatic blood-gas analysers were compared for ease of use; calibration; reproducibility and accuracy of results; maintenance; fault-finding; and use of expert technician time. Results obtained from arterial and capillary blood were compared with duplicate values obtained with a semi-automatic analyser controlled and calibrated with tonometered blood. No analyser was fully automatic, and all three needed maintenance by expert technicians. Difficulties were encountered when inexperienced operators used the machines. One automatic blood-gas analyser gave aberrant values for oxygen pressure (PO2) due to electrode dysfunction that was not indicated by the fault-finding system. A second analyser gave significantly lower values for blood pH than the standard machine. A comparison of pH, carbon dioxide pressure (PCO2), and PO2 measured in 40 simultaneous paired samples of arterial and arterialised capillary blood showed no significant difference for pH or PCO2, but the PO2 values were significantly lower in the capillary samples over the range studied. We conclude that all machines perform satisfactorily in terms of blood-gas analysis, but none may be regarded as fully automatic. Some degree of technical supervision is essential, as is proper training for all potential users.     

Application of capillary zone electrophoresis to study the properties of rhodanese fromAcidithiobacillus ferrooxidans

A new capillary zone electrophoretic method was applied to the assay of enzymic activity of rhodanese from Acidithiobacillus ferroxidans. The enzyme activity determined by capillary zone electrophoresis was compared with that determined by discontinuous spectrophotometry, the values obtained being in good agreement. The method was also used to evaluate Michaelis constants of cyanide and thiocyanate as substrates; a new approach was developed to solve the problem with variable ionic strength of the samples. The pH and temperature optima for the enzyme were also determined.     

Enantioselective separation of phenylglycidates by capillary electrophoresis employing sulfated beta-cyclodextrin as chiral selector

A capillary electrophoresis (CE) method for the enantioseparation of phenylglycidates has been developed. Successful enantioseparation was achieved using sulfated beta-cyclodextrin as chiral selector in a phosphate buffer. The effects of varying pH, sulfated beta-cyclodextrin concentration and electrophoresis voltage were systematically investigated and the optimized separation conditions were thus obtained. When the migration time was set at the threshold value, it was found that the best enantioseparation was obtained at 10 kV with 3% (w/v) sulfated beta-cyclodextrin at pH 6.5. A range of substituted phenylglycidates were successfully separated using the method and the results shown to be superior to those obtained using gas chromatography (GC).     

Highly sensitive profiling assay of acidic plant hormones using a novel mass probe by capillary electrophoresis-time of flight-mass spectrometry

Plant hormones play crucial roles in plant growth and development. However, up to date, identification and quantification of acidic plant hormones with trace amount in complicated plant matrix is still a challenge. In current study, we developed a high sensitive assay for the determination of acidic plant hormones in rice by combining capillary electrophoresis and electrospray ionization-time of flight-mass spectrometry (CE-ESI-TOF-MS). To improve the detection sensitivity of acidic plant hormones, 3-bromoactonyltrimethylammonium bromide (BTA) was synthesized as a new mass probe, which can react efficiently with acidic plant hormones in acetonitrile containing triethylamine (TEA). The positively charged BTA-derivatives were separated by CE using amino-coated capillary, which provided a reversed electroosmotic flow (EOF) at low pH, as well as reduced the adsorption of BTA-derivatives on the inner wall of capillary. Using the CE-ESI-TOF-MS method developed in current study, 15 acidic plant hormones, including 10 gibberellins (GAs), were identified and quantified with good linearities from 1.3 to 850 ng/mL with linear coefficient R(2) values of >0.99. The limits of detection (LODs) were in the range of 0.34-4.59 ng/mL. Recoveries of compounds from spiked beverage samples ranged from 84.6 to 112.2%. And a good reproducibility was obtained by evaluating the intra and inter-day precisions with relative standard deviations (RSDs) less than 6.7 and 9.9%, respectively.     

Separation of new antidepressants and their metabolites by micellar electrokinetic capillary chromatography

Selective serotonin reuptake inhibitors (SSRIs), serotonin noradrenergic reuptake inhibitors (SNaRIs) and noradrenergic and specific serotoninergic antidepressant (NaSSA) are widely used in the treatment of depression. An increase in antidepressant intoxications led to the development of reliable analytical methods for their analysis. A new determination procedure for these compounds (milnacipran, venlafaxine, desmethylvenlafaxine, mirtazapine, desmethylmirtazapine, citalopram, desmethylcitalopram, fluvoxamine, paroxetine, sertraline and fluoxetine) was developed by micellar electrokinetic capillary chromatography (MEKC) with diode array detection (DAD). Separation and determination were optimised on an uncoated fused-silica capillary (600 mm, 75 microm I.D.). The migration buffer consisted of 20 mM sodium borate, pH 8.55, with 20 mM SDS and 15% isopropanol, at an operating voltage of 25 kV. The column temperature was maintained at 40 degrees C. Injection in the capillary was performed in the hydrodynamic mode (0.5 p.s.i., 15 s). In these conditions, the migration time of the antidepressants was less than 11 min. In most cases, calibration curves were established for 30 - 2000 ng/ml (r > 0.995). The limit of detection and the limit of quantification were ranged between 10 and 20 and between 20 and 30 ng/ml, respectively, for all the molecules. This method allowed the determination of some of these compounds in biological fluids (blood, urine) in post-mortem cases. Samples (1 ml) were extracted with diethyl ether (5 ml) at pH 9.6 and reconstituted in diluted migration buffer. Similar results were obtained by a HPLC-DAD determination, performed as a reference method. These results suggest that this MEKC method can be useful for the determination of new antidepressants in post-mortem cases.     

Separation of cefoperazone enantiomers using beta-cyclodextrin as chiral additive by capillary zone electrophoresis

A capillary electrophoresis method was developed to separate the enantiomers of cefoperazone. Different cyclodextrins, including alpha-cyclodextrin (alpha-CD), beta-cyclodextrin (beta-CD), gamma-cyclodextrin (gamma-CD), 2-hydroxypropyl-beta-cyclodextrin (HP-beta-CD), and methyl-beta-cyclodextrin (Me-beta-CD), were tested as chiral additives in the running buffer. The effect of various parameters on enantioseparation such as concentration of NaH(2)PO(4), buffer pH, and CD concentration was also studied. The cefoperazone enantiomers were baseline separated under conditions of 0.04 mmol/L beta-CD, 75 mmol/L NaH(2)PO(4) buffer at pH 4.0. A fused silica capillary (40 cm effective length x 75 microm ID) was used. The applied voltage and capillary temperature were 20 kV and 25 degrees C, respectively. Under these conditions, linear calibration curves were obtained in the 5-500 microg/ml range using UV detection at 280 nm. The limit of detection for both isomers was 0.1 microg/ml. The method was used for the analysis of different pharmaceutical preparations (dose) and biological samples containing cefoperazone.     

Determination of vitamin A in dried human blood spots by high-performance capillary electrophoresis with laser-excited fluorescence detection

We have developed a high-performance capillary electrophoresis (HPCE) method to analyze the retinol (vitamin A) concentration as retinol-retinol binding protein (holo-RBP) from microvolumes of serum (5–10 μl) or one to two drops (∼20 μl) of blood collected and air-dried on blood collection filter paper. A 0.64-cm diameter disk was cut from the dried whole blood specimens and the samples were dissolved in a pretreatment buffer and filtered. Filtrate was injected onto the HPCE column for analysis. The separation was carried out in a 60 cm × 50 μm I.D. fused-silica capillary and the running voltage was 20 kV. A HeCd laser with a wavelength of 325 nm was used for excitation, and the fluorescence of the holo-RBP complex was monitored at 465 nm by a photodiode. A virtual linear relationship was obtained for the retinol concentrations between HPCE and HPLC for 28 serum samples, 19 dried venous blood samples and 9 capillary dried blood spot samples, indicating that valid measures of serum retinol can be obtained from one to two drops of capillary blood collected on filter paper. The absolute detection limit for retinol by HPCE is below 3 μg/l. The method is very useful for vitamin A level screening, especially for children and premature new-born babies.     

Determination of prednisolone and the most important associated compounds in ocular and cutaneous pharmaceutical preparations by micellar electrokinetic capillary chromatography

A micellar electrokinetic capillary chromatographic method to separate prednisolone, prednisolone acetate, naphazoline, Zn-bacitracin, sulfacetamide and phenylefrine is described. The separation was carried out by using a fused-silica capillary (57 cmx75 micrometer I.D.) at 25 degrees C and 30 kV, using a 5 mM phosphate-5 mM borate buffer adjusted to pH 8.2, 50 mM sodium dodecyl sulfate (SDS) and 10% methanol-water (v/v) as background electrolyte. Under these conditions, the run time was 8 min and the limits of quantification were about 1.0 mg/l for every component. The method was applied to pharmaceutical preparations and the results provided recoveries close to 100% and the method gave good results when compared with a reference multivariate calibration spectrophotometric method.     

Simultaneous determination of 19 intracellular nucleotides and nucleotide sugars in Chinese Hamster ovary cells by capillary electrophoresis

Twelve nucleotides and seven nucleotide sugars in Chinese Hamster ovary (CHO) cells were determined by capillary electrophoresis (CE). The CE operating conditions of buffer pH value, ion strength, capillary temperature, polymer additive and cell extraction method were investigated. Optimum separation was achieved with 40 mM sodium tetraborate buffer (pH 9.5) containing 1% (w/v) polyethylene glycol (PEG) at a capillary temperature of 22 degrees C. Acetonitrile and chloroform were used for intracellular extraction. This method can be used to monitor intracellular carbohydrate metabolism.     

Chiral separation of salbutamol and bupivacaine by capillary electrophoresis using dual neutral cyclodextrins as selectors and its application to pharmaceutical preparations and rat blood samples assay

An attempt for the simultaneous separation of salbutamol (Sal) and bupivacaine (Bup) enantiomers was performed by capillary elecytrophoresis with a dual mixture of neutral cyclodextrins as chiral selector. The influence on the separation of several parameters such as buffer composition, pH, the concentration ratio of 2-hydroxypropyl-beta-cyclodextrin (HP-beta-CD) to dimethyl-beta-cyclodextrin (DM-beta-CD) was investigated. A better separation was obtained for Sal and Bup with the CD mixtures compared to the use of HP-beta-CD or DM-beta-CD alone. The best simultaneous separation of Sal and Bup enantiomers was achieved with a 20 mM HP-beta-CD and 20 mM DM-beta-CD at pH 2.5 in a triethanolamine (TEA)/phosphate buffer. This method-utilized chlorphenamine (Chl) as an internal standard was found to be linear in the range 0.5-100 microg/mL and 0.5-150 microg/mL for Sal and Bup enantiomers, respectively. The limits of detection for both enantiomers of Sal and Bup were 0.18 and 0.24 microg/mL, respectively. The proposed method was applied to monitor Sal and Bup enantiomers concentration change in rat blood samples obtained from a male rat after celiac doses administration 0-30 min of Sal and Bup racemate. The method could also be used to determine Sal enantiomers in a pharmaceutical aerosol.     

ITPase Activity in Dry Blood Spots is Comparable with That in Fresh Erythrocytes

Inosine triphosphate pyrophosphohydrolase (ITPase) catalyzing the pyrophosphohydrolysis of inosine triphosphate, deoxyinosine triphosphate and xanthosine triphosphate is involved in the metabolism and tolerance of thiopurine drugs. ITPase activity plays an important role in the prediction of toxicity to thiopurine therapy. Activities in dry blood spots were compared with fresh erythrocytes. Samples were incubated with inosine triphosphate, then inosine monophosphate was determined by a capillary electrophoresis method. Calculated enzyme activities obtained from dry blood spots were in good accordance with activity in fresh erythrocytes.     

ITPase activity in dry blood spots is comparable with that in fresh erythrocytes

Inosine triphosphate pyrophosphohydrolase (ITPase) catalyzing the pyrophosphohydrolysis of inosine triphosphate, deoxyinosine triphosphate and xanthosine triphosphate is involved in the metabolism and tolerance of thiopurine drugs. ITPase activity plays an important role in the prediction of toxicity to thiopurine therapy. Activities in dry blood spots were compared with fresh erythrocytes. Samples were incubated with inosine triphosphate, then inosine monophosphate was determined by a capillary electrophoresis method. Calculated enzyme activities obtained from dry blood spots were in good accordance with activity in fresh erythrocytes.     

Separation of poly(amidoamine) (PAMAM) dendrimer generations by dynamic coating capillary electrophoresis

The separation of compounds possessing amino groups (peptides, proteins, polyamino compounds) by capillary zone electrophoresis suffers from the interaction (sticking) of these solutes with the capillary wall. This sticking can result in the absence or incomplete separation of compounds or even in their retention in the capillary. Polyamidoamine (PAMAM) dendrimers are a class of spherical polymers with primary amino groups at the surface. These compounds can be separated reasonably well at acidic pH but not at neutral pH. A new method based on the dynamic coating of the capillary was developed for the separation of these compounds at pH 7.4. The method comprises separation in a fused-silica capillary (57 cm total length, 50 cm to the detector, ID 75 microm) and a background electrolyte consisting of a Tris-phosphate buffer (50 mmol/L, pH 7.4) and 0.05% (w/v) polyethyleneimine. This system is suitable for the separation of 7 generations of dendrimers (generations 0-6). The dynamic coating agent (polyethyleneimine) also improves the separation at acid pH.     

Determination of urinary hippuric acid by micellar electrokinetic capillary chromatography

We propose a method for the simultaneous determination of hippuric acid (HA) and creatinine based on capillary micellar electrokinetic chromatography. Experimental conditions were 20 mM sodium phosphate, pH 7.20, 25 mM sodium dodecyl sulfate, 5% (v/v) acetonitrile. Electropherograms evidenced HA and creatinine peaks in less than 12 min. The method showed good linearity for both analytes and satisfactory within-day precision. The present method, which is accurate, sensitive, rapid and simple, may be applied to single-spot urine samples.     

Plasma methionine determination by capillary electrophoresis-UV assay: application on patients affected by retinal venous occlusive disease

Methionine is an important amino acid involved in protein synthesis and transmethylation reactions. It is also the precursor of homocysteine and cysteine, two important risk factors for cardiovascular diseases. As homocysteine research has gained impulsion, the evaluation of plasma methionine concentrations has acquired importance. Methionine measurement generally has been performed by HPLC after o-phthalaldehyde derivatization. Its separation from other amino acids is time-consuming. We set up a new specific capillary electrophoresis method in which analyte derivatization was avoided by sample concentration before analysis. Methionine was detected by UV absorbance at 204 nm with a detection limit of 0.5 micromol/L. By a capillary with an effective length of 50 cm filled with 125 mmol/L Tris phosphate buffer at pH 2.3, the separation occurred in less than 14 min. Precision tests indicated a good test repeatability for both migration times (coefficient of variation [CV]<0.3%) and areas (CV<2.0%). Moreover, a good reproducibility of intraassay and interassay tests was obtained (CV<2.9% and CV<3.5%, respectively). The Passing-Bablok regression and the Bland-Altman test for methods comparison suggest that the data obtained by our method and by a reference HPLC assay are similar. Assay performance was evaluated measuring methionine concentrations in retinal venous occlusive disease.     

Determination of high density lipoprotein cholesterol in venous and capillary whole blood

A procedure is presented and evaluated for separation of plasma high density lipoprotein from either capillary or venous whole blood. The lipoprotein is separated by adding 50 microliter of sample to 250 microliter of 0.15 M NaCl solution containing 99.9 g/l polyethyleneglycol 6000, 0.0374 g/l dextran sulfate (Mr 15,000) and 2.6 mM Mg2+. After gentle mixing for a few minutes and standing 10 min at room temperature, mixtures are centrifuged (1,500 g) for 10 min and cholesterol is measured on 200 microliter of supernatant by an enzymatic-colorimetric method. Comparison studies demonstrate a good correlation between high density lipoprotein cholesterol in plasma and capillary or venous whole blood. The procedure is simple, has the advantage of using either K3-EDTA-anticoagulated whole blood, without the need of centrifugation, or capillary whole blood which can also be collected away from the laboratory.