A milliliter-scale yeast-based fuel cell with high performance

Microbial fuel cells are attracting attention as one of the systems for producing electrical energy from organic compounds. We used commercial baker's yeast (Saccharomyces cerevisiae) for a glucose fuel cell because the yeast is a safe organism and relatively high power can be generated in the system. In the present study, a milliliter (mL)-scale dual-chamber fuel cell was constructed for evaluating the power generated by a variety of yeasts and their mutants, and the optimum conditions for high performance were investigated. When carbon fiber bundles were used as an electrode in the fuel cell, high volumetric power density was obtained. The maximum power produced per volume of anode solution was 850 W/m³ under optimum conditions. Furthermore, the power was examined using seven kinds of yeast. In Kluyveromyces marxianus, not only the power but also the power per consumed glucose was high. Moreover, it was suggested that xylose is available as fuel for the fuel cell. The fuel cell powered by K. marxianus may prove to be helpful for the effective utilization of woody biomass.     

Atomic Fe‐Doped MOF‐Derived Carbon Polyhedrons with High Active‐Center Density and Ultra‐High Performance toward PEM Fuel Cells

A metalorganic gaseous doping approach for constructing nitrogen‐doped carbon polyhedron catalysts embedded with single Fe atoms is reported. The resulting catalysts are characterized using scanning transmission electron microscopy, X‐ray photoelectron spectroscopy, and X‐ray absorption spectroscopy; for the optimal sample, calculated densities of Fe–N_x sites and active N sites reach 1.75812 × 10¹³ and 1.93693 × 10¹⁴ sites cm^‐2, respectively. Its oxygen reduction reaction half‐wave potential (0.864 V) is 50 mV higher than that of 20 wt% Pt/C catalyst in an alkaline medium and comparable to the latter (0.78 V vs 0.84 V) in an acidic medium, along with outstanding durability. More importantly, when used as a hydrogen–oxygen polymer electrolyte membrane fuel cell (PEMFC) cathode catalyst with a catalyst loading as low as 1 mg cm^‐2 (compared with a conventional loading of 4 mg cm^‐2), it exhibits a current density of 1100 mA cm^‐2 at 0.6 V and 637 mA cm^‐2 at 0.7 V, with a power density of 775 mW cm^‐2, or 0.775 kW g^–1 of catalyst. In a hydrogen–air PEMFC, current density reaches 650 mA cm^‐2 at 0.6 V and 350 mA cm^‐2 at 0.7 V, and the maximum power density is 463 mW cm^‐2, which makes it a promising candidate for cathode catalyst toward high‐performance PEMFCs.     

Saccharomyces cerevisiae as anodic biocatalyst for power generation in biofuel cell: influence of redox condition and substrate load

Bio (microbial) fuel cell (microbial fuel cell) with Saccharomyces cerevisiae as anodic biocatalyst was evaluated in terms of power generation and substrate degradation at three redox conditions (5.0, 6.0 and 7.0). Fuel cell was operated in single chamber (open-air cathode) configuration without mediators using non-catalyzed graphite as electrodes. The performance was further studied with increasing loading rate (OLRI, 0.91 kg COD/m³-day; OLRII, 1.43 kg COD/m³). Higher current density was observed at pH 6.0 [160.36 mA/m² (OLRI); 282.83 mA/m² (OLRII)] than pH 5.0 (137.24 mA/m²) and pH 7.0 (129.25 mA/m²). Bio-electrochemical behavior of fuel cell was evaluated using cyclic voltammetry which showed the presence of redox mediators (NADH/NAD⁺; FADH/FAD⁺). Higher electron discharge was observed at pH 6.0, suggesting higher proton shuttling through the involvement of different redox mediators. The application of yeast based fuel cell can be extended to treat high strength wastewaters with simultaneous power generation.     

Power overshoot in two-chambered microbial fuel cell (MFC)

A two-chamber microbial fuel cell was started using iron-reducing strains as inoculum and acetate as carbon sources. The tested microbial fuel cell had an open-circuit voltage of 0.67 V, and reached 1045 mA m⁻² and a power density of 486 mW m⁻² at 0.46 V before power overshoot occurred. Anodic reactions were identified as the rate-determining steps. Stirring the anolyte insignificantly increased cell performance, suggesting a minimal external mass transfer resistance from the anolyte to the anodic biofilm. Data regression analysis indicates that charge transfer resistance at the biofilm-anode junction was negligible. The order of magnitude estimation of electrical conductance indicates that electron transfer resistance had an insignificant effect on microbial fuel cell performance. Resistance in electrogens for substrate utilization is proposed to induce microbial fuel cell power overshoot.     

Incorporation of Indium Tin Oxide Nanoparticles in PEMFC Electrodes

Carbon materials suffer from corrosion at the cathode of polymer electrolyte membrane fuel cells (PEMFCs). In the presence of water, carbon support materials are oxidized to carbon dioxide even at low potentials. Hence, nowadays it is very fashionable to look for alternative support materials, like oxides or conductive polymers. To gain the maximum performance for a new material one should also consider an appropriate electrode structure. This study shows the results for the incorporation of nanosized alternative support materials into advanced electrode architectures. Commercially available indium tin oxide (ITO) nanoparticles (<50 nm) are used as support for Pt nanoparticles in combination with Nafion‐coated multi‐walled carbon nanotubes (MWCNTs) on the cathode side of a PEMFC. The MWCNTs promote a high electronic conductivity and help to form a porous network, which could accommodate the Pt/ITO nanoparticles. The microscopic investigations show a homogeneous electrode structure composed of Pt/ITO and MWCNT/Nafion multilayer. Single cell measurements show a maximum power density of 73 mW cm^?2 and a Pt utilization of 1468 mW mg_Pt^?1 for the cathode. The performance data and the Pt utilization are comparable to a standard Pt/carbon black electrode possessing the same Pt loading in the electrode. Beside this, it is shown for the first time that ITO serves as support material under real fuel cell conditions.     

Biaxial Strains Mediated Oxygen Reduction Electrocatalysis on Fenton Reaction Resistant L10‐PtZn Fuel Cell Cathode

PtM alloy catalysts (e.g., PtFe, PtCo), especially in an intermetallic L1₀ structure, have attracted considerable interest due to their respectable activity and stability for the oxygen reduction reaction (ORR) in proton exchange membrane fuel cells (PEMFCs). However, metal‐catalyzed formation of ·OH from H₂O₂ (i.e., Fenton reaction) by Fe‐ or Co‐containing catalysts causes severe degradation of PEM/catalyst layers, hindering the prospects of commercial applications. Zinc is known as an antioxidant in Fenton reaction, but is rarely alloyed with Pt owing to its relatively negative redox potential. Here, sub‐4 nm intermetallic L1₀‐PtZn nanoparticles (NPs) are synthesized as high‐performance PEMFC cathode catalysts. In PEMFC tests, the L1₀‐PtZn cathode achieves outstanding activity (0.52 A mg_Pt^?1 at 0.9 V_iR‐free, and peak power density of 2.00 W cm^?2) and stability (only 16.6% loss in mass activity after 30 000 voltage cycles), exceeding the U.S. DOE 2020 targets and most of the reported ORR catalysts. Density function theory calculations reveal that biaxial strains developed upon the disorder‐order (A1? L1₀) transition of PtZn NPs would modulate the surface Pt? Pt distances and optimize Pt? O binding for ORR activity enhancement, while the increased vacancy formation energy of Zn atoms in an ordered structure accounts for the improved stability.     

Electricity generation at high ionic strength in microbial fuel cell by a newly isolated Shewanella marisflavi EP1

Increasing the ionic strength of the electrolyte in a microbial fuel cell (MFC) can remarkably increase power output due to the reduction of internal resistance. However, only a few bacterial strains are capable of producing electricity at a very high ionic strength. In this report, we demonstrate a newly isolated strain EP1, belonging to Shewanella marisflavi based on polyphasic analysis, which could reduce Fe(III) and generate power at a high ionic strength of up to 1,488 mM (8% NaCl) using lactate as the electron donor. Using this bacterium, a measured maximum power density of 3.6 mW/m² was achieved at an ionic strength of 291 mM. The maximum power density was increased by 167% to 9.6 mW/m² when ionic strength was increased to 1,146 mM. However, further increasing the ionic strength to 1,488 mM resulted in a decrease in power density to 5.2 mW/m². Quantification of the internal resistance distribution revealed that electrolyte resistance was greatly reduced from 1,178 to 50 Ω when ionic strength increased from 291 to 1,488 mM. These results indicate that isolation of specific bacterial strains can effectively improve power generation in some MFC applications.     

Long-term performance of a plant microbial fuel cell with Spartina anglica

The plant microbial fuel cell is a sustainable and renewable way of electricity production. The plant is integrated in the anode of the microbial fuel cell which consists of a bed of graphite granules. In the anode, organic compounds deposited by plant roots are oxidized by electrochemically active bacteria. In this research, salt marsh species Spartina anglica generated current for up to 119 days in a plant microbial fuel cell. Maximum power production was 100 mW m⁻² geometric anode area, highest reported power output for a plant microbial fuel cell. Cathode overpotential was the main potential loss in the period of oxygen reduction due to slow oxygen reduction kinetics at the cathode. Ferricyanide reduction improved the kinetics at the cathode and increased current generation with a maximum of 254%. In the period of ferricyanide reduction, the main potential loss was transport loss. This research shows potential application of microbial fuel cell technology in salt marshes for bio-energy production with the plant microbial fuel cell.     

Electricity generation in a membrane-less microbial fuel cell with down-flow feeding onto the cathode

A novel membrane-less microbial fuel cell (MFC) with down-flow feeding was constructed to generate electricity. Wastewater was fed directly onto the cathode which was horizontally installed in the upper part of the MFC. Oxygen could be utilized readily from the air. The concentration of dissolved oxygen in the influent wastewater had little effect on the power generation. A saturation-type relationship was observed between the initial COD and the power generation. The influent flow rate could affect greatly the power density. Fed by the synthetic glucose wastewater with a COD value of 3500 mg/L at a flow rate of 4.0 mL/min, the developed MFC could produce a maximum power density of 37.4 mW/m². Its applicability was further evaluated by the treatment of brewery wastewater. The system could be scaled up readily due to its simple configuration, easy operation and relatively high power density.     

A microbial fuel cell capable of converting glucose to electricity at high rate and efficiency

A microbial fuel cell containing a mixed bacterial culture utilizing glucose as carbon source was enriched to investigate power output in relation to glucose dosage. Electron recovery in terms of electricity up to 89% occurred for glucose feeding rates in the range 0.5–3 g l^–1 d^–1, at powers up to 3.6 W m^–2 of electrode surface, a five fold higher power output than reported thus far. This research indicates that microbial electricity generation offers perspectives for optimization.     

Granular activated carbon single-chamber microbial fuel cells (GAC-SCMFCs): A design suitable for large-scale wastewater treatment processes

As an emerging biotechnology capable of removing contaminants and producing electricity, microbial fuel cells (MFCs) hold a promising future in wastewater treatment. However, several main problems, including the high internal resistance (R_in), low power output, expensive material, and complicated configuration have severely hindered the large-scale application of MFCs. The study targeted these challenges by developing a novel MFC system, granular activated carbon single-chamber MFC, termed as GAC-SCMFC. The batch tests showed that GAC was a good substitute for carbon cloth and GAC-SCMFCs generated high and stable power outputs compared with the traditional two-chamber MFCs (2CMFCs). Critical operational parameters (i.e. wastewater substrate concentrations, GAC amount, electrode distance) affecting the performance of GAC-SCMFCs were examined at different levels. The results showed that the R_in gradually decreased from 60 Ω to 45 Ω and the power output increased from 0.2 W/m³ to 1.2 W/m³ when the substrate concentrations increased from 100 mg/L to 850 mg/L. However, at high concentrations of 1000–1500 mg/L, the power output leveled off. The R_in of MFCs decreased 50% when the electrode distance was reduced from 7.5 cm to 1 cm. The highest power was achieved at the electrode distance of 2 cm. The power generation increased with more GAC being added in MFCs due to the higher amount of biomass attached. Finally, the multi-anode GAC-SCMFCs were developed to effectively collect the electrons generated in the GAC bed. The results showed that the current was split among the multiple anodes, and the cathode was the limiting factor in the power production of GAC-SCMFCs.     

Pre-acclimation of a wastewater inoculum to cellulose in an aqueous-cathode MEC improves power generation in air-cathode MFCs

Cellulose has been used in two-chamber microbial fuel cells (MFCs), but power densities were low. Higher power densities can be achieved in air-cathode MFCs using an inoculum from a two-chamber, aqueous-cathode microbial electrolysis cell (MEC). Air-cathode MFCs with this inoculum produced maximum power densities of 1070 mW m⁻² (cathode surface area) in single-chamber and 880 mW m⁻² in two-chamber MFCs. Coulombic efficiencies ranged from 25% to 50%, and COD removals were 50-70% based on total cellulose removals of 60-80%. Decreasing the reactor volume from 26 to 14 mL (while maintaining constant electrode spacing) decreased power output by 66% (from 526 to 180 mW m⁻²) due to a reduction in total mass of cellulose added. These results demonstrate that air-cathode MFCs can produce high power densities with cellulose following proper acclimation of the inoculum, and that organic loading rates are important for maximizing power densities from particulate substrates.     

Construction and operation of freshwater sediment microbial fuel cell for electricity generation

In this work, sediment microbial fuel cell (SMFC) with granule activated carbon (GAC) cathode and stainless steel anode was constructed in laboratory tests and various factors on SMFC power output were investigated. The maximum power densities for the SMFC with GAC cathode was 3.5 mW m⁻², it was much higher than SMFC with round stainless steel cathode. Addition of cellulose reduced the output power from SMFC at the beginning of experiments, while the output power was found to increase after adding cellulose to sediments on day 90 of operation. On 160 day, maximum power density from the SMFC with adding 0.2% cellulose reached to 11.2 mW m⁻². In addition, the surface morphology of stainless steel anode on day 90 was analyzed by scanning electron microscope. It was found that the protection layer of the stainless steel as electrode in SMFCs was destroyed to some extent.     

A novel enzyme-immobilization method for a biofuel cell

Biofuel cells utilizing biocatalysts are attractive alternatives to metal catalyst-based cells because of environmentally friendly cells and their renewability and good operations at room temperatures, even though they provide a low level of electrical power. In this study, the effect of a novel enzyme immobilization method on anodic electrical properties was evaluated under ambient conditions for increasing the power of an enzyme-based biofuel cell. The anodic system employed in the cell contained a gold electrode, pyrroloquinoline quinone (PQQ) as the electron transfer mediator, lactate dehydrogenase (LDH), β-nicotinamide adenine dinucleotide (NAD⁺) as the cofactor, and lactate as the substrate. The anodic electrical properties increased as a result of the novel enzyme-immobilization method. Furthermore, lactate, NAD⁺, or CaCl₂, which can all influence enzyme activation, were used to prevent covalent bond formation near the active site of the LDH during enzyme-immobilization. Protection of the active site of the LDH using this novel enzyme-immobilization method increased its stability, which enabled to increase power production (142 μW/cm²) in a basic enzymatic fuel cell (EFC).     

Combustion of horse manure for heat production

The main objectives of this paper have been to evaluate the use of horse manure and wood-shavings as a fuel for heat production and to provide sets of data on the chemical composition, ash characteristics and ash forming elements of the fuel. Another objective has been to investigate the possibility to use the ash as fertiliser by analysing the heavy metal and nutrient contents. The results showed that the fuel is well suited for combustion for heat production causing low emissions of products of incomplete combustion. The emissions of NO_x were however high due to the high content of fuel bound nitrogen. Emissions of CO and NO_x were typically in the range of 30–150 mg/Nm³ and 280–350 mg/Nm³ at 10 vol% O₂, respectively. The analysis of the ash showed on sufficiently low concentration of heavy metals to allow recycling.     

A fuel cell model in biological energy conversion

Consideration of the high energy conversion efficiency of biological systems leads to the idea that mechanical energy may arise via a series of steps, of which a rate-determining one occurs in a fuel-cell-like element. The mitochondrion is suggested as the site of such entities. The observed efficiency would be consistent with a potential loss of about 0.5 V. The supposed biological fuel cells would be able to act as an electrical power source, driving chemical reactions against their spontaneous direction.Considerations of electrical conductance in wet proteins shows that ohmic (i.e., non-interfacial) potential differences through mitochondrial membranes could be negligible. The cathodic reaction would be the reduction of oxygen, O₂+4H⁺+4e^–H₂O and the anodic reaction, 2NADH⁺2NAD+2H⁺+4e^–. The anodes are suggested as being molecular, buried in the invaginations of the inner membrane forming the cristae. The cathodes are located on enzymes which are probably on the inner side of the membrane but could be, respectively, on the outer (cathodic), and the inner (anodic) sides. The electron transport occurs though proteins within each membrane. The relation of the so-called fuel cell potentials to potentially observable membrane potentials, and those measured by fluorescent probes, are discussed.The fuel cells produce electrical energy and this energy is transferred to ADP by an electrolytic route, using electric power from the cells to work the endergonic ATP synthesis. Possible electrode reactions are suggested. An exponential dependence of the rate of ATP synthesis upon applied potential has been observed.Biological cells radiate electromagnetically in the 10⁹ to 10¹⁵ Hz region. Such phenomena support a fuel cell model of a biological cell because they demand the presence of mobile electrons.     

Tensile loading characteristics of hydrogen stored carbon nanotubes in PEM fuel cell operating conditions using molecular dynamics simulation

Mechanical characteristics of hydrogen stored single walled carbon nanotube (SWCNT) in proton exchange membrane fuel cell (PEMFC) operating conditions are analysed in this work using molecular dynamics simulation method. The investigation of mechanical characteristics of hydrogen stored SWCNT is critical in determining the lifetime and stability of SWCNT-based membranes used in PEMFC. The study provides a comprehensive analysis on the effects of geometry, vacancy defects and PEMFC operating temperature on the mechanical properties of hydrogen stored SWCNT. The findings show that the mechanical strength of the hydrogen stored SWCNT can be enhanced by deploying a bigger armchair SWCNT. Furthermore, increase in operating temperature of PEMFC reduces the mechanical resistance of hydrogen stored SWCNT, which however can be overcome by suitably introducing vacancy defects in the SWCNT geometry. This has provided potential way of increasing the hydrogen storage capacity of SWCNT which is very useful for onboard application of PEMFC. It is anticipated that the findings obtained from this paper will have a paramount importance in the field of hydrogen energy fuel cell technology and further compliment the potential applications of SWCNTs as promising candidates for applications in fuel cells and energy storage devices.     

Population dynamics and current-generation mechanisms in cassette-electrode microbial fuel cells

Cassette-electrode microbial fuel cells (CE-MFCs) have been demonstrated useful to treat biomass wastes and recover electric energy from them. In order to reveal electricity-generation mechanisms in CE-MFCs, the present study operated a bench-scale reactor (1 l in capacity; approximately 1,000 cm² in anode and cathode areas) for treating a high-strength model organic wastewater (comprised of starch, peptone, and fish extract). Approximately 1 month was needed for the bench reactor to attain a stable performance, after which volumetric maximum power densities persisted between 120 and 150 mW/l throughout the experiment (for over 2 months). Temporal increases in the external resistance were found to induce subsequent increases in power outputs. After electric output became stable, electrolyte and anode were sampled from the reactor for evaluating their current-generation abilities; it was estimated that most of current (over 80%) was generated by microbes in the electrolyte. Cyclic voltammetry of an electrolyte supernatant detected several electron shuttles with different standard redox potentials at high concentrations (equivalent to or more than 100 μM 5-hydroxy-1,4-naphthoquinone). Denaturing gradient gel electrophoresis and quantitative real-time PCR of 16S ribosomal RNA gene fragments showed that bacteria related to the genus Dysgonomonas occurred abundantly in association with the increases in power outputs. These results suggest that mediated electron transfer was the main mechanism for electricity generation in CE-MFC, where high-concentration electron shuttles and Dysgonomonas bacteria played important roles.     

Archaea-based microbial fuel cell operating at high ionic strength conditions

In this work, two archaea microorganisms (Haloferax volcanii and Natrialba magadii) used as biocatalyst at a microbial fuel cell (MFC) anode were evaluated. Both archaea are able to grow at high salt concentrations. By increasing the media conductivity, the internal resistance was diminished, improving the MFC’s performance. Without any added redox mediator, maximum power (P _max) and current at P _max were 11.87/4.57/0.12 μW cm⁻² and 49.67/22.03/0.59 μA cm⁻² for H. volcanii, N. magadii and E. coli, respectively. When neutral red was used as the redox mediator, P _max was 50.98 and 5.39 μW cm⁻² for H. volcanii and N. magadii, respectively. In this paper, an archaea MFC is described and compared with other MFC systems; the high salt concentration assayed here, comparable with that used in Pt-catalyzed alkaline hydrogen fuel cells, will open new options when MFC scaling up is the objective necessary for practical applications.     

Performance of microbial fuel cell in response to change in sludge loading rate at different anodic feed pH

Performance of two dual chambered mediator-less microbial fuel cells (MFCs) was evaluated at different sludge loading rate (SLR) and feed pH. Optimum performance in terms of organic matter removal and power production was obtained at the SLR of 0.75 kg COD kg VSS⁻¹ d⁻¹. Maximum power density of 158 mW/m² and 600 mW/m² was obtained in MFC-1 (feed pH 6.0) and MFC-2 (feed pH 8.0), respectively. Internal resistance of the cell decreased with increase in SLR. When operated only with biofilm on anode, the maximum power density was 109.5 mW/m² in MFC-1 and 459 mW/m² in MFC-2, which was, respectively, 30% and 23.5% less than the value obtained in MFC-1 and MFC-2 at SLR of 0.75 kg COD kg VSS⁻¹ d⁻¹. Maximum volumetric power of 15.51 W/m³ and 36.72 W/m³ was obtained in MFC-1 and MFC-2, respectively, when permanganate was added as catholyte. Higher feed pH (8.0) favoured higher power production.