Synthesis and decoloring properties of sodium humate/poly (N-isopropylacrylamide) hydrogels

A series of novel sodium humate/poly(N-isopropylacrylamide) (SH/PNIPA) hydrogels were synthesized by solution polymerization. The swelling and decoloring properties of SH/PNIPA hydrogels were also examined. Experiment results show that there exist hydrogen-bonding interactions between SH and PNIPA in the SH/PNIPA hydrogels network, which are not strong enough to disrupt the aggregation of dehydrated PNIPA chains at phase transition temperature, leading to the same volume phase transition temperature as pure PNIPA hydrogel. The adsorption and desorption of methylene blue (MB) for the hydrogels were influenced by temperature, initial MB concentration and SH amount. Low temperature favors the adsorption and desorption of MB. Appropriate SH amount of the hydrogels is crucial for the adsorption and desorption of MB. The maximum adsorption capacity was 10.8 mg MB per gram of SH/PNIPA gel.     

Variable temperature FTIR study of poly(ethylene-co-vinyl alcohol)-graft-poly(epsilon-caprolactone)

A recently developed technique, i.e., two-dimensional infrared (2D IR) correlation spectroscopy, is used to study the thermal behavior of poly(ethylene-co-vinyl alcohol)-graft-poly(epsilon-caprolactone), a new synthesized highly grafted copolymer. The use of the 2D IR approach to analyze temperature-dependent spectra collected in situ during the temperature elevation process effectively enhanced the spectral resolution and revealed details on the hydrogen bonding and conformational change which are not easily detected in the traditional one-dimensional spectra. The sequence of the spectral changes of different OH and CH(2) fundamental vibrations during heating the polymer was inferred from the signs of the asynchronous peaks. Evidence that the conformational changes of the methylene groups precede the loosening of hydrogen bonds is provided.     

Intramolecular complex formation of poly(N-isopropylacrylamide) with human serum albumin

Complexation of human serum albumin (HSA) with poly(N-isopropylacrylamide) (PNIPA) ranging in molecular weight (M(PNIPA)) from 2.1 x 10(4) to 1.72 x 10(6) was studied in an aqueous system (pH 3) containing NaCl as a supporting salt. Dynamic light scattering, static light scattering, electrophoretic light scattering, and dialyzing techniques were used as the experimental tool in a suitable combination. The measurements were performed mainly at 25 degrees C and at 0.01 M NaCl as a function of mixing ratio (r(m), molar ratio of PNIPA to HSA). The results of DLS and ELS evidently demonstrated the formation of a water-soluble complex through mixing of HSA and PNIPA. A detailed analysis of SLS data with the aid of dialysis data revealed that the resulting complex is an "intramolecular" complex consisting of a PNIPA chain with several of bound HSA molecules. Both hydrodynamic radius (R(h)) and radius gyration (R(g)) of intramolecular complexes decreased as r(m) was increased. This result correlated well to the fact that the number (n) of bound proteins per polymer decreases with increasing r(m). The size and the molar mass of the complex became large depending on M(PNIPA), but the increase of M(PNIPA) led to a decrease in n at r(m) < 1. The increase in NaCl concentration from 0.01 to 0.3 M brought about the increase in the size and the molar mass of an intramolecular HSA-PNIPA complex prepared at r(m) = 1.1. This was found to be due to an increase of n. A similar trend was observed when temperature rose from 25 to 32 degrees C (close to lower critical solution temperature of PNIPA). However, the effect of temperature on the increase of was strong in comparison with that of ionic strength. On the basis of these results obtained, the complexation mechanism was discussed in detail.     

Hydroxylated poly(N-isopropylacrylamide) as functional thermoresponsive materials

In this study, we developed a poly(N-isopropylacrylamide)-based thermoresponsive polymeric material with a high content of hydroxyl groups. We newly designed the functional monomer, N-(2-hydroxyisopropyl)acrylamide (HIPAAm), considering maintaining the continuous and repeated structure of the isopropylamide group after copolymerization and the monomer reactivity ratios. The thermoresponsive polymer was derived by conventional radical copolymerization of HIPAAm with N-isopropylacrylamide (NIPAAm) in high yield. Estimation of monomer reactivity ratios, r(1) and r(2), supported the almost random sequence of the comonomers. The obtained copolymers showed a very sensitive phase transition and/or separation in response to temperature in aqueous media although they have many hydrophilic parts, and their thermoresponsive behavior was not affected by the pH. Furthermore, the cloud points of these copolymers closely depended on the HIPAAm content and could be easily controlled by adding salts. HIPAAm is expected to regulate the phase transition and/or separation temperature of the NIPAAm-based copolymers while maintaining their desirable sensitive thermoresponse. Differential scanning calorimetric analysis showed that dehydration of the polymer chains occurring in phase transition became incomplete with increasing HIPAAm content. Moreover, it was found that poly(NIPAAm-co-HIPAAm) having a high content of the HIPAAm unit showed liquid-liquid phase separation involving coacervation. The sizes of the coacervate droplets were relatively monodisperse and very minimal. Poly(NIPAAm-co-HIPAAm) is valuable for use in biomedical fields such as bioseparation.     

Amphiphilic core-shell nanoparticles with poly(ethylenimine) shells as potential gene delivery carriers

Spherical, well-defined core-shell nanoparticles that consist of poly(methyl methacrylate) (PMMA) cores and branched poly(ethylenimine) shells (PEI) were synthesized via a graft copolymerization of methyl methacrylate from branched PEI induced by a small amount of tert-butyl hydroperoxide. The PMMA-PEI core-shell nanoparticles were between 130 to170 nm in diameter and displayed zeta-potentials near +40 mV at pH 7 in 1 mM aqueous NaCl. Plasmid DNA (pDNA) was mixed with nanoparticles and formed complexes of approximately 120 nm in diameter and was highly monodispersed. The complexes were characterized with respect to their particle size, zeta-potential, surface morphology, and DNA integrity. The complexing ability of the nanoparticles was strongly dependent on the molecular weight of the PEI and the thickness of the PEI shells. The stability of the complexes was influenced by the loading ratio of the pDNA and the nanoparticles. The condensed pDNA in the complexes was significantly protected from enzymatic degradation by DNase I. Cytotoxity studies using MTT colorimetric assays suggested that the PMMA-PEI (25 kDa) core-shell nanoparticles were three times less toxic than the branched PEI (25 kDa). Their transfection efficiencies were also significantly higher. Thus, the PEI-based core-shell nanoparticles show considerable potential as carriers for gene delivery.     

Ruthenium(II) tris(bipyridine)-centered poly(ethylenimine) for gene delivery

Ruthenium(II) tris(bipyridine)-centered poly(ethylenimine) (Ru PEI) was synthesized via acid hydrolysis of Ru tris(bipyridine)-centered poly(2-ethyl-2-oxazoline) (Ru PEOX), and the luminescence, DNA entrapment, and transfection efficiencies were evaluated. Emission maxima for Ru PEI samples are red-shifted compared to Ru PEOX precursors, and the luminescence lifetimes are shorter in both methanol and aqueous solutions. Slower oxygen quenching of Ru PEOX and Ru PEI luminescence versus [Ru(bpy)3]Cl2 (bpy = bipyridine) is attributed to polymer shielding effects. Ru PEI luminescence is similar in the presence and absence of DNA. Ru PEI (7900 Da) and linear PEI (L-PEI; 22,000 Da) fully entrapped DNA (5.4 kb; pcDNA) at an N/P ratio of 2. LNCaP prostate cancer cells were transfected with a plasmid encoding for green fluorescent protein using Ru PEI and L-PEI vectors for comparison. For N/P = 48, the transfection efficiency for Ru PEI was approximately 50% relative to that of L-PEI.     

Stereoselectivity in deacylation of nitrophenyl acylates by poly(ethylenimine) derivatives

Deacylation of nitrophenyl acetates containing carboxyl substituents [4-acetoxy-3-nitrobenzoic acid (1), 3-acetoxy-4-nitrobenzoic acid (2), and 2-acetoxy-5-nitrobenzoic acid (3)] was studied in the presence of poly(ethylenimine) derivatives. The polymers examined contained lauryl groups (Lau₁₂PEI) or both lauryl and imidazolyl groups (Lau₁₂Im₁₀PEI). The reaction with active ester proceeds through the attack of primary amino groups of the polymers at the acyl carbons of the substrates. The reaction of Lau₁₂Im₁₀PEI with a hydrophobic ester, p-nitrophenyl caproate (NPC), however, has been reported to involve the attack by the imidazolyl group of the polymer. Thus, the anionic (carboxyl-containing) and the hydrophobic esters bind to different domains on Lau₁₂Im₁₀PEI. Among the anionic substrates, 3 has uniquely large k_cat values compared with 1 or 2. This is explained in terms of closer proximity between a nucleophile amino group of the polymer and the scissile bond of the substrate in the polymer-substrate complex.     

Synthesis of temperature-responsive heterobifunctional block copolymers of poly(ethylene glycol) and poly(N-isopropylacrylamide)

Heterobifunctional block copolymers of poly(ethylene glycol) (PEG) and poly(N-isopropylacrylamide) (PNIPAM) were synthesized by reversible addition-fragmentation chain transfer (RAFT) polymerization of NIPAM using a macromolecular trithiocarbonate PEG-based chain transfer agent. The polymerization showed all the expected features of living radical polymerization and allowed the synthesis of copolymers with different lengths of the PNIPAM block. The synthesized block copolymers contained a carboxylic acid group from L-lysine at the focal point and a trithiocarbonate group at the terminus of the PNIPAM block. The trithiocarbonate functionality was converted into a thiol group and used for conjugation of biotin to the end of the PNIPAM block. The copolymers exhibited temperature-dependent association behavior in aqueous solution with a phase transition of approximately 32 degrees C. The described heterobifunctional block copolymers show promise for surface modifications with the potential for stimulus-controlled surface presentation of ligands attached to the terminus of the PNIPAM block.     

Temperature-responsive size-exclusion chromatography using poly(N-isopropylacrylamide) grafted silica

Silica-based packing materials induce non-specific interactions with proteins in aqueous media because of the nature of their surface, mainly silanol groups. Therefore, the silica surface has to be modified in order to be used as stationary phase for the High Performance Size-Exclusion Chromatography (HPSEC) of proteins. For this purpose, porous silica beads were coated with hydrophilic polymer gels (dextrans of different molecular weights) carrying a calculated amount of diethylaminoethyl groups (DEAE). Actually, as shown by HPSEC, these dextran modified supports minimize non-specific adsorption for proteins and pullulans in aqueous solution. Then, in order to change the pore size in response to temperature, temperature responsive polymer of poly(N-isopropylacrylamide) (PIPAAm) was introduced into the surface of dextran-DEAE on porous silica beads. The structure of these supports before and after modification was alternately studied by Scanning Electronic Microscopy (SEM) and Scanning Force Microscopy (SFM). An adsorption of radiolabelled albumin was performed to complete our study. Silica modifications by dextran-DEAE and PIPAAm improve the neutrality of the support and minimize the non-specific interactions between the solid support and proteins in solution. At low temperature, the support having PIPAAm exhibits a high resolution domain in HPSEC and finally permits a better resolution of proteins and pullulans. At higher temperature, hydrophobic properties of PIPAAm produce interactions with some proteins and trigger off a slight delay of their elution time.     

Novel branched poly(ethylenimine)-cholesterol water-soluble lipopolymers for gene delivery

A novel water-soluble lipopolymer was synthesized by linking cholesteryl chloroformate to the secondary amino groups of branched poly(ethylenimine) (PEI) of 1,800 and 10,000 Da. Conjugation through PEI secondary amines gives this newly synthesized lipopolymer (abbreviated as PEI-Chol) special advantage over our previously synthesized lipopolymers, which utilized the primary amino groups for conjugation, as the primary amino groups have a significant role in DNA condensation. Also, significantly, only one cholesterol molecule was grafted onto each PEI molecule (confirmed by (1)H NMR and MALDI-TOF mass spectrometry), leaving enough space for the steric interactions of the PEI's primary amines with the DNA. The PEI-Chol lipopolymer was characterized for the critical micellar concentration (cmc), buffer capacity, DNA condensation (by band retardation and circular dichroism), in vitro transfection efficiency, and cell viability. The cmcs of PEI-Chol 1,800 and PEI-Chol 10,000 were 496.6 and 1,330.5 microg/mL, respectively. The acid-base titration indicated high buffering capacity of the polymers around the pH range of 5-7, which indicated their potential for buffering in the acidic pH environment of the endosomes. The band retardation studies indicated that efficient condensation of the plasmid DNA could be achieved using these lipopolymers. The circular dichroism spectra indicated a change in DNA conformation and adoption of lower energy state upon condensation with these lipopolymers when an N/P ratio of 2.5/1 or above was formulated. The mean particle size of these complexes was in the range 110-205 nm, except for the complexes prepared using PEI of 1,800 Da, which had a mean particle size of 384 +/- 300 nm. The zeta potential of DNA complexes prepared using PEI-Chol 1,800, PEI-Chol 10,000 and PEI of 1,800, 10,000, and 25,000 Da at an N/P ratio of 15/1 was in the range 23-30 mV and was dependent on the N/P ratios. The in vitro transfection of PEI-Chol/pCMS-EGFP complexes in Jurkat cells showed high levels of expressed Green Fluorescent Protein (GFP) with little toxicity as determined by flow cytometry. These novel water-soluble lipopolymers provided good transfection efficiency with other desirable characteristics such as water solubility, free primary amino groups for efficient DNA condensation and high buffer capacity that indicated the possibility of efficient endosomal release.     

RNA-like conformational properties of a synthetic DNA poly(dA-dU).poly(dA-dU)

Differences in the circular dichroism of poly(dA-dT).poly(dA-dT) and poly(dA-dU).poly(dA-dU) and in its temperature induced changes are reported. A comparison to the data obtained with DNA and RNA indicates that an absence of thymine methyl groups in the polynucleotide results in promoting its RNA-like conformational properties. However, poly(dA-dU).poly(dA-dU) is not an A-DNA type of double helix.     

Highly branched poly(N-isopropylacrylamide) for use in protein purification

Poly(N-isopropylacrylamide)s with imidazole endgroups were used to separate a histidine-tagged protein fragment directly from a crude cell lysate. The polymers display a lower critical solution temperature that can be tuned to occur at a range of subambient temperatures. UV-visible spectra indicated differences in the binding in aqueous media of Cu(II) and Ni(II) to the imidazole endgroups. These changes in the UV-visible spectra were reflected in the solution/aggregation behavior of the polymers as studied by dynamic light scattering. The addition of Cu(II) disaggregated the polymers, and the polymer coil swelled. On the other hand, when Ni(II) was added the polymers remained aggregated in aqueous media. The polymers were used to purify residues 230-534 of the histidine-tagged breast cancer susceptibility protein his6-BRCA1. Cu(II) was found to be better suited to the formation of useful polymer-metal ion-protein complexes that display cloud points, since Ni(II)/polymer mixtures generated very little purified protein. The polymers were synthesized using a previously reported variation of the reversible addition-fragmentation chain termination (RAFT) methodology, using the chain transfer agent 3H-imidazole-4-carbodithioic acid 4-vinyl benzyl ester with N-isopropylacrylamide (NIPAM).     

Reducible poly(amido ethylenimine)s designed for triggered intracellular gene delivery

Poly(amido ethylenimine) polymers, a new type of peptidomimetic polymer, containing multiple disulfide bonds (SS-PAEIs) designed to degrade after delivery of plasmid DNA (pDNA) into the cell were synthesized and investigated as new carriers for triggered intracellular gene delivery. More specifically, three SS-PAEIs were synthesized from Michael addition reactions between cystamine bisacrylamide (CBA) and three different ethylene amine monomers, i.e., ethylenediamine (EDA), diethylenetriamine (DETA), or triethylenetetramine (TETA). Complete addition reactions were confirmed by (1)H NMR. The molecular weight, buffer capacity, and relative degree of branching for each SS-PAEI was determined by gel permeation chromatography (GPC), acid-base titration, and liquid chromatography-mass spectroscopy (LC-MS), respectively. Physicochemical characteristics of polymer/pDNA complexes (polyplexes) were analyzed by gel electrophoresis, particle size, and zeta-potential measurements. All three SS-PAEIs effectively complex pDNA to form nanoparticles with diameters less than 200 nm and positive surface charges of approximately 32 mV. The in vitro gene transfer properties of SS-PAEIs were evaluated using mouse embryonic fibroblast cell (NIH3T3), primary bovine aortic endothelial cell (BAEC), and rat aortic smooth muscle cell (A7R5) lines. Interestingly, polyplexes based on all three SS-PAEIs exhibited remarkably high levels of reporter gene expression with nearly 20x higher transfection efficiency than polyethylenimine 25k. The high transfection efficiency was maintained in the presence of 10% serum in the transfection medium. Furthermore, confocal microscopy experiments using labeled pDNA indicated that polyplexes of SS-PAEI displayed greater intracellular distribution of pDNA as compared to PEI, most likely due to environmentally triggered release. Therefore, SS-PAEIs are a new class of transfection agents that facilitate high gene expression while maintaining a low level of toxicity.     

聚N-异丙基丙烯酰胺细胞培养平台的研究进展

聚N-异丙基丙烯酰胺(poly(N-isopropylacrylamide),PNIPAAm),温敏性聚合物,可利用其温敏特性替代酶类物质或细胞刮刀用于贴壁细胞的收获,从而有效避免酶解和机械损伤,可为生物医药领域提供品质优良的种子细胞。重点阐述促进细胞有效粘附和快速脱附的温敏性PNIPAAm二维平面的研发情况,包括选取特殊基材、引入亲水基团、调节反应物比率、控制聚合物厚度/密度、提供适宜外力等方式,从而有效改善细胞对温敏性平面的适应性并降低染菌风险以及减少低温处理对细胞的影响。同时介绍PNIPAAm微载体、支架和凝胶等温敏性三维培养介质的研究进展,此方式不仅增加细胞生长面积,更可以模拟体内微环境,从而保持细胞原始生理特征,同时实现大规模扩增和非酶解收获细胞以及组织器官修复和重构的目标。最后简单说明PNIPAAm培养平台的应用,PNIPAAm的研发为再生医学的发展提供了崭新思路。     

Stimuli-responsive zwitterionic block copolypeptides: poly(N-isopropylacrylamide)-block-poly(lysine-co-glutamic acid)

Synthesis of novel zwitterionic block copolypeptides, poly(N-isopropylacrylamide)-block-poly(L-glutamic acid-co-L-lysine) [PNiPAM(n)(PLG(x)-co-PLLys(y))m , where n is the number-average degree of polymerization (DP(n)) of PNiPAM block, x and y are the mole fraction of glutamic acid and lysine residues, respectively, and m is the total DP(n) of the peptide block], and their stimuli-responsiveness to temperature and pH variation in aqueous solutions are described. Initiated with the amino-terminated poly(N-isopropylacrylamide) (PNiPAM(n)-NH2), ring-opening polymerization (ROP) of a mixture of gamma-benzyl-L-glutamate N-carboxyanhydride (BLG-NCA), and Boc-L-lysine N-carboxyanhydride (BLLys-NCA) afforded the block copolypeptides PNiPAM(n)(PBLG(x)-co-PBLLys(y))m, with a poly(N-isopropylacrylamide) block together with a random copolypeptide block, which was then deprotected with HBr/trifluoroacetic acid into the double hydrophilic block copolypeptides, PNiPAM(n)(PLG(x)-co-PLLys(y))m. Their block ratios and lengths, as well as the amino acid residue ratios in the random copolypeptide block are varied (n = 360, x = 0.4-0.5, y = 0.4-0.6, and m = 220-252). The secondary structures of the copolypeptides in aqueous solution at different pH conditions were examined. Phase transitions in aqueous solutions induced by both pH and temperature variation were investigated by (1)H NMR spectroscopy. The transitions induced by temperature were also explored by turbidity measurements using UV/vis spectroscopy for their lower critical aggregation temperature (LCAT) determination. Furthermore, these aggregation processes were followed by dynamic light scattering measurements.     

Inner-sphere complexes of divalent cations with single-stranded poly(rA) and poly(rU)

A combination of ultrasound velocimetry, density, and UV spectroscopy has been employed to study the hydration effects of binding of Mn(2+) and alkaline-earth cations to poly(rA) and poly(rU) single strands. The hydration effects, obtained from volume and compressibility measurements, are positive due to overlapping the hydration shells of interacting molecules and consequently releasing the water molecules to bulk state. The volume effects of the binding to poly(rA), calculated per mole of cations, range from 30.6 to 40.6 cm(3) mol(-1) and the compressibility effects range from 59.2 x 10(-4) to 73.6 x 10(-4) cm(3) mol(-1) bar(-1). The volume and compressibility effects for poly(rU) are approximately 17 cm(3) mol(-1) and approximately 50 x 10(-4) cm(3) mol(-1) bar(-1), respectively. The comparative analysis of the dehydration effects suggests that the divalent cations bind to the polynucleotides in inner-sphere manner. In the case of poly(rU) the dehydration effects correspond to two direct coordination, probably between adjacent phosphate groups. The optical study did not reveal any effects of cation on the secondary structure or aggregation of poly(rU). In the case of single-helical poly(rA) binding is more specific: dehydration effects correspond to three to five direct contacts and must involve atomic groups of adenines, and the divalent cations stabilize and aggregate the polynucleotide.     

Sequence-specific affinity precipitation of oligonucleotide using poly(N-isopropylacrylamide)-oligonucleotide conjugate

In this study we develop a sequence-specific precipitation separation system of oligonucleotide (ODN) using a conjugate between poly(N-isopropylacrylamide) (PNIPAM) and ODN. PNIPAM is known as a thermoresponsive polymer and dehydrates to precipitate above its phase transition temperature in an aqueous milieu. The principal advantage of this separation system using the conjugate is that the hybridization reaction between the conjugate and oligonucleotide is conducted in homogeneous solution. The conjugate was prepared by copolymerization between N-isopropylacrylamide and a vinyl-derivatized (dT)(8). The obtained conjugate efficiently precipitated (dA)(8) from solution when the solution contained more than 1.5 M NaCl. The conjugate containing 3 nmol of (dT)(8) residue was able to precipitate 1.4 nmol of (dA)(8), suggesting that the (dT)(8) residue of the conjugate formed a triple helix with (dA)(8). From an equimolar mixture of (dA)(8) and its one point mutant, the conjugate selectively precipitated (dA)(8): the highest selectivity was obtained for the isolation of (dA)(8) from the mixture consisting of (dA)(4)dT(dA)(3) and (dA)(8). When the conjugate was applied for the precipitation of five oligo(dA)s having different chain lengths, the longer oligo(dA)s tended to be precipitated by the conjugate more efficiently than the shorter ones. The conjugate could be used repeatedly for precipitation of (dA)(8) without showing any loss in precipitation efficiency.     

Preparation and tumor cell uptake of poly(N-isopropylacrylamide) folate conjugates

Folate conjugates (PNIPAM-NH-FA) of a copolymer of N-isopropylacrylamide (NIPAM) and amino-N'-ethylenedioxy-bis(ethylacrylamide) were prepared by an efficient synthesis leading to random grafting, via a short dioxyethylene spacer, of approximately 7 folic acid residues per macromolecule. The chemical composition of the copolymer was characterized by (1)H NMR and UV/vis spectroscopy. A fluorophore-labeled folate PNIPAM conjugate was tested by in vitro assays performed with cultured KB-31 cells overexpressing the folate receptor. The cellular uptake of the copolymer was found to be temperature dependent and was competitively decreased by free folic acid, indicating that the polymer uptake is mediated specifically by the folate receptor. Hydrophobically modified folate conjugates of NIPAM, amino-N'-ethylenedioxy-bis(ethylacrylamide) copolymers, bearing a small number of n-octadecyl groups were prepared following a modified synthetic procedure for use in future studies of FA-targeted liposomes.     

Physicochemical characterization of thermoresponsive poly(N-isopropylacrylamide)-poly(ethylene imine) graft copolymers

Synthetic polycations have shown promise as gene delivery vehicles but suffer from an unacceptable toxicity and low transfection efficiency. Novel architectures are being explored to increase transfection efficiency, including copolymers with a thermoresponsive character. The physicochemical characterization of a family of copolymers comprising a core of the cationic polymer poly(ethylene imine) (PEI) with differing thermoresponsive poly( N-isopropylacrylamide) (PNIPAM) grafts has been carried out using pulsed-gradient spin-echo NMR (PGSE-NMR) and small-angle neutron scattering (SANS). For the copolymers that have longer chain PNIPAM grafts, there is clear evidence of the collapse of the grafts with increasing temperature and the associated emergence of an attractive interpolymer interaction. These facets depend on the number of PNIPAM grafts attached to the PEI core. While a collapse in the smaller PNIPAM grafts is observed for the third polymer, there is no appearance of the interpolymer attractive interaction. These observations provide further insight into the association behavior of these copolymers, which is fundamental to developing a full understanding of how they interact with nucleic acids. Furthermore, the differing behaviors of the three copolymers over temperatures in which the PNIPAM blocks undergo coil-to-globule transitions is indicative of changes in the presentation of charged-core and hydrophobic chain components, which are key factors affecting nucleic acid binding and, ultimately, cell transfection ability.