Effect of conductive polymers coated anode on the performance of microbial fuel cells (MFCs) and its biodiversity analysis

Conductive polymer, one of the most attractive electrode materials, has been applied to coat anode of MFC to improve its performance recently. In this paper, two conductive polymer materials, polyaniline (PANI) and poly(aniline-co-o-aminophenol) (PAOA) were used to modify carbon felt anode and physical and chemical properties of the modified anodes were studied. The power output and biodiversity of modified anodes, along with unmodified carbon anode were compared in two-chamber MFCs. Results showed that the maximum power density of PANI and PAOA MFC could reach 27.4 mW/m(2) and 23.8 mW/m(2), comparing with unmodified MFC, increased by 35% and 18% separately. Low temperature caused greatly decrease of the maximum voltage by 70% and reduced the sorts of bacteria on anodes in the three MFCs. Anode biofilm analysis showed different bacteria enrichment: a larger mount of bacteria and higher biodiversity were found on the two modified anodes than on the unmodified one. For PANI anode, the two predominant bacteria were phylogenetically closely related to Hippea maritima and an uncultured clone MEC_Bicarb_Ac-008; for PAOA, Clostridiales showed more enrichment. Compare PAOA with PANI, the former introduced phenolic hydroxyl group by copolymerization o-aminophenol with aniline, which led to a different microbial community and the mechanism of group effect was proposed.     

Electrochemical surface modification of carbon mesh anode to improve the performance of air-cathode microbial fuel cells

A convenient and promising alternative to surface modification of carbon mesh anode was fulfilled by electrochemical oxidation in the electrolyte of nitric acid or ammonium nitrate at ambient temperature. It was confirmed that such an anode modification method was low cost and effective not only in improving the efficiency of power generation in microbial fuel cells (MFCs) for synthetic wastewater treatment, but also helping to reduce the period for MFCs start-up. The MFCs with anode modification in electrolyte of nitric acid performed the best, achieving a Coulombic efficiency enhancement of 71 %. As characterized, the electrochemical modification resulted in the decrease of the anode potential and internal resistance but the increase of current response and nitrogen-containing and oxygen-containing functional groups on the carbon surface, which might contribute to the enhancement on the performances of MFCs.     

Effect of nitrogen addition on the performance of microbial fuel cell anodes

Carbon cloth anodes were modified with 4(N,N-dimethylamino)benzene diazonium tetrafluoroborate to increase nitrogen-containing functional groups at the anode surface in order to test whether the performance of microbial fuel cells (MFCs) could be improved by controllably modifying the anode surface chemistry. Anodes with the lowest extent of functionalization, based on a nitrogen/carbon ratio of 0.7 as measured by XPS, achieved the highest power density of 938 mW/m². This power density was 24% greater than an untreated anode, and similar to that obtained with an ammonia gas treatment previously shown to increase power. Increasing the nitrogen/carbon ratio to 3.8, however, decreased the power density to 707 mW/m². These results demonstrate that a small amount of nitrogen functionalization on the carbon cloth material is sufficient to enhance MFC performance, likely as a result of promoting bacterial adhesion to the surface without adversely affecting microbial viability or electron transfer to the surface.     

Microorganism-immobilized carbon nanoparticle anode for microbial fuel cells based on direct electron transfer

A fast and convenient bacterial immobilization method was proposed as an attempt to improve the anode efficiency of a microbial fuel cell, in which bacteria were entrapped into carbon nanoparticle matrix. The direct electron transfer from the entrapped bacterial cells to the anode was verified using cyclic voltammogram (CV). Using the immobilized bioanode, the start-up time of the MFC was greatly reduced. Meanwhile, the maximum power density of 1,947 mW m⁻² with the modified anode was much higher than that with the biofilm-based carbon cloth anode (1,479 mW m⁻²). Impedance measurements suggested that performance improvement resulted from the decrease in charge transfer and diffusion resistances. The results demonstrated that bacteria immobilization using carbon nanoparticle matrix was a simple and efficient approach for improving the anodes performances in MFCs.     

Air-cathode structure optimization in separator-coupled microbial fuel cells

Microbial fuel cells (MFC) with 30% wet-proofed air cathodes have previously been optimized to have 4 diffusion layers (DLs) in order to limit oxygen transfer into the anode chamber and optimize performance. Newer MFC designs that allow close electrode spacing have a separator that can also reduce oxygen transfer into the anode chamber, and there are many types of carbon wet-proofed materials available. Additional analysis of conditions that optimize performance is therefore needed for separator-coupled MFCs in terms of the number of DLs and the percent of wet proofing used for the cathode. The number of DLs on a 50% wet-proofed carbon cloth cathode significantly affected MFC performance, with the maximum power density decreasing from 1427 to 855 mW/m² for 1–4 DLs. A commonly used cathode (30% wet-proofed, 4 DLs) produced a maximum power density (988 mW/m²) that was 31% less than that produced by the 50% wet-proofed cathode (1 DL). It was shown that the cathode performance with different materials and numbers of DLs was directly related to conditions that increased oxygen transfer. The coulombic efficiency (CE) was more affected by the current density than the oxygen transfer coefficient for the cathode. MFCs with the 50% wet-proofed cathode (2 DLs) had a CE of >84% (6.8 A/m²), which was substantially larger than that previously obtained using carbon cloth air-cathodes lacking separators. These results demonstrate that MFCs constructed with separators should have the minimum number of DLs that prevent water leakage and maximize oxygen transfer to the cathode.     

Electricity generation from real industrial wastewater using a single-chamber air cathode microbial fuel cell with an activated carbon anode

This study introduces activated carbon (AC) as an effective anode for microbial fuel cells (MFCs) using real industrial wastewater without treatment or addition of external microorganism mediators. Inexpensive activated carbon is introduced as a proper electrode alternative to carbon cloth and carbon paper materials, which are considered too expensive for the large-scale application of MFCs. AC has a porous interconnected structure with a high bio-available surface area. The large surface area, in addition to the high macro porosity, facilitates the high performance by reducing electron transfer resistance. Extensive characterization, including surface morphology, material chemistry, surface area, mechanical strength and biofilm adhesion, was conducted to confirm the effectiveness of the AC material as an anode in MFCs. The electrochemical performance of AC was also compared to other anodes, i.e., Teflon-treated carbon cloth (CCT), Teflon-treated carbon paper (CPT), untreated carbon cloth (CC) and untreated carbon paper (CP). Initial tests of a single air-cathode MFC display a current density of 1792 mAm⁻², which is approximately four times greater than the maximum value of the other anode materials. COD analyses and Coulombic efficiency (CE) measurements for AC-MFC show the greatest removal of organic compounds and the highest CE efficiency (60 and 71%, respectively). Overall, this study shows a new economical technique for power generation from real industrial wastewater with no treatment and using inexpensive electrode materials.

     

Layer-by-layer construction of graphene-based microbial fuel cell for improved power generation and methyl orange removal

Development of highly efficient anode is critical for enhancing the power output of microbial fuel cells (MFCs). The aim of this work is to investigate whether modification of carbon paper (CP) anode with graphene (GR) via layer-by-layer assembly technique is an effective approach to promote the electricity generation and methyl orange removal in MFCs. Using cyclic voltammetry and electrochemical impedance spectroscopy, the GR/CP electrode exhibited better electrochemical behavior. Scanning electron microscopy results revealed that the surface roughness of GR/CP increased, which was favorable for more bacteria to attach to the anode surface. The MFCs equipped with GR/CP anode achieved a stable maximum power density of 368 mW m^?2 under 1,000 Ω external resistance and a start time for the initial maximum voltage of 180 h, which were, respectively, 51 % higher and 31 % shorter than the corresponding values of the MFCs with blank anode. The anode and cathode polarization curves revealed negligible difference in cathode potentials but obviously difference in anode potentials, indicating that the GR-modified anode other than the cathode was responsible for the performance improvement of MFC. Meanwhile, compared with MFCs with blank anode, 11 % higher decolorization efficiency and 16 % higher the chemical oxygen demand removal rate were achieved in MFC with GR-modified anode during electricity generation. This study might provide an effective way to modify the anode for enhanced electricity generation and efficient removal of azo dye in MFCs.     

Improving the power generation of microbial fuel cells by modifying the anode with single-wall carbon nanohorns

Objectives

To increase the power generation of microbial fuel cells (MFCs), anode modification with carbon materials (activated carbon, carbon nanotubes, and carbon nanohorns) was investigated.

Results

Maximum power densities of a stainless-steel anode MFC with a non-modified electrode (SS-MFC), an activated carbon-modified electrode (AC-MFC), a carbon nanotube-modified electrode (CNT-MFC) and a carbon nanohorn-modified electrode (CNH-MFC) were 72, 244, 261 and 327 mW m^?2, respectively. The total polarization resistance measured by electrochemical impedance spectroscopy were 3610 Ω for SS-MFC, 283 Ω for AC-MFC, 231 Ω for CNTs-MFC, and 136 Ω for CNHs-MFC, consistent with the anode resistances obtained by fitting the anode polarization curves.

Conclusions

Single-wall carbon nanohorns are better than activated carbon and carbon nanotubes as a new anode modification material for improving anode performance.

     

Increased sustainable electricity generation in up-flow air-cathode microbial fuel cells

Sustainable electricity was generated from glucose in up-flow air-cathode microbial fuel cells (MFCs) with carbon cloth cathode and carbon granular anode. Plastic sieves rather than membrane were used to separate the anode and cathode. Based on 1g/l glucose as substrate, a maximum volumetric power density of 25+/-4 W/m(3) (89 A/m(3)) was obtained for the MFC with a sieve area of 30 cm(2) and 49+/-3 W/m(3) (215 A/m(3)) for the MFC with a sieve area of 60 cm(2). The increased power density with larger sieve area was mainly due to the decrease of internal resistance according to the electrochemistry impedance spectroscopy analysis. Increasing the sieve area from 30 cm(2) to 60 cm(2) resulted in a decrease of overall internal resistance from 41 ohm to 27.5 ohm and a decrease of ohmic resistance from 24.3 ohm to 14 ohm. While increasing operational recirculation ratio (RR) decreased internal resistance and increased power output at low substrate concentration, the effect of RR on cell performance was negligible at higher substrate concentration.     

Performance and microbial ecology of air-cathode microbial fuel cells with layered electrode assemblies

Microbial fuel cells (MFCs) can be built with layered electrode assemblies, where the anode, proton exchange membrane (PEM), and cathode are pressed into a single unit. We studied the performance and microbial community structure of MFCs with layered assemblies, addressing the effect of materials and oxygen crossover on the community structure. Four MFCs with layered assemblies were constructed using Nafion or Ultrex PEMs and a plain carbon cloth electrode or a cathode with an oxygen-resistant polytetrafluoroethylene diffusion layer. The MFC with Nafion PEM and cathode diffusion layer achieved the highest power density, 381 mW/m² (20 W/m³). The rates of oxygen diffusion from cathode to anode were three times higher in the MFCs with plain cathodes compared to those with diffusion-layer cathodes. Microsensor studies revealed little accumulation of oxygen within the anode cloth. However, the abundance of bacteria known to use oxygen as an electron acceptor, but not known to have exoelectrogenic activity, was greater in MFCs with plain cathodes. The MFCs with diffusion-layer cathodes had high abundance of exoelectrogenic bacteria within the genus Geobacter. This work suggests that cathode materials can significantly influence oxygen crossover and the relative abundance of exoelectrogenic bacteria on the anode, while PEM materials have little influence on anode community structure. Our results show that oxygen crossover can significantly decrease the performance of air-cathode MFCs with layered assemblies, and therefore limiting crossover may be of particular importance for these types of MFCs.     

Effect of different acclimation methods on the performance of microbial fuel cells using phenol as substrate

Single-chamber microbial fuel cells (MFCs) with air-cathode were constructed. MFCs were fed different feedstocks during their inoculation, their role on phenol degradation and MFC performance were investigated. The results showed that the MFC inoculated using glucose exhibited the highest power density (31.3 mW m^?2) when phenol was used as the sole substrate for MFC. The corresponding biodegradation kinetic constant was obtained at 0.035 h^?1, at an initial phenol concentration of 600 mg L^?1. Moreover, the phenol degradation rates in this MFC with closed circuit were 9.8–16.5 % higher than those in MFC with opened circuit. The cyclic voltammograms revealed a different electrochemical activity of the anode biofilms in the MFC, and this led to differences in performance of the MFCs with phenol as sole substrate. These results demonstrated that phenol degradation and power production are affected by current generation and type of acclimation.     

Improved performance of membrane free single-chamber air-cathode microbial fuel cells with nitric acid and ethylenediamine surface modified activated carbon fiber felt anodes

Surface modifications of anode materials are important for enhancing power generation of microbial fuel cell (MFC). Membrane free single-chamber air-cathode MFCs, MFC-A and MFC-N, were constructed using activated carbon fiber felt (ACF) anodes treated by nitric acid and ethylenediamine (EDA), respectively. Experimental results showed that the start-up time to achieve the maximum voltages for the MFC-A and MFC-N was shortened by 45% and 51%, respectively as compared to that for MFC-AT equipped with an unmodified anode. Moreover, the power output of MFCs with modified anodes was significantly improved. In comparison with MFC-AT which had a maximum power density of 1304 mW/m², the MFC-N achieved a maximum power density of 1641 mW/m². The nitric acid-treated anode in MFC-A increased the power density by 58% reaching 2066 mW/m². XPS analysis of the treated and untreated anode materials indicated that the power enhancement was attributable to the changes of surface functional groups.     

石墨烯-多壁碳纳米管复合材料协同刃天青修饰阳极对微生物燃料电池性能的影响

【目的】利用石墨烯与多壁碳纳米管复合材料协同刃天青修饰微生物燃料电池(Microbial fuel cell,MFC)阳极,提高MFC的运行性能。【方法】以碳布为基底,采用滴涂法分别制备了刃天青/碳布(R/CC)、刃天青+石墨烯/碳布(R+GNS/CC)、刃天青+多壁碳纳米管/碳布(R+MWCNT/CC)、刃天青+石墨烯+多壁碳纳米管/碳布(R+GNS+MWCNT/CC)四种阳极材料。【结果】在降解高氯酸盐的过程中,与刃天青/碳布(最高输出电压54 m V)相比,刃天青+石墨烯/碳布、刃天青+多壁碳纳米管/碳布和刃天青+石墨烯+多壁碳纳米管/碳布阳极MFC最高输出电压分别为87、145、275 m V,分别提高了61.11%、168.52%、409.26%;高氯酸盐的还原速率也分别提高了59.1%、89.7%、147.3%。4种阳极的电化学交流阻抗(EIS)和塔菲尔(Tafel)测试发现,与刃天青/碳布阳极相比,刃天青+石墨烯/碳布、刃天青+多壁碳纳米管/碳布阳极活化内阻减小,电极反应速率提高,但刃天青+石墨烯+多壁碳纳米管/碳布阳极的活化内阻更小,电极反应速率更快,同时4种阳极附着微生物胞外聚合物(EPS)分析表明,修饰过的阳极附着微生物数量增加,多糖减少,R+GNS+MWCNT/CC阳极变化最大,更有利于微生物传递电子。【结论】石墨烯、多壁碳纳米管复合材料协同刃天青修饰MFC阳极可以减小活化内阻从而加快电子传递,进而提高MFC的性能。     

Power generation from cellulose using mixed and pure cultures of cellulose-degrading bacteria in a microbial fuel cell

Microbial fuel cells (MFCs) have been used to generate electricity from various organic compounds such as acetate, glucose, and lactate. We demonstrate here that electricity can be produced in an MFC using cellulose as the electron donor source. Tests were conducted using two-chambered MFCs, the anode medium was inoculated with mixed or pure culture of cellulose-degrading bacteria Nocardiopsis sp. KNU (S strain) or Streptomyces enissocaesilis KNU (K strain), and the catholyte in the cathode compartment was 50mM ferricyanide as catholyte. The power density for the mixed culture was 0.188mW (188mW/m(2)) at a current of 0.5mA when 1g/L cellulose was used. However, the power density decreased as the cellulose concentration in the anode compartment decreased. The columbic efficiencies (CEs) ranged from 41.5 to 33.4%, corresponding to an initial cellulose concentration of 0.1-1.0g/L. For the pure culture, cellobioase enzyme was added to increase the conversion of cellulose to simple sugars, since electricity production is very low. The power densities for S and K strain pure cultures with cellobioase were 162mW/m(2) and 145mW/m(2), respectively. Cyclic voltammetry (CV) experiments showed the presence of peaks at 380, 500, and 720mV vs. Ag/AgCl for the mixed bacterial culture, indicating its electrochemical activity without an external mediator. Furthermore, this MFC system employs a unique microbial ecology in which both the electron donor (cellulose) and the electron acceptor (carbon paper) are insoluble.     

Comparison of membrane- and cloth-cathode assembly for scalable microbial fuel cells: Construction,performance and cost

The aim of this study is to compare the performance of different membrane cathode assembly (MCA) and cloth-cathode assembly (CCA) in air-chamber microbial fuel cells (MFCs) and provide an optimum cathode configuration for MFC scaling up. Two MCAs were prepared by hot-pressing carbon cloth containing cathodic catalyst to anion exchange membrane (AEM) and cation exchange membrane (CEM), respectively. A CCA was built by coating GORE-TEX^® cloth with a mixture of nickel-based conductive paint and cathodic catalyst. Under the fed-batch mode using brewery wastewater, the MFCs were compared with respect to power production, coulombic efficiency, COD removal, internal resistance and material cost. The experimental results show that CCA is a more favorable alternative than MCAs due to its easier preparation, higher maximum power density and COD removal, and lower internal resistance and cost. The optimum cathode assembly of CCA is cost-effective and mechanically robust enough to meet the important requirements for MFC scalability.     

Comparison of anode bacterial communities and performance in microbial fuel cells with different electron donors

Microbial fuel cells (MFCs) harness the electrochemical activity of certain microbes for the production of electricity from reduced compounds. Characterizations of MFC anode biofilms have collectively shown very diverse microbial communities, raising ecological questions about competition and community succession within these anode-reducing communities. Three sets of triplicate, two-chamber MFCs inoculated with anaerobic sludge and differing in energy sources (acetate, lactate, and glucose) were operated to explore these questions. Based on 16S rDNA-targeted denaturing gradient gel electrophoresis (DGGE), all anode communities contained sequences closely affiliated with Geobacter sulfurreducens (>99% similarity) and an uncultured bacterium clone in the Bacteroidetes class (99% similarity). Various other Geobacter-like sequences were also enriched in most of the anode biofilms. While the anode communities in replicate reactors for each substrate generally converged to a reproducible community, there were some variations in the relative distribution of these putative anode-reducing Geobacter-like strains. Firmicutes were found only in glucose-fed MFCs, presumably serving the roles of converting complex carbon into simple molecules and scavenging oxygen. The maximum current density in these systems was negatively correlated with internal resistance variations among replicate reactors and, likely, was only minimally affected by anode community differences in these two-chamber MFCs with high internal resistance.     

Carbon nanotube supported MnO₂ catalysts for oxygen reduction reaction and their applications in microbial fuel cells

Three types of manganese dioxide, α-MnO(2), β-MnO(2), γ-MnO(2) were tested as alternative cathode catalysts for oxygen reduction reaction (ORR) in air-cathode microbial fuel cells (MFCs). Prepared by solution-based methods, the MnO(2) nanomaterials were comprehensively characterized, and their electrocatalytic activities in neutral electrolyte were investigated with the supporting material of carbon nanotubes (CNTs) by cyclic voltammetry (CV). The CV results showed that all MnO(2) species could catalyze ORR in neutral NaCl solution with different catalytic activities. β-MnO(2) had the highest catalytic activity due to its intrinsic structure and better interaction with CNTs. Three MnO(2) species were further used as cathode catalysts under optimized conditions in air-cathode cubic MFCs, in which mixed culture was inoculated as biocatalysts and domestic wastewater was used as the substrate in the anode chamber. It was also found that β-MnO(2) based MFC yielded the best performance with a power density of 97.8 mWm(-2) which was 64.1% that of the Pt-based MFC, and a lower internal resistance of 165 Ω. Furthermore, the COD removal efficiency of β-MnO(2) based MFC was estimated as 84.8%, higher than that of the Pt-based MFC. This study demonstrated that using β-MnO(2) on CNT support instead of Pt could potentially improve the feasibility of scaling up air-cathode MFCs for practical applications by lowering the material cost.     

Biocathode microbial fuel cell for efficient electricity recovery from dairy manure

Microbial fuel cells (MFCs) represent a new biological method for generating electricity directly from biodegradable compounds. Efficiency of MFCs using manure as substrate is generally low. This study proposed a new design by incorporating biocathodes into a three-chamber MFC, which yielded maximum power densities much higher than those reported in literature. The new design placed cylindrical anode chamber for easy stirring and two symmetrical cathodic chambers with reduced anode-cathode distance. The biocathodes were applied to reduce charge transfer resistance. Additionally, biocathode microbial community was cultured to enrich favorable microorganisms. With external loading of 100 Ω, the power densities for new biocathode MFC using 2, 4, 6, 8 and 10% total solids diary manure reached 7.85±1.0 W m(-3), 7.84±1.20 W m(-3), 8.15±0.20 W m(-3), 7.60±0.97 W m(-3) and 5.63±0.97 W m(-3), respectively. The pH drop as a result of manure hydrolysis limited the power output. To provide detailed information of the microbial community in the biocathode MFC, the 454-pyrosequencing technique was adopted. The Firmicutes, γ-, β-, α- and δ-Proteobacteria, Bacteroidetes and Actinobacteria were the major groups on the anode, while γ-, β-, and α-Proteobacteria, Bacteroidetes and Actinobacteria were the predominant groups on the cathode.     

The effect of physico-chemically immobilized methylene blue and neutral red on the anode of microbial fuel cell

A fast and cost effective immobilization of electron carriers, methylene blue (MB) and neutral red (NR) by pH shift was proposed to improve bioanodic performance. The adsorption of mediators onto the carbon cloth anode was verified using cyclic voltammogram (CV) and the effect of the immobilized mediators on acclimation, power density, and acetate removal of MFCs was investigated. A peak power density of P _max(MB) = 11.3 W/m³ was achieved over days 110 ∼ 120, as compared to P _max(Control) = 5.4 W/m³ and P _max(NR) = 3.1 W/m³ for the treated anode after 15 sequential fed-batch operations. The VFA removal rates however were similar for all MFC systems, ranging from 82 to 87%. It could be suggested that the increase in power density for the MB treated electrode resulted from an enhanced electron transport from exo-electrogenic bacteria. MB may also have a selective effect on the bacterial community during the start-up stage, increasing the voltage production and acetate removal from day 1 to 16. However, MFC with NR treated anode produced an initial voltage under 100 mV, with lower coulombic efficiency (CE). NR exhibited less favourable mediator molecule binding to the electrode surface, when subject to pH driven physico-chemical immobilization.     

Carbon nanotube powders as electrode modifier to enhance the activity of anodic biofilm in microbial fuel cells

Carbon nanotube (CNT) is a promising electrode material and has been used as an anode modifier in microbial fuel cells (MFCs). In this study, a new method of simultaneously adding CNT powders and Geobacter sulfurreducens into the anode chamber of a MFC was used, aiming to form a composite biofilm on the anode. The performance of MFCs such as startup time and steady-state power generation was investigated under conditions of different CNT powders dosages. Results showed that both the startup time and the anodic resistance were reduced. The optimal dosage of CNT powders pre-treated by acid was 4 mg/mL for the anode chamber with an effective volume of 25 mL. The anodic resistance and output voltage of the MFC with CNT powders addition were maintained around 180 Ω and 650 mV during 40 days operation, while those of the MFC without CNT powders addition increased from 250 Ω to 540 Ω and decreased from 630 mV to 540 mV, respectively, demonstrating that adding CNT powders helped stabilize the anodic resistance, thus the internal resistance and power generation during long-term operation. Based on cyclic voltammogram, the electrochemical activity of anodic biofilm was enhanced by adding CNT powders, though no significant increase of the biomass in anodic biofilm was detected by phospholipids analysis. There was no remarkable change of ohmic resistance with an addition of CNT powders revealed by current interrupt method, which indicated that the rate of mass transfer might be promoted by the presence of CNT powders.