Influence of asynchronous actuation of the Angara-5-1 facility modules on the penetration of the magnetic field inside a wire array

The influence of asynchronous actuation of the Angara-5-1 facility modules on the implosion symmetry of the wire array plasma in the Z-pinch mode is studied. It is shown that an increase in the r.m.s. jitter in the start times of the modules leads to an appreciable azimuthal asymmetry of magnetic field penetration inside the wire array and, as a consequence, to an increase in the duration of the soft X-ray pulse, a decrease in its power, and a shift of the Z-pinch with respect to the array axis. Necessary conditions for axisymmetric pinch implosion are determined. Experimental data on the magnitude and azimuthal distribution of the current (magnetic field) inside the wire array were obtained from magnetic probe measurements. The position of the Z-pinch with respect to the wire array axis was determined from two-dimensional X-ray images and radial optical streak images.     

Experiments on the implosion of heterogeneous wire arrays on the S-300 facility

Results are presented from experiments on the implosion of simple and nested wire arrays of different mass and material composition (W and/or Al). The experiments were performed on the S-300 facility (a high-current pulsed power generator with a voltage pulse amplitude of 700 kV, current amplitude of 2.5–3.5 MA, and pulse duration of 100 ns) at the Kurchatov Institute (Moscow). The imploding arrays were recorded using five-frame laser shadowgraphy, three-frame image-tube photography, an optical streak camera, X-ray pinhole cameras with different filters, X-ray polychromator, and X-ray spectrometer on the basis of a convex mica crystal. Laser probing measurements indicate that the current-carrying structure undergoes a fast (over a time shorter than 10 ns) global rearrangement, which manifests itself as the emergence of transparent regions. This effect is presumably related to the grouping of the wires, which carry currents of a few tens of kiloamperes, or to the current filamentation in their common plasma corona. The radiation of liners of different chemical composition in the final compressed state has been investigated. Electric measurements performed in experiments with nested arrays (e.g., with an aluminum outer liner and a tungsten inner liner) indicate that the inner array, which is still at rest, intercepts the electric current from the outer array when the latter penetrates through it. The effect of the “fall” of the outer liner through the inner one in the course of magnetic implosion has been revealed for the first time by analyzing X-ray emission spectra.     

Hard X-ray emission from imploding wire arrays

Results are presented from experimental studies of the generation of hard X-ray (HXR) emission with photon energies above 20 keV during the implosion of wire arrays in the Angara-5-1 facility. An analysis of X-ray images of the Z-pinch shows that the dimensions and spatial structures of the emitting regions are different for hard and soft X rays. It is found that the HXR emission peak is delayed with respect to the soft X-ray (SXR) one. The dependence of the HXR power on the material, initial diameter, and mass (implosion time) of the wire array is determined. It is shown that the HXR intensity in the spectral range >50 keV is several orders higher than the emission intensity in the high-energy tail of the SXR spectrum (assuming that this spectrum is thermal). A comparison of the time evolution and spatial localization of the HXR and SXR sources during the implosion of wire arrays indicates the presence of a new superthermal phenomenon that differs qualitatively from the processes determining the peak power of the SXR pulse. Possible mechanisms that can be responsible for the generation of HXR pulses are considered.     

Spatiotemporal behavior of X-ray emission above 20 keV from a Z-pinch produced by wire-array implosion

Results are presented from experimental studies of hard X-ray (HXR) emission in the photon energy range above 20 keV from dense radiating Z-pinch plasmas. The work is aimed at revealing the nature of fast-electron (electron beam) generation during the implosion of cylindrical and conical wire arrays in the Angara-5-1 facility at currents of up to 3 MA. It is found that the plasma implosion zippering caused by the inclination of wires affects the parameters of the HXR pulse emitted during the implosion of a conical array. It is shown that HXR emission correlates well with the decay of the plasma column near the cathode in the stagnation phase. HXR images of the pinch are produced by the bremsstrahlung of fast electrons generated during plasma column decay and interacting with plasma ions and the anode target. It is found that the use of conical arrays makes it possible to control the direction of plasma implosion zippering and the spatiotemporal and energy parameters of the pinch X-ray emission, in particular the X-ray yield. For wire array with diameters of 12 mm and linear masses of 200–400 μg/cm, the current of the fast electron beam is 20 kA and its energy is 60 J, which is about 1/500 of the energy of the main soft X-ray pulse.     

Studies of the distribution of the Z-pinch radiance during the implosion of wire arrays in the angara-5-1 facility

Results are presented from time-integrated measurements of soft X-ray emission from Z-pinches during the implosion of simple and nested wire arrays. The blackening density distribution obtained with the help of a pinhole camera is recalculated into the time-integrated Z-pinch radiance. It is found that, in the case of a simple wire array, up to 70% of the total SXR energy emitted during a discharge is radiated from the axial region, the rest of energy being radiated from plasma jets, whereas in the case of a nested wire array, more than 90% of the SXR energy is radiated from the axial region.     

Study of the core-corona structure formed during the explosion of an aluminum wire in vacuum

The time evolution of the matter parameters and current distribution in the discharge channel formed during a nanosecond explosion of a 25-μm-diameter 12-mm-long aluminum wire was studied in a series of experiments with the following parameters: the discharge voltage was U ₀ = 20 kV, the current amplitude was I _max ∼ 8 kA, and the current rise rate was dI/dt ∼ 40 A/ns. Optical shadow and schlieren images of the discharge channel were obtained using the second harmonic of a YAG: Nd⁺³ laser, and UV images of the discharge channel self-radiation were recorded using a four-frame camera with a microchannel plate. The process of aluminum wire explosion was simulated numerically (including simulations performed from the “cold start”). The numerical results were compared with the experimental data.     

Specific features of the structure of the Z-pinch emitting region formed during the implosion of a foam-wire load at the ANGARA-5-1 facility

Results are presented from experimental studies of the structure of the compressed plasma of a Z-pinch produced during the implosion of a foam-wire load at the current of up to 3 MA. The foam-wire load consisted of two nested cylindrical cascades, one of which was a solid or hollow cylinder made of low-density agar-agar foam, while the other was a wire array. The wall thickness of a hollow foam cylinder was 100–200 μm. The images of the pinch and its spectrum obtained with the help of multiframe X-ray cameras and a grazing incidence spectrograph with a spatial resolution were analyzed. Data on the spatial structure of the emitting regions and the soft X-ray (SXR) spectrum of the Z-pinch in the final stage of compression of a foam-wire load were obtained. The implosion modes characterized by the formation of hot regions during implosion of such loads were revealed. The characteristic scale lengths of the hot regions were determined. It is shown that the energy distribution of SXR photons in the energy range from 80 eV to 1 keV forms the spatial structure of Z-pinch images recorded during the implosion of foam-wire loads. It is revealed that the spectral density of SXR emission in the photon energy range of 300–600 eV from hot Z-pinch regions exceeds the spectral density of radiation from the neighboring Z-pinch regions by more than one order of magnitude. Groups of lines related to the absorption and emission of radiation by atoms and multicharged ions of carbon and oxygen in the outer foam cascade of a foam-wire load were recorded for the first time by analyzing the spatial distribution of the SXR spectra of multicharged ions of the Z-pinch. The groups of absorption lines of ions (C III, O III, O IV, and O VI) corresponding to absorption of SXR photons in the Z-pinch of a tungsten wire array, which served as the inner cascade of a foam-wire load, were identified. The plasma electron temperature measured from the charge composition of carbon and oxygen ions in the outer agar-agar foam cascade was 10–40 eV. During the implosion of foam-wire loads at currents of up to 3 MA, SXR pulses (hν > 100 eV) with a duration of 10 ns and peak power of 3 TW were detected. It is shown that the temporal profile of single-peak and double-peak SXR pulses can be controlled by varying the parameters of the outer and inner cascades of the foam-wire load.     

Investigation of the mechanism for current switching from the outer gas puff to the inner wire array in a structured Z-pinch

Experiments are reported on the implosion of structured loads with outer argon, krypton, and xenon gas puffs and an inner tungsten multiwire array. Experiments were carried out in the GIT-12 generator with a current of 2.6 MA and a current rise time of 270 ns. It is shown that the current successfully switches to the wire array only when the gas puff is sufficiently light. The total implosion time is 300 ns, and the implosion time of a wire array, determined from streak camera images, is 50–70 ns. It is suggested that the switching is efficient only when the active impedance of the gas puff is higher than the transitional resistance of the electrically exploded wires.     

Neutron emission during the implosion of a wire array onto a deuterated fiber

Results are presented from Z-pinch experiments performed in the S-300 facility (Kurchatov Institute) at a maximum current of 2 MA and current rise time of 100 ns. The Z-pinch load was a 1-cm-long 1-cmdiameter cylindrical array made of 40 tungsten wires with a total mass of 160 μg, at the axis of which a 100-μm-diameter (CD₂) _n deuterated fiber was installed. Hard X-ray and neutron signals were recorded using five scintillation detectors oriented in one radial and two axial directions. The maximum neutron yield from the DD reaction reached 3 × 10⁹ neutrons per shot. The average neutron energy was determined from time-of-flight measurements and Monte Carlo simulations under the assumption that the neutron emission time was independent of the neutron energy. The average neutron energy in different experiments was found to vary within the range 2.5–2.7 MeV. The fact that the average neutron energy was higher than 2.45 MeV (the energy corresponding to the DD reaction) is attributed to the beam-target collisional mechanism for the acceleration of deuterons to 100–500 keV.     

Stability of compression of the inner array plasma in nested arrays

The implosion of nested fiber/wire arrays was studied experimentally at the Angara-5-1 facility. The outer array consisted of kapron fibers, while the inner array was made of tungsten wires. The experiments were carried out at a discharge current of 3 MA. Stable compression of the inner array plasma was achieved by increasing the number of fibers in the outer array. In this case, a compact Z-pinch formed at the array axis. Near the pinch, no trailing plasma produced from the high-Z material of the inner array and capable of scattering and reradiating X-ray photons was observed. The trailing edge of the X-ray pulse was found to shorten in the absence of the trailing plasma around the pinch.     

Experimental and numerical studies of plasma production in the initial stage of implosion of a cylindrical wire array

The features are studied of plasma production in the initial stage of implosion of hollow cylindrical wire arrays at electric-field growth rates of 10¹² V/(cm s). The results are presented from the analysis of both UV emission from the wire plasma and the discharge parameters in the initial stage of the formation of a Z-pinch discharge. It is found that, a few nanoseconds after applying voltage to a tungsten wire array, a plasma shell arises on the wire surface and the array becomes a heterogeneous system consisting of metal wire cores and a plasma surrounding each wire (a plasma corona). As a result, the current switches from the wires to the plasma. A further heating and ionization of the wire material are due primarily to heat transfer from the plasma corona. A model describing the primary breakdown along the wires is created with allowance for the presence of low-Z impurities on the wire surface.     

Generation of soft X-ray emission by Z-pinches powered from helical explosive magnetocumulative generators

Results are presented from experiments on the implosion of wire arrays powered from 100-and 200-mm-diameter helical explosive magnetocumulative generators with explosive opening switches. The experiments were performed at load currents of up to 4 MA, the current rise time being 0.3–0.4 μs. The maximum soft X-ray yield of ～ 100 kJ was achieved at a pinch plasma temperature of 55 eV. A two-dimensional MHD code was developed to simulate the process of liner implosion and the generation of X-ray emission. The results of computer simulations agree satisfactorily with the experimental data.     

Study of the expansion dynamics of the plasma of a thin aluminum foil under the action of soft X-ray emission

Results are presented from experiments on the irradiation of thin aluminum foils by an intense soft X-ray (SXR) source on the basis of the Z-pinch formed during the implosion of a tungsten wire array at the Angara-5-1 facility. The state of the foil target is examined by taking two-dimensional X-ray frames. The expansion velocity of the plasma formed under the action of pulsed SXR emission on the front (irradiated) and back sides of the foil and the glow intensity of aluminum plasma on the back side are found from the spatial distribution of the radiation intensity of the plasma of the irradiated foil. The time at which the foil plasma becomes transparent to Z-pinch radiation is determined from the increase in the intensity of transmitted SXR emission.     

Compression dynamics of quasi-spherical wire arrays with different linear mass profiles

Results of experimental studies of the implosion of quasi-spherical wire (or metalized fiber) arrays are presented. The goal of the experiments was to achieve synchronous three-dimensional compression of the plasma produced in different regions of a quasi-spherical array into its geometrical center. To search for optimal synchronization conditions, quasi-spherical arrays with different initial profiles of the linear mass were used. The following dependences of the linear mass on the poloidal angle were used: m _l (θ) ∝ sin^–1θ and m _l (θ) ∝ sin^–2θ. The compression dynamics of such arrays was compared with that of quasi-spherical arrays without linear mass profiling, m _l (θ) = const. To verify the experimental data, the spatiotemporal dynamics of plasma compression in quasi-spherical arrays was studied using various diagnostics. The experiments on three-dimensional implosion of quasi-spherical arrays made it possible to study how the frozen-in magnetic field of the discharge current penetrates into the array. By measuring the magnetic field in the plasma of a quasi-spherical array, information is obtained on the processes of plasma production and formation of plasma flows from the wire/fiber regions with and without an additionally deposited mass. It is found that penetration of the magnetic flux depends on the initial linear mass profile m _l (θ) of the quasi-spherical array. From space-resolved spectral measurements and frame imaging of plasma X-ray emission, information is obtained on the dimensions and shape of the X-ray source formed during the implosion of a quasi-spherical array. The intensity of this source is estimated and compared with that of the Z-pinch formed during the implosion of a cylindrical array.     

Multichannel vacuum arc discharge used for Z-pinch formation

Results are presented from experimental studies of the implosion dynamics and radiative characteristics of an aluminum Z-pinch formed from a plasma shell (PS). The PS with an initial diameter of 4 cm was produced with the help of a multichannel vacuum arc discharge and formed due to the evaporation of the electrode material in ten parallel arc discharges. The PS composition depended on the electrode material in the arc discharge. The described experiments were performed with aluminum electrodes. The total arc current was 80 kA. The PS implosion was provided by an IMRI-5 high-current generator with a current amplitude of 450 kA and rise time of 500 ns. The PS implosion resulted in the formation of a 0.2-cm-diameter plasma column with an electron temperature of 700?C900 eV and average ion density of (5?C8) × 10¹⁷ cm^?3. The maximum radiation power per unit length in aluminum K-lines reached 300 MW/cm, the duration of the radiation pulse being 20 ns.     

Dynamics of the implosion of a tungsten wire array onto the central aluminum wire

Results are presented from the studies of the magnetic implosion of a tungsten wire liner onto an aluminum wire at currents of 2.0–2.6 MA. The experiments were carried out in the S-300 high-power pulsed facility at the Russian Research Centre Kurchatov Institute. The liner is composed of 50 wires 6 μm in diameter and 1 cm in length, which are equally spaced on a circle 1 cm in diameter. An aluminum wire 120 μm in diameter is positioned at the array axis. The liner implosion was accompanied by the generation of VUV and soft X-ray emission. The parameters of the pinch plasma produced during the liner implosion onto the aluminum wire were determined from the time-resolved spectral measurements by a five-channel polychromator. The ion and electron densities turned out to be equal to n _i≈4×10¹⁹ cm⁻³ and n _e≈4×10²⁰ cm⁻³, respectively, and the electron temperature was T _e≈40 eV. The radiation energy measured in the range 50–600 eV was 2–10 kJ. The sources of soft X-ray emission in hydrogen-and helium-like aluminum lines were the bright spots and local objects (clouds) formed in the plasma corona at an electron temperature of 200–500 eV and electron density of 10²¹–10²² cm⁻³. The possibility of both the generation of an axial magnetic field during the liner implosion and the conversion of the energy of this field into soft X-ray emission is discussed. __________ Translated from Fizika Plazmy, Vol. 28, No. 6, 2002, pp. 514–521. Original Russian Text Copyright ? 2002 by Bakshaev, Blinov, Dan'ko, Ivanov, Klír, Korolev, Kravárik, Krása, Kubeš, Tumanov, Chernenko, Chesnokov, Shashkov, Juha.     

Study of the implosion characteristics of quasi-spherical wire arrays on the Angara-5-1 facility at currents of up to 4 MA

Results are presented from experimental studies of the spatial distribution of the density of matter in the central part of the discharge gap and the formation of the temporal profile of the X-ray power in the course of implosion of quasi-spherical wire arrays at discharge currents of up to 4 MA. The spatial distribution of the X-ray intensity in the central part of the discharge gap and the temporal profile of the X-ray power are used as implosion characteristics of quasi-spherical wire arrays. The quasi-spherical arrays were formed by the radial stretching of unstrained wires of initially cylindrical and conical wire arrays under the action of the electrostatic field. The temporal profile of the output X-ray pulse in the photon energy range of 0.1–1 keV is shown to depend on both the geometrical parameters of the quasi-spherical array and the longitudinal distribution of its mass. It is found that a 40% increase in the wire mass due to deposition of an additional mass in the equatorial region of a quasi-spherical array leads to a 15% increase in the average current radius of the pinch and a 30% decrease in the X-ray yield. Experiments with quasi-spherical arrays made of kapron fibers with deposited Al and Bi conducting layers were also carried out. It is demonstrated that application of such arrays makes it possible to control the profile and duration of the generated X-ray pulse by varying the mass, material, and location of the deposited layer. It is found that deposition of an additional mass in the form of a thin Bi stripe on tungsten wires near the cathode end of the array allows one to mitigate the influence of the cathode zipper effect on the pinch compression and formation of the X-ray pulse in tungsten arrays.     

Collective ion acceleration during the decay of a high-current Z-pinch

A study is made of the Z-pinch plasma expansion after the current is switched off. Measurements were carried out in experiments on the implosion of tungsten wire arrays in the Angara-5-1 facility. It is found experimentally that, at a distance of 2 m from the pinch, the ion velocity in the expanding Z-pinch plasma is about (2.5–4.0) × 10⁷ cm/s, which substantially exceeds the thermal velocity of tungsten ions. A model describing the plasma expansion process is proposed that is based on the ambipolar acceleration mechanism. The results of numerical simulations are compared with the experimental data.     

Study of the magnetic fields and soft X-ray emission generated in the implosion of double wire arrays

Results are presented from measurements of the azimuthal magnetic field generated during the implosion of double (nested) tungsten wire arrays in the Angara-5-1 facility at currents of ～3 MA. It is found that the inner array affects the current distribution in the interarray space and that there is an optimal mass (an optimal number of wires) of the inner array at which the full width at half-maximum of the soft X-ray pulse (in the photon energy range of >100 eV) is minimal. On the average, double wire arrays provide a better reproductibility, higher power, and shorter duration of the soft X-ray pulse in comparison to single arrays.     

Dynamics of an Al wire corona of a megaampere Z-pinch

It is shown that the development of instabilities in a Z-pinch plasma formed by loading a relatively thick Al wire (an initial diameter of 120 μm and a maximum discharge current of 2–3 MA) is slowed down due to the high plasma density in the wire corona. A cylindrically symmetric, regular, and stable corona surrounding the wire contains a helical formation with a dense, cold, and magnetized plasma. X-ray pulses with a photon energy of several keV and an FWHM duration of 10–20 ns are generated by a few imploded neck structures in the pinch phase of the corona evolution (70–100 ns after the current onset). The main part of X radiation emitted by individual bright spots in the photon energy range 1.5–2.4 keV (up to 40 J at a peak power of 4 GW) consists of the continuum and the bound-bound transition radiation from H-and He-like Al ions. A possible scenario for the axial magnetic field evolution during an X-ray pulse is outlined. __________ Translated from Fizika Plazmy, Vol. 28, No. 4, 2002, pp. 329–336. Original Russian Text Copyright ? 2002 by Kubeš, Renner, Krousky, Kravárik, Bakshaev, Blinov, Chernenko, Gordeev, Dan’ko, Korolev, Shashkov.