Biomass feedstock preprocessing and long‐distance transportation logistics

Biomass‐based biofuels have gained attention because they are renewable energy sources that could facilitate energy independence and improve rural economic development. As biomass supply and biofuel demand areas are generally not geographically contiguous, the design of an efficient and effective biomass supply chain from biomass provision to biofuel distribution is critical to facilitate large‐scale biofuel development. This study compared the costs of supplying biomass using three alternative biomass preprocessing and densification technologies (pelletizing, briquetting, and grinding) and two alternative transportation modes (trucking and rail) for the design of a four‐stage biomass–biofuel supply chain in which biomass produced in Illinois is used to meet biofuel demands in either California or Illinois. The BioScope optimization model was applied to evaluate a four‐stage biomass–biofuel supply chain that includes biomass supply, centralized storage and preprocessing (CSP), biorefinery, and ethanol distribution. We examined the cost of 15 scenarios that included a combination of three biomass preprocessing technologies and five supply chain configurations. The findings suggested that the transportation costs for biomass would generally follow the pattern of coal transportation. Converting biomass to ethanol locally and shipping ethanol over long distances is most economical, similar to the existing grain‐based biofuel system. For the Illinois–California supply chain, moving ethanol is Biomass‐based biofuels have gained attention because they are renewable energy sources that could facilitate energy independence and improve rural economic development. As biomass supply and biofuel demand areas are generally not geographically contiguous, the design of an efficient and effective biomass supply chain from biomass provision to biofuel distribution is critical to facilitate large‐scale biofuel development. This study compared the costs of supplying biomass using three alternative biomass preprocessing and densification technologies (pelletizing, briquetting, and grinding) and two alternative transportation modes (trucking and rail) for the design of a four‐stage biomass–biofuel supply chain in which biomass produced in Illinois is used to meet biofuel demands in either California or Illinois. The BioScope optimization model was applied to evaluate a four‐stage biomass–biofuel supply chain that includes biomass supply, centralized storage and preprocessing (CSP), biorefinery, and ethanol distribution. We examined the cost of 15 scenarios that included a combination of three biomass preprocessing technologies and five supply chain configurations. The findings suggested that the transportation costs for biomass would generally follow the pattern of coal transportation. Converting biomass to ethanol locally and shipping ethanol over long distances is most economical, similar to the existing grain‐based biofuel system. For the Illinois–California supply chain, moving ethanol is $0.24 gal^?1 less costly than moving biomass even in densified form over long distances. The use of biomass pellets leads to lower overall costs of biofuel production for long‐distance transportation but to higher costs if used for short‐distance movement due to its high capital and processing costs. Supported by the supply chain optimization modeling, the cellulosic‐ethanol production and distribution costs of using Illinois feedstock to meet California demand are $0.08 gal^?1 higher than that for meeting local Illinois demand.     

Variation in Cell Wall Composition and Accessibility in Relation to Biofuel Potential of Short Rotation Coppice Willows

Short rotation coppice (SRC) willow is currently emerging as an important dedicated lignocellulosic energy crop in the UK. However, investigation into the variation between species and genotypes in their suitability for liquid transport biofuel processing has been limited. To address this, four traits relevant to biofuel processing (composition, enzymatic saccharification, response to pretreatment and projected ethanol yields) were studied in 35 genotypes of willow including Europe’s leading SRC willow cultivars. Large, genotype-specific variation was observed for all four traits. Significant positive correlations were identified between the accessibility of glucan to enzymatic saccharification before and after pretreatment as well as glucose release and xylose release via acid hydrolysis during pretreatment. Of particular interest is that the lignin content of the biomass did not correlate with accessibility of glucan to enzymatic saccharification. The genotype-specific variations identified have implications for SRC willow breeding and for potential reductions in both the net energy expenditure and environmental impact of the lignocellulosic biofuel process chain. The large range of projected ethanol yields demonstrate the importance of feedstock selection based on an ideotype encompassing the performance of both field biomass growth and ease of conversion.     

Optimal Locations for Methanol and CHP Production in Eastern Finland

Finland considers energy production from woody biomass as an efficient energy planning strategy to increase the domestic renewable energy production in order to substitute fossil fuel consumption and reduce greenhouse gas emissions. Consequently, a number of developmental activities are implemented in the country, and one of them is the installation of second generation liquid biofuel demonstration plants. In this study, two gasification-based biomass conversion technologies, methanol and combined heat and power (CHP) production, are assessed for commercialization. Spatial information on forest resources, sawmill residues, existing biomass-based industries, energy demand regions, possible plant locations, and a transport network of Eastern Finland is fed into a geographically explicit Mixed Integer Programming model to minimize the costs of the entire supply chain which includes the biomass supply, biomass and biofuel transportation, biomass conversion, energy distribution, and emissions. The model generates a solution by determining the optimal number, locations, and technology mix of bioenergy production plants. Scenarios were created with a focus on biomass and energy demand, plant characteristics, and cost variations. The model results state that the biomass supply and high energy demand are found to have a profound influence on the potential bioenergy production plant locations. The results show that methanol can be produced in Eastern Finland under current market conditions at an average cost of 0.22??/l with heat sales (0.34??/l without heat sales). The introduction of energy policy tools, like cost for carbon, showed a significant influence on the choice of technology and CO₂ emission reductions. The results revealed that the methanol technology was preferred over the CHP technology at higher carbon dioxide cost (>145??/t_CO2). The results indicate that two methanol plants (360?MW_biomass) are needed to be built to meet the transport fuel demand of Eastern Finland.     

Managing Feedstock Supply Risk for the Development of a US Stover Biofuel Industry

Feedstock supply risk is one of the key concerns limiting cellulosic biofuel expansion. We use an economic model of corn stover-based ethanol production to investigate strategies to manage stover supply uncertainty, including three contract arrangements that vary according to risk-sharing between the processor and farmers. Applying this model to corn stover-based ethanol in the USA, we find that a greater quantity of biofuel is supplied at lower cost under right-of-access contracts than a delivered quantity contract. The processor can manage some of the risk borne under the right-of-access contracts by contracting excess acreage and, if available, by purchasing deficit stover from a spot market. Contracting excess acreage increases the expected biofuel cost but results in lower uncertainty surrounding cellulosic biofuel supply. A biomass spot market provides a source of biomass during low yielding years, but can also create competition for the processor as an alternative outlet for farmers to supply stover under favorable spot market prices. In general, farmers’ contract preferences are responsive to the basic structure of incentives, which could provide flexibility to processors as the industry develops and market uncertainties change.     

Recent trends in ionic liquid (IL) tolerant enzymes and microorganisms for biomass conversion

Second generation biofuel production depends on lignocellulosic (LC) biomass transformation into simple sugars and their subsequent fermentation into alcohols. However, the main obstacle in this process is the efficient breakdown of the recalcitrant cellulose to sugar monomers. Hence, efficient feedstock pretreatment and hydrolysis are necessary to produce a cost effective biofuel. Recently, ionic liquids (ILs) have been recognized as a promising solvent able to dissolve different biomass feedstocks, providing higher sugar yields. However, most of the hydrolytic enzymes and microorganisms are inactivated, completely or partially, in the presence of even low concentrations of IL, making necessary the discovery of novel hydrolytic enzymes and fermentative microorganisms that are tolerant to ILs. In this review, the current state and the challenges of using ILs as a pretreatment of LC biomass was evaluated, underlining the advances in the discovery and identification of new IL-tolerant enzymes and microorganisms that could improve the bioprocessing of biomass to fuels and chemicals.     

Modifying plants for biofuel and biomaterial production

The productivity of plants as biofuel or biomaterial crops is established by both the yield of plant biomass per unit area of land and the efficiency of conversion of the biomass to biofuel. Higher yielding biofuel crops with increased conversion efficiencies allow production on a smaller land footprint minimizing competition with agriculture for food production and biodiversity conservation. Plants have traditionally been domesticated for food, fibre and feed applications. However, utilization for biofuels may require the breeding of novel phenotypes, or new species entirely. Genomics approaches support genetic selection strategies to deliver significant genetic improvement of plants as sources of biomass for biofuel manufacture. Genetic modification of plants provides a further range of options for improving the composition of biomass and for plant modifications to assist the fabrication of biofuels. The relative carbohydrate and lignin content influences the deconstruction of plant cell walls to biofuels. Key options for facilitating the deconstruction leading to higher monomeric sugar release from plants include increasing cellulose content, reducing cellulose crystallinity, and/or altering the amount or composition of noncellulosic polysaccharides or lignin. Modification of chemical linkages within and between these biomass components may improve the ease of deconstruction. Expression of enzymes in the plant may provide a cost‐effective option for biochemical conversion to biofuel.     

Application of metagenomic techniques in mining enzymes from microbial communities for biofuel synthesis

Feedstock for biofuel synthesis is transitioning to lignocelluosic biomass to address criticism over competition between first generation biofuels and food production. As microbial catalysis is increasingly applied for the conversion of biomass to biofuels, increased import has been placed on the development of novel enzymes. With revolutionary advances in sequencer technology and metagenomic sequencing, mining enzymes from microbial communities for biofuel synthesis is becoming more and more practical. The present article highlights the latest research progress on the special characteristics of metagenomic sequencing, which has been a powerful tool for new enzyme discovery and gene functional analysis in the biomass energy field. Critical enzymes recently developed for the pretreatment and conversion of lignocellulosic materials are evaluated with respect to their activity and stability, with additional explorations into xylanase, laccase, amylase, chitinase, and lipolytic biocatalysts for other biomass feedstocks.     

Chloroplast molecular farming: efficient production of a thermostable xylanase by Nicotiana tabacum plants and long-term conservation of the recombinant enzyme

The high cost of recombinant enzymes for the production of biofuel from ligno-cellulosic biomass is a crucial factor affecting the economic sustainability of the process. The use of plants as biofactories for the production of the suitable recombinant enzymes might be an alternative to microbial fermentation. In the case of enzyme accumulation in chloroplasts, it is fundamental to focus on the issue of full photosynthetic efficiency of transplastomic plants in the field where they might be exposed to abiotic stress such as high light intensity and high temperature. Xylanases (EC 3.2.1.8), a group of enzymes that hydrolyse linear polysaccharides of beta-1,4-xylan into xylose, find an application in the biofuel industry favouring biomass saccharification along with other cell-wall degrading enzymes. In the present study, we analysed how a high level of accumulation of a thermostable xylanase in tobacco chloroplasts does not impact on photosynthetic performance of transplastomic plants grown outdoors. The recombinant enzyme was found to be stable during plant development, ex planta and after long-term storage.     

Economic Analysis of the Potential of Cellulosic Biomass Available in France from Agricultural Residue and Energy Crops

The objective of this research is to evaluate the feasibility and locations of using cellulosic biomass both from crop residues and from dedicated energy crops to supply 200-million-liter-biodiesel plants in France. The estimation of the potential amount of agricultural residue available in 2015 in each region of France is calculated. The residues considered in this study come from cereal straw and corn stover. Results show that eight out of the twenty one French regions have enough agricultural residues available to supply at least one 200 million liter biofuel plant. Region Centre has the largest potential, with enough residues to supply three to five plants. Finally, cost of supplying one biodiesel plant of 200 million liters in the region Centre is estimated. Results show that collection of biomass will be effective in an area with a radius of 58 Km to 168 Km depending of the raw material considered and its abundance. The cost of supplying a plant with miscanthus is much higher than with residues only. Thus, crop residues appear to offer a lower cost to produce biodiesel in the near term compared to a dedicated crop. Results show that production of biofuel from cellulosic biomass should not be limited by the supply of raw material, but costs of conversion to liquid fuels clearly will play a key role in the development of cellulosic biofuels. Energy prices and policies will have a significant impact on second generation biofuel development.     

Economic impact of combined torrefaction and pelletization processes on forestry biomass supply

The cost of supplying wood biomass from forestry operations in remote areas has been an obstacle to expansion of forest‐based bioenergy in much of the western United States. Economies of scale in the production of liquid fuels from lignocellulosic biomass feedstocks favor large centralized biorefineries. Increasing transportation efficiency through torrefaction and pelletization at distributed satellite facilities may serve as a means to expand the utilization of forestry residuals in biofuel production. To investigate this potential, a mixed‐integer linear program was developed to optimize the feedstock supply chain design with and without distributed pretreatment. The model uses techno‐economic assessment of scale‐dependent biomass pretreatment processes from existing literature and multimodal biomass transportation cost evaluations derived from a spatially explicit network analysis as input. In addition, the sensitivity of the optimal system configuration was determined for variations of key input parameters including the production scale of pretreatment facilities, road and rail transportation costs, and feedstock procurement costs. Torrefaction and densification were found to reduce transportation costs by $0.84 per GJ and overall delivered costs by $0.24 per GJ, representing 14.5% and 5.2% cost reductions compared to feedstock collection without pretreatment. Significant uncertainties remain in terms of the costs associated with deploying torrefaction equipment at the scales modeled, but the level of potential cost savings suggests further analysis and development of these alternatives.     

Bioenergy from permanent grassland – A review: 2. Combustion

The aim of this review is to summarize current knowledge on suitability and sustainability of grassland biomass for combustion. In the first section grassland management for solid biofuel as well as information on harvest, postharvest and firing technology are described. An extensive grassland management system with one late cut and low level of fertilization is favored for grass as a solid biofuel. The grass harvest usually involves drying in the field and clearing with conventional farm machinery. Pelleting or briquetting improves the biofuel quality. Grass combustion is possible as stand-alone biomass-firing or co-firing with other fuels. Firing herbaceous biomass requires various specific adaptations of the different combustion technologies. In the second section economic and environmental aspects are discussed. Costs for biomass supply mainly depend on yields and harvesting technologies, while combustion costs are influenced by the size and technical design of the plant. Market prices for grass and possible subsidies for land use are crucial for profitability. Regarding biogeochemical cycles a specific feature of combustion is the fact that none of the biomass carbon and nitrogen removed at harvest is available for return to the grassland. These exports can be compensated for by fixation from the air given legumes in the vegetation and sufficient biomass production. Greenhouse gas emissions can be considerably reduced by grass combustion. Solid biofuel production has a potential for predominantly positive impacts on biodiversity due to the extensive grassland management.     

Microalgal production — A close look at the economics

Worldwide, microalgal biofuel production is being investigated. It is strongly debated which type of production technology is the most adequate. Microalgal biomass production costs were calculated for 3 different micro algal production systems operating at commercial scale today: open ponds, horizontal tubular photobioreactors and flat panel photobioreactors. For the 3 systems, resulting biomass production costs including dewatering, were 4.95, 4.15 and 5.96 € per kg, respectively. The important cost factors are irradiation conditions, mixing, photosynthetic efficiency of systems, medium- and carbon dioxide costs. Optimizing production with respect to these factors, a price of € 0.68 per kg resulted. At this cost level microalgae become a promising feedstock for biodiesel and bulk chemicals.

Summary

Photobioreactors may become attractive for microalgal biofuel production.     

Logistics system design for biomass-to-bioenergy industry with multiple types of feedstocks

It is technologically possible for a biorefinery to use a variety of biomass as feedstock including native perennial grasses (e.g., switchgrass) and agricultural residues (e.g., corn stalk and wheat straw). Incorporating the distinct characteristics of various types of biomass feedstocks and taking into account their interaction in supplying the bioenergy production, this paper proposed a multi-commodity network flow model to design the logistics system for a multiple-feedstock biomass-to-bioenergy industry. The model was formulated as a mixed integer linear programming, determining the locations of warehouses, the size of harvesting team, the types and amounts of biomass harvested/purchased, stored, and processed in each month, the transportation of biomass in the system, and so on. This paper demonstrated the advantages of using multiple types of biomass feedstocks by comparing with the case of using a single feedstock (switchgrass) and analyzed the relationship of the supply capacity of biomass feedstocks to the output and cost of biofuel.     

生物质燃料

石化资源的溃乏以及其飚升的价格使得今天生物能源的研究越来越受到关注。从传统的生物供能方式——燃烧开始,介绍发酵制气、生物电池等最新的生物供能方式,以求对生物燃料作一较为详细的介绍,并对其应用前景进行展望。     

Development and status of dedicated energy crops in the United States

The biofuel industry is rapidly growing because of increasing energy demand and diminishing petroleum reserves on a global scale. A multitude of biomass resources have been investigated, with high-yielding, perennial feedstocks showing the greatest potential for utilization as advanced biofuels. Government policy and economic drivers have promoted the development and commercialization of biofuel feedstocks, conversion technologies, and supply chain logistics. Research and regulations have focused on the environmental consequences of biofuels, greatly promoting systems that reduce greenhouse gas emissions and life-cycle impacts. Numerous biofuel refineries using lignocellulosic feedstocks and biomass-based triglycerides are either in production or pre-commercial development phases. Leading candidate energy crops have been identified, yet require additional efforts to realize their full potential. Advanced biofuels, complementing conventional biofuels and other renewable energy sources such as wind and solar, provide the means to substantially displace humanity’s reliance on petroleum-based energy.     

Biomass Yield and Quality of Reed Canarygrass under Five Harvest Management Systems for Bioenergy Production

Reed canarygrass, Phalaris arundinacea L., produces high biomass yields in cool climates and wetlands. The number and timing of harvests during a growing season directly affect biomass yield and biofuel quality. In order to determine optimum harvest management, seven cultivars of reed canarygrass were planted in field experiments at Ames, IA; McNay, IA; and Arlington, WI in the upper Midwestern USA and harvested once in autumn or in winter, twice in spring + autumn or spring + winter, or three times during the season as hay. Biomass yield varied considerably among harvest treatments, locations, and years, ranging up to 12.6 Mg ha^?1. Dry matter percentage ranged from 37% for spring-harvested biomass to 84% for overwintered biomass. The three harvest hay and two harvest spring + autumn managements produced the highest biomass yield compared to other systems, but the advantage, if any, of hay management was small and probably does not justify the cost of additional fieldwork. More mature biomass, such as that found in the single harvest systems, had higher fiber concentrations. Overwintered biomass had superior biofuel quality, being low in P, K, S, and Cl and high in cell wall concentration. However, winter harvest systems had lower yield than autumn harvest and in some years, no harvest was possible due to lodging from snow compaction. The main limitation of a two harvest system is the high moisture content of the late spring/early summer biomass.     

木质纤维素预处理及高值化技术研究进展

木质纤维素生物质是地球上最丰富的可再生生物资源.随着化石能源的消耗及环境的污染,以取代石化燃料为目标的由生物质向生物燃料的转化受到了广泛的关注.木质纤维素有很强的天然抗降解屏障,需先通过物理、化学及微生物等手段进行预处理,进而以更低的成本和更高的效率转化为生物燃料及其他高附加值产品.本文在总结酸碱等传统预处理方法优缺点...     

Co-Cultivation of Fungal and Microalgal Cells as an Efficient System for Harvesting Microalgal Cells,Lipid Production and Wastewater Treatment

The challenges which the large scale microalgal industry is facing are associated with the high cost of key operations such as harvesting, nutrient supply and oil extraction. The high-energy input for harvesting makes current commercial microalgal biodiesel production economically unfeasible and can account for up to 50% of the total cost of biofuel production. Co-cultivation of fungal and microalgal cells is getting increasing attention because of high efficiency of bio-flocculation of microalgal cells with no requirement for added chemicals and low energy inputs. Moreover, some fungal and microalgal strains are well known for their exceptional ability to purify wastewater, generating biomass that represents a renewable and sustainable feedstock for biofuel production. We have screened the flocculation efficiency of the filamentous fungus A. fumigatus against 11 microalgae representing freshwater, marine, small (5 µm), large (over 300 µm), heterotrophic, photoautotrophic, motile and non-motile strains. Some of the strains are commercially used for biofuel production. Lipid production and composition were analysed in fungal-algal pellets grown on media containing alternative carbon, nitrogen and phosphorus sources contained in wheat straw and swine wastewater, respectively. Co-cultivation of algae and A. fumigatus cells showed additive and synergistic effects on biomass production, lipid yield and wastewater bioremediation efficiency. Analysis of fungal-algal pellet''s fatty acids composition suggested that it can be tailored and optimised through co-cultivating different algae and fungi without the need for genetic modification.     

Closed photobioreactors for production of microalgal biomasses

Microalgal biomasses have been produced industrially for a long history for application in a variety of different fields. Most recently, microalgae are established as the most promising species for biofuel production and CO(2) bio-sequestration owing to their high photosynthesis efficiency. Nevertheless, design of photobioreactors that maximize solar energy capture and conversion has been one of the major challenges in commercial microalga biomass production. In this review, we systematically survey the recent developments in this field.     

Biomass to fuels via microbial transformations

The conversion of biomass to fuels is advancing on two fronts: first, to enhance the usability of biomass and second, to generate the best fuel molecule(s). Lignin generally presents a barrier to biomass utilization; this problem may be circumvented by the genetic alteration of lignin-producing plants. Plant cellulosic material will need to be utilized more efficiently, requiring a greater knowledge of the multiprotein complex, the cellulosome. Many biofuel types are being considered: alcohols, esters, ethers, and hydrocarbons. Intrinsic alcohol toxicity to cells may impose limitations on ethanol and n-butanol production. Biodiesel, or fatty acid esters, can now be synthesized via recombinant Escherichia coli and may offer an improvement over alcohol fermentations. Biopetroleum (hydrocarbons) is being considered as an alternative biofuel.