Lubrication and load-bearing properties of human salivary pellicles adsorbed ex vivo on molecularly smooth substrata

In a series of Surface Force Balance experiments, material from human whole saliva was adsorbed to molecularly smooth mica substrata (to form an ‘adsorbed salivary film’). Measurements were taken of normal (load bearing, F _n) and shear (frictional, F _s*) forces between two interacting surfaces. One investigation involved a salivary film formed by overnight adsorption from undiluted, centrifuged saliva, with the adsorbed film rinsed with pure water before measurement. Measurements were taken under pure water and 70 mM NaNO₃. In a second investigation, a film was formed from and measured under a solution of 7% filtered saliva in 10 mM NaNO₃. F _n results for both systems showed purely repulsive layers, with an uncompressed thickness of 35–70 nm for the diluted saliva investigation and, prior to the application of shear, 11 nm for the rinsed system. F _s* was essentially proportional to F _n for all systems and independent of shear speed (in the range 100–2000 nm s^?1), with coefficients of friction  μ ～ 0.24 and μ ～ 0.46 for the unrinsed and rinsed systems, respectively. All properties of the rinsed system remained similar when the pure water measurement environment was changed to 70 mM NaNO₃. For all systems studied, shear gave rise to an approximately threefold increase in the range of normal forces, attributed to the ploughing up of adsorbed material during shear to form debris that stood proud of the adsorbed layer. The results provide a microscopic demonstration of the wear process for a salivary film under shear and may be of particular interest for understanding the implications for in vivo oral lubrication under conditions such as rinsing of the mouth cavity. The work is interpreted in light of earlier studies that showed a structural collapse and increase in friction for an adsorbed salivary film in an environment of low ionic strength.     

Normal and frictional interactions of purified human statherin adsorbed on molecularly-smooth solid substrata

Human salivary statherin was purified from parotid saliva and adsorbed to bare hydrophilic (HP) mica and STAI-coated hydrophobic (HB) mica in a series of Surface Force Balance experiments that measured the normal (F(n)) and friction forces (F(s)*) between statherin-coated mica substrata. Readings were taken both in the presence of statherin solution (HP and HB mica) and after rinsing (HP mica). F(n) measurements showed, for both substrata, monotonic steric repulsion that set on at a surface separation D ~20 nm, indicating an adsorbed layer whose unperturbed thickness was ca 10 nm. An additional longer-ranged repulsion, probably of electrostatic double-layer origin, was observed for rinsed surfaces under pure water. Under applied pressures of ~1 MPa, each surface layer was compressed to a thickness of ca 2 nm on both types of substratum, comparable with earlier estimates of the size of the statherin molecule. Friction measurements, in contrast with F(n) observations, were markedly different on the two different substrata: friction coefficients, μ ≡ ?F(s)*/?F(n), on the HB substratum (μ ≈ 0.88) were almost an order of magnitude higher than on the HP substratum (μ ≈ 0.09 and 0.12 for unrinsed and rinsed, respectively), and on the HB mica there was a lower dependence of friction on sliding speed than on the HP mica. The observations were attributed to statherin adsorbing to the mica in multimer aggregates, with internal re-arrangement of the protein molecules within the aggregate dependent on the substratum to which the aggregate adsorbed. This internal re-arrangement permitted aggregates to be of similar size on HP and HB mica but to have different internal molecular orientations, thus exposing different moieties to the solution in each case and accounting for the very different friction behaviour.     

Characterisation of structures in salivary secretion film formation. An experimental study with atomic force microscopy

The purpose of the present study was to characterise the structure dynamics of pure salivary secretions retained on controlled surfaces with different surface energies in the early stage of salivary film formation. Germanium prisms prepared to have either low surface energy or medium surface energy were incubated in fresh secretions of either human parotid saliva (HPS) or human submandibular/sublingual saliva (HSMSLS) for 15, 90, and 180 min. After controlled rinsing with distilled water, the surfaces were air dried and thereafter imaged with atomic force microscopy (AFM). The amount of adsorbed material and the size of the structures detected increased with increased saliva exposure time. The film thicknesses varied from 10 to 150 nm, and both HPS and HSMSLS films contained structures with diameters varying from 40 nm to 2 microm. Some of these were clustered into special formations. The HPS films exhibited a more granular morphology than the HSMSLS films. Furthermore, branched lines were detected on the low surface energy germanium prisms incubated in saliva. The results indicate that exposure time, surface energy, and type of salivary secretion all are factors affecting the adsorption characteristics of salivary films.     

Characterisation of Structures in Salivary Secretion Film Formation. An Experimental Study with Atomic Force Microscopy

The purpose of the present study was to characterise the structure dynamics of pure salivary secretions retained on controlled surfaces with different surface energies in the early stage of salivary film formation. Germanium prisms prepared to have either low surface energy or medium surface energy were incubated in fresh secretions of either human parotid saliva (HPS) or human submandibular/sublingual saliva (HSMSLS) for 15, 90, and 180 min. After controlled rinsing with distilled water, the surfaces were air dried and thereafter imaged with atomic force microscopy (AFM). The amount of adsorbed material and the size of the structures detected increased with increased saliva exposure time. The film thicknesses varied from 10 to 150 nm, and both HPS and HSMSLS films contained structures with diameters varying from 40 nm to 2 μm. Some of these were clustered into special formations. The HPS films exhibited a more granular morphology than the HSMSLS films. Furthermore, branched lines were detected on the low surface energy germanium prisms incubated in saliva. The results indicate that exposure time, surface energy, and type of salivary secretion all are factors affecting the adsorption characteristics of salivary films.     

Adsorption from saliva to silica and hydroxyapatite surfaces and elution of salivary films by SDS and delmopinol

The adsorption of proteins from human whole saliva (HWS) onto silica and hydroxyapatite surfaces (HA) was followed by quartz crystal microbalance with dissipation (QCM-D) and ellipsometry. The influence of different surface properties and adsorption media (water and PBS) on the adsorption from saliva was studied. The viscoelastic properties of the salivary films formed on the solid surfaces were estimated by the use of the Voigt-based viscoelastic film model. Furthermore, the efficiency of SDS and delmopinol to elute the adsorbed salivary film from the surfaces was investigated at different surfactant concentrations. A biphasic kinetic regime for the adsorption from saliva on the silica and HA surfaces was observed, indicating the formation of a rigidly coupled first layer corresponding to an initial adsorption of small proteins and a more loosely bound second layer. The results further showed a higher adsorption from HWS onto the HA surfaces compared to the silica surfaces in both adsorption media (PBS and water). The adsorption in PBS led to higher adsorbed amounts on both surfaces as compared to water. SDS was found to be more efficient in removing the salivary film from both surfaces than delmopinol. The salivary film was found to be less tightly bound onto the silica surfaces since more of the salivary film could be removed with both SDS and delmopinol compared to that from the HA surface. When adsorption took place from PBS the salivary layer formed at both surfaces seemed to have a similar structure, with a high energy dissipation implying that a softer salivary layer is built up in PBS as opposed to that in water. Furthermore, the salivary layers adsorbed from water solutions onto the HA were found to be softer than those on silica.     

Normal and frictional interactions of purified human statherin adsorbed on molecularly-smooth solid substrata

Human salivary statherin was purified from parotid saliva and adsorbed to bare hydrophilic (HP) mica and STAI-coated hydrophobic (HB) mica in a series of Surface Force Balance experiments that measured the normal (F _n) and friction forces (F _s*) between statherin-coated mica substrata. Readings were taken both in the presence of statherin solution (HP and HB mica) and after rinsing (HP mica). F _n measurements showed, for both substrata, monotonic steric repulsion that set on at a surface separation D ～ 20 nm, indicating an adsorbed layer whose unperturbed thickness was ca 10 nm. An additional longer-ranged repulsion, probably of electrostatic double-layer origin, was observed for rinsed surfaces under pure water. Under applied pressures of ～ 1 MPa, each surface layer was compressed to a thickness of ca 2 nm on both types of substratum, comparable with earlier estimates of the size of the statherin molecule. Friction measurements, in contrast with F _n observations, were markedly different on the two different substrata: friction coefficients, μ ≡ ?F _s*/?F _n, on the HB substratum (μ ≈ 0.88) were almost an order of magnitude higher than on the HP substratum (μ ≈ 0.09 and 0.12 for unrinsed and rinsed, respectively), and on the HB mica there was a lower dependence of friction on sliding speed than on the HP mica. The observations were attributed to statherin adsorbing to the mica in multimer aggregates, with internal re-arrangement of the protein molecules within the aggregate dependent on the substratum to which the aggregate adsorbed. This internal re-arrangement permitted aggregates to be of similar size on HP and HB mica but to have different internal molecular orientations, thus exposing different moieties to the solution in each case and accounting for the very different friction behaviour.     

Permeability of Oral Tissues to Blood-borne Coxsackievirus B-1

The ability of coxsackievirus B-1 to pass the barriers of the circulatory system into whole saliva has been shown previously. In this investigation, the major salivary glands and the oral mucosa were studied, and their role as participants in the excretion of coxsackievirus B-1 during viremia was evaluated. The effect of the salivary-gland stimulant pilocarpine nitrate on both the salivary flow rate and the recovery of virus during viremia was determined. A comparison was made between the amount of virus recovered from whole saliva during viremia in animals deficient in one or both of the major salivary-gland pairs and animals with a complete complement of salivary glands. The salivary glands in other animals were cannulated, and pure glandular secretions were collected during viremia and assayed for the presence of virus The amount of virus passing from the capillaries of the oral mucosa to the surface was also determined to evaluate this route as a possible site for the excretion of virus into saliva during viremia. The major salivary glands did not excrete appreciable quantities of virus during viremia. The submaxillary-gland secretions did not contain virus, and the parotid-gland secretions showed virus only at extremely high blood virus levels. Either removal of the major salivary glands or decreased salivary flow rates increased the concentration of virus in whole saliva. This observation suggested that the production of saliva by the major salivary glands tends to dilute the virus in the oral cavity. A 0.88-cm² sample of the oral mucosa excreted significantly large amounts of virus during viremia and suggested that the passage of virus through the oral mucosa was the major route for the excretion of virus into saliva during viremia.     

The measurement of hormones in saliva: possibilities and pitfalls

The easy stress-free, non-invasive nature of saliva collection makes it one of the most accessible body fluids and it is potentially of value in studying normal human physiology as well as pathology. Measurements of salivary hormone levels will usually only be of value if they reflect the plasma level of the hormone and the relationship between the saliva and plasma levels of many hormones have been studied by a number of groups. The measurement of the salivary level is a valuable clinical tool for some hormones (e.g. cortisol, oestriol, progesterone), is of little value for others (e.g. cortisone, dehydroepiandrosterone sulphate, thyroxine, pituitary hormones) and for many others the saliva/plasma relationship is not yet sufficiently understood to assess the value of the salivary measurement. As well as reviewing the state of our knowledge of the salivary concentration of many hormones this review outlines a number of "rules of thumb" concerning the presence of hormones in saliva, their saliva/plasma relationship and the potential usefulness of assays of their salivary concentration.     

Stability of salivary steroids: the influences of storage, food and dental care

We studied influences of dental care, food and storage on the reproducibility of salivary steroid levels. Cortisol (F), 17OH-progesterone (17OHP) and Progesterone (P) were measured using adapted commercial radioimmunoassays. Saliva samples of healthy adults (n = 15; m:8; f:7) were collected directly before and after dental care, and directly before and after breakfast with various foodstuffs. A second experiment investigated stability of steroids under different storage conditions. Four series of identical saliva portions (I: Native saliva; II: Centrifuged saliva; III: Saliva with trifluor acetate (TFA); IV: Saliva with 0.5% NaN(3)) were stored at room temperature and at 4 degrees C for up to three weeks. To demonstrate influences of repeated thawing and re-freezing of saliva on steroid values, saliva samples (n = 15) were divided into identical portions. These portions were frozen and re-thawed up to 5 times before measurement. Neither dental care nor intake of bread or milk effected the reproducibility of F, 170HP, and P. Steroid levels decreased significantly in the course of three weeks under different storage conditions (P < 0.001). This decrease was clinically relevant from the second week onward, with exception of NaN(3) treated samples. After repeated freezing and re-thawing 17OHP and P decreased slightly (about 5%). Only F decreased significantly after the third thawing (P < 0.001). The results show the usefulness of standardized handling of saliva samples for improving reproducibility and reliability of salivary steroid measurements.     

Mechanical characterization of in vitro-formed short-term salivary pellicle

Human saliva consists of approximately 98% water and a variety of electrolytes and proteins. Those proteins can be selectively adsorbed onto the enamel surface. The cuticular material formed on the enamel surface is termed acquired salivary pellicle (ASP), which is critical for the health of oral mucosa and teeth. The ASP is composed of a inner layer and a outer layer. The lubricating properties of ASP are closely associated with the inner layer. The aim of this research is to characterize the structural and mechanical properties of the inner layer of ASP. In this paper, enamel specimens were immersed for 1 min in human saliva. The ASP formed in vitro within 1 min was studied using a nanoindenter. The results show that the thickness of the inner layer of ASP is approximately 18 nm. Moreover, the inner layer is a heterogeneous pellicle with a gradient in density. From the surface of the inner layer to the enamel surface, the density and mechanical properties gradually increase. The research results may be helpful to extend the understanding of mechanical properties of salivary pellicle and to the oral hygiene industry for diagnose oral diseases.     

Identification and characterization of tyrosylprotein sulfotransferase from human saliva

Tyrosylprotein sulfotransferase (TPST), the enzyme responsible for the sulfation of tyrosine residues, has been identified and characterized in submandibular salivary glands previously (William et al. Arch Biochem Biophys 338: 90-96). Tyrosylprotein sulfotransferase catalyses the sulfation of a variety of secretory and membrane proteins and is believed to be present only in the cell. In the present study, this enzyme was identified for the first time in human saliva. Analysis of human saliva and parotid saliva for the presence of tyrosylprotein sulfotransferase revealed tyrosine sulfating activity displayed by both whole saliva and parotid saliva at pH optimum of 6.8. In contrast to tyrosylprotein sulfotransferase isolated from submandibular salivary glands, salivary enzyme does not require the presence of Triton X-100, NaF and 5'AMP for maximal activity. Similar to the submandibular TPST, the enzyme from saliva also required MnCl2 for its activity. Maximum TPST activity was observed at 20 mM MnCl2. The enzyme from saliva was immunoprecipitated and purified by immunoaffinity column using anti-TPST antibody. Affinity purified salivary TPST showed a single band of 50-54 kDa. This study is the first report characterizing a tyrosylprotein sulfotransferase in a secretory fluid.     

Intraoral lubrication of PRP-1, statherin and mucin as studied by AFM

The aim of this paper was to elucidate the mechanisms behind salivary lubrication with special emphasis on the lubricity of three key components of the pellicle, viz human acidic proline-rich protein 1 (PRP-1), human statherin and bovine submaxillary mucin (BSM). The lubricating properties of the proteins have been assessed by means of colloidal probe atomic force microscopy, and are discussed in relation to their adsorption behaviour. To various extents, the proteins investigated all showed a lubricating effect when adsorbed to silica surfaces. For comparable concentrations, PRP-1 was found to have a more pronounced lubricating effect than BSM, which in turn showed a higher lubricity than statherin. The relative lubricity is in accordance with previously reported relative adsorbed amounts of the three proteins, within the investigated concentration interval. It is concluded that PRP-1 has the highest lubricating capacity as a pure fraction among the preparations investigated, and that the lubricating effect of PRP-1 as a pure fraction is notably large as compared to the lubricity of human whole saliva.     

Lubricating Properties of the Initial Salivary Pellicle — an AFM Study

The role of saliva in the oral cavity is manifold; an important function is to serve as lubricant between hard (enamel) and soft (mucosal) tissues. Intraoral lubrication is of crucial importance in order to maintain functions such as deglutition, mastication and the faculty of speech. A large number of people suffer from impaired salivary functions, displaying symptoms such as ‘dry mouth’. This results in a need for methods to assess the lubricating properties of both native saliva and potential artificial saliva formulations. Here, normal as well as lateral forces, acting between adsorbed salivary films, have been measured for the first time by means of colloidal probe atomic force microscopy (AFM). It was found that the presence of salivary pellicles between hard surfaces reduces the friction coefficient by a factor of 20. This reduction of friction is consistent with the long-range purely repulsive nature of the normal forces acting between the salivary films. The lubricating mechanism is presumably based on a full separation of the sliding surfaces by the salivary films. The friction between salivary films has been investigated at normal loads that cover the clinical jaw closing forces, and it can be concluded that the lubricating properties are maintained within this load interval. The present study indicates the usefulness of colloidal probe AFM, which offers a direct and quantitative measure of lubrication at a molecular level, in the study of biotribological phenomena. In particular, the results obtained here may have implications for the development of saliva substitutes.     

Self-assembly of monoglycerides in beta-lactoglobulin adsorbed films at the air-water interface. Structural, topographical, and rheological consequences

In this work, we have analyzed the structural, topographical, and surface dilatational characteristics of pure beta-lactoglobulin adsorbed films and the effect of the self-assembly of monoglycerides (monopalmitin or monoolein) in beta-lactoglobulin films at the air-water interface. Measurements were performed in a single device that incorporates a Wilhelmy-type film balance, Brewster angle microscopy, and interfacial dilatational rheology. The structural and topographical characteristics of beta-lactoglobulin adsorbed and spread films are similar. However, the surface dilatational modulus of beta-lactoglobulin films shows a complex behavior depending on film formation. The self-assembly of monoglyceride in a beta-lactoglobulin adsorbed film has an effect on the structural, topographical, and dilatational properties of the mixed films, depending on the interfacial composition and the surface pressure (pi). At low pi, a mixed film of monoglyceride and beta-lactoglobulin may exist. At high pi (after the collapse of beta-lactoglobulin), the mixed films are dominated by monoglyceride molecules. However, the small amounts of collapsed beta-lactoglobulin have a significant effect on the surface dilatational properties of the mixed films. Protein displacement by monoglyceride is higher for monopalmitin than for monoolein. However, some degree of interaction exists between proteins and monoglycerides, and these interactions are more evident in adsorbed films than in spread films.     

Susceptibility of Fusobacterium nucleatum to killing by peroxidase-iodide-hydrogen peroxide combination in buffer solution and in human whole saliva

Some Gram-negative anaerobic bacteria have been associated with the infection of tooth supporting tissues, i.e. periodontitis. Of these bacteria, Fusobacterium nucleatum is sensitive to lactoperoxidase/myeloperoxidase-iodide-hydrogen peroxide system in vitro, but salivary concentrations of thiocyanate abolishes the bactericidality. These bacteria are located in periodontal pockets, on oral mucosa and in saliva. Although F. nucleatum most probably does not belong to the group of main periodontal pathogens, it sustains its proportion in the periodontal flora when gingivitis progresses to periodontitis. In this study, the sensitivity of F. nucleatum to different horseradish peroxidase-iodide-hydrogen peroxide combinations was tested both in buffer and in sterilized human whole saliva. Horseradish peroxidase was chosen because it does not bind thiocyanate at pH > or = 6. After 1h incubation at 37 degrees C, the cell viability was estimated by plate count and with flow cytometer using LIVE/DEAD BacLight kit (Molecular Probes, USA). In saliva, the horseradish peroxidase (50 microg/mL)-iodide (2.5 mM)-hydrogen peroxide (2.5 mM) combination decreased the amount of viable bacteria to 37% compared to 85% in the control without any of the components when measured with flow cytometer. Replacement of buffer by saliva decreased the bactericidality of the peroxidase system. However, in buffer less iodide and hydrogen peroxide was needed to produce significant decrease in the number of viable bacteria when measured by plate count than with flow cytometer. Our study shows that horseradish peroxidase-iodide-hydrogen peroxide combination is able to kill F. nucleatum cells in saliva. Horseradish peroxidase-iodide-hydrogen peroxide combination may be useful to diminish the degree of re-colonization of periodontitis-associated bacteria after periodontal therapy and to inhibit the transmission of these bacteria via saliva.     

Lubricating properties of the initial salivary pellicle--an AFM study

The role of saliva in the oral cavity is manifold; an important function is to serve as lubricant between hard (enamel) and soft (mucosal) tissues. Intraoral lubrication is of crucial importance in order to maintain functions such as deglutition, mastication and the faculty of speech. A large number of people suffer from impaired salivary functions, displaying symptoms such as 'dry mouth'. This results in a need for methods to assess the lubricating properties of both native saliva and potential artificial saliva formulations. Here, normal as well as lateral forces, acting between adsorbed salivary films, have been measured for the first time by means of colloidal probe atomic force microscopy (AFM). It was found that the presence of salivary pellicles between hard surfaces reduces the friction coefficient by a factor of 20. This reduction of friction is consistent with the long-range purely repulsive nature of the normal forces acting between the salivary films. The lubricating mechanism is presumably based on a full separation of the sliding surfaces by the salivary films. The friction between salivary films has been investigated at normal loads that cover the clinical jaw closing forces, and it can be concluded that the lubricating properties are maintained within this load interval. The present study indicates the usefulness of colloidal probe AFM, which offers a direct and quantitative measure of lubrication at a molecular level, in the study of biotribological phenomena. In particular, the results obtained here may have implications for the development of saliva substitutes.     

Normal and shear forces between surfaces bearing porcine gastric mucin, a high-molecular-weight glycoprotein

A surface force balance was used to measure the normal and shear forces between two mica surfaces each bearing an adsorbed layer of porcine gastric mucin ("Orthana" mucin), genetically similar to human MUC6. This mucin is a highly purified, 546 kDa, weakly negative, polyampholytic molecule with a "dumbbell" structure. Both bare (HP) and hydrophobized (HB) mica substrates were used, and forces were measured under 1 and 30 mg/mL mucin solutions, under pure (no-added-salt) water, and under 0.1 M aqueous Na(+) solution. Normal surface forces were monotonically repulsive in all cases, with onset of repulsion occurring at smaller surface separations, D, in the 0.1 M salt solutions (～ 20 nm, compared with ～40 nm for no added salt). Repulsion on HP mica was greater on surface compression than decompression, an effect, attributed to bridging and slow-relaxing additional adsorption on compression, not seen on HB mica, a difference attributed to the denser coverage of mucin hydrophobic moieties on the HB surface. Friction forces increased with compression in all cases, showing hysteretic behavior on HP but not on HB mica, commensurate with the hysteresis observed in the normal measurements. Low friction coefficients μ (= ?F(s)/?F(n) < 0.05) were seen up to mean pressures

≈ 0.5 to 1.0 MPa, attributed to low interpenetration of the opposed layers together with hydration lubrication effects, with higher μ (up to 0.4) at higher

attributed to interlayer entanglements and to bridging (for the case of HP mica). Shear forces increased only weakly with sliding speed over the range investigated (80-820 nm s(-1)). The lower friction with HB relative to HP mica suggests a selectivity of the HB surface to the hydrophobic moieties of the mucin that in consequence exposes relatively more of the better-lubricating hydrophilic groups. This surface-selectivity effect on lubrication may have a generality extending to other biological macromolecules that contain both hydrophilic and hydrophobic groups.     

Adsorption of a strong polyelectrolyte to model lignin surfaces

The adsorption of a strong, highly charged cationic polyelectrolyte to a kraft lignin thin film was investigated as a function of the adsorbing solution conditions using the quartz crystal microbalance. The polyelectrolyte, PDADMAC, with a molecular weight of 100 kDa and one cationic charge group per monomer, was adsorbed to the anionically charged lignin film in the pH range 3.5-9.5 in electrolyte solution of 0.1 to 100 mM NaCl. At low pH, the adsorbed amount of PDADMAC was minimal, however, this increased as a function of increasing pH. Indeed, the surface excess increased significantly at about pH 8.5, where ionization of the phenolic groups on the lignin macromolecule may be expected. Furthermore, at this elevated pH, the adsorbed amount of PDADMAC decreased as the ionic strength of the solution increased above 1 mM. This is due to the competitive adsorption of counterions to the lignin surface and indicates that the adsorption of PDADMAC to lignin is of a pure electrosorption nature.     

Oral mucosal pellicle. Adsorption and transpeptidation of salivary components to buccal epithelial cells.

The present investigation was carried out to examine the mechanism(s) whereby salivary molecules interact with human buccal epithelial cells. By utilizing antiserum against human parotid saliva, selected salivary components were detected by electrophoretic-transfer analysis of 1.5% SDS extracts of epithelial cells. Incubation of the cells and their aqueous cell-free extracts with 125I-labelled parotid saliva resulted in the formation of an iodinated high-molecular-mass complex which was not present in 125I-labelled saline alone. Formation of this complex was time-dependent and was inhibited by treating the buccal epithelial cells or their cell-free extracts with EGTA, iodoacetamide, N-ethylmaleimide or by heating at 100 degrees C for 15 min. The epithelial cells also promoted incorporation of [14C]putrescine into high-molecular-mass complexes whose formation was inhibited by iodoacetamide, unlabelled putrescine and EGTA. Cell extracts mediated cross-linking of monodansylcadaverine into alpha-casein, and this interaction was inhibited by iodoacetamide. Significant amounts of radioactivity were recovered with the epithelial-cell envelopes after exhaustive extraction of 125I-saliva- or [14C]putrescine-treated epithelial cells with 4% (w/v) SDS/10% (v/v) beta-mercaptoethanol. The incorporation of radioactivity into epithelial-cell envelopes was inhibited by pretreatment of the cells with putrescine, EGTA, iodoacetamide, or heating at 100 degrees C for 15 min. These data suggest that: (1) oral mucosal pellicle is formed by the selective adsorption of saliva to the epithelial-cell plasma membrane and its associated cytoskeleton; and (2) the adsorbed salivary components may be cross-linked to each other or the epithelial cytoskeleton by epithelial transglutaminases.     

Human saliva forms a complex film structure on alumina surfaces

Films formed from saliva on surfaces are important for the maintenance of oral health and integrity by protection against chemical and/or biological agents. The aim of the present study was to investigate adsorbed amounts, thickness, and structure of films formed from human whole saliva on alumina surfaces by means of in situ ellipsometry, neutron reflectivity, and atomic force microscopy. Alumina (Al2O3, synthetic sapphire) is a relevant and interesting substrate for saliva adsorption studies as it has an isoelectric point close to that of tooth enamel. The results showed that saliva adsorbs rapidly on alumina. The film could be modeled in two layers: an inner and dense thin region that forms a uniform layer and an outer, more diffuse and thicker region that protrudes toward the bulk of the solution. The film morphology described a uniformly covering dense layer and a second outer layer containing polydisperse adsorbed macromolecules or aggregates.