A Transtracheal Catheter for Recording the Static Tracheal Pressure in the Exercising Horse

After giving an account of the principles of pressure measurement in flowing air and a review of the literature on tracheal catheters, the authors describe the construction, the introduction and the function of their own transtracheal catheter. This is a teflon catheter with several side–ports which is introduced into the cervical trachea by a guide technique. After introduction, the catheter is stiffened by the insertion of 2 steel wires. The catheter was studied in model experiments concerning: a) the ability to measure the static pressure in flowing air, and b) the dynamic accuracy of a recording system built up around the catheter. The results indicated that the intratracheal pressure sensed in exercising horses well reflected the static pressure, and that the dynamic accuracy of the recording system was good to about 60 Hz. The present technique of recording the intratracheal pressure was used on 122 occasions in 69 exercising horses with only one complication referable to the catheter occurring. The transtracheal route of catheterisation may be superior, as catheters introduced by this route do not appear to influence the function of the pharynx and larynx. In contrast, nasotracheal catheters that traverse the larynx, might interfere with the respiratory function. kw|Keywords|k]upper airway obstruction k]frequency response     

Variations of stiffness and strength along the human cervical spine

The load-displacement response and strength of the mid (C2-C5) and lower (C5-T1) cervical regions were determined for combinations of sagittal loads, in vitro. In unpaired t-test comparisons, the mid cervical region was significantly stiffer in compression and extension than the lower region. In tests to failure, failure in six out of seven mid cervical specimens resulted from flexion alone, while combined compression-flexion was required to fail five of the eight lower cervical specimens. Post-test dissections revealed no regional differences in the pattern of failure. In addition to sagittal tests, the load-displacement responses of three-vertebrae cervical specimens were measured with the upper body axially rotated with respect to the lower body. The effect of this pre-torsion was to diminish the zone of low slope near zero load for axial, shear, and flexion motion. Three of the four axially rotated specimens failed in flexion without added compression. These controlled load-displacement measurements of cervical spine specimens describe for the first time the continuous flexion-compression response up to failure, and suggest that consideration of the biomechanics of three apparently distinct mobile regions of the cervical spine (C1-C2, C2-C5, C5-T1) may facilitate the interpretation of hazardous conditions and the diagnosis of injury. These data also provide basic information for the in vitro investigation of passive cervical spine protection such as helmets and head-rests, suggesting that the head should be kept in a non-rotated position to reduce risk of injury.     

Developmental biomechanics of the cervical spine: Tension and compression

Epidemiological data and clinical indicia reveal devastating consequences associated with pediatric neck injuries. Unfortunately, neither injury prevention nor clinical management strategies will be able to effectively reduce these injuries or their effects on children, without an understanding of the cervical spine developmental biomechanics. Thus, we investigated the relationship between spinal development and the functional (stiffness) and failure biomechanical characteristics of the cervical spine in a baboon model. A correlation study design was used to define the relationships between spinal tissue maturation and spinal biomechanics in both tension and compression. Eighteen baboon cervical spine specimens distributed across the developmental spectrum (1–26 human equivalent years) were dissected into osteoligamentous functional spinal units. Using a servo-hydraulic MTS, these specimens (Oc–C2, C3–C4, C5–C6, C7–T1) were non-destructively tested in tension and compression and then displaced to failure in tension while measuring the six-axes of loads and displacements. The functions describing the developmental biomechanical response of the cervical spine for stiffness and normalized stiffness exhibited a significant direct relationship in both tension and compression loading. Similarly, the tensile failure load and normalized failure load demonstrated significant maturational increases. Further, differences in biomechanical response were observed between the spinal levels examined and all levels exhibited clinically relevant failure patterns. These data support our understanding of the child cervical spine from a developmental biomechanics perspective and facilitate the development of injury prevention or management schema for the mitigation of child spine injuries and their deleterious effects.     

Ultrasonic measurement of depth-dependent transient behaviors of articular cartilage under compression

We previously reported an ultrasound method for measuring the depth-dependent equilibrium mechanical properties of articular cartilage using quasi-static compression. The objective of this paper was to introduce our recent development for nondestructively measuring the transient depth-dependent strains of full-thickness articular cartilage specimens prepared from bovine patellae. A 50 MHz focused ultrasound transducer was used to collect ultrasound echoes from articular cartilage specimens (n=8) and sponge phantoms with open pores (n=10) during tests of compression and subsequent stress-relaxation. The transient displacements of the tissues at different depths along the compression direction were calculated from the ultrasound echoes using a cross-correlation tracking technique. An LVDT sensor and a load cell were used to measure the overall deformation of the tissue and the applied force, respectively. Results showed that the tissues inside the cartilage layer continued to move during the stress-relaxation phase after the compression was completed. In the equilibrium state, the displacements of the cartilage tissues at the depths of 1/4, 1/2, and 3/4 of the full-thickness reduced by 51%+/-22%, 54%+/-17%, and 50+/-17%, respectively, in comparison with its peak value. However, no similar phenomenon was observed in the sponge phantoms. Our preliminary results demonstrated that this ultrasound method may provide a potential tool for the nondestructive measurement of the transient depth-dependent processes involved in biological and bioengineered soft tissues as well as soft biomaterials under dynamic loading.     

Development of a pressure-measuring device to optimize compression treatment of lymphedema and evaluation of change in garment pressure with simulated wear and tear

The use of compression garments in treating lymphedema following treatment of genital (penis, testes, uterus, cervical) and breast cancer treatment is a well-established practice. Although compression garments are classified in compression classes, little is known about the actual subgarment pressure exerted along the extremity. The aims of this study were to establish an in vitro method for measuring subgarment pressure along the extremity and to analyze initial and over time subgarment pressure of compression garments from three manufacturers. The measurements were performed with I-scan(?) (Tekscan Inc.) pressure measuring equipment once a week during a period of 4 weeks. Wear and tear was simulated by washing and putting on the garments on plastic legs every day. There was a statistically significant difference between the garments of some of manufacturers. There was no difference between garments from the same manufacturer. No significant decrease of subgarment pressure was observed during the trial period. The study demonstrated that Tekscan pressure-measuring equipment could measure subgarment pressure in vitro. The results may indicate that there was a difference in subgarment pressure exerted by garments from different manufacturers and that there was no clear decrease in subgarment pressure during the first four weeks of usage.     

Lung volume dependence of esophageal pressure in the neck

There is conflicting evidence in the literature regarding tissue pressure in the neck. We studied esophageal pressure along cervical and intrathoracic esophageal segments in six healthy men to determine extramural pressure for the cervical and intrathoracic airways. A balloon catheter system with a 1.5-cm-long balloon was used to measure intraesophageal pressures. It was positioned at 2-cm intervals, starting 10 cm above the cardiac sphincter and ending at the cricopharyngeal sphincter. We found that esophageal pressures became more negative as the balloon catheter moved from intrathoracic to cervical segments, until the level of the cricopharyngeal sphincter was reached. At total lung capacity, esophageal pressures were -10.5 +/- 2.9 (SE) cmH2O in the lower esophagus, -18.9 +/- 3.0 just within the thorax, and -21.3 +/- 2.73 within 2 cm of the cricopharyngeal sphincter. The variation in mouth minus esophageal pressure with lung volume was similar in cervical and thoracic segments. We conclude that the subatmospheric tissue pressure applied to the posterior membrane of the cervical trachea results in part from transmission of apical pleural pressure into the neck. Transmural pressure for cervical and thoracic tracheal segments is therefore similar.     

Human papillomavirus mutational insertion: specific marker of circulating tumor DNA in cervical cancer patients

Introduction

In most cases of cervical cancers, HPV DNA is integrated into the genome of carcinoma cells. This mutational insertion constitutes a highly specific molecular marker of tumor DNA for every patient. Circulating tumor DNA (ctDNA) is an emerging marker of tumor dynamics which detection requires specific molecular motif. To determine whether the sequence of the cell-viral junction could be used in clinical practice as a specific marker of ctDNA, we analyzed a series of cervical cancer patient serums.

Methods and Findings

Serum specimens of 16 patients diagnosed with HPV16/18-associated cervical cancer, and for which the viral integration locus had been previously localized, were analyzed. Sequential serum specimens, taken at different times during the course of the disease, were also available for two of these cases. ctDNA was found in 11 out of 13 patients with tumor size greater than 20 mm at diagnosis, and analysis of sequential serum specimens showed that ctDNA concentration in patients serum was related to tumor dynamics.

Conclusions

We report that HPV mutational insertion constitutes a highly specific molecular marker of ctDNA in HPV-associated tumor patients. Using this original approach, ctDNA was detected in most cervical cancer patients over stage I and ctDNA concentration was found to reflect tumor burden. In addition to its potential prognostic and predictive value, HPV mutation insertion is likely to constitute a new molecular surrogate of minimal residual disease and of subclinical relapse in HPV-associated tumor. This is of major importance in the perspective of specific anti-HPV therapy.     

Influence of follower load application on moment-rotation parameters and intradiscal pressure in the cervical spine

The objective of this study was to implement a follower load (FL) device within a robotic (universal force-moment sensor) testing system and utilize the system to explore the effect of FL on multi-segment cervical spine moment-rotation parameters and intradiscal pressure (IDP) at C45 and C56. Twelve fresh-frozen human cervical specimens (C3-C7) were biomechanically tested in a robotic testing system to a pure moment target of 2.0 Nm for flexion and extension (FE) with no compression and with 100 N of FL. Application of FL was accomplished by loading the specimens with bilateral cables passing through cable guides inserted into the vertebral bodies and attached to load controlled linear actuators. FL significantly increased neutral zone (NZ) stiffness and NZ width but resulted in no change in the range of motion (ROM) or elastic zone stiffness. C45 and C56 IDP measured in the neutral position were significantly increased with application of FL. The change in IDP with increasing flexion rotation was not significantly affected by the application of FL, whereas the change in IDP with increasing extension rotation was significantly reduced by the application of FL. Application of FL did not appear to affect the specimen’s quantity of motion (ROM) but did affect the quality (the shape of the curve). Regarding IDP, the effects of adding FL compression approximates the effect of the patient going from supine to a seated position (FL compression increased the IDP in the neutral position). The change in IDP with increasing flexion rotation was not affected by the application of FL, but the change in IDP with increasing extension rotation was, however, significantly reduced by the application of FL.     

Contact pressure in the facet joint during sagittal bending of the cadaveric cervical spine

The facet joint contributes to the normal biomechanical function of the spine by transmitting loads and limiting motions via articular contact. However, little is known about the contact pressure response for this joint. Such information can provide a quantitative measure of the facet joint's local environment. The objective of this study was to measure facet pressure during physiologic bending in the cervical spine, using a joint capsule-sparing technique. Flexion and extension bending moments were applied to six human cadaveric cervical spines. Global motions (C2-T1) were defined using infra-red cameras to track markers on each vertebra. Contact pressure in the C5-C6 facet was also measured using a tip-mounted pressure transducer inserted into the joint space through a hole in the postero-inferior region of the C5 lateral mass. Facet contact pressure increased by 67.6 ± 26.9 kPa under a 2.4 Nm extension moment and decreased by 10.3 ± 9.7 kPa under a 2.7 Nm flexion moment. The mean rotation of the overall cervical specimen motion segments was 9.6 ± 0.8° and was 1.6 ± 0.7° for the C5-C6 joint, respectively, for extension. The change in pressure during extension was linearly related to both the change in moment (51.4 ± 42.6 kPa/Nm) and the change in C5-C6 angle (18.0 ± 108.9 kPa/deg). Contact pressure in the inferior region of the cervical facet joint increases during extension as the articular surfaces come in contact, and decreases in flexion as the joint opens, similar to reports in the lumbar spine despite the difference in facet orientation in those spinal regions. Joint contact pressure is linearly related to both sagittal moment and spinal rotation. Cartilage degeneration and the presence of meniscoids may account for the variation in the pressure profiles measured during physiologic sagittal bending. This study shows that cervical facet contact pressure can be directly measured with minimal disruption to the joint and is the first to provide local pressure values for the cervical joint in a cadaveric model.     

数字化骨科理念辅助椎弓根置钉在寰枢椎不稳中的临床应用

目的:探讨3D打印辅助置钉技术用于寰枢椎不稳椎弓根置钉的安全性及准确性。方法:收集2013年1月到2015年1月西安交通大学第一附属医院收治的寰枢椎不稳病例,术前采用3D打印技术构建个体化3D打印模型,在模型上模拟置钉,获取最佳置钉点、置钉角度等个体化置钉数据,并于术中辅助椎弓根螺钉置入。通过CT扫描评价置钉准确性,测量术前、术后患者寰齿间隙判断寰枢椎复位情况,测量颈延角评价脊髓压迫改善情况,并采用日本骨科学会(JOA)评分判断患者脊髓功能改善情况。术后定期随访观察固定效果、稳定性、神经损伤等手术并发症的发生情况。结果:13例患者均采用3D打印辅助置钉技术进行内固定治疗,手术顺利,术中及术后无血管、神经损伤等并发症,复位及内固定效果满意。共置入椎弓根螺钉31枚,其中29枚完全在椎弓根内,置钉准确率为93.5%。寰枢椎较术前明显复位,术后寰齿间隙、颈延角和JOA评分较术前明显改善,差异具有统计学意义(P0.05)。结论:3D打印技术辅助上颈椎椎弓根置钉的准确性及安全性均较高。     

Construction and Accuracy Assessment of Patient-Specific Biocompatible Drill Template for Cervical Anterior Transpedicular Screw (ATPS) Insertion: An In Vitro Study

Background

With the properties of three-column fixation and anterior-approach-only procedure, anterior transpedicular screw (ATPS) is ideal for severe multilevel traumatic cervical instabilities. However, the accurate insertion of ATPS remains challenging. Here we constructed a patient-specific biocompatible drill template and evaluated its accuracy in assisting ATPS insertion.

Methods

After ethical approval, 24 formalin-preserved cervical vertebrae (C2–C7) were CT scanned. 3D reconstruction models of cervical vertebra were obtained with 2-mm-diameter virtual pin tracts at the central pedicles. The 3D models were used for rapid prototyping (RP) printing. A 2-mm-diameter Kirschner wire was then inserted into the pin tract of the RP model before polymethylmethacrylate was used to construct the patient-specific biocompatible drill template. After removal of the anterior soft tissue, a 2-mm-diameter Kirschner wire was inserted into the cervical pedicle with the assistance of drill template. Cadaveric cervical spines with pin tracts were subsequently scanned using the same CT scanner. A 3D reconstruction was performed of the scanned spines to get 3D models of the vertebrae containing the actual pin tracts. The deviations were calculated between 3D models with virtual and actual pin tracts at the middle point of the cervical pedicle. 3D models of 3.5 mm-diameter screws were used in simulated insertion to grade the screw positions.

Findings

The patient-specific biocompatible drill template was constructed to assist ATPS insertion successfully. There were no significant differences between medial/lateral deviations (P = 0.797) or between superior/inferior deviations (P = 0.741). The absolute deviation values were 0.82±0.75 mm and 1.10±0.96 mm in axial and sagittal planes, respectively. In the simulated insertion, the screws in non-critical position were 44/48 (91.7%).

Conclusions

The patient-specific drill template is biocompatible, easy-to-apply and accurate in assisting ATPS insertion. Its clinical applications should be further researched.     

Presence of human papillomavirus DNA sequences in cervical intraepithelial neoplasia.

Twenty two patients referred to a district colposcopy clinic because of an abnormal cervical cytology report or a suspicious cervix and found to have a cervical epithelial abnormality were studied. The techniques of cytology, histology, immunohistochemistry, and DNA-DNA hybridisation were used to detect infection by human papillomavirus. Using an indirect immunoalkaline phosphatase technique human papillomavirus antigen was found in biopsy specimens from six of the 22 patients and DNA of papillomavirus type 6 in biopsy specimens from 13 of these women, including four out of six whose histological diagnosis was cervical intraepithelial neoplasia grade 3. In eight cases where cytological, colposcopical, and histological investigations all indicated the presence of wart virus infection, papillomavirus type 6 DNA was found in seven. Papillomavirus type 6 DNA was found in more than half of the proved cases of cervical intraepithelial neoplasia. The presence of this viral DNA in women with no cervical abnormality is to be studied.     

Human papillomavirus testing with a liquid-based system: feasibility and comparison with reference diagnoses

OBJECTIVE: To validate the utilization of cervical specimens collected in the fixative liquid used in the CYTO-screen System (SEROA, Monaco) for oncogenic human papillomavirus (HPV) DNA detection by the Hybrid Capture II technique (HCII) (Digene, Gaithersburg, Maryland, U.S.A) by reference to cytologic and/or histologic results. STUDY DESIGN: A technical feasibility study was conducted on 3 modalities of sample preparation before HCII technique, 1 with a proteinase digestion, I with PBS washing and I using the Digene sample conversion kit recommended for ThinPrep medium preparation (Cytyc Corp., Boxborough, Massachusetts, U.S.A.). The stability of cells after storage at days 28, 60 and 90 was tested on 26 positive samples (13 with high initial indices and 13 with low initial indices). Results of HPV testing were compared to cytologic and histologic results on a sample of 98 smears already identified as high grade squamous intraepithelial lesion (HSIL) (48) or low grade squamous intraepithelial lesion (LSIL) (50). A retrospective analysis was then performed on 995 HPV tests perfornmed routinely in 2003 in terms of comparison with the corresponding cytologic and/or histologic results. RESULTS: The HCII technique after direct treatment by proteinase K appeared to be as effective as the Digene sample conversion kit. By using the first technique, all 26 positive cases remained positive at 60 days, but 4 of 13 (30%) with low indices became negative at 90 days. The sensitivity of HPV testing for detecting biopsy- proven cervical intraepithelial neoplasia (CIN) 2 or worse was 100% in the 50 LSIL and 98% in the 48 HSIL samples. In the retrospective study (n = 995), the cytologic diagnoses of atypical squamous cells of undetermined significance (ASC-US) (n=278), LSIL (n = 137) and HSIL (n = 28) were associated with a positive HPVtest in 44%, 75% and 96% of cases, respectively. On a subsample of 156 patients among 278 with a diagnosis of ASC- US, the sensitivity of HPV testingfor detecting CIN 2 or worse was 88%, specificity 57%, positive predictive value 10% and negative predictive value 99%. Performing HPV testing by the HCII technique for cervical specimens collected in the fixative liquid used in the CYTO-screen System is feasible in the context of an ASC-US cytologic diagnosis.     

Investigation of impact loading rate effects on the ligamentous cervical spinal load-partitioning using finite element model of functional spinal unit C2–C3

The cervical spine functions as a complex mechanism that responds to sudden loading in a unique manner, due to intricate structural features and kinematics. The spinal load-sharing under pure compression and sagittal flexion/extension at two different impact rates were compared using a bio-fidelic finite element (FE) model of the ligamentous cervical functional spinal unit (FSU) C2–C3. This model was developed using a comprehensive and realistic geometry of spinal components and material laws that include strain rate dependency, bone fracture, and ligament failure. The range of motion, contact pressure in facet joints, failure forces in ligaments were compared to experimental findings. The model demonstrated that resistance of spinal components to impact load is dependent on loading rate and direction. For the loads applied, stress increased with loading rate in all spinal components, and was concentrated in the outer intervertebral disc (IVD), regions of ligaments to bone attachment, and in the cancellous bone of the facet joints. The highest stress in ligaments was found in capsular ligament (CL) in all cases. Intradiscal pressure (IDP) in the nucleus was affected by loading rate change. It increased under compression/flexion but decreased under extension. Contact pressure in the facet joints showed less variation under compression, but increased significantly under flexion/extension particularly under extension. Cancellous bone of the facet joints region was the only component fractured and fracture occurred under extension at both rates. The cervical ligaments were the primary load-bearing component followed by the IVD, endplates and cancellous bone; however, the latter was the most vulnerable to extension as it fractured at low energy impact.     

Acriflavine-Feulgen stilbene staining: a procedure for automated cervical cytology with a television based system (LEYTAS).

A sample preparation and staining procedure for automated cytology with a TV based system (LEYTAS) is described. It consists of a centrifugation technique and automated acriflavine-Feulgen stilbene staining of cervical specimens. The advantages of using both the fluorescence and the absorption image of acriflavine-Feulgen stilbene stained cervical cells for a television based system are discussed.     

A Rat Model of Ventricular Fibrillation and Resuscitation by Conventional Closed-chest Technique

A rat model of electrically-induced ventricular fibrillation followed by cardiac resuscitation using a closed chest technique that incorporates the basic components of cardiopulmonary resuscitation in humans is herein described. The model was developed in 1988 and has been used in approximately 70 peer-reviewed publications examining a myriad of resuscitation aspects including its physiology and pathophysiology, determinants of resuscitability, pharmacologic interventions, and even the effects of cell therapies. The model featured in this presentation includes: (1) vascular catheterization to measure aortic and right atrial pressures, to measure cardiac output by thermodilution, and to electrically induce ventricular fibrillation; and (2) tracheal intubation for positive pressure ventilation with oxygen enriched gas and assessment of the end-tidal CO₂. A typical sequence of intervention entails: (1) electrical induction of ventricular fibrillation, (2) chest compression using a mechanical piston device concomitantly with positive pressure ventilation delivering oxygen-enriched gas, (3) electrical shocks to terminate ventricular fibrillation and reestablish cardiac activity, (4) assessment of post-resuscitation hemodynamic and metabolic function, and (5) assessment of survival and recovery of organ function. A robust inventory of measurements is available that includes – but is not limited to – hemodynamic, metabolic, and tissue measurements. The model has been highly effective in developing new resuscitation concepts and examining novel therapeutic interventions before their testing in larger and translationally more relevant animal models of cardiac arrest and resuscitation.     

Stiffness behaviour of trabecular bone specimens

Trabecular bone specimens were tested by non-destructive technique with the purpose of investigating stiffness behaviour and optimizing stiffness determination. Cylindrical specimens (n = 25) were loaded repetitively (0.1 Hz, 30 cycles) by axial compression to 50% of predicted ultimate strength and finally compressed to failure. Analyses of single compression curves showed increasing stiffness (E') until a stress level about 50% of ultimate stress followed by decreasing stiffness. Curve fit analysis of the elastic part of the compression curve showed the best fit, when a second order polynomial was used (r = 0.94, p less than 0.001). The stiffness determined non-destructively at the 25% level of ultimate strength increased significantly to the tenth loading cycle followed by a steady state. The precision of stiffness determination as an average of five consecutive measurements at steady state was E' +/- less than 5% (95% confidence limits). A reproducibility test by repetition of the test sequence after 3 h rest showed qualitatively the same stiffness behaviour. The variation of stiffness determination between the two test sequences was +/- 27% at the first loading cycle falling to +/- 12% at steady state.     

A precise radiographic technique for the measurement of dimensional changes in heart valve biomaterials following fixation

Accurate tissue thickness measurements are difficult to acquire by present techniques. Error is introduced by tissue compression during measurements or by tissue processing prior to measurement. In the field of valve replacement, tissue dimensional changes from fixation prior to implantation may predispose implants to premature tissue failure and it becomes important to have an accurate method for comparing cusp dimensions pre- and post-fixation. A new approach is to use high-resolution digital radiography to make thickness maps of entire specimens. For 25 matched porcine aortic valve cusps, we have evaluated this technique's ability to measure and compare thickness, surface area and volume before and after 7 days of aldehyde fixation. Digital radiographs were acquired pre- and post-0.5% glutaraldehyde (n=13) or 10% formaldehyde (n=12) fixation. Mean thickness, surface area, volume and four measurements to evaluate shape differences with fixation were obtained and compared pre- and post-fixation using paired t tests. The results demonstrate that this X-ray imaging technique can provide dimensions of matched fresh and fixed specimens and is sensitive enough to show statistically significant changes due to fixation. These findings also illustrate that aldehyde fixation can cause tissue contraction resulting in a significant overall increase in tissue thickness and a decrease in surface area. This technique could be used to gain further insights into tissue anatomy and mechanics.     

Study on effect of diluent osmotic pressure on yeast cell strength and cell size using a novel micromanipulation technique

A new micromanipulation technique which has previously been used to measure the mechanical properties of single animal cells has now been applied to yeast cells. In this study this technique was used to measure yeast cell strength and cell size across a 2l batch fermentation. Alternatively the cell size could also be determined using a Coulter counter while cell measurement was diluted with a conducting fluid (Isoton II). For the cell strength, it was found that the osmotic pressure of diluents did affect cell strength. However, it was also found that there was no significant effect of osmotic pressure of diluents on cell size whether a Coulter counter or micromanipulation was used for measurement. Micromanipulation has been shown to be a powerful technique for measuring the mechanical properties of yeast cells and it will be very useful for studying their behaviour in cell disruption equipment, e.g. high-pressure homogenizers.     

Changes in tracheal cross-sectional area during Mueller and Valsalva maneuvers in humans

Pressure-area behavior of the excised trachea is well documented, but little is known of tracheal compliance in vivo. Extratracheal tissue pressures are not directly measurable, but transmural pressure for the intrathoracic trachea is inferred from intra-airway and pleural pressure differences. Extramural pressure of the cervical trachea is assumed to be atmospheric. The difference in transmural pressure between the intra- and extrathoracic tracheal segments should be exaggerated during Mueller and Valsalva maneuvers. We used the acoustic reflection technique to measure tracheal areas above and below the thoracic inlet during these isovolume-pressure maneuvers. We found that 10 cmH2O positive pressure increased tracheal area in the extrathoracic segment by 34 +/- 16% (mean +/- SD) and in the intrathoracic segment by 35 +/- 15%. There was a reduction in area of 27 +/- 16 and 24 +/- 14%, respectively, for the extra- and intrathoracic segments with 10 cmH2O negative pressure. We conclude that the effective transmural pressure gradients do not vary significantly between intra- and extrathoracic tracheal segments.