The influence of solid/liquid separation techniques on the sugar yield in two-step dilute acid hydrolysis of softwood followed by enzymatic hydrolysis

Background  

Two-step dilute acid hydrolysis of softwood, either as a stand-alone process or as pretreatment before enzymatic hydrolysis, is considered to result in higher sugar yields than one-step acid hydrolysis. However, this requires removal of the liquid between the two steps. In an industrial process, filtration and washing of the material between the two steps is difficult, as it should be performed at high pressure to reduce energy demand. Moreover, the application of pressure leads to more compact solids, which may affect subsequent processing steps. This study was carried out to investigate the influence of pressing the biomass, in combination with the effects of not washing the material, on the sugar yield obtained from two-step dilute acid hydrolysis, with and without subsequent enzymatic digestion of the solids.     

Improved one‐step steam pretreatment of SO2‐Impregnated softwood with time‐dependent temperature profile for ethanol production

In the production of ethanol from lignocellulosic material, pretreatment of the raw material before enzymatic hydrolysis and fermentation is essential to obtain high overall yields of sugar and ethanol. Two‐step steam pretreatment results in higher ethanol yields from softwood than the standard one‐step pretreatment process. However, the difficulty with separation and washing of the material at high pressure between the two pretreatment steps is a major drawback. In this study, a new one‐step pretreatment procedure was investigated, in which the time‐temperature profile was varied during pretreatment. The efficiency of pretreatment was assessed by performing simultaneous saccharification and fermentation on the pretreated slurries. Pretreatment of SO₂‐impregnated softwood performed by varying the temperature (190–226°C), the residence time (5–10 min), and the mode of temperature increase (linear or stepwise), resulted in recovery of about 90% of the mannose and glucose present in the raw material. The highest ethanol yield, 75% of theoretical based on the glucan and mannan content of the raw material, was obtained at pretreatment conditions of 190°C for 12 min. Similar ethanol yields were achieved when running the pretreatment as one‐step (190–200°C), two levels of temperature, at shorter residence time (7 min), which results in lower capital costs for the process. © 2010 American Institute of Chemical Engineers Biotechnol. Prog., 2010     

Steam pretreatment of H(2)SO(4)-impregnated Salix for the production of bioethanol

In the bioconversion of lignocellulosic materials to ethanol, pretreatment of the material prior to enzymatic hydrolysis is essential to obtain high overall yields of sugar and ethanol. In this study, steam pretreatment of fast-growing Salix impregnated with sulfuric acid has been investigated by varying the temperature (180-210 degrees C), the residence time (4, 8 or 12 min), and the acid concentration (0.25% or 0.5% (w/w) H(2)SO(4)). High sugar recoveries were obtained after pretreatment, and the highest yields of glucose and xylose after the subsequent enzymatic hydrolysis step were 92% and 86% of the theoretical, respectively, based on the glucan and xylan contents of the raw material. The most favorable pretreatment conditions regarding the overall sugar yield were 200 degrees C for either 4 or 8 min using 0.5% sulfuric acid, both resulting in a total of 55.6g glucose and xylose per 100g dry raw material. Simultaneous saccharification and fermentation experiments were performed on the pretreated slurries at an initial water-insoluble content of 5%, using ordinary baker's yeast. An overall theoretical ethanol yield of 79%, based on the glucan and mannan content in the raw material, was obtained.     

Optimizing pentose utilization in yeast: the need for novel tools and approaches

Background

The two-step dilute acid hydrolysis (DAH) of softwood is costly in energy demands and capital costs. However, it has the advantage that hydrolysis and subsequent removal of hemicellulose-derived sugars can be carried out under conditions of low severity, resulting in a reduction in the level of sugar degradation products during the more severe subsequent steps of cellulose hydrolysis. In this paper, we discuss a single-step DAH method that incorporates a temperature profile at two levels. This profile should simulate the two-step process while removing its major disadvantage, that is, the washing step between the runs, which leads to increased energy demand.

Results

The experiments were conducted in a reactor with a controlled temperature profile. The total dry matter content of the hydrolysate was up to 21.1% w/w, corresponding to a content of 15.5% w/w of water insoluble solids. The highest measured glucose yield, (18.3 g glucose per 100 g dry raw material), was obtained after DAH cycles of 3 min at 209°C and 6 min at 211°C with 1% H₂SO₄, which resulted in a total of 26.3 g solubilized C6 sugars per 100 g dry raw material. To estimate the remaining sugar potential, enzymatic hydrolysis (EH) of the solid fraction was also performed. EH of the solid residue increased the total level of solubilized C6 sugars to a maximum of 35.5 g per 100 g dry raw material when DAH was performed as described above (3 min at 210°C and 2 min at 211°C with 1% H₂SO₄).

Conclusion

The dual-temperature DAH method did not yield decisively better results than the single-temperature, one-step DAH. When we compared the results with those of earlier studies, the hydrolysis performance was better than with the one-step DAH but not as well as that of the two-step, single-temperature DAH. Additional enzymatic hydrolysis resulted in lower levels of solubilized sugars compared with other studies on one-step DAH and two-step DAH followed by enzymatic hydrolysis. A two-step steam pretreatment with EH gave rise to a considerably higher sugar yield in this study.     

Process considerations and economic evaluation of two-step steam pretreatment for production of fuel ethanol from softwood

To increase the overall ethanol yield from softwood, the steam pretreatment stage can be carried out in two steps. The two-step pretreatment process was evaluated from a techno-economic standpoint and compared with the one-step pretreatment process. The production plants considered were designed to utilize spruce as raw material and have a capacity of 200,000 tons/year. The two-step process resulted in a higher ethanol yield and a lower requirement for enzymes. However, the two-step process is more capital-intensive and has a higher energy requirement. The estimated ethanol production cost was the same, 4.13 SEK/L (55.1 cent /L) for both alternatives. For the two-step process different energy-saving options were considered, such as a higher concentration of water-insoluble solids in the filter cake before the second step, and the possibility of excluding the pressure reduction between the steps. The most optimistic configuration, with 50% water-insoluble solids in the filter cake in the feed to the second pretreatment step, no pressure reduction between the pretreatment steps, and 77% overall ethanol yield (0.25 kg EtOH/kg dry wood), resulted in a production cost of 3.90 SEK/L (52.0 cent /L). This shows the potential for the two-step pretreatment process, which, however, remains to be verified in pilot trials.     

Pretreatment efficiency and structural characterization of rice straw by an integrated process of dilute-acid and steam explosion for bioethanol production

The combined pretreatment of rice straw using dilute-acid and steam explosion followed by enzymatic hydrolysis was investigated and compared with acid-catalyzed steam explosion pretreatment. In addition to measuring the chemical composition, including glucan, xylan and lignin content, changes in rice straw features after pretreatment were investigated in terms of the straw's physical properties. These properties included crystallinity, surface area, mean particle size and scanning electron microscopy imagery. The effect of acid concentration on the acid-catalyzed steam explosion was studied in a range between 1% and 15% acid at 180°C for 2 min. We also investigated the influence of the residence time of the steam explosion in the combined pretreatment and the optimum conditions for the dilute-acid hydrolysis step in order to develop an integrated process for the dilute-acid and steam explosion. The optimum operational conditions for the first dilute-acid hydrolysis step were determined to be 165°C for 2 min with 2% H(2)SO(4) and for the second steam explosion step was to be carried out at 180°C for 20 min; this gave the most favorable combination in terms of an integrated process. We found that rice straw pretreated by the dilute-acid/steam explosions had a higher xylose yield, a lower level of inhibitor in the hydrolysate and a greater degree of enzymatic hydrolysis; this resulted in a 1.5-fold increase in the overall sugar yield when compared to the acid-catalyzed steam explosion.     

Effect of hemicellulose and lignin removal on enzymatic hydrolysis of steam pretreated corn stover

Ethanol can be produced from lignocellulosic biomass using steam pretreatment followed by enzymatic hydrolysis and fermentation. The sugar yields, from both hemicellulose and cellulose are critical parameters for an economically-feasible ethanol production process. This study shows that a near-theoretical glucose yield (96-104%) from acid-catalysed steam pretreated corn stover can be obtained if xylanases are used to supplement cellulases during hydrolysis. Xylanases hydrolyse residual hemicellulose, thereby improving the access of enzymes to cellulose. Under these conditions, xylose yields reached 70-74%. When pre-treatment severity was reduced by using autocatalysis instead of acid-catalysed steam pretreatment, xylose yields were increased to 80-86%. Partial delignification of pretreated material was also evaluated as a way to increase the overall sugar yield. The overall glucose yield increased slightly due to delignification but the overall xylose yield decreased due to hemicellulose loss in the delignification step. The data also demonstrate that steam pretreatment is a robust process: corn stover from Europe and North America showed only minor differences in behaviour.     

Enhancement of the enzymatic digestibility of sugarcane bagasse by steam pretreatment impregnated with hydrogen peroxide

Sugarcane bagasse was subjected to steam pretreatment impregnated with hydrogen peroxide. Analyses were performed using 2³ factorial designs and enzymatic hydrolysis was performed at two different solid concentrations and with washed and unwashed material to evaluate the importance of this step for obtaining high cellulose conversion. Similar cellulose conversion were obtained at different conditions of pretreatment and hydrolysis. When the cellulose was hydrolyzed using the pretreated material in the most severe conditions of the experimental design (210°C, 15 min and 1.0% hydrogen peroxide), and using 2% (w/w) water‐insoluble solids (WIS), and 15 FPU/g WIS, the cellulose conversion was 86.9%. In contrast, at a milder pretreatment condition (190°C, 15 min and 0.2% hydrogen peroxide) and industrially more realistic conditions of hydrolysis (10% WIS and 10 FPU/g WIS), the cellulose conversion reached 82.2%. The step of washing the pretreated material was very important to obtain high concentrations of fermentable sugars. © 2012 American Institute of Chemical Engineers Biotechnol. Prog., 2012     

Improved ethanol yield and reduced Minimum Ethanol Selling Price (MESP) by modifying low severity dilute acid pretreatment with deacetylation and mechanical refining: 1) Experimental

ABSTRACT: BACKGROUND: Historically, acid pretreatment technology for the production of bio-ethanol from corn stover has required severe conditions to overcome biomass recalcitrance. However, the high usage of acid and steam at severe pretreatment conditions hinders the economic feasibility of the ethanol production from biomass. In addition, the amount of acetate and furfural produced during harsh pretreatment is in the range that strongly inhibits cell growth and impedes ethanol fermentation. The current work addresses these issues through pretreatment with lower acid concentrations and temperatures incorporated with deacetylation and mechanical refining. RESULTS: The results showed that deacetylation with 0.1 M NaOH before acid pretreatment improved the monomeric xylose yield in pretreatment by up to 20 % while keeping the furfural yield under 2 %. Deacetylation also improved the glucose yield by 10 % and the xylose yield by 20 % during low solids enzymatic hydrolysis. Mechanical refining using a PFI mill further improved sugar yields during both low- and high-solids enzymatic hydrolysis. Mechanical refining also allowed enzyme loadings to be reduced while maintaining high yields. Deacetylation and mechanical refining are shown to assist in achieving 90 % cellulose yield in high-solids (20 %) enzymatic hydrolysis. When fermentations were performed under pH control to evaluate the effect of deacetylation and mechanical refining on the ethanol yields, glucose and xylose utilizations over 90 % and ethanol yields over 90 % were achieved. Overall ethanol yields were calculated based on experimental results for the base case and modified cases. One modified case that integrated deacetylation, mechanical refining, and washing was estimated to produce 88 gallons of ethanol per ton of biomass. CONCLUSION: The current work developed a novel bio-ethanol process that features pretreatment with lower acid concentrations and temperatures incorporated with deacetylation and mechanical refining. The new process shows improved overall ethanol yields compared to traditional dilute acid pretreatment. The experimental results from this work support the techno-economic analysis and calculation of Minimum Ethanol Selling Price (MESP) detailed in our companion paper.     

Optimization of ammonia fiber expansion (AFEX) pretreatment and enzymatic hydrolysis of Miscanthus x giganteus to fermentable sugars

Miscanthus x giganteus is a tall perennial grass whose suitability as an energy crop is presently being appraised. There is very little information on the effect of pretreatment and enzymatic saccharification of Miscanthus to produce fermentable sugars. This paper reports sugar yields during enzymatic hydrolysis from ammonia fiber expansion (AFEX) pretreated Miscanthus. Pretreatment conditions including temperature, moisture, ammonia loading, residence time, and enzyme loadings are varied to maximize hydrolysis yields. In addition, further treatments such as soaking the biomass prior to AFEX as well as washing the pretreated material were also attempted to improve sugar yields. The optimal AFEX conditions determined were 160 degrees C, 2:1 (w/w) ammonia to biomass loading, 233% moisture (dry weight basis), and 5 min reaction time for water-soaked Miscanthus. Approximately 96% glucan and 81% xylan conversions were achieved after 168 h enzymatic hydrolysis at 1% glucan loading using 15 FPU/(g of glucan) of cellulase and 64 p-NPGU/(g of glucan) of beta-glucosidase along with xylanase and tween-80 supplementation. A mass balance for the AFEX pretreatment and enzymatic hydrolysis process is presented.     

Explosive pretreatment of lignocellulosic residues with high-pressure carbon dioxide for the production of fermentation substrates

A new pretreatment technique has been developed in which the lignocellulosic material is subjected to the action of steam and high-pressure carbon dioxide before being explosively discharged through a defibrating nozzle of novel design. Operating at 200 degrees C and gas pressures in the range of 3.45-13.8 MPa, exploded products with maximum in vitro cellulase digestibilities of 81, 78, and 75% were obtained from wheat straw, bagasse, and Eucalyptus regnans woodchips, respectively. The treatment times required to obtain substrates of maximum digestibility were 5 min for wheat straw and bagasse and 15 min for E. regnans. Analysis of the exploded products indicated that the pretreatment had substantially removed and solubilized the hemicellulose fraction of the feed materials, giving an autohydrolysis liquor rich in xylose and a fibrous residue primarily composed of alpha-cellulose and lignin. The fibrous residue was readily amenable to cellulase hydrolysis, with saccharification being completed within 48 h. The theoretical energy demand for gas compression in the pretreatment process has been calculated at 11 k Wh/ton raw material when the digester is operated at 3.45 MPa and a packing density of 250 kg raw material/m(3) digester volume.     

Effects of preheating on briquetting and subsequent hydrothermal pretreatment for enzymatic saccharification of wheat straw

Briquetting of plant biomass with low bulk density is an advantage for handling, transport, and storage of the material, and heating of the biomass prior to the briquetting facilitates the densification process and improves the physical properties of the briquettes. This study investigates the effects of preheating prior to briquetting of wheat straw (WS) on subsequent hydrothermal pretreatment and enzymatic conversion to fermentable sugars. WS (11% moisture content) was densified to briquettes under different conditions; without preheating or with preheating at 75 or 125°C for either 5 or 10 min. Subsequent hydrothermal pretreatment was done for both un-briquetted WS and for briquettes. Enzymatic saccharification was afterwards performed for all samples. The results showed that as expected, nonpretreated WS briquettes gave very low sugar yields (22–29% of the cellulose content), even though preheating at 125°C prior to briquetting (without pretreatment) improved sugar yields somewhat. When combined with pretreatment, briquetting with preheating showed neutral or negative effects on sugar yield. This result suggests that moderate preheating (75°C for 5 min) before briquetting improved bulk density and compressive resistance of briquettes without impeding subsequent enzymatic conversion. However, excessive preheating (75 or 125°C for 10 min) before briquetting may result in irreversible structural modifications that hinder the interaction between biomass and water during pretreatment, thereby decreasing the accessibility of cellulose to enzymatic saccharification.     

Autocatalytic hydrothermal pretreatment by recycling byproduct organic acids to directionally depolymerize cassava straw

A two-stage autocatalytic hydrothermal pretreatment was proposed to improve the cassava straw utilization. The two-stage hydrothermal pretreatment was a process of which the first stage adopted lower-severity conditions (temperature and time) to improve the C-5 sugar yields and the second stage employed more severities to enhance C-6 sugar yield during enzyme hydrolysis. After employing this process, the maximum yields of C-5 and C-6 sugars were 68.49% and 81.02% when treating at 180 °C for 60 min for the first stage and 200 °C for 20 min for the second stage. Based on this, the autocatalytic pretreatment was investigated, which was a method to further enhance the pretreatment intensity by recycling pretreated liquid rich in byproduct organic acids (acetic acid, lactic acid and formic acid) during two-stage hydrothermal pretreatment. The results showed that the C-5 sugar yields of the first stage increased to 81.12% when recycled pretreated liquid twice, which led to 0.93 wt% byproduct organic acid. After the second stage, the C-6 sugar yield increased to 88.60% during enzymatic hydrolysis. Besides, mass balance and development potentials were analyzed. The results revealed that two-stage autocatalytic hydrothermal pretreatment could effectively enhance pretreatment intensity and provide promising methods of directionally depolymerizing cassava straws.     

Supercritical CO2 pretreatment of lignocellulose enhances enzymatic cellulose hydrolysis

The supercritical carbon dioxide (SC-CO2) pretreatment of lignocellulose for enzymatic hydrolysis of cellulose was investigated. Aspen (hardwood) and southern yellow pine (softwood) with moisture contents in the range of 0-73% (w/w) were pretreated with SC-CO2 at 3100 and 4000 psi and at 112-165 degrees C for 10-60 min. Each pretreated lignocellulose was hydrolyzed with commercial cellulase to assess its enzymatic digestibility. Untreated aspen and southern yellow pine (SYP) gave final reducing sugar yields of 14.5 +/- 2.3 and 12.8 +/- 2.7% of theoretical maximum, respectively. When no moisture was present in lignocellulose to be pretreated, the final reducing sugar yield from hydrolysis of SC-CO2-pretreated lignocellulose was similar to that of untreated aspen. When the moisture content of lignocellulose was increased, particularly in aspen, significantly increased final sugar yields were obtained from enzymatic hydrolysis of SC-CO2-pretreated lignocellulose. When the moisture content of lignocellulose was 73% (w/w) before pretreatment, the sugar yields from the enzymatic hydrolysis of aspen and southern yellow pine pretreated with SC-CO2 at 3100 psi and 165 degrees C for 30 min were 84.7 +/- 2.6 and 27.3 +/- 3.8% of theoretical maximum, respectively. The SC-CO2 pretreatments of both aspen and SYP with moisture contents of 40, 57, and 73% (w/w) showed significantly higher final sugar yields compared to the thermal pretreatments without SC-CO2.     

Fast and efficient alkaline peroxide treatment to enhance the enzymatic digestibility of steam-exploded softwood substrates.

The enzymatic digestibility of steam-exploded Douglas-fir wood chips (steam exploded at 195 degrees C, 4.5 min, and 4.5% (w/w) SO(2)) was significantly improved using an optimized alkaline peroxide treatment. Best hydrolysis yields were attained when the steam-exploded material was post-treated with 1% hydrogen peroxide at pH 11.5 and 80 degrees C for 45 min. This alkaline peroxide treatment was applied directly to the water-washed, steam-exploded material eliminating the need for independent alkali treatment with 0.4% NaOH, which has been traditionally used to post-treat wood samples to try to remove residual lignin. Approximately 90% of the lignin in the original wood was solubilized by this novel procedure, leaving a cellulose-rich residue that was completely hydrolyzed within 48 h, using an enzyme loading of 10 FPU/g cellulose. About 82% of the originally available polysaccharide components of the wood could be recovered. The 18% of the carbohydrate that was not recovered was lost primarily to sugar degradation during steam explosion.     

Efficacy of a hot washing process for pretreated yellow poplar to enhance bioethanol production

Cost reductions for pretreatment and bioconversion processes are key objectives necessary to the successful deployment of a bioethanol industry. These unit operations have long been recognized for their impact on the production cost of ethanol. One strategy to achieve this objective is to improve the pretreatment process to produce a pretreated substrate resulting in reduced bioconversion time, lower cellulase enzyme usage, and/or higher ethanol yields. Previous research produced a highly digestible pretreated yellow poplar substrate using a multistage, continuously flowing, very dilute sulfuric acid (0.07% (w/v)) pretreatment. This process reduced the time required for the bioconversion of pretreated yellow poplar sawdust to ethanol. This resulted in a substantially improved yield of ethanol from cellulose. However, the liquid volume requirements, steam demand, and complexity of the flow-through reactor configuration were determined to be serious barriers to commercialization of that process. A reconfigured process to achieve similar performance has been developed using a single-stage batch pretreatment followed by a separation of solids and liquids and washing of the solids at a temperatures between 130 and 150 degrees C. Separation and washing at the elevated temperature is believed to prevent a large fraction of the solubilized lignin and xylan from reprecipitating and/or reassociating with the pretreated solids. This washing of the solids at elevated temperature resulted in both higher recovered yields of soluble xylose sugars and a more digestible pretreated substrate for enzymatic hydrolysis. Key operating variables and process performance indicators included acid concentration, temperature, wash volume, wash temperature, soluble xylose recovery, and performance of the washed, pretreated solids in bioconversion via simultaneous saccharification and fermentation (SSF). Initial results indicated over a 50% increase in ethanol yield at 72 h for the hot washed material as compared to the control (no washing, no separation) and a 43% reduction of in the bioconversion time required for a high ethanol yield from cellulose     

Conversion of olive tree biomass into fermentable sugars by dilute acid pretreatment and enzymatic saccharification

The production of fermentable sugars from olive tree biomass was studied by dilute acid pretreatment and further saccharification of the pretreated solid residues. Pretreatment was performed at 0.2%, 0.6%, 1.0% and 1.4% (w/w) sulphuric acid concentrations while temperature was in the range 170-210 degrees C. Attention is paid to sugar recovery both in the liquid fraction issued from pretreatment (prehydrolysate) and that in the water-insoluble solid (WIS). As a maximum, 83% of hemicellulosic sugars in the raw material were recovered in the prehydrolysate obtained at 170 degrees C, 1% sulphuric acid concentration, but the enzyme accessibility of the corresponding pretreated solid was not very high. In turn, the maximum enzymatic hydrolysis yield (76.5%) was attained from a pretreated solid (at 210 degrees C, 1.4% acid concentration) in which cellulose solubilization was detected; moreover, sugar recovery in the prehydrolysate was the poorest one among all the experiments performed. To take account of fermentable sugars generated by pretreatment and the glucose released by enzymatic hydrolysis, an overall sugar yield was calculated. The maximum value (36.3 g sugar/100 g raw material) was obtained when pretreating olive tree biomass at 180 degrees C and 1% sulphuric acid concentration, representing 75% of all sugars in the raw material. Dilute acid pretreatment improves results compared to water pretreatment.     

Dilute sulfuric acid cycle spray flow-through pretreatment of corn stover for enhancement of sugar recovery

A cycle spray flow-through reactor was designed and used to pretreat corn stover in dilute sulfuric acid medium. The dilute sulfuric acid cycle spray flow-through (DCF) process enhanced xylose sugar yields and cellulose digestibility while increasing the removal of lignin. Within the DCF system, the xylose sugar yields of 90–93% could be achieved for corn stover pretreated with 2% (w/v) dilute sulfuric acid at 95 °C during the optimal reaction time (90 min). The remaining solid residue exhibited enzymatic digestibility of 90–95% with cellulase loading of 60 FPU/g glucan that was due to the effective lignin removal (70–75%) in this process. Compared with flow-through and compress-hot water pretreatment process, the DCF method produces a higher sugar concentration and higher xylose monomer yield. The novel DCF process provides a feasible approach for lignocellulosic material pretreatment.     

Hydrolysis of nonstarch carbohydrates of wheat-starch effluent for ethanol production

A (polysaccharide-rich) waste stream derived from a combined starch and ethanol factory was investigated regarding hydrolysis of the nonstarch carbohydrates for ethanol production. The material was characterized and processed to yield the maximum amount of sugars. The starch fraction was hydrolyzed with amylolytic enzymes, and the resulting fibrous material was separated by filtration. This material, denoted starch-free fibers (SFF), was subjected to heat treatment followed by enzymatic hydrolysis to recover the other major carbohydrate components, namely, cellulose and hemicellulose, in monomeric form. Heat treatment in a microwave oven efficiently solubilized a fraction of these polysaccharides and made the material more accessible to the cellulolytic and hemicellulolytic enzymes used in the subsequent enzymatic hydrolysis. The maximum sugar yield after enzymatic hydrolysis, achieved with pretreatment at 170 degrees C for 40 min, was 34.1 g per 100 g SFF, comprising 12.8 g glucose, 13.9 g xylose and 7.4 g arabinose, corresponding to 66%, 71% and 51% of the theoretical, respectively.     

Biogas production and saccharification of Salix pretreated at different steam explosion conditions

Different steam explosion conditions were applied to Salix chips and the effect of this pretreatment was evaluated by running both enzymatic hydrolysis and biogas tests. Total enzymatic release of glucose and xylose increased with pretreatment harshness, with maximum values being obtained after pretreatment for 10 min at 210 °C. Harsher pretreatment conditions did not increase glucose release, led to degradation of xylose and to formation of furfurals. Samples pretreated at 220 and 230 °C initially showed low production of biogas, probably because of inhibitors produced during the pretreatment, but the microbial community was able to adapt and showed high final biogas production. Interestingly, final biogas yields correlated well with sugar yields after enzymatic hydrolysis, suggesting that at least in some cases a 24 h enzymatic assay may be developed as a quick method to predict the effects of pretreatment of lignocellulosic biomass on biogas yields.