Solid‐state synthesis and luminescent properties of yellow‐emitting phosphor NaY(MoO4)2:Dy3+ for white light‐emitting diodes

A yellow‐emitting phosphor NaY(MoO₄)₂:Dy³⁺ was synthesized using a solid‐state reaction at 550 °C for 4 h, and its luminescent properties were investigated. Its phase formation was studied using X‐ray powder diffraction analysis, and there were no crystalline phases other than NaY(MoO₄)₂. NaY(MoO₄)₂:Dy³⁺ produced yellow emission under 386 or 453 nm excitation, and the prominent luminescence was yellow (575 nm) due to the ⁴ F_9/2→⁶H_13/2 transition of Dy³⁺. For the 575 nm emission, the excitation spectrum had one broad band and some narrow peaks; the peaks were located at 290, 351, 365, 386, 426, 453 and 474 nm. Emission intensities were influenced by the Dy³⁺ doping content and a concentration quenching effect was observed; the phenomenon was also proved by the decay curves. Moreover, the Commission International de I'Eclairage chromaticity coordinates of NaY(MoO₄)₂:Dy³⁺ showed similar values at different Dy³⁺ concentrations, and were located in the yellow region. Copyright © 2015 John Wiley & Sons, Ltd.     

Energy transfer in M5(PO4)3 F:Eu2+,Ce3+ (M = Ca and Ba) phosphors

M₅(PO₄)₃ F:Eu²⁺ (M = Ca and Ba) co‐doped with Ce³⁺ phosphors were successfully prepared by the combustion synthesis method. The introduction of co‐dopant (Ce³⁺) into the host enhanced the luminescent intensity of the M₅(PO₄)₃ F:Eu²⁺ (M = Ca and Ba) efficiently. Previously, we have reported the synthesis and photoluminescence properties of same phosphors. The aim of this article is to report energy transfer mechanism between Ce³⁺?Eu²⁺ ions in M₅(PO₄)₃ F:Eu²⁺ (M = Ca and Ba) phosphors, where Ce³⁺ ions act as sensitizers and Eu²⁺ ions act as activators. The M₅(PO₄)₃ F:Eu²⁺ (M = Ca and Ba) co‐doped with Ce³⁺ phosphor exhibits great potential for use in white ultraviolet (UV) light‐emitting diode applications to serve as a single‐phased phosphor that can be pumped with near‐UV or UV light‐emitting diodes. Copyright © 2013 John Wiley & Sons, Ltd.     

Photoluminescence,cathodoluminescence and thermal stability of Sm3+‐activated Sr3La(VO4)3 red‐emitting phosphors

A series of Sm³⁺‐activated Sr₃La(VO₄)₃ phosphors were synthesized by a facile sol‐gel method. X‐ray diffraction patterns and photoluminescence (PL)/cathodoluminescence (CL) spectra as well as PL decay curves were employed to characterize the obtained samples. Upon 402 nm light excitation, the characteristic emissions of Sm³⁺ ions corresponding to ⁴G_5/2→⁶H_J transitions were observed in all the as‐prepared products. The PL emission intensity was increased with increase in Sm³⁺ ion concentration, while concentration quenching occurred when the doping concentration was over 4 mol%. The non‐radiative energy transfer mechanism for concentration quenching of Sm³⁺ ions was dominated by dipole–dipole interaction and the critical distance was around 21.59 Å. Furthermore, temperature‐dependent PL emission spectra revealed that the obtained phosphors possessed good thermal stability with an activation energy of 0.19 eV. In addition, the CL spectra of the samples were almost the same as the PL spectra, and the CL emission intensity showed a tendency to increase with increase in accelerating voltage and filament current. These results suggest that the Sm³⁺‐activated Sr₃La(VO₄)₃ phosphors with good color coordinates, high color purity and superior thermal stability may be a potential candidate for applications in white light‐emitting diodes and field‐emission displays as red‐emitting phosphors.     

Synthesis and photoluminescence characteristics of Sm3+‐doped Bi4Si3O12 red‐emitting phosphor

A series of novel red‐emitting Sm³⁺‐doped bismuth silicate phosphors, Bi₄Si₃O₁₂:xSm³⁺ (0.01 ≤ x ≤ 0.06), were prepared via the sol–gel route. The phase of the synthesized samples calcinated at 800 °C is isostructural with Bi₄Si₃O₁₂ according to X‐ray diffraction results. Under excitation with 405 nm light, some typical peaks of Sm³⁺ ions centered at 566, 609, 655 and 715 nm are found in the emission spectra of the Sm³⁺‐doped Bi₄Si₃O₁₂ phosphors. The strongest peak located at 609 nm is due to ⁴G_5/2–⁶H_7/2 transition of Sm³⁺. The luminescence intensity reaches its maximum value when the Sm³⁺ ion content is 4 mol%. The results suggest that Bi₄Si₃O₁₂:Sm³⁺ may be a potential red phosphor for white light‐emitting diodes. Copyright © 2016 John Wiley & Sons, Ltd.     

A novel reddish‐orange phosphor,NaLi2PO4:Eu3+

A series of Eu³⁺‐activated NaLi₂PO₄ novel phosphors was synthesized by the solid‐state reaction method. The X‐ray diffraction (XRD) and photoluminescence (PL) properties of these phosphors were investigated at room temperature. The excitation spectra indicate that these phosphors can be effectively excited by near‐UV (370–410 nm) light. The emission spectra exhibit strong reddish‐orange performance, which is due to the ⁵D₀ → ⁷F_J transitions of Eu³⁺ ions. The orange emission from transition ⁵D₀ → ⁷F₁ is dominant over that of ⁵D₀ → ⁷F_2. The concentration quenching of Eu³⁺ was observed in NaLi₂PO₄:Eu³⁺ when the Eu concentration was at 1 mol%. The impact of doping Eu³⁺ and photoluminescence properties were investigated and we propose a feasible interpretation. Copyright © 2012 John Wiley & Sons, Ltd.     

Synthesis and luminescence properties of cubic‐shaped Ca1‐xTiO3:Eu3+ particles

In this article Ca_1‐xTiO₃:xEu³⁺ single crystalline particles with a cubic morphology and average size of 248 to 815 nm were synthesized by a solvothermal method. The structural and optical properties of the Ca_1‐xTiO₃:xEu³⁺ cubes were investigated, the formation mechanism of the cubes were analyzed and discussed, and the influence of Eu doping content and cubic size on the photoluminescence were examined. The differences in the photoluminescence between Ca_1‐xTiO₃:xEu³⁺ cubic crystals and nanoparticles was analyzed. It was found that an addition of a small amount of water can substantially reduce the size of the cubes. An obvious red emission band centered at 615 nm was observed under the excitation at 395 nm for the cubes. Our results demonstrate CaTiO₃ cubes are good host materials for designing red phosphors.     

Size‐tailored synthesis and luminescent properties of three‐dimensional BaMoO4, BaMoO4:Eu3+ micron‐octahedrons and micron‐flowers via sonochemical route

Almost monodisperse three‐dimensional (3D) BaMoO_4, BaMoO₄:Eu³⁺ micron‐octahedrons and micron‐flowers were successfully prepared via a large‐scale and facile sonochemical route without using any catalysts or templates. X‐Ray diffraction (XRD), field emission scanning electron microscopy (FE‐SEM), energy dispersion X‐ray (EDS), Fourier transform infrared (FTIR) and photoluminescence (PL) spectroscopy were employed to characterize the as‐obtained products. It was found that size modulation could be easily realized by changing the concentrations of reactants and the pH value of precursors. The formation mechanism for micron‐octahedrons and micron‐flowers was proposed on the basis of time‐dependent experiments. Using excitation wavelengths of 396 or 466 nm for BaMoO₄:Eu³⁺ phosphors, an intense emission line at 614 nm was observed. These phosphors might be promising components with possible application in the fields of near UV‐ and blue‐excited white light‐emitting diodes. Simultaneously, this novel and efficient pathway could open new opportunities for further investigating the properties of molybdate materials. Copyright © 2014 John Wiley & Sons, Ltd.     

Luminescent properties of sol–gel processed red‐emitting phosphor Ca0.6Sr0.4–1.5x‐0.5yMo0.4 W0.6O4:EuxLiy

A series of red‐emitting phosphors Ca_0.6Sr_{0.4–1.5x‐0.5y}Mo_0.4 W_0.6O₄:Eu_xLi_y (x = 0.02–0.12, y = 0–0.12) has been synthesized by a sol‐gel method. The effects of calcining temperature, concentrations of Li⁺ and Eu³⁺, and compensation ions on the luminescent properties were investigated. X‐ray diffraction and scanning electron microscopic results showed that as‐prepared phosphors were of single phase with several microns. The Li⁺ compensated compositions showed remarkably intense red emission at 619 nm. The emission intensity of the series reached maximum for compositions at x = 0.08 and y = 0.08 when the calcining temperature was 900 °C. Copyright © 2014 John Wiley & Sons, Ltd.     

A promising RVO4:Eu3+,Li+@SiO2 (R = Gd,Y and Gd/Y) red‐emitting phosphor with improved luminescence (cd/m2) and colour purity for optical display applications

Red emission intensity was optimized in three stages, by investigating the effects of: (i) host composition (Gd, Y and Gd/Y), (ii) codoping Li⁺ as a sensitizer and, finally, (iii) with a SiO₂ shell coating as a protecting layer. Lanthanide vanadate powder phosphors were synthesized using a modified colloidal precipitation technique. The effects of SiO₂ coating on phosphor particles were characterized using scanning electron microscopy (SEM)‐EDAX, transmission electron microscopy (TEM), Fourier transform infrared (FTIR) and photoluminescence (PL) measurements. An improvement in the PL intensity on Li codoping was due to improved crystallinity, which led to higher oscillating strengths for the optical transitions, and also a lowering of the inversion symmetry of Eu³⁺ ions. Red emission intensity due to ⁵D₀ → ⁵D₂ transition of the phosphor Y_0.94VO₄:Eu³⁺_0.05,Li⁺_0.01 was enhanced by 22.28% compared with Y_0.95VO₄:Eu³⁺_0.05, and was further improved by 58.73% with SiO₂ coating. The luminescence intensity (I) and colour coordinates (x, y) of the optimized phosphor Y_0.94VO₄:Eu³⁺_0.05,Li⁺_0.01@SiO₂, where I = 13.07 cd/m² and (x = 0.6721, y = 0.3240), were compared with values for a commercial red phosphor (Y₂O₂S:Eu³⁺), where I = 27 cd/m² and (x = 0.6522, y = 0.3437). The measured colour coordinates are superior to those of the commercial red phosphor, and moreover, match well with standard NTSC values (x = 0.67, y = 0.33). Copyright © 2015 John Wiley & Sons, Ltd.     

Orange light‐emitting Ca3Mg3(PO4)4:Sm3+ phosphors

This work reports the photoluminescence properties of Ca₃Mg₃(PO₄)₄:Sm³⁺ phosphors that were synthesized by the combustion method. The phase formation and morphology of the prepared phosphors were analysed by X‐ray diffraction studies and scanning electron microscopy. Ca₃Mg₃(PO₄)₄:Sm³⁺ phosphors give orange light emission when excited by near‐ultraviolet (NUV) and blue light. The photoluminescence characteristics of the as‐prepared phosphors were investigated and their emission spectra showed three peaks due to ⁴G_5/2 → ⁶H_5/2, ⁴G_5/2 → ⁶H_7/2 and ⁴G_5/2 → ⁶H_9/2 transitions. The mechanism responsible for the concentration quenching of luminescence was found to be an electric dipole–dipole interaction. The CIE chromaticity coordinates suggested that the prepared phosphors are potential candidates for orange light‐emitting diodes (LEDs).     

Sol–gel preparation and luminescent properties of red‐emitting phosphor Sr‐Ba‐Mo‐W‐O‐(Eu3+,Sm3+)

Two series of red‐emitting phosphors Sr‐Ba‐Mo‐W‐O:Eu,Sm and Sr‐Ba‐Mo‐W‐O:Eu have been synthesized by a sol–gel method. The effects of the chemical composition, concentrations of Sm³⁺ and Eu³⁺, the Sr²⁺/Ba²⁺ ratio, and the W⁶⁺/Mo⁶⁺ ratio on the luminescent properties were investigated. The as‐prepared phosphors were characterized by X‐ray diffraction and Raman spectra. Results showed that single phases of the two series were prepared. The compositions of Sr_0.6Ba_0.13Mo_0.8 W_0.2O₄:Eu_0.10Sm_0.08 and Sr_0.75Ba_0.1Mo_0.8 W_0.2O₄:Eu_0.10 had the strongest luminescent intensity. The excitation spectra of Sm³⁺, Eu³⁺ co‐doped phosphors were broader and the strongest peak moved to 404 nm when compared with that of Eu³⁺ single‐doped phosphors. The luminescent intensity of the Sr_0.6Ba_0.13Mo_0.8 W_0.2O₄:Eu_0.10Sm_0.08 at 618 nm were 2.8 times greater than that of Sr_0.75Ba_0.1Mo_0.8 W_0.2O₄:Eu_0.10. The luminescent intensity of Sr_0.6Ba_0.13Mo_0.8 W_0.2O₄:Eu_0.10Sm_0.08 and Sr_0.75Ba_0.1Mo_0.8 W_0.2O₄:Eu_0.10 at 150 °C decreased to 56.8% and 50.3% of the initial value at room temperature, respectively. Copyright © 2015 John Wiley & Sons, Ltd.     

Thermal quenching of luminescence of LiSr4(BO3)3:Eu2+ orange‐emitting phosphor

An orange‐emitting phosphor, Eu²⁺‐activated LiSr₄(BO₃)₃, was synthesized using the conventional solid‐state reaction. The photoluminescence excitation and emission spectra, and temperature dependence of the luminescence intensity of the phosphor were investigated. The results showed that LiSr₄(BO₃)₃:Eu²⁺ could be efficiently excited by incident light of 250–450 nm, and emits a strong orange light. With increasing temperature, the emission bands of LiSr₄(BO₃)₃:Eu²⁺ show an abnormal blue‐shift with broadening bandwidth and decreasing emission intensity. Copyright © 2013 John Wiley & Sons, Ltd.     

Luminescence enhancement of (Sr1–xMx)2SiO4:Eu2+ phosphors with M (Ca2+/Zn2+) partial substitution for white light‐emitting diodes

Eu²⁺‐doped Sr₂SiO₄ phosphor with Ca²⁺/Zn²⁺ substitution, (Sr_1–xM_x)₂SiO₄:Eu²⁺ (M = Ca, Zn), was prepared using a high‐temperature solid‐state reaction method. The structure and luminescence properties of Ca²⁺/Zn²⁺ partially substituted Sr₂SiO₄:Eu²⁺ phosphors were investigated in detail. With Ca²⁺ or Zn²⁺ added to the silicate host, the crystal phase could be transformed between the α‐form and the β‐form of the Sr₂SiO₄ structure. Under UV excitation at 367 nm, all samples exhibit a broad band emission from 420 to 680 nm due to the 4f⁶5d¹ → 4f⁷ transition of Eu²⁺ ions. The broad emission band consists of two peaks at 482 and 547 nm, which correspond to Eu²⁺ ions occupying the ten‐fold oxygen‐coordinated Sr.(I) site and the nine‐fold oxygen‐coordinated Sr.(II) site, respectively. The luminescence properties, including the intensity and lifetime of Sr₂SiO₄:Eu²⁺ phosphors, improved remarkably on Ca²⁺/Zn²⁺ addition, and promote its application in white light‐emitting diodes. Copyright © 2016 John Wiley & Sons, Ltd.     

Eu3+-activated red phosphor Ca3YAl3B4O15 with low thermal quenching behaviour

This paper reports a sequence of a Ca₃YAl₃B₄O₁₅:xEu³⁺ red phosphor prepared using a high-temperature solid-state reaction. At the excitation of 396 nm, the samples emitted intense red emission centred at ~623 nm, which could be attributed to the ⁵D₀→⁷F₂ transition of the Eu³⁺ ion. The results showed that the optimum Eu³⁺ doping concentration of Ca₃YAl₃B₄O₁₅:Eu³⁺ phosphor was x = 80 mol%, and the concentration quenching mechanism of Ca₃YAl₃B₄O₁₅:Eu³⁺ red phosphor belonged to the exchange coupling between Eu³⁺ ions. The Commission Internationale de l'éclairage (CIE) coordinates and colour purity of Ca₃Y_0.2Al₃B₄O₁₅:0.8Eu³⁺ were calculated as (0.6375, 0.3476) and 95.5%, respectively. Moreover, the red emission of the obtained phosphor Ca₃YAl₃B₄O₁₅:0.8Eu³⁺ exhibited a low thermal quenching behaviour with an intensity retention rate of 92.85% at 150°C. The above results manifest that the Eu³⁺-activated Ca₃YAl₃B₄O₁₅ phosphor is predicted to be a promising red luminescent component for white light-emitting diodes.     

Enhanced red emission from BaMoO4: Eu3+ by Bi3+ co‐doping

A series of Bi³⁺,Eu³⁺‐doped BaMoO₄ phosphors was synthesized using a hydrothermal method. The crystal structure, morphology and optical properties of the phosphors were studied using X‐ray diffraction (XRD), scanning electron microscope (SEM) and photoluminescence (PL) measurements. Three different particle morphologies were detected in the SEM observation. The energy dispersive spectroscopy (EDS) results indicated that the solubility of Bi³⁺ in spherical or rugby‐like BaMoO₄ particles was very low and the excess Bi³⁺ element was cumulated in the irregular particles. Characteristic emissions of Eu³⁺ ions (⁵D₀ → ⁷F_J; J = 0, 1, 2, 3, 4) were observed under excitation in ultraviolet (UV) light, with the most intense transition being the ⁵D₀ → ⁷F₂ transition. Energy transfer from MoO₄^2? and Bi³⁺ to Eu³⁺ can be readily achieved. Red emission intensity of Eu³⁺ was enhanced by a factor of two by co‐doping with a small amount of Bi³⁺. Optical properties as a function of Bi³⁺ content were studied and the optimum Bi³⁺ content in BaMoO₄ nanocrystals was determined to be 0.4 mol%.     

A novel red phosphor Ca2YNbO6:Eu3+ for WLEDs

Due to the advantages of good physicochemical properties, thermal stability, and optical properties, double perovskite compounds have received extensive attention. On this basis, a new type of red phosphor, Ca₂YNbO₆:xEu³⁺, was synthesized using a high-temperature solid-phase method. Its phase purity, morphology, elemental composition, absorption spectrum, photoluminescence, thermal stability, and Commission Internationale de l'éclairage (CIE) chromaticity coordinates were thoroughly investigated. The results display that there is no impurity phase in the samples and the convergence factor R_wp = 14.2%; the microscopic particles are uniform and full, and the distribution of each element is uniform. The energy band gap ΔE is between 3.71 eV and 3.65 eV. The luminescence intensity is the best when the doped Eu³⁺ concentration x reaches 0.4, and emits 612 nm red light (⁵D₀→⁷F₂) under 465 nm excitation, and the concentration quenching is attributed to a d–d interaction. The luminescence intensity at 425 K was still 75% of the room temperature luminescence intensity, which indicates that the thermal stability is extremely superior. The CIE chromaticity coordinates (0.6534, 0.3455) of the Ca2YNbO6:0.4Eu³⁺ phosphors are very close to National Television Standards Committee (0.670, 0.330), and the samples have low correlated colour temperature (2656 K) and high colour purity (99.90%). All findings suggest that Ca₂YNbO₆:Eu³⁺ can serve as a substitute for red phosphor in WLEDs.     

Enhanced orange–red emission of SrZn2(PO4)2:Sm3+ via codoping Eu2+ as a sensitizer

A series of Eu²⁺‐, Sm³⁺‐ and Eu²⁺/Sm³⁺‐doped SrZn₂(PO₄)₂ samples were synthesized using a solid‐state reaction. SrZn₂(PO₄)₂:Eu²⁺ presented a broad emission band due to 4f⁶5d–4f⁷ transition of the Eu²⁺ ion. The spectra of SrZn₂(PO₄)₂:Sm sintered in air and H₂/N₂ were identical in every aspect, except for a very small difference in intensity. A Eu²⁺–Sm³⁺ energy transfer scheme was proposed to realize the sensitization of Sm³⁺ ion emission by Eu²⁺ ions, and UV‐convertible Sm³⁺‐activated red phosphor was obtained in SrZn₂(PO₄)₂:Eu²⁺, Sm³⁺. Copyright © 2015 John Wiley & Sons, Ltd.     

Sol‐gel synthesis and luminescent properties of red‐emitting Y(P,V)O4:Eu3+ phosphors

Eu³⁺‐activated Y(P,V)O₄ phosphors were prepared by the EDTA sol‐gel method, and the corresponding morphologies and luminescent properties were investigated. The sample particles were relatively spheroid with size of 2–3 µm and had a smooth surface. The excitation spectra for Y(P,V)O₄:Eu³⁺ consisted of three strong excitation bands in the 200–350 nm range, which were attributed to a Eu³⁺‐ O^2? charge‐transfer band and ¹A₁?¹ T₁/¹ T₂ transitions in VO₄^3?. The as‐synthesized phosphors exhibited a highly efficient red luminescence at 613 nm due to the Eu^{3+ 5}D₀?⁷ F₂ electric dipole transition. With the increase in the V⁵⁺/P⁵⁺ ratio, the luminescence intensity of the red phosphor under UV excitation was greatly improved due to enhanced VO₄^3? → Eu³⁺ energy transfer. Copyright © 2015 John Wiley & Sons, Ltd.     

Luminescence and energy‐transfer properties of color‐tunable Ca2Mg0.25Al1.5Si1.25O7:Ce3+/Eu2+/Tb3+ phosphors for ultraviolet light‐emitting diodes

A series of Ca₂Mg_0.25Al_1.5Si_1.25O₇:Ce³⁺/Eu²⁺/Tb³⁺ phosphors was been prepared via a conventional high temperature solid‐state reaction and their luminescence properties were studied. The emission spectra of Ca₂Mg_0.25Al_1.5Si_1.25O₇:Ce³⁺,Eu²⁺ and Ca₂Mg_0.25Al_1.5Si_1.25O₇:Ce³⁺,Tb³⁺ phosphors show not only a band due to Ce³⁺ ions (409 nm) but also as a band due to Eu²⁺ (520 nm) and Tb³⁺ (542 nm) ions. More importantly, the effective energy transfer from Ce³⁺ to Eu²⁺ and Tb³⁺ ions was confirmed and investigated by emission/excitation spectra and luminescent decay behaviors. Furthermore, the energy level scheme and energy transfer mechanism were investigated and were demonstrated to be of resonant type via dipole–dipole (Ce³⁺ to Eu²⁺) and dipole–quadrupole (Ce³⁺ to Tb³⁺) reactions, respectively. Under excitation at 350 nm, the emitting color could be changed from blue to green by adjusting the relative doping concentration of Ce³⁺ and Eu²⁺ ions as well as Ce³⁺ and Tb³⁺ ions. The above results indicate that Ca₂Mg_0.25Al_1.5Si_1.25O₇:Ce³⁺,Eu²⁺/Tb³⁺ are promising single‐phase blue‐to‐green phosphors for application in phosphor conversion white‐light‐emitting diodes. Copyright © 2015 John Wiley & Sons, Ltd.     

Luminescent properties of Ca3SiO4Cl2 co‐doped with Ce3+ and Eu2+ for near‐ultraviolet light‐emitting diodes

Ca₃SiO₄Cl₂ co‐doped with Ce³⁺,Eu²⁺ was prepared by high temperature reaction. The structure, luminescent properties and the energy transfer process of Ca₃SiO₄Cl₂: Ce³⁺,Eu²⁺ were investigated. Eu²⁺ ions can give enhanced green emission through Ce³⁺ → Eu²⁺ energy transfer in these phosphors. The green phosphor Ca_2.9775SiO₄Cl₂:0.0045Ce³⁺,0.018Eu²⁺ showed intense green emission with broader excitation in the near‐ultraviolet light range. A green light‐emitting diode (LED) based on this phosphor was made, and bright green light from this green LED could be observed by the naked eye under 20 mA current excitation. Hence it is considered to be a good candidate for the green component of a three‐band white LED. Copyright © 2015 John Wiley & Sons, Ltd.