Nitrogen‐doped carbon dots as a fluorescent probe for the highly sensitive detection of Ag+ and cell imaging

An easy hydrothermal synthesis strategy was applied to synthesize green‐yellow emitting nitrogen‐doped carbon dots (N‐CDs) using 1,2‐diaminobenzene as the carbon source, and dicyandiamide as the dopant. The nitrogen‐doped CDs resulted in improvement in the electronic characteristics and surface chemical activities. N‐CDs exhibited bright fluorescence emission and could response to Ag⁺ selectively and sensitively. Other ions produced nearly no interference. A N‐CDs based fluorescent probe was then applied to sensitively determine Ag⁺ with a detection limit of 5 × 10^?8 mol/L. The method was applied to the determination of Ag⁺ dissolved in water. Finally, negligibly cytotoxic, excellently biocompatibile, and highly fluorescent carbon dots were applied for HepG2 cell imaging and the quenched fluorescence by adding Ag⁺, which indicated its potential applications.     

Dramatic red fluorescence enhancement and emission red shift of carbon dots following Zn/ZnO decoration

Metal atom doping, an easy and convenient method, can optimize and tune the physical–chemical properties and photometrics of carbon dots (CDs). However, there are few reports on the preparation of metal‐decorated CDs that give red emission and a high photoluminescence quantum yield (PLQY). Here, we demonstrate a zinc (existing in human body) ion‐doping strategy to observably enhance the PLQY and lengthen the CD emission wavelength. The prepared Zn/ZnO‐decorated CDs (Zn‐CDs) produced red fluorescence (623 nm) with a superior PLQY of 40.3%. Through a series of analyses, Zn‐CDs were confirmed to contain an oxidation state and reduction state of Zn doping into the internal defects and surface of Zn‐CDs. More valuably, the Zn‐CDs had excellent chemical stability, photo‐stability, long‐term storage stability, and high biocompatibility, and therefore could be used as a robust red fluorescence probe for high‐quality cellular imaging.     

Superior Oxygen Reduction Reaction on Phosphorus‐Doped Carbon Dot/Graphene Aerogel for All‐Solid‐State Flexible Al–Air Batteries

Carbon dots have been recognized as one of the most promising candidates for the oxygen reduction reaction (ORR) in alkaline media. However, the desired ORR performance in metal–air batteries is often limited by the moderate electrocatalytic activity and the lack of a method to realize good dispersion. To address these issues, herein a biomass‐deriving method is reported to achieve the in situ phosphorus doping (P‐doping) of carbon dots and their simultaneous decoration onto graphene matrix. The resultant product, namely P‐doped carbon dot/graphene (P‐CD/G) nanocomposites, can reach an ultrahigh P‐doping level for carbon nanomaterials. The P‐CD/G nanocomposites are found to exhibit excellent ORR activity, which is highly comparable to the commercial Pt/C catalysts. When used as the cathode materials for a primary liquid Al–air battery, the device shows an impressive power density of 157.3 mW cm^?2 (comparing to 151.5 mW cm^?2 of a similar Pt/C battery). Finally, an all‐solid‐state flexible Al–air battery is designed and fabricated based on our new nanocomposites. The device exhibits a stable discharge voltage of ≈1.2 V upon different bending states. This study introduces a unique biomass‐derived material system to replace the noble metal catalysts for future portable and wearable electronic devices.     

Theoretical and experimental investigation of doping M in ZnSe (M = Cd,Mn, Ag,Cu) clusters: optical and bonding characteristics

The optical and bonding characteristics of doping ZnSe quantum dots (QDs) were investigated. Cd‐, Mn‐, Ag‐ and Cu‐doped ZnSe were synthesized in aqueous solution. Theoretically, the intensity of the Cd–Se bond was similar to that of the Zn–Se bond, which illustrates that Cd can be doped into ZnSe materials at any ratio. We found that Mn–Se bonding was stronger than Zn–Se bonding. Ag‐doped ZnSe nanoclusters show the same bonding and configuration as Cu‐doped ZnSe. Moreover, Cd can be doped into ZnSe using both the substitution‐ and vacancy‐doping method. For Mn‐doped ZnSe clusters, small amounts of Mn impurity lead to stronger bonding with Se, but larger amounts of Mn impurity led to the formation of a Mn–Mn metal bond. The theoretical results show that it is difficult to form a vacancy‐doping cluster for Mn‐doped ZnSe materials. In experiments, the absorption and photoluminescence (PL) spectral wavelengths of Mn‐doped ZnSe nanocrystals were the same as those of pure ZnSe nanocrystals, showing that the Mn impurity is not doped into ZnSe nanocrystals. Ag‐ and Cu‐doped ZnSe nanocrystals have the same PL characteristics. The doping of an impurity is related to the solubility product, and not the bonding intensity. Copyright © 2015 John Wiley & Sons, Ltd.     

Synthesis of highly fluorescent nitrogen and phosphorus doped carbon dots for the detection of Fe3+ ions in cancer cells

Highly fluorescent nitrogen and phosphorus‐doped carbon dots with a quantum yield 59% have been successfully synthesized from citric acid and di‐ammonium hydrogen phosphate by single step hydrothermal method. The synthesized carbon dots have high solubility as well as stability in aqueous medium. The as‐obtained carbon dots are well monodispersed with particle sizes 1.5–4 nm. Owing to a good tunable fluorescence property and biocompatibility, the carbon dots were applied for intercellular sensing of Fe³⁺ ions as well as cancer cell imaging. Copyright © 2015 John Wiley & Sons, Ltd.     

Ultrafine Metal Nanoparticles/N‐Doped Porous Carbon Hybrids Coated on Carbon Fibers as Flexible and Binder‐Free Water Splitting Catalysts

By employing in situ reduction of metal precursor and metal‐assisted carbon etching process, this study achieves a series of ultrafine transition metal‐based nanoparticles (Ni–Fe, Ni–Mo) embedded in N‐doped carbon, which are found efficient catalysts for electrolytic water splitting. The as‐prepared hybrid materials demonstrate outstanding catalytic activities as non‐noble metal electrodes rendered by the synergistic effect of bimetal elements and N‐dopants, the improved electrical conductivity, and hydrophilism. Ni/Mo₂C@N‐doped porous carbon (NiMo‐polyvinylpyrrolidone (PVP)) and NiFe@N‐doped carbon (NiFe‐PVP) produce low overpotentials of 130 and 297 mV at a current density of 10 mA cm^?2 as catalysts for hydrogen evolution reaction and oxygen evolution reaction, respectively. In addition, these binder‐free electrodes show long‐term stability. Overall water splitting is also demonstrated based on the couple of NiMo‐PVP||NiFe‐PVP catalyzer. This represents a simple and effective synthesis method toward a new type of nanometal–carbon hybrid electrodes.     

Sensitization enhancement of europium in ZnSe/ZnS core/shell quantum dots induced by efficient energy transfer

Eu‐doped ZnSe:/ZnS quantum dots (formed as ZnSe:Eu/ZnS QDs) were successfully synthesized by a two‐step wet chemical method: nucleation doping and epitaxial shell growing. The sensitization characteristics of Eu‐doped ZnSe and ZnSe/ZnS core/shell QD are studied in detail using photoluminescence (PL), PL excitation spectra (PLE) and time‐resolved PL spectroscopy. The emission intensity of Eu ions is enhanced and that of ZnSe QDs is decreased, implying that energy was transferred from the excited ZnSe host materials (the donor) to the doped Eu ions (the acceptor). PLE reveals that the ZnSe QDs act as an antenna for the sensitization of Eu ions through an energy transfer process. The dynamics of ZnSe:Eu/ZnS core/shell quantum dots with different shell thicknesses and doping concentrations are studied via PL spectra and fluorescence lifetime spectra. The maximum phosphorescence efficiency is obtained when the doping concentration of Eu is approximately 6% and the sample showed strong white light under ultraviolet lamp illumination. By surface modification with ZnS shell layer, the intensity of Eu‐related PL emission is increased approximately three times compared with that of pure ZnSe:Eu QDs. The emission intensity and wavelength of ZnSe:Eu/ZnS core/shell quantum dots can be modulated by different shell thickness and doping concentration. The results provide a valuable insight into the doping control for practical applications in laser, light‐emitting diodes and in the field of biotechnology. Copyright © 2014 John Wiley & Sons, Ltd.     

Heteroatom‐Doped and Oxygen‐Functionalized Nanocarbons for High‐Performance Supercapacitors

Electrochemical capacitors (best known as supercapacitors) are high‐performance energy storage devices featuring higher capacity than conventional capacitors and higher power densities than batteries, and are among the key enabling technologies of the clean energy future. This review focuses on performance enhancement of carbon‐based supercapacitors by doping other elements (heteroatoms) into the nanostructured carbon electrodes. The nanocarbon materials currently exist in all dimensionalities (from 0D quantum dots to 3D bulk materials) and show good stability and other properties in diverse electrode architectures. However, relatively low energy density and high manufacturing cost impede widespread commercial applications of nanocarbon‐based supercapacitors. Heteroatom doping into the carbon matrix is one of the most promising and versatile ways to enhance the device performance, yet the mechanisms of the doping effects still remain poorly understood. Here the effects of heteroatom doping by boron, nitrogen, sulfur, phosphorus, fluorine, chlorine, silicon, and functionalizing with oxygen on the elemental composition, structure, property, and performance relationships of nanocarbon electrodes are critically examined. The limitations of doping approaches are further discussed and guidelines for reporting the performance of heteroatom doped nanocarbon electrode‐based electrochemical capacitors are proposed. The current challenges and promising future directions for clean energy applications are discussed as well.     

Cu‐doped quantum dots: a new class of near‐infrared emitting fluorophores for bioanalysis and bioimaging

Transition metal ion‐doped quantum dots (QDs) exhibit unique optical and photophysical properties that offer significant advantages over undoped QDs, such as larger Stokes shift to avoid self‐absorption/energy transfer, longer excited‐state lifetimes, wider spectral window, and improved chemical and thermal stability. Among the doped QDs emitters, Cu is widely introduced into the doped QDs as novel, efficient, stable, and tunable optical materials that span a wide spectrum from blue to near‐infrared (NIR) light. Their unique physical and chemical characteristics enable the use of Cu‐doped QDs as NIR labels for bioanalysis and bioimaging. In this review, we discuss doping mechanisms and optical properties of Cu‐doped QDs that are capable of NIR emission. Applications of Cu‐doped QDs in in vitro biosensing and in in vivo bioimaging are highlighted. Moreover, a prospect of the future of Cu‐doped QDs for bioanalysis and bioimaging are also summarized.     

Aqueous synthesis of highly luminescent surface Mn2+‐doped CdTe quantum dots as a potential multimodal agent

Mn²⁺‐doped CdTe quantum dots (QDs) were synthesized directly via a facile surface doping strategy in aqueous solution. The best optical property emerged when the added amount of Mn²⁺ was 5% compared to Cd²⁺ in the CdTe nanoparticles and the reaction temperature was 60 °C. The fluorescence and magnetic properties of the QDs were studied. The as‐prepared Mn²⁺‐doped CdTe QDs have high quantum yield (48.13%) and a narrow distribution with an average diameter of 3.7 nm. The utility of biological imaging was also studied. Depending on the high quantum yield, cells in culture were illuminated and made more distinct from each other compared to results obtained with normal QDs. They also have a prominent longitudinal relaxivity value (r₁ = 4.2 mM^?1s^?1), which could indicate that the Mn²⁺‐doped CdTe QDs can be used as a potential multimodal agent for fluorescence and magnetic resonance imaging. Copyright © 2014 John Wiley & Sons, Ltd.     

Highly Active and Stable Graphene Tubes Decorated with FeCoNi Alloy Nanoparticles via a Template‐Free Graphitization for Bifunctional Oxygen Reduction and Evolution

Development of highly active and stable bifunctional oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) catalysts from earth‐abundant elements remains a grand challenge for highly demanded reversible fuel cells and metal–air batteries. Carbon catalysts have many advantages over others due to their low cost, excellent electrical conductivity, high surface area, and easy functionalization. However, they typically cannot withstand the highly oxidative OER environment. Here, a new class of bifunctional electrocatalyst is reported, consisting of ultralarge sized nitrogen doped graphene tubes (N‐GTs) (>500 nm) decorated with FeCoNi alloy particles. These tubes are prepared from an inexpensive precursor, dicyandiamide, via a template‐free graphitization process. The ORR/OER activity and the stability of these graphene tube catalysts depend strongly on the transition metal precursors. The best performing FeCoNi‐derived N‐GT catalyst exhibits excellent ORR and OER activity along with adequate electrochemical durability over a wide potential window (0–1.9 V) in alkaline media. The measured OER current is solely due to desirable O₂ evolution, rather than carbon oxidation. Extensive electrochemical and physical characterization indicated that high graphitization degree, thicker tube walls, proper nitrogen doping, and presence of FeCoNi alloy particles are vital for high bifunctional activity and electrochemical durability of tubular carbon catalysts.     

Metal‐Free Artificial Photosynthesis of Carbon Monoxide Using N‐Doped ZnTe Nanorod Photocathode Decorated with N‐Doped Carbon Electrocatalyst Layer

An artificial photosynthesis system based on N‐doped ZnTe nanorods decorated with an N‐doped carbon electrocatalyst layer is fabricated via an all‐solution process for the selective conversion of CO₂ to CO. Substitutional N‐doping into the ZnTe lattice decreases the bandgap slightly and improves the charge transfer characteristics, leading to enhanced photoelectrochemical activity. Remarkable N‐doping effects are also demonstrated by the N‐doped carbon layer that promotes selective CO₂‐to‐CO conversion instead of undesired water‐to‐H₂ reduction by providing active sites for CO₂ adsorption and activation, even in the absence of metallic redox centers. The photocathode shows promising performance in photocurrent generation (?1.21 mA cm^?2 at ?0.11 V_RHE), CO selectivity (dominant CO production of ≈72%), minor H₂ reduction (≈20%), and stability (corrosion suppression). The metal‐free electrocatalyst/photocatalyst combination prepared via a cost‐effective solution process exhibits high performance due to synergistic effects between them, and thus may find application in practical solar fuel production.     

Carbon dots as a luminescence sensor for ultrasensitive detection of phosphate and their bioimaging properties

Highly blue fluorescence carbon dots were synthesized by one‐step hydrothermal treatment of potatoes. The as‐obtained C‐dots have been applied to bioimaging of HeLa cells, which shows their excellent biocompatibility and low cytotoxicity. The results reveal that C‐dots are promising for real cell imaging applications. In addition, the carbon dots can be utilized as a probe for sensing phosphate. Copyright © 2014 John Wiley & Sons, Ltd.     

Uniform Lithium Deposition Assisted by Single‐Atom Doping toward High‐Performance Lithium Metal Anodes

For a long time lithium (Li) metal has been considered one of the most promising anodes for next‐generation rechargeable batteries. Despite decades of concentrated research, its practical application is still hindered by dendritic Li deposition and infinite volume change of Li metal anodes. Here, atomically dispersed metals doped graphene is synthesized to regulate Li metal nucleation and guide Li metal deposition. The single‐atom (SA) metals, supported on the nitrogen‐doped graphene can not only increase the Li adsorption energy of the localized area around the metal atomic sites with a moderate adsorption energy gradient but also improve the atomic structural stability of the overall materials by constructing a coordination mode of M‐N_x‐C (M, N, and C denoted as metal, nitrogen, and carbon atoms, respectively). As a result, the as‐obtained electrode exhibits an ultralow voltage hysteresis of 19 mV, a high average Coulombic efficiency of 98.45% over 250 cycles, and a stable Li plating/stripping performance even at a high current density of 4.0 mA cm^?2. This work demonstrates the application of SA metal doping in the rational design of Li metal anodes and provides a new concept for further development of Li metal batteries.     

Bifunctional Electrocatalytic Activity of Boron‐Doped Graphene Derived from Boron Carbide

A single material that can perform water oxidation and oxygen reduction reactions (ORR), also called bifunctional catalyst, represents a novel concept that emerged from recent materials research and that has led to applications in new‐generation energy‐storage systems, such as regenerative fuel cells. Here, metal/metal‐oxide free, doped graphene derived from rhombohedral boron carbide (B₄C) is demonstrated to be an effective bifunctional catalyst for the first time. B₄C, one of the hardest materials in nature next to diamond and cubic boron nitride, is converted and separated in bulk to form heteroatom (boron, B) doped graphene (BG, yield ≈7% by weight, after the first cycle). This structural conversion of B₄C to graphene is accompanied by in situ boron doping and results in the formation of an electrochemically active material from a non‐electrochemically active material, broadening its potential for application in various energy‐related technologies. The electrocatalytic efficacy of BG is studied using various voltammetric techniques. The results show a four‐electron transfer mechanism as well as a high methanol tolerance and stability towards ORR. The results are comparable to those from commercial 20 wt% Pt/C in terms of performance. Furthermore, the bifunctionality of the BG is also demonstrated by its performance in water oxidation.     

Metal–Organophosphine Framework‐Derived N,P‐Codoped Carbon‐Confined Cu3P Nanopaticles for Superb Na‐Ion Storage

Metal–organic framework derived approaches are emerging as a viable way to design carbon‐confined transitional metal phosphides (TMPs@C) for energy storage and conversion. However, their preparation generally involves a phosphorization using a large amount of additional P sources, which inevitably releases flammable, poisonous PH₃. Therefore, developing an efficient strategy for eco‐friendly synthesis of TMPs@C is full of challenges. Here, a metal–organophosphine framework (MOPF) derived strategy is developed to allow an eco‐friendly design of TMPs@C without an additional P source, avoiding release of PH₃. To illustrate this strategy, 1,3,5‐triaza‐7‐phosphaadamantane (PTA) ligands and Cu(NO₃)₂ metal centers are employed to construct Cu/PTA‐MOPFs nanosheets. Cu/PTA‐MOPFs can be directly converted to carbon‐confined Cu₃P nanoparticles by annealing. Benefiting from high heteroatom content in PTA, a high doping content of 3.92 at% N and 8.26 at% P can also be achieved in the carbon matrix. As a proof‐of‐concept application, N,P‐codoped carbon‐confined Cu₃P nanoparticles as anodes for Na‐ion storage exhibit a high initial reversible capacity of 332 mA h g^?1 at 50 mA g^?1, and superb rate and cyclic performance. Due to rich coordination modes of organophosphine, MOPFs are expected to become a promising molecular platform for design of various heteroatom‐doped TMPs@C for energy storage and conversion.     

One‐pot synthesis of fluorescent nitrogen‐doped carbon dots with good biocompatibility for cell labeling

Here we report an easy and economical hydrothermal carbonization approach to synthesize the fluorescent nitrogen‐doped carbon dots (N‐CDs) that was developed using citric acid and triethanolamine as the precursors. The synthesis conditions were optimized to obtain the N‐CDs with superior fluorescence performances. The as‐prepared N‐CDs are monodispersed sphere nanoparticles with good water solubility, and exhibited strong fluorescence, favourable photostability and excitation wavelength‐dependent behavior. Furthermore, the in vitro cytotoxicity and cellular labeling of N‐CDs were investigated using the rat glomerular mesangial cells. The results showed the N‐CDs have more inconspicuous cytotoxicity and better biosafety in comparison with ZnSe quantum dots, although both targeted the cells successfully. Considering their admirable photostability, low toxicity and good compatibility, the as‐obtained N‐CDs could have potential applications in biosensors, cellular imaging, and other fields.     

A Large Scalable and Low‐Cost Sulfur/Nitrogen Dual‐Doped Hard Carbon as the Negative Electrode Material for High‐Performance Potassium‐Ion Batteries

Among the negative electrode materials for potassium ion batteries, carbon is very promising because of its low cost and environmental benignity. However, the relatively low storage capacity and sluggish kinetics still hinder its practical application. Herein, a large scalable sulfur/nitrogen dual‐doped hard carbon is prepared via a facile pyrolysis process with low‐cost sulfur and polyacrylonitrile as precursors. The dual‐doped hard carbon exhibits hierarchical structure, abundant defects, and functional groups. The material delivers a high reversible potassium storage capacity and excellent rate performance. In particular, a high reversible capacity of 213.7 and 144.9 mA h g^?1 can be retained over 500 cycles at 0.1 A g^?1 and 1200 cycles at 3 A g^?1, respectively, demonstrating remarkable cycle stability at both low and high rates, superior to the other carbon materials reported for potassium storage, to the best of the authors' knowledge. Structure and kinetics studies suggest that the dual‐doping enhances the potassium diffusion and storage, profiting from the formation of a hierarchical structure, introduction of defects, and generation of increased graphitic and pyridinic N sites. This study demonstrates that a facile and scalable pyrolysis strategy is effective to realize hierarchical structure design and heteroatom doping of carbon, to achieve excellent potassium storage performance.     

Nitrogen‐Doped Porous Molybdenum Carbide and Phosphide Hybrids on a Carbon Matrix as Highly Effective Electrocatalysts for the Hydrogen Evolution Reaction

The efficient evolution of hydrogen through electrocatalysis is considered a promising approach to the production of clean hydrogen fuel. Platinum (Pt)‐based materials are regarded as the most active hydrogen evolution reaction (HER) catalysts. However, the low abundance and high cost of Pt hinders the large‐scale application of these catalysts. Active, inexpensive, and earth‐abundant electrocatalysts to replace Pt‐based materials would be highly beneficial to the production of cost‐effective hydrogen energy. Herein, a novel organoimido‐derivatized heteropolyoxometalate, Mo4‐CNP, is designed as a precursor for electrocatalysts of the HER. It is demonstrated that the carbon, nitrogen, and phosphorus sources derived from the Mo4‐CNP molecules lead to in situ confined carburization, phosphorization, and chemical doping on an atomic scale, thus forming nitrogen‐doped porous molybdenum carbide and phosphide hybrids, which exhibit remarkable electrocatalytic activity for the HER. Such an organically functionalized polyoxometalate‐assisted strategy described here provides a new perspective for the development of highly active non‐noble metal electrocatalysts for hydrogen evolution.     

Enantioselective cytotoxicity of ZnS:Mn quantum dots in A549 cells

Chirality strongly influences many biological properties of materials, such as cell accumulation, enzymatic activity, and toxicity. In the past decade, it has been shown that quantum dots (QDs), fluorescent semiconductor nanoparticles with unique optical properties, can demonstrate optical activity due to chiral ligands bound on their surface. Optically active QDs could find potential applications in biomedical research, therapy, and diagnostics. Consequently, it is very important to investigate the interaction of QDs capped with chiral ligands with living cells. The aim of our study was to investigate the influence of the induced chirality of Mn‐doped ZnS QDs on the viability of A549 cells. These QDs were stabilized with D‐ and L‐cysteine using a ligand exchange technique. The optical properties of QDs were studied using UV–Vis, photoluminescence (PL), and circular dichroism (CD) spectroscopy. The cytotoxicity of QDs was investigated by high content screening analysis. It was found that QDs stabilized by opposite ligand enantiomers, had identical PL and UV–Vis spectra and mirror‐imaged CD spectra, but displayed different cytotoxicity: QDs capped with D‐cysteine had greater cytotoxicity than L‐cysteine capped QDs.