Thermoluminescence properties of annealed natural quartz after beta irradiation

Here we investigated the effects of annealing, heating rate and fading (after annealing at 800 °C) on the thermoluminescence (TL) glow curves of natural quartz (NQ). All of the samples were annealed at different temperatures between 100 °C and 800 °C and then irradiated with a beta dose of about 34 Gray (Gy), in order to determine the effects of annealing treatments on TL peaks of natural quartz. TL glow curves of the samples were recorded. It was observed that the intensities of TL peaks were strongly sensitive to annealing temperatures at 800 °C. The heating rate and fading effect of TL peaks of natural quartz were examined for the annealed samples at 800 °C for 30 min. It was observed that the intensities of the TL peaks were differently affected from heating rate and fading. Additionally, TL kinetic parameters (activation energy, frequency factor and order of kinetics) of all peaks were determined for annealed samples using a computerized glow curve deconvolution (CGCD) method and Mathematica software. Copyright © 2016 John Wiley & Sons, Ltd.     

Thermoluminescence characterization of Ag‐doped Li2B4O7 single crystal materials

In this study, the thermoluminescence (TL) characteristics of Ag‐doped and undoped lithium tetraborate (Li₂B₄O₇, LTB) materials, grown using the Czochralski method, were reported. The TL properties of LTB:Ag, such as glow curve structure, dose response, fading and reproducibility, were investigated. The glow curve of the Li₂B₄O₇:Ag single crystal consists of four peaks located at approximately 75, 130, 190 and 275°C; in undoped LTB, the single crystal shows a broad glow curve with peaks at 65, 90, 125, 160 and 190°C using a heating rate of 5°C/s in the 50–350°C temperature region. The high temperature peak of Ag‐doped sample at 275°C has a nonlinear dose response within the range from 33 mGy to 9 Gy. There is a linear response in the range of 33–800 mGy; after which, a sublinear region appears up to 9 Gy for Ag‐doped LTB single crystal. For undoped single crystal, the dose response is supralinear for low doses and linear for the region between 1 and 9 Gy. The thermal fading ratio of the undoped material is almost 60% for the high temperature peak after 7 days. Ag‐doped LTB single crystal exhibits different behaviour over a period of 7 days.     

Thermoluminescence characteristics of calcite with a Gaussian process regression model of machine learning

Thermoluminescence (TL) is defined as a luminescence phenomenon that can be detected when an insulator or semiconductor is thermally stimulated. Defective crystals store radiation until they are stimulated. Thermoluminescence is a method of monitoring the absorbed dose of dosimeters. The irradiation crystal is heated to 500°C to display the absorbed dose as a luminescent light. The TL dosimetric properties of calcite obtained from nature were investigated in this study. Machine learning was also examined using Gaussian process regression (GPR) for stimulated TL characteristics. According to the experimental output, the TL glow curve had two main peaks located at 90°C and 240°C with good dosimetric properties. In the four regression models of GPR, the data for the heating rate of 3°C s⁻¹ have the lowest residual.     

Zinc silicate phosphor: Insights of X-ray induced and temperature enabled luminescence

The present investigation deals with the effect of calcination temperature on the structural and thermoluminescent (TL) properties of Zn₂SiO₄ materials. For this study, Zn₂SiO₄ was prepared via a simple hydrothermal route and calcinated at temperatures from 700°C to 1100°C in an air atmosphere. TL data of all Zn₂SiO₄ samples showed two peaks at around 240°C and 330°C due to the formation of the luminescence centre during X-ray irradiation. More interestingly, the Zn₂SiO₄ sample calcinated at 900°C exhibited a shift in the TL peak (282°C and 354°C) with an optimal TL intensity attributed to its good crystallinity with a well-defined hexagonal plate-like morphology. X-ray-irradiated Zn₂SiO₄ samples calcinated at 900°C exhibited a high-temperature TL glow curve peak, suggesting that the present material could be used for high-temperature dosimetry applications.     

Comparison of thermoluminescence characteristics in γ‐ray and C5+ ion beam‐irradiated LiCaAlF6:Ce phosphor

We compare the thermoluminescence (TL) behavior of Ce³⁺ ion‐activated LiCaAlF₆ exposed to γ‐rays and a carbon ion beam. The reported phosphor is synthesized using an in‐house precipitation method with varying concentrations of activator ion and is characterized by X‐ray diffraction (XRD) and TL. Rietveld refinement is performed to study the structural statistics. The TL glow curve consists of a prominent glow peak at 232°C with three shoulders at 115, 159 and 333°C when exposed to γ‐rays from a ⁶⁰Co source. When exposed to a C⁵⁺ ion beam, the TL glow curve consists of five peaks with peak temperatures near 156, 221, 250, 287 and 330°C, and is found to vary slightly with changing fluence. Glow curve convolution deconvolution (GCCD) functions are applied to the TL curves for complete analysis of the glow curve structure and TL traps. The order of kinetics (b), activation energy (E) and frequency factor are determined using Chen's peak shape method and theoretical curves are drawn using GCCD functions. A track interaction model (TIM) is used to explain the sublinearity/saturation at higher fluences. Ion beam parameters are analyzed using Monte‐Carlo simulation‐based SRIM‐2013 code. Copyright © 2016 John Wiley & Sons, Ltd.     

Evaluation of trapping parameters of γ‐rays irradiated Dy3+‐doped LaPO4 phosphors

Thermoluminescence (TL) materials are widely used in radiation measurements. The best‐known applications of TL materials are in the dosimetry of ionizing radiation, and in CTV screen phosphors, scintillators, X‐ray laser materials, etc. The TL glow curve and its kinetic parameters for annealed LaPO₄ at different constant temperatures and for Dy³⁺‐doped LaPO₄ phosphors irradiated by gamma‐rays are reported here. The samples were irradiated using a ⁶⁰Co gamma‐ray source at a dose of 10 Gy and the heating rate used for TL measurements was 5ºC/s. The samples were characterized using X‐ray diffraction (XRD), Fourier transform infrared, transmission electron microscopy and TL techniques. The XRD pattern shows that the prepared phosphor has a good crystalline structure with an average crystallite size of ~ 18 nm. The samples show good TL peaks for 0.05, 0.1 and 0.2 mole % doping concentrations of Dy³⁺ ions and anneal above 400ºC. The TL glow curve characteristics of annealed LaPO₄ and Dy³⁺‐doped LaPO₄ were analyzed and trapping parameters calculated using various methods. All TL glow curves obey the second‐order kinetics with a single glow peak, which reveals that only one set of trapping parameter is set for a particular temperature. The TL sensitivity was found to depend upon the annealing temperature and Dy³⁺ doping concentration. The prepared sample may be a new nano phosphor and be useful in TL dosimetry. Copyright © 2014 John Wiley & Sons, Ltd.     

Photoluminescence and thermoluminescence dosimetry properties of Ag/Y co-doped ZnO nanophosphor for radiation measurements

This work explores the thermoluminescence (TL) and photoluminescence (PL) properties of Ag/Y co-doped zinc oxide (ZnO) nanophosphor. The proposed dosimeter was prepared by the coprecipitation method and sintered at temperatures from 400°C to 1000°C in an air atmosphere. Raman spectroscopy was studied to investigate the structural features of this composition. The new proposed dosimeter revealed two peaks at 150°C and 175°C with a small shoulder at high temperature (225°C). The PL spectrum showed strong green emissions between 500 to 550 nm. The Raman spectrum showed many bands related to the interaction between ZnO, silver (Ag), and yttrium oxide (Y₂O₃). The rising sintering temperature enhanced the TL glow curve intensity. The Ag/Y co-doped ZnO nanophosphor showed an excellent linearity index within a dose from 1 to 4 Gy. The minimum detectable dose (MDD) of the Ag/Y co-doped ZnO nanopowder (pellets) equaled 0.518 mGy. The main TL properties were achieved in this work as follows: thermal fading (37% after 45 days at 1 and 4 Gy), optical fading (53% after 1 h and 68% after 6 h by exposure to sunlight), effective atomic number (27.6), and energy response (flat behavior from 0.1 to 1.3 MeV). Finally, the proposed material shows promising results nominated to be used for radiation measurements.     

Investigation of thermoluminescence glow curves in quartz extracted from the Central Eastern Desert,Egypt

The current study investigated the thermoluminescence (TL) properties of milky quartz samples collected from the Central Eastern Desert, Egypt. The crystallinity and the elemental concentrations of the milky quartz samples were examined using X‐ray diffraction and an atomic absorption spectrometer. Samples were irradiated using a gamma source at different doses from 250 mGy up to 2 kGy. For annealing, the samples were heated at 400°C for 1 h, followed by slow cooling. Kinetic analyses for the TL glow curves were performed using new designed TL deconvolution software. The glow curves were composed of six overlapped trapping sites at 428, 468, 498, 545, 586, and 639 K. The samples also displayed a linear dose–response from 0.25 Gy up to 20 Gy and a supralinear response from 20 Gy up to 200 Gy. The samples exhibited very low sensitivity for gamma radiation compared with LiF and the minimum detectable dose was 545 μGy. From its linear nature, it was observed that the sensitivity had changed. This study recommends starting measurements of these milky quartz samples after 4 days to give established measurements.     

Optically stimulated luminescence in LiCaAlF6:Eu2+ phosphor

Results on optically stimulated luminescence (OSL) in LiCaAlF₆:Eu²⁺ are reported. Continuous wave OSL signal as recorded using blue (470 nm) stimulation was found to be ~31% that of standard phosphor lithium magnesium phosphate. The rate of OSL depletion for standard phosphor lithium magnesium phosphate is only three times less as compared with that of LiCaAlF₆:Eu²⁺. Strong photoluminescence (PL) in the near ultraviolet region is observed for LiCaAlF₆:Eu²⁺ with the characteristic Eu²⁺ emission at 369 nm for 254 nm excitation. The thermoluminescence (TL) glow peak for LiCaAlF₆:Eu²⁺ was observed at around 180°C. The glow peak was about six times more intense compared with the dosimetric peak of the well known thermoluminescence dosimetric (TLD) phosphor LiF‐TLD 100. Thus this phosphor deserves much more attention than it has received until now and may be useful as a dosimetric material in radiation dosimetry. Copyright © 2015 John Wiley & Sons, Ltd.     

Dosimetric features and kinetic parameters of a glass system dosimeter

Lithium borate (LB) glasses doped with dysprosium oxide (Dy₂O₃) have been prepared by utilizing the conventional melt‐quench technique. The prepared glass samples were exposed to ⁶⁰Co to check their dosimetric features and kinetic parameters. These features involve glow curves, annealing, fading, reproducibility, minimum detectable dose (MDD), and effective atomic number (Z_eff). Kinetic parameters including the frequency factors and activation energy were also determined using three methods (glow curve analysis, initial rise, and peak shape method) and were thoroughly interpreted. In addition, the incorporation of Dy impurities into LB enhanced the thermoluminescence sensitivity ~170 times. The glow from LB:Dy appeared as a single prominent peak at 190°C. The best annealing proceeding was obtained at 300°C for 30 min. Signal stability was reported for a period of 1 and 3 months with a reduction of 26% and 31%, respectively. The proposed glass samples showed promising dosimeter properties that can be recommended for personal radiation monitoring.     

Thermoluminescence in pumice stone collected from the Mediterranean coast

Pumice is a low-density, light-coloured volcanic rock (igneous rock) formed when the magma from a volcanic eruption is suddenly cooled. It has a porous structure and can be different colours and have different densities. Pumice stone, unlike other rock, does not sink in water because it has a low density. In the present study, the thermoluminescent (TL) dosimetric characteristics, such as the dose–response, TL signal fading as a function of storage time, heating rate, and reusability of pumice collected on the Mediterranean coast were investigated. From this study, it was concluded that the pumice stone showed TL properties with a TL glow curve including an obviously wide peak at ∼200°C. A wide linear dose–response region up to 144 Gy, low fading of the TL signal when it was kept in a dark room for a long time, and poor reusability properties were observed for dosimetry use.     

Thermoluminescence properties of the rock naturally annealed for thousands of years by flames from the earth's inner layers

The gas leak in Chimaera near Çıralı, Antalya, has been active for thousands of years. It is also known to be the source of the first Olympic flame in the Hellenistic period. The sample taken from the Chimaere seepage annealed for thousands of years was determined to be calcite-magnesian (Ca, Mg)O₃. In this study, thermoluminescence (TL) properties of calcite-magnesian annealed for thousands of years in the fire caused by methane gas were investigated for particle size, dose–response, heating rate, and fading experiments. It exhibits a clear TL glow curve with two distinct peaks positioned at 160 and 330°C, and its shape is not affected by variation in applied dose and reproduciility of experiment. There is a wide linear relationship between TL output and applied dose up to 614 Gy. Although the positions of the TL peaks are stable with the cycle of measurement, a poor reusability was observed in terms of the area under the TL glow curve and peak intensity.     

Thermoluminescence dosimeter (TLD) studies of Ca10K(PO4)7:Dy phosphor for applications in radiation dosimetry

This study reports the thermoluminescence (TL) aspects of Ca₁₀K(PO₄)₇:Dy phosphor synthesized using a wet chemical method for the first time. The X-ray diffraction (XRD) results confirm the formation of the desired crystalline phase. Surface morphological studies reveal the formation of polyhedrons and agglomerations having an average diameter of 200 nm, while energy dispersive X-ray spectroscopy (EDS) data show the presence and composition of the elements in appropriate amounts. The effect of Dy doping concentration has been studied on the TL properties with exposure to gamma radiations from the Co-60 source. The best TL response has been observed for 5 mol% Dy doping concentration. The glow curve is simple and consists of a single peak at 130°C. The effect of the heating rate has been studied on the TL glow curve, and the heating rate of 5°C/s shows the best TL response. The various TL properties such as annealing conditions, dose–response, TL linearity, fading, and reusability of the prepared phosphor have been studied to check its suitability as a good TL dosimeter (TLD). TL characterization of the phosphor reports that the TL response is linear from 5- to 2000 Gy. The results show that this phosphor can be a good TLD for the dosimetry of gamma radiations from Co-60.     

Synthesis and thermoluminescence characterizations of Sr2B5O9Cl:Dy3+ phosphor for TL dosimetry

The photoluminescence (PL) and thermoluminescence (TL) displayed by Dy‐activated strontium haloborate (Sr₂B₅O₉Cl) were studied. A modified solid‐state reaction was employed for the preparation of the phosphor. Photoluminescence spectra showed blue (484 nm) and yellow (575 nm) emissions due to incorporation of Dy³⁺ into host matrix. The Dy‐doped (0.5 mol%) Sr₂B₅O₉Cl was studied after exposure to γ‐irradiation and revealed a prominent glow curve at 261°C with a small hump around 143°C indicating that two types of traps were generated. The glow peak at the higher temperature side (261°C) was more stable than the lower temperature glow peak. The TL intensity was 1.17 times less than that of the standard CaSO₄:Dy thermoluminescence dosimetry (TLD) phosphor, the phosphor showed a linear dose–response curve for different γ‐ray irradiation doses (0.002–1.25 Gy) and fading of 5–7% was observed for higher temperature peaks upon storage. Trapping parameters and their estimated error values have been calculated by Chen's peak shape method and by the initial rise method. Values of activation energies estimated by both these techniques were comparable. The slight difference in activation energy values calculated by Chen's peak shape method indicated the formation of two kinds of traps Furthermore, slight differences in frequency values are due to various escaping and retrapping probabilities. Copyright © 2014 John Wiley & Sons, Ltd.     

Investigations on the Thermal Stability of Fullerene-Based (Ag-C<Subscript>70</Subscript>) Nanocomposite Thin Films

Fullerene-based bi-functional nanocomposite thin film (Ag nanoparticles embedded in fullerene C₇₀ matrix) is synthesized by thermal co-deposition method. Thermal stability of Ag-C₇₀ nanocomposite is investigated by annealing the nanocomposite thin film at different temperatures from 80 to 350 °C for 30 min. Optical and structural properties of nanocomposite thin film with respect to high temperature are studied by UV-visible spectroscopy and x-ray diffraction, respectively. Transmission electron microscopy is performed to observe the temperature-dependent size evolution of Ag nanoparticles in fullerene C₇₀ matrix. A large growth of Ag nanoparticles is observed with temperature especially above 200 °C due to enhanced diffusion of Ag in fullerene C₇₀ at higher temperature and Ostwald ripening. The properties of metal-fullerene nanocomposite is not significantly affected up to a temperature of 150 °C. With a further increase in temperature, a major blue shift of ~?33 nm in SPR wavelength is seen at a temperature of 300 °C due to the thermal induced structural transformation of fullerene C₇₀ matrix into amorphous carbon. A very large-sized Ag nanoparticle with a wide size distribution varying from 27.8 ± 0.6 to 330.0 ± 4.5 nm is seen at 350 °C and due to which, a red shift of ~?16 nm is obtained at this temperature. This study throws light on the thermal stability of the devices based on metal-fullerene bi-functional nanocomposite.     

Synthesis,characterization and thermoluminescence studies of Mn‐doped ZnS nanoparticles

ZnS:Mn nanoparticles were prepared by a chemical precipitation method and characterized by X‐ray diffraction (XRD), field emission gun scanning electron microscope (FEGSEM), and high resolution transmission electron microscopy (HRTEM). Capping agent (mercaptoethanol) concentrations used were 0 M, 0.005 M, 0.01 M, 0.015 M, 0.025 M, 0.040 M, and 0.060 M, and resulted in nanoparticles sizes of 2.98 nm, 2.9 nm, 2.8 nm, 2.7 nm, 2.61 nm, 2.2 nm and 2.1 nm, respectively. The thermoluminescence (TL) glow curve was recorded by heating the sample exposed to UV‐radiation, at a fixed heating rate 1°C sec^–1. The TL intensity initially increased with temperature, attained a peak value I_m for a particular temperature, and then decreased with further increase in temperature. The peak TL intensity increased with decreasing nanoparticle size, whereas the temperature corresponding to the peak TL intensity decreased slightly with reducing nanocrystal size. As a consequence of increase in surface‐to‐volume ratio and increased carrier recombination rates, the TL intensity increased with decreasing nanoparticle size. It was found that, whereas activation energy slightly decreased with decreasing nanoparticle size, the frequency factor decreased significantly with reduction in nanoparticle size. Copyright © 2015 John Wiley & Sons, Ltd.     

The dosimetric properties of phosphate glass systems prepared by different chemical nanomaterials

The synthesis and characterization of glass systems were carried out using prepared nanocrystals injected into a glass matrix as a thermoluminescence (TL) activator using the melt–quenching method. Sample 1 was prepared as [40P₂O₅ 50BaO:2.5MgO, 2.5Na₂O, 5TiO₂], sample 2 as [37.5P₂O₅ 37.5CaO:25TiO₂] and sample 3 as [50P₂O₅–50Li₂O]. Formation of the synthesized compound was confirmed by studying the X‐ray diffraction (XRD) patterns and scanning electron microscopy (SEM) images. An annealing procedure was carried out for 1 h at 400 °C. The glow curve position and shape shifted dramatically and linearly to the higher temperature values on increasing the heating rate. A heating rate of 30 °C/s was the most suitable for obtaining a high TL response. Samples 2 and 3 have the highest TL response, which approached the effective atomic number (Z_eff) of natural bone. The observed TL sensitivity of the prepared samples 2 and 3 is less than that of commercially available ‘TLD‐200 chips’ and LiF:Mg,Ti (TLD‐100) phosphor. Sample [37.5P₂O₅ 37.5CaO:25TiO₂] would be useful in personal and environmental dosimetry for measuring high doses of gamma radiation. Sample [50P₂O₅–50Li₂O] is a good dosimeter, although it requires the addition of an appropriate transitional metal (activator) to overcome the problem of high fading. Copyright © 2016 John Wiley & Sons, Ltd.     

Dosimetric properties of lithium borate glass doped with dysprosium

Characterization of thermoluminescence (TL) properties of lithium borate glass samples doped with different concentrations of dysprosium (Dy) was carried out. Samples were prepared using a melting method at 1100°C and irradiated with β‐particles. The glass samples doped with 0.1% Dy displayed the best TL dosimetric properties compared with other compositions. Deconvoluted analyses of the glow curves displayed five overlapping TL glow peaks located between 392.0 and 510.3 K. A good linear TL dose–response for β‐particles was obtained in the dose range 66.6 mGy to 33.3 Gy. The minimum detectible dose was evaluated to be 205.4 μGy and samples revealed thermal fading in 312 h to 29% of their original value.     

Thermoluminescence properties of gamma‐irradiated nano‐structure hydroxyapatite

The suitability of nano‐structured hydroxyapatite (HAP) for use as a thermoluminescence dosimeter was investigated. HAP samples were synthesized using a hydrolysis method. The formation of nanoparticles was confirmed by X‐ray diffraction and average particle size was estimated to be ~30 nm. The glow curve exhibited a peak centered at around 200 °C. The additive dose method was applied and this showed that the thermoluminescence (TL) glow curves follow first‐order kinetics due to the non‐shifting nature of T_m after different doses. The numbers of overlapping peaks and related kinetic parameters were identified from T_m–T_stop through computerized glow curve deconvolution methods. The dependence of the TL responses on radiation dose was studied and a linear dose response up to 1000 Gy was observed for the samples. Copyright © 2015 John Wiley & Sons, Ltd.     

Mechanoluminescence,thermoluminescence, photoluminescence studies on Ca3Y2Si3O12:RE3+ (RE3+ = Dy3+and Eu3+) phosphors

Dy³⁺ and Eu³⁺ activated Ca₃Y₂Si₃O₁₂ phosphors were synthesized by the solid‐state synthesis method. The phosphors were characterized by X‐ray diffraction (XRD), mechanoluminescence (ML), thermoluminescence (TL) and photoluminescence (PL) to determine structure and luminescence. For ML glow curves, only one peak was observed, as only one type of luminescence centre was formed during irradiation. The Ca₃Y₂Si₃O₁₂:Dy³⁺ TL glow curve showed a single peak at 151.55°C and the Ca₃Y₂Si₃O₁₂:Eu³⁺ TL glow curve peaked at 323°C with a small peak at 192°C, indicating that two types of traps were activated. The trapping parameters for both the samples were calculated using Chen's peak shape method. Dy³⁺‐activated Ca₃Y₂Si₃O₁₂ showed emission at 482 and 574 nm when excited by a 351 nm excitation wavelength, whereas the Eu³⁺‐activated Ca₃Y₂Si₃O₁₂ phosphor PL emission spectra showed emission peaks at 613 nm, 591 nm, 580 nm when excited at 395 nm wavelength. When excited at 466 nm, prominent emission peaks were observed at their respective positions with very slight shifts. Copyright © 2015 John Wiley & Sons, Ltd.