Comparison of luminescence property of gamma‐ray irradiated Tb3+‐doped and Ce3+ co‐doped potassium halide single crystals

Single crystals of KCl and KBr singly and doubly doped with Tb³⁺ and Ce³⁺, respectively, were successfully grown using the Bridgeman technique. This work reports the comparative luminescence behavior and optical absorption characterization of non‐irradiated and γ‐ray‐irradiated single crystals of these materials. The existing defect and the defect created by γ‐ray irradiation were monitored by optical absorption spectra. The excitation and emission spectra of these materials were measured at room temperature with a spectrofluorometer and the pertaining results were compared. The F‐band comparison was made when bleached with F‐light for 2 mins. The trap‐level changes in KCl and KBr when it is singly and doubly doped enabled us to draw conclusions on the nature of the defect and on the recombination processes involved.     

Thermoluminescence and photoluminescence studies on γ‐ray‐irradiated Ce3+,Tb3+‐doped potassium chloride single crystals

Single crystals of KCl doped with Ce³⁺,Tb³⁺ were grown using the Bridgeman–Stockbarger technique. Thermoluminescence (TL), optical absorption, photoluminescence (PL), photo‐stimulated luminescence (PSL), and thermal‐stimulated luminescence (TSL) properties were studied after γ‐ray irradiation at room temperature. The glow curve of the γ‐ray‐irradiated crystal exhibits three peaks at 420, 470 and 525 K. F‐Light bleaching (560 nm) leads to a drastic change in the TL glow curve. The optical absorption measurements indicate that F‐ and V‐centres are formed in the crystal during γ‐ray irradiation. It was attempted to incorporate a broad band of cerium activator into the narrow band of terbium in the KCl host without a reduction in the emission intensity. Cerium co‐doped KCl:Tb crystals showed broad band emission due to the d–f transition of cerium and a reduction in the intensity of the emission peak due to ⁵D₃–⁷F_j (j = 3, 4) transition of terbium, when excited at 330 nm. These results support that energy transfer occurs from cerium to terbium in the KCl host. Co‐doping Ce³⁺ ions greatly intensified the excitation peak at 339 nm for the emission at 400 nm of Tb³⁺. The emission due to Tb³⁺ ions was confirmed by PSL and TSL spectra. Copyright © 2015 John Wiley & Sons, Ltd.     

Luminescence characterization of Dy and Eu doped Na6Mg(SO4)4 phosphors

A series of single‐phase phosphors based on Na₆Mg(SO₄)₄ (Z_eff = 11.70) doped with Dy and Eu was prepared by the wet chemical method. The photoluminescence (PL) and thermoluminescence (TL) properties of Dy³⁺‐ and Eu³⁺‐activated Na₆Mg(SO₄)₄ phosphors were investigated. The characteristic emissions of Dy³⁺ and Eu³⁺ were observed in the Na₆Mg(SO₄)₄ host. The TL glow curve of the Na₆Mg(SO₄)₄:Dy phosphor consisted of a prominent peak at 234°C and a very small hump at 158°C. The TL sensitivity of the Na₆Mg(SO₄)₄:Dy phosphor was found to be four times less than the commercialized CaSO₄:Dy phosphor. The TL dose–response of the Na₆Mg(SO₄)₄:Dy phosphor was studied from a dose range of 5–10 kGy and the linear dose–response was observed up to 1 kGy which is good for a microcrystalline phosphor. Trapping parameters for both the samples were calculated using the Initial Rise and Chen's peak shape methods.     

Mechanoluminescence,thermoluminescence, photoluminescence studies on Ca3Y2Si3O12:RE3+ (RE3+ = Dy3+and Eu3+) phosphors

Dy³⁺ and Eu³⁺ activated Ca₃Y₂Si₃O₁₂ phosphors were synthesized by the solid‐state synthesis method. The phosphors were characterized by X‐ray diffraction (XRD), mechanoluminescence (ML), thermoluminescence (TL) and photoluminescence (PL) to determine structure and luminescence. For ML glow curves, only one peak was observed, as only one type of luminescence centre was formed during irradiation. The Ca₃Y₂Si₃O₁₂:Dy³⁺ TL glow curve showed a single peak at 151.55°C and the Ca₃Y₂Si₃O₁₂:Eu³⁺ TL glow curve peaked at 323°C with a small peak at 192°C, indicating that two types of traps were activated. The trapping parameters for both the samples were calculated using Chen's peak shape method. Dy³⁺‐activated Ca₃Y₂Si₃O₁₂ showed emission at 482 and 574 nm when excited by a 351 nm excitation wavelength, whereas the Eu³⁺‐activated Ca₃Y₂Si₃O₁₂ phosphor PL emission spectra showed emission peaks at 613 nm, 591 nm, 580 nm when excited at 395 nm wavelength. When excited at 466 nm, prominent emission peaks were observed at their respective positions with very slight shifts. Copyright © 2015 John Wiley & Sons, Ltd.     

Optical analysis of RE3+ (RE = Pr3+, Er3+ and Nd3+):cadmium lead boro tellurite glasses

This article reports on the optical characterization of Pr³⁺‐, Er³⁺‐ and Nd³⁺‐doped cadmium lead boro tellurite (CLBT) glasses prepared using the melt quenching method. The visible–near infrared (Vis–NIR) absorption spectra of these glasses were analyzed systematically. On measuring the NIR emission spectra of Er³⁺:CLBT glasses, a broad emission band centered at 1536 nm (⁴I_13/2 → ⁴I_15/2) was observed, as were three NIR emission bands at 900 nm (⁴F_3/2 → ⁴I_9/2), 1069 nm (⁴F_3/2 → ⁴I_11/2) and 1338 nm (⁴F_3/2 → ⁴I_13/2) from Nd³⁺:CLBT glasses and an NIR emission band at 1334 nm (¹G₄ → ³H₅) from Pr³⁺:CLBT glasses at an excitation wavelength (λ_ex) of 514.5 nm (Ar⁺ laser). Copyright © 2016 John Wiley & Sons, Ltd.     

Luminescence study of Dy or Ce activated LiCaBO3 phosphor for γ‐ray and C5+ ion beam irradiation

The photoluminescence and thermoluminescence characteristics of rare earths (Dy or Ce) activated LiCaBO₃ phosphors have been studied. Phosphors were synthesized by modified solid state synthesis. The phosphors were characterized by X‐ray diffraction (XRD), scanning electron microscopy (SEM), photoluminescence (PL) and thermoluminescence (TL) for structural, morphological and luminescence studies. Dy³⁺ activated LiCaBO₃ shows emission at 486 and 577 nm due to ⁴ F_9/2 → ⁶H_15/2 and ⁴ F_9/2 → ⁶H_13/2 transition, respectively, whereas the PL emission spectra of Ce³⁺ activated LiCaBO₃ phosphor shows a broad band peaking at 432 nm, which is due to the transition from 5d level to the ground state of the Ce³⁺ ion. The thermoluminescence study was also carried out for both these phosphors for γ‐ray irradiation and carbon beam irradiation. Linearity was studied for a 0.4–3.1 Rad dose γ‐rays. Linear behaviour over this dose range was observed. Gamma ray‐irradiated phosphors were shown to be negligible fading upon storage. All the samples were also studied for 75 MeV C⁵⁺ ion beam exposure in the range of 3.75 × 10¹² – 7.5 × 10¹³ ion cm^–2 fluence. In addition to this, trapping parameters of all the samples were also calculated using Chen's peak shape method. Copyright © 2015 John Wiley & Sons, Ltd.     

Synthesis and characterization of novel Na15(SO4)5F4Cl:Ce3+ halosulfate phosphors

A series of Na₁₅(SO₄)₅F₄Cl phosphors doped with Ce³⁺ ions was prepared using the wet chemical method. X‐Ray diffraction studies were used to determine their phase formation and purity. Fourier transform infrared spectroscopy effectively identified the chemical bonds present in the molecule. The photoluminescence properties of the as‐prepared phosphors were investigated and the Ce³⁺ ions in these hosts were found to give broadband emission in the UV range. For the thermoluminescence study, phosphors were irradiated with a 5 Gy dose of γ‐rays from a ⁶⁰Co source. Chen’s half‐width method was employed to calculate the trapping parameters from the thermoluminescence glow curve. Copyright © 2016 John Wiley & Sons, Ltd.     

Structural characterization of Er3+,Yb3+‐doped Gd2O3 phosphor,synthesized using the solid‐state reaction method,and its luminescence behavior

We report the synthesis and structural characterization of Er³⁺,Yb³⁺‐doped Gd₂O₃ phosphor. The sample was prepared using the conventional solid‐state reaction method, which is the most suitable method for large‐scale production. The prepared phosphor sample was characterized using X‐ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR), thermoluminescence (TL), photoluminescence (PL) and CIE techniques. For PL studies, the excitation and emission spectra of Gd₂O₃ phosphor doped with Er³⁺ and Yb³⁺ were recorded. The excitation spectrum was recorded at a wavelength of 551 nm and showed an intense peak at 276 nm. The emission spectrum was recorded at 276 nm excitation and showed peaks in all blue, green and red regions, which indicate that the prepared phosphor may act as a single host for white light‐emitting diode (WLED) applications, as verified by International de I'Eclairage (CIE) techniques. From the XRD data, the calculated average crystallite size of Er³⁺ and Yb³⁺‐doped Gd₂O₃ phosphor is ~ 38 nm. A TL study was carried out for the phosphor using UV irradiation. The TL glow curve was recorded for UV, beta and gamma irradiations, and the kinetic parameters were also calculated. In addition, the trap parameters of the prepared phosphor were also studied using computerized glow curve deconvolution (CGCD). Copyright © 2015 John Wiley & Sons, Ltd.     

Synthesis and characterization of KCe(PO3)4 doped with some lanthanide activators

KCe(PO₃)₄ doped with Dy³⁺,Tb³⁺,Yb³⁺and Nd³⁺ phosphors were synthesized by a solid state diffusion method. The prepared samples were characterized by X‐ray diffraction and photoluminescence. KCe(PO₃)₄ exhibits emission in ultraviolet (UV) region which indicates weak Ce³⁺–Ce³⁺ interaction. The Ce³⁺–Ce³⁺energy transfer is not efficient. In light of this, energy transfer from Ce³⁺ to other lanthanides like Dy³⁺, Tb³⁺,Yb³⁺ and Nd³⁺ is rather surprising.     

Luminescence and energy transfer in Ce3+, Mn2+‐doped K2AEP2O7 (AE = Ca,Sr) phosphor

Pyrophosphates K₂AEP₂O₇ (AE = Ca, Sr) prepared by the classical solid‐state technique and activated with Ce³⁺ are described. Intense emission was observed in K₂AEP₂O₇ (AE = Ca, Sr). The effect of Mn²⁺ co‐doping was studied. The broad emission peak of Mn²⁺ was observed at 534 nm in K₂SrP₂O₇:Ce³⁺ and at 539 nm in K₂CaP₂O₇:Ce³⁺, Mn²⁺. Mn²⁺ emission was greatly enhanced by addition of the sensitizer Ce³⁺ due to efficient energy transfer from Ce³⁺ to Mn²⁺. Copyright © 2015 John Wiley & Sons, Ltd.     

Rare earth thiocyanate complexes with tripiperidinophosphine oxide: synthesis and characterization. Crystal structure of Pr(SCN)3(tpppO)3

The synthesis and characterization of rare-earth (La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, Yb, Lu and Y) thiocyanate adducts with tripiperidinophosphine oxide (tpppO) with general formula (RE)(SCN)₃(tpppO)₃ are reported. Conductance measurements in acetonitrile indicate the non-electrolytic nature of the complexes. Infrared absorption spectra evidence that the SCN⁻ ion coordinates through the nitrogen atom (isothiocyanate form) and that tpppO coordinates through the phosphoryl oxygen. X-ray powder patterns suggest the existence of three different crystal forms: (1) La; (2) an isomorphous series including Ce, Nd and Pr; and (3) another isomorphous series, including Sm, Gd, Eu, Ho, Er, Tb, Lu and Y. The visible spectra of the Nd adduct and the calculated parameters β = 0.98, b^1/2 = 0.072 and δ = 1.06 indicate that the metal-ligand bonds are essentially electrostactic. The emission spectra of the Eu compound showed ⁵D₀ → ⁷F_J bands (J = 0, 1, 2), suggesting a C_3v symmetry for the coordination polyhedron. The lifetime of the ⁵D₀ state is 1.28 ms. The emission spectra of the Tb complex presented ⁵D₄ → ⁷F_J bands (J = 4, 5, 6) and the Dy complex showed the ⁴F_9/2 → ⁶H_13/2 band. The structure of the Pr complex showed that the coordination polyhedron is a trigonal antiprism, with the isothiocyanate anions in one base and three tpppO ligands in the other. Thermal analyses (TG-DTG) were carried out for the Ce, Nd and Gd adducts. Mass losses start between 250 and 334 °C. The final residues at 1300 °C are the corresponding phosphates.     

Photoluminescence and structural analysis of trivalent europium doped MLaAl3O7 (M = Ba,Ca, Mg and Sr) nanophosphors

The solution combustion technique was used to synthesize MLaAl₃O₇ (M = Ba, Ca, Mg, and Sr) nanophosphors‐doped with Eu³⁺ using metal nitrates as precursors. The photoluminescence (PL) emission spectra exhibited three peaks at 587–591, 610–616, and 653–654 corresponding to ⁵D₀→⁷F₁, ⁵D₀→⁷F₂, and ⁵D₀→⁷F₃ transitions, respectively. Upon excitation at 254 nm, these nanophosphors displayed strong red emission with the dominant peak attributed to the ⁵D₀→⁷F₂ transition of Eu³⁺. The materials were further heated at 900 and 1050°C for 2 h to examine the consequence of temperature on crystal lattice and PL emission intensity. X‐ray diffraction (XRD) analysis proved that all the synthesized materials were of a crystalline nature. CaLaAl₃O₇ material has a tetragonal crystal structure with space group P421m. Scherer's equation was used to calculate the crystallite size of synthesized phosphors using XRD data. A Fourier transformation infrared study was used to observe the stretching vibrations of metal–oxygen bonds. Infrared peaks for stretching vibrations corresponding to lanthanum–oxygen and aluminium–oxygen bonds were found at 582 and 777 cm^–1 respectively for CaLaAl₃O₇ phosphor material. Transmission electron microscopy images were used to determine the size of particles (18–37 nm for the as‐prepared materials) and also to analyze the three‐dimensional view of these materials. The experimental data indicate that these materials may be promising red‐emitting nanophosphors for use in white light‐emitting diodes.     

Effect of γ‐irradiation on thermal and thermoluminescence properties of polystyrene/europium (III) oxide composite film

In the present study, polystyrene:europium (III) oxide polymer films at a ratio of 95:5 wt% were prepared using a solution casting technique. These polymeric films were irradiated with 5, 25 and 50 kGy γ‐radiation doses and their thermoluminescence (TL) and thermal properties were studied as a function of radiation dose. Analysis of Fourier transform infrared spectra revealed different modes of vibration and polymer–filler interaction. Reduction of vibrational modes with radiation dose was observed. The TL glow curve intensity was observed to increase with increasing radiation dose and to become broader in the 378 K and 444 K regions. Detrapping of electrons implied by the glow curve was caused by thermally induced macromolecular motion, concurrent with β‐relaxation in polystyrene. The TL glow curve parameters were computed using a glow curve deconvolution method. Differential scanning calorimetry analysis indicated that the glass transition temperature (T_g) increased with increase in dose, suggesting crosslinking of the polymer chain. Scanning electron microscopy analysis evidenced the change in surface morphology due to γ‐irradiation.     

Energy transfer induced white‐light‐emitting phosphor by co‐doping Ce3+, Tb3+ and Mn2+ into the single Ba9Lu2Si6O24 host

In the Ba₉Lu₂Si₆O₂₄ (BLS) host, Ce³⁺ shows cyan emissions peaking at 490 nm under 400 nm excitations. BLS:Tb³⁺ only can be effectively excited by 254 nm light and gives rise to green emissions at 553 nm. However, both the cyan and green emissions can be obtained in BLS:Ce³⁺,Tb³⁺ under 400 nm excitations due to effective energy transfers from Ce³⁺ to Tb³⁺. BLS:Mn²⁺ shows red emissions peaking at 610 nm under 414 nm excitations. By co‐doping Ce³⁺, Tb³⁺ and Mn²⁺, tunable full‐color emissions were obtained. The BLS:0.3Ce³⁺,0.6Tb³⁺,0.15Mn²⁺ single phosphor exhibits a white light with a high color rendering index of 85 and a correlated color temperature of 5480 K under 400 nm excitation.     

Effect of Ga3+ and Gd3+ ions substitution on the structural and optical properties of Ce3+‐doped yttrium aluminium garnet phosphor nanopowders

The structural and optical properties of commercially obtained Y₃Al₅O₁₂:Ce³⁺ phosphor were investigated by replacing Al³⁺ with Ga³⁺ and Y³⁺ with Gd³⁺ in the Y₃Al₅O₁₂:Ce³⁺ structure to form Y₃(Al,Ga)₅O₁₂:Ce³⁺ and (Y,Gd)₃Al₅O₁₂:Ce³⁺. X‐Ray diffraction (XRD) results showed slight 2‐theta peak shifts to lower angles when Ga³⁺ was used and to higher angles when Gd³⁺ was used, with respect to peaks from Y₃Al₅O₁₂:Ce³⁺ and JCPDS card no. 73–1370. This could be attributed to induced crystal‐field effects due to the different ionic sizes of Ga³⁺ and Gd³⁺ compared with Al³⁺ and Y³⁺. The photoluminescence (PL) spectra showed broad excitation from 350 to 550 nm with a maximum at 472 nm, and broad emission bands from 500 to 650 nm, centred at 578 nm for Y₃Al₅O₁₂:Ce³⁺ arising from the 5d → 4f transition of Ce³⁺. PL revealed a blue shift for Ga³⁺ substitution and a red shift for Gd³⁺ substitution. UV–Vis showed two absorption peaks at 357 and 457 nm for Y₃Al₅O₁₂:Ce³⁺, with peaks shifting to 432 nm for Ga³⁺ and 460 nm for Gd³⁺ substitutions. Changes in the trap levels or in the depth and number of traps due to Ce³⁺ were analysed using thermoluminescence (TL) spectroscopy. This revealed the existence of shallow and deep traps. It was observed that Ga³⁺ substitution contributes to the shallowest traps at 74 °C and fewer deep traps at 163 °C, followed by Gd³⁺ with shallow traps at 87 °C and deep traps at 146 °C. Copyright © 2016 John Wiley & Sons, Ltd.     

Na+:HCO(3-) cotransporters (NBC): cloning and characterization

The sodium bicarbonate cotransporter (NBC1) is essential for bicarbonate transport across plasma membranes in epithelial and nonepithelial cells. The direction of the NaHCO₃ movement in secretory epithelia is opposite to that in reabsorptive epithelia. In secretory epithelia (such as pancreatic duct cells) NBC is responsible for the transport of bicarbonate from blood to the cell for eventual secretion at the apical membrane. In reabsorptive epithelia (such as kidney proximal tubule cells) NBC is responsible for the reabsorption of bicarbonate from cell to the blood. In nonepithelial cells this transporter is mainly involved with cell pH regulation. Recent molecular cloning experiments have identified the existence of four NBC isoforms (NBC1, 2, 3 and 4) and two NBC-related proteins AE4 and NCBE (Anion Exchanger 4 and Na-dependent Chloride-Bicarbonate Exchanger). All but AE4 are presumed to mediate the cotransport of Na⁺ and HCO₃ ⁻ under normal conditions and may be functionally altered in certain pathologic states. NBC1 shows a limited tissue expression pattern, is electrogenic and plays an important role in bicarbonate reabsorption in kidney proximal tubule. In addition to the kidney, NBC1 is expressed in pancreatic duct cells, is activated by cystic fibrosis transmembrane conductance regulator (CFTR) and plays an important role in HCO₃ ⁻ secretion. NBC2 and NBC3 have a wider tissue distribution than NBC1, are electroneutral, and are involved with cell pH regulation. The characterization of NBC4 is incomplete. The NBC-related protein called NCBE mediates Na-dependent, Cl⁻/Bicarbonate Exchange. The purpose of this review is to summarize recent advances on the cloning of NBC isoforms and related proteins and their role and regulation in physiologic and pathologic states. Received: 26 February 2001/Revised: 14 May 2001     

喷施吲哚-3-乙酸 (IAA) 对番茄及其上B型烟粉虱的影响

【目的】不同植物生长调节物质对植食性昆虫产卵、发育、取食等常有促进或抑制作用,进而影响植物与昆虫的互作关系。本研究旨在阐明常用的植物生长调节剂吲哚-3-乙酸对B型烟粉虱Bemisia tabaci (Gennadius)的影响,进而探索防治烟粉虱环境友好的方法,同时期望获得更加优质的烟粉虱用作替代寄主饲养寄生蜂。【方法】对番茄 Solanum lycopersicum L.植株外源喷施吲哚-3-乙酸(IAA),检测其生理生化的响应;记录B型烟粉虱存活率、产卵量并测量解毒酶等指标。【结果】喷施IAA后番茄叶片含水量略有上升,叶面积增大,叶绿素含量增加,过氧化物酶(POD)活性降低,多酚氧化酶(PPO)活性升高,超氧化物歧化酶(SOD)活性变化不显著(P＞0.05)。喷施IAA后番茄上B型烟粉虱成虫存活率高于对照组,其中50 mg/L IAA番茄上B型烟粉虱成虫存活率和总产卵量最高,250 mg/L IAA存活率最低;喷施IAA 120 h后烟粉虱总产卵量升高;碱性磷酸酶(AKP)、超氧化物歧化酶(SOD)活性较对照升高。【结论】喷施不同浓度的IAA溶液后,番茄植株的生理生化水平发生不同程度的改变,烟粉虱成虫的存活状况、产卵量以及体内解毒活性也会产生不同程度的改变。适宜剂量的IAA处理能够使烟粉虱的生存表现更加优异,从而为饲养寄生蜂提供优质的替代寄主。     

Exceptionally Enhanced Electrode Activity of (Pr,Ce)O2−δ‐Based Cathodes for Thin‐Film Solid Oxide Fuel Cells

It is shown that an electrochemically‐driven oxide overcoating substantially improves the performance of metal electrodes in high‐temperature electrochemical applications. As a case study, Pt thin films are overcoated with (Pr,Ce)O_2?δ (PCO) by means of a cathodic electrochemical deposition process that produces nanostructured oxide layers with a high specific surface area and uniform metal coverage and then the coated films are examined as an O₂‐electrode for thin‐film‐based solid oxide fuel cells. The combination of excellent conductivity, reactivity, and durability of PCO dramatically improves the oxygen reduction reaction rate while maintaining the nanoscale architecture of PCO layers and thus the performance of the PCO‐coated Pt thin‐film electrodes at high temperatures. As a result, with an oxide coating step lasting only 5 min, the electrode resistance is successfully reduced by more than 1000 times at 500 °C in air. These observations provide a new direction for the design of high‐performance electrodes for high‐temperature electrochemical cells.     

Photoluminescence and electron paramagnetic resonance properties of a potential phototherapic agent: MMgF4:Gd3+ (M = Ba,Sr) sub‐microphosphors

Novel narrow band UVB‐emitting phosphors, BaMgF₄:Gd³⁺ and SrMgF₄:Gd³⁺ phosphors, were synthesized using a co‐precipitation synthesis method. X‐Ray diffraction analysis was carried out to confirm compound formation, phase purity and crystallinity of the phosphor. At 274 nm excitation, phosphors show a sharp narrow band emission at 313 nm that can be assigned to ⁶P_7/2 → ⁸S_7/2 transition of the Gd³⁺ ion. With increasing dopant concentration, intensity enhances and then decreases after a certain concentration, which is an indication of concentration quenching taking place in the phosphor. Scanning electron microscopy images of the phosphor show agglomerated particles in the sub‐micron range. Particles range in size from 600 to 800 nm. Electron paramagnetic resonance studies of the phosphors were carried out to detect radicals present in the prepared phosphor. With narrow band UVB emission, phosphor seems to be a good candidate for UV phototherapy application. Copyright © 2016 John Wiley & Sons, Ltd.