Influence of anodic biofilm growth on bioelectricity production in single chambered mediatorless microbial fuel cell using mixed anaerobic consortia

The effect of anodic biofilm growth and extent of its coverage on the anodic surface of a single chambered mediatorless microbial fuel cell (MFC) was evaluated for bioelectricity generation using designed synthetic wastewater (DSW) and chemical wastewater (CW) as substrates and anaerobic mixed consortia as biocatalyst. Three MFCs (plain graphite electrodes, air cathode, Nafion membrane) were operated separately with variable biofilm coverage [control; anode surface coverage (ASC), 0%], partially developed biofilm [PDB; ASC approximately 44%; 90 days] and fully developed biofilm [FDB; ASC approximately 96%; 180 days] under acidophilic conditions (pH 6) at room temperature. The study depicted the effectiveness of anodic biofilm formation in enhancing the extracellular electron transfer in the absence of mediators. Higher specific power production [29mW/kg COD(R) (CW and DSW)], specific energy yield [100.46J/kg VSS (CW)], specific power yield [0.245W/kg VSS (DSW); 0.282W/kg VSS (CW)] and substrate removal efficiency of 66.07% (substrate degradation rate, 0.903kgCOD/m(3)-day) along with effective functioning fuel cell at relatively higher resistance [4.5kOmega (DSW); 14.9kOmega (CW)] correspond to sustainable power [0.008mW (DSW); 0.021mW (CW)] and effective electron discharge (at higher resistance) and recovery (Coulomb efficiency; 27.03%) were observed especially with FDB operation. Cyclic voltammetry analysis documented six-fold increment in energy output from control (1.812mJ) to PDB (10.666mJ) operations and about eight-fold increment in energy from PDB to FDB (86.856mJ). Biofilm configured MFC was shown to have the potential to selectively support the growth of electrogenic bacteria with robust characteristics, capable of generating higher power yields along with substrate degradation especially operated with characteristically complex wastewaters as substrates.     

Bioelectricity production from wastewater treatment in dual chambered microbial fuel cell (MFC) using selectively enriched mixed microflora: Effect of catholyte

The performance of aerated and ferricyanide catholytes on the bioelectricity production was evaluated in dual chambered microbial fuel cell (MFC) (mediatroless anode; graphite electrodes) employing selectively enriched H(2) producing mixed consortia as anodic inoculum. Two MFCs with aerated catholyte (MFC(AC)) and ferricyanide catholyte (MFC(FC)) were operated separately to elucidate the difference in power generation potential and carbon removal efficiency under similar operating conditions [ambient pressure; room temperature (28+/-2 degrees C); acidophilic microenvironment (pH 6)]. The experimental data demonstrated the feasibility of in situ bioelectricity generation along with wastewater treatment. Effective power generation and substrate removal efficiency was documented in the fuel cell operated with ferricyanide catholyte (586 mV; 2.37 mA; 0.559 kg COD/m(3) day) than aerated catholyte (572 mV; 1.68 mA; 0.464 kg COD/m(3) day). Maximum power yield (0.635 W/kg COD(R) and 0.440 W/kg COD(R)) and current density (222.59 mA/m(2) and 190.28 mA/m(2)) was observed at 100 Omega resistor with ferricyanide and aerated catholytes, respectively. The study documented both wastewater treatment and electricity production through direct conversion of H(2) in a single system.     

Power overshoot in two-chambered microbial fuel cell (MFC)

A two-chamber microbial fuel cell was started using iron-reducing strains as inoculum and acetate as carbon sources. The tested microbial fuel cell had an open-circuit voltage of 0.67 V, and reached 1045 mA m⁻² and a power density of 486 mW m⁻² at 0.46 V before power overshoot occurred. Anodic reactions were identified as the rate-determining steps. Stirring the anolyte insignificantly increased cell performance, suggesting a minimal external mass transfer resistance from the anolyte to the anodic biofilm. Data regression analysis indicates that charge transfer resistance at the biofilm-anode junction was negligible. The order of magnitude estimation of electrical conductance indicates that electron transfer resistance had an insignificant effect on microbial fuel cell performance. Resistance in electrogens for substrate utilization is proposed to induce microbial fuel cell power overshoot.     

Upflow bio-filter circuit (UBFC): biocatalyst microbial fuel cell (MFC) configuration and application to biodiesel wastewater treatment

A biodiesel wastewater treatment technology was investigated for neutral alkalinity and COD removal by microbial fuel cell. An upflow bio-filter circuit (UBFC), a kind of biocatalyst MFC was renovated and reinvented. The developed system was combined with a pre-fermented (PF) and an influent adjusted (IA) procedure. The optimal conditions were operated with an organic loading rate (OLR) of 30.0 g COD/L-day, hydraulic retention time (HRT) of 1.04 day, maintained at pH level 6.5-7.5 and aerated at 2.0 L/min. An external resistance of circuit was set at 10 k?. The purposed process could improve the quality of the raw wastewater and obtained high efficiency of COD removal of 15.0 g COD/L-day. Moreover, the cost of UBFC system was only US$1775.7/m3 and the total power consumption was 0.152 kW/kg treated COD. The overall advantages of this invention are suitable for biodiesel wastewater treatment.     

From microbial fuel cell (MFC) to microbial electrochemical snorkel (MES): maximizing chemical oxygen demand (COD) removal from wastewater

The paper introduces the concept of the microbial electrochemical snorkel (MES), a simplified design of a "short-circuited" microbial fuel cell (MFC). The MES cannot provide current but it is optimized for wastewater treatment. An electrochemically active biofilm (EAB) was grown on graphite felt under constant polarization in an urban wastewater. Controlling the electrode potential and inoculating the bioreactor with a suspension of an established EAB improved the performance and the reproducibility of the anodes. Anodes, colonized by an EAB were tested for the chemical oxygen demand (COD) removal from urban wastewater using a variety of bio-electrochemical processes (microbial electrolysis, MFC, MES). The MES technology, as well as a short-circuited MFC, led to a COD removal 57% higher than a 1000 Ω-connected MFC, confirming the potential for wastewater treatment.     

From microbial fuel cell (MFC) to microbial electrochemical snorkel (MES): maximizing chemical oxygen demand (COD) removal from wastewater

The paper introduces the concept of the microbial electrochemical snorkel (MES), a simplified design of a “short-circuited” microbial fuel cell (MFC). The MES cannot provide current but it is optimized for wastewater treatment. An electrochemically active biofilm (EAB) was grown on graphite felt under constant polarization in an urban wastewater. Controlling the electrode potential and inoculating the bioreactor with a suspension of an established EAB improved the performance and the reproducibility of the anodes. Anodes, colonized by an EAB were tested for the chemical oxygen demand (COD) removal from urban wastewater using a variety of bio-electrochemical processes (microbial electrolysis, MFC, MES). The MES technology, as well as a short-circuited MFC, led to a COD removal 57% higher than a 1000 Ω-connected MFC, confirming the potential for wastewater treatment.     

微生物燃料电池在固体废物堆肥中的应用进展

微生物燃料电池(Microbial fuel cell,MFC)是一种近几年快速发展的废物处理与能源化技术,可以与污水处理、污染物降解、脱盐等环境技术结合。微生物燃料电池与堆肥技术结合可以在处理日益增长的固体废弃物的同时回收能量,具有很好的发展前景。文中分析了堆肥微生物燃料电池系统的微生物特征,探讨了堆肥过程中影响微生物燃料电池产电性能的因素,包括电极,隔膜,供氧和构型。最后归纳说明了堆肥微生物电池作为一种新的废弃物处理技术的特点:较高的微生物量并可产生较高的电流密度;对不同环境的适应性强;可以自身调节温度,能源利用效率高;质子从阳极向阴极的移动会受到不同堆肥原料的影响。     

Coupling microbial fuel cells with a membrane photobioreactor for wastewater treatment and bioenergy production

Microbial fuel cells (MFCs) and membrane photobioreactors are two emerging technologies for simultaneous wastewater treatment and bioenergy production. In this study, those two technologies were coupled to form an integrated treatment system, whose performance was examined under different operating conditions. The coupled system could achieve 92–97 % removal of soluble chemical oxygen demand (SCOD) and nearly 100 % removal of ammonia. Extending the hydraulic retention time (HRT) of the membrane photobioreactor to 3.0 days improved the production of algal biomass from 44.4 ± 23.8 to 133.7 ± 12.9 mg L^?1 (based on the volume of the treated water). When the MFCs were operated in a loop mode, their effluent (which was the influent to the algal reactor) contained nitrate and had a high pH, leading to the decreased algal production in the membrane photobioreactor. Energy analysis showed that the energy consumption was mainly due to the recirculation of the anolyte and the catholyte in the MFCs and that decreasing the recirculation rates could significantly reduce energy consumption. The energy production was dominated by indirect electricity generation from algal biomass. The highest energy production of 0.205 kWh m^?3 was obtained with the highest algal biomass production, resulting in a theoretically positive energy balance of 0.033 kWh m^?3. Those results have demonstrated that the coupled system could be an alternative approach for energy-efficient wastewater treatment and using wastewater effluent for algal production.     

Continuous electricity production from artificial wastewater using a mediator-less microbial fuel cell

A microbial fuel cell (MFC) was optimized in terms of MFC design factors and operational parameters for continuous electricity production using artificial wastewater (AW). The performance of MFC was analyzed through the polarization curve method under different conditions using a mediator-less MFC. The highest power density of 0.56 W/m2 was achieved with AW of 300 mg/l fed at the rate of 0.53 ml/min at 35 degrees C. The power per unit cell working volume was 102 mW/l, which was over 60 times higher than those reported in the previous mediator-less MFCs which did not use a cathode or an anode mediator. The power could be stably generated over 2 years.     

Electricity generation from dissolved organic matter in polluted lake water using a microbial fuel cell (MFC)

A microbial fuel cell (MFC) was explored as a pretreatment method to remove dissolved organic matter (DOM) from polluted lake water and simultaneously generate electricity. After the MFC treatment, the total organic carbon concentration in the raw lake water was reduced by 50%, the physicochemical nature of DOMs was substantially altered. Protein-like substances in lake water were utilized as a major substrate for the MFC, while humic-like substances were refractory to the biodegradation. A further investigation into the bovine serum albumin utilization in an MFC confirms that the electricity generation was closely associated with the removal of protein-like substrates. Toxicity assessment by Salmonella typhimurium Sal94 indicates that the genotoxic agents in the polluted lake water were almost completely removed after the MFC treatment. This approach of coupling microbially-catalyzed electricity generation with DOM removal may offer a potential avenue for energy-efficient bioremediation of lake water.     

Impacts of process parameters optimization on the performance of the annular single chamber microbial fuel cell in wastewater treatment

Energy harvest from optimized annular single chamber microbial fuel cell (ASCMFC) with novel configuration, which treats chocolate industry wastewater, was investigated. In this study, optimization of operational parameters of the ASCMFC in terms of efficiency water‐soluble organic matter reduction and capability of electricity generation was evaluated. During the experiment, effluent from the anode compartment was examined through current and power density curves for variation in temperature and pH, chemical oxygen demand (COD), and turbidity removal, and substrate concentration. The performance analyzed at different temperature ranges such as 25, 30, 35, and 40°C, which showed 88% increase by uprising temperature from 25 to 35°C. The ASCMFC was used to produce electricity by adjusting pH between 5 and 9 at resistance of 100 Ω. Under the condition of pH 7 power density (16.75 W/m³) was highest, which means natural pH is preferred to maximize microbial activities. Wastewater concentration with COD of 700 and 1400 mg/L were investigated to determine its affection on current production. Reduction of current density was observed due to decrease in wastewater concentration. Significant reduction in COD and turbidity of effluent were 91 and 78%, respectively. The coulombic efficiency of 45.1% was achieved.     

Simultaneous decolorization of azo dye and bioelectricity generation using a microfiltration membrane air-cathode single-chamber microbial fuel cell

Electricity generation from readily biodegradable organic substrates accompanied by decolorization of azo dye was investigated using a microfiltration membrane air-cathode single-chamber microbial fuel cell (MFC). Batch experiment results showed that accelerated decolorization of active brilliant red X-3B (ABRX3) was achieved in the MFC as compared to traditional anaerobic technology. Biodegradation was the dominant mechanism of the dye removal, and glucose was the optimal co-substrate for ABRX3 decolorization, while acetate was the worst one. Confectionery wastewater (CW) was also shown to be a good co-substrate for ABRX3 decolorization and a cheap fuel source for electricity generation in the MFC. Low resistance was more favorable for dye decolorization than high resistance. Suspended sludge (SS) should be retained in the MFC for accelerated decolorization of ABRX3. Electricity generation was not significantly affected by the ABRX3 at 300 mg/L, while higher concentrations inhibited electricity generation. However, voltage can be recovered to the original level after replacement with anodic medium not containing azo dye.     

Sustainable power production in a membrane-less and mediator-less synthetic wastewater microbial fuel cell

Microbial fuel cells (MFCs) fed with wastewater are currently considered a feasible strategy for production of renewable electricity.     

Functional stability of a hybrid anaerobic digester/microbial fuel cell system treating municipal wastewater

A thermophilic anaerobic digester (AD) was combined with a microbial fuel cell (MFC) to evaluate whether either component had increased stability when operated in combination as a hybrid system, perturbed by the addition of acetic acid. The MFC and the anaerobic digester were able to operate effectively together. The MFC was more susceptible to high acetic acid load than the AD. The hybrid system did not have increased resilience compared to the solitary systems in the conditions tested. However, the low pH had a relatively delayed effect on the MFC compared to the AD, allowing the hybrid system to have a more stable energy output. Also, at very low pH, when operating as a hybrid, the AD component was able to recover pH to normal levels when the MFC component failed. These results demonstrate that there are synergies that can be gained from this hybrid system.     

Importance of temperature and anodic medium composition on microbial fuel cell (MFC) performance

The performance of a microbial fuel cell (MFC) was investigated at different temperatures and anodic media. A lag phase of 30 h occurred at 30 degrees C which was half that at room temperature (22 degrees C). The maximum power density at 30 degrees C was 70 mW/m(2) and at 22 degrees C was 43 mW/m(2). At 15 degrees C, no successful operation was observed even after several loadings for a long period of operation. Maximum power density of 320 mW/m(2) was obtained with wastewater medium containing phosphate buffer (conductivity: 11.8 mS/cm), which was approx. 4 times higher than the value without phosphate additions (2.89 mS/cm).     

Electricity generation from model organic wastewater in a cassette-electrode microbial fuel cell

A new highly scalable microbial fuel cell (MFC) design, consisting of a series of cassette electrodes (CE), was examined for increasing power production from organic matter in wastewater. Each CE chamber was composed of a box-shaped flat cathode (two air cathodes on both sides) sandwiched in between two proton-exchange membranes and two graphite-felt anodes. Due to the simple design of the CE-MFC, multiple cassettes can be combined to form a single unit and inserted into a tank to treat wastewater. A 12-chamber CE-MFC was tested using a synthetic wastewater containing starch, peptone, and fish extract. Stable performance was obtained after 15 days of operation in fed-batch mode, with an organic removal efficiency of 95% at an organic loading rate of 2.9 kg chemical oxygen demand (COD) per cubic meter per day and an efficiency of 93% at 5.8 kg COD per cubic meter per day. Power production was stable during this period, reaching maximum power densities of 129 W m(-3) (anode volume) and 899 mW m(-2) (anode projected area). The internal resistance of CE-MFC decreased from 2.9 (day 4) to 0.64 Omega (day 25). These results demonstrate the usefulness of the CE-MFC design for energy production and organic wastewater treatment.     

Electricity generation and treatment of paper recycling wastewater using a microbial fuel cell

Increased interest in sustainable agriculture and bio-based industries requires that we find more energy-efficient methods for treating cellulose-containing wastewaters. We examined the effectiveness of simultaneous electricity production and treatment of a paper recycling plant wastewater using microbial fuel cells. Treatment efficiency was limited by wastewater conductivity. When a 50 mM phosphate buffer solution (PBS, 5.9 mS/cm) was added to the wastewater, power densities reached 501 +/- 20 mW/m(2), with a coulombic efficiency of 16 +/- 2%. There was efficient removal of soluble organic matter, with 73 +/- 1% removed based on soluble chemical oxygen demand (SCOD) and only slightly greater total removal (76 +/- 4%) based on total COD (TCOD) over a 500-h batch cycle. Cellulose was nearly completely removed (96 +/- 1%) during treatment. Further increasing the conductivity (100 mM PBS) increased power to 672 +/- 27 mW/m(2). In contrast, only 144 +/- 7 mW/m(2) was produced using an unamended wastewater (0.8 mS/cm) with TCOD, SCOD, and cellulose removals of 29 +/- 1%, 51 +/- 2%, and 16 +/- 1% (350-h batch cycle). These results demonstrate limitations to treatment efficiencies with actual wastewaters caused by solution conductivity compared to laboratory experiments under more optimal conditions.     

Electricity generation from the treatment of wastewater with a hybrid up‐flow microbial fuel cell

The performance of a prototype up‐flow single‐chambered microbial fuel cell (MFC) for electrical power generation using brewery wastewater as fuel is reported. The designed reactor consisted of three zones, namely a lower anaerobic digestion zone, a central MFC zone, and an upper effluent clarifier zone. Tests were conducted in batch mode using a beer wastewater as the fuel/electron donor (COD concentration: 430 mg/L) and mixed consortia (both sewage microflora and anaerobic sludge) as a source of electrogenic bacteria. A stable current density of ～2,270 mA/m² was generated under continuous polarization with a constant external resistance (0.01 kΩ) and cell polarization gave a peak power density of 330 mW/m² at a current density of 1,680 mA/m². Electrochemical impedance analysis showed that the overall internal resistance of the reactor was quite low, that is, 8.0 Ω. Cyclic voltammetric analysis of the anodic biofilm at low scan rate revealed quite complex processes at the anode, with three redox peaks, at potentials of 116, 214, and 319 mV (vs. NHE). Biotechnol. Bioeng. 2010;107: 52–58. © 2010 Wiley Periodicals, Inc.