Resistance of Listeria monocytogenes Biofilms to Sanitizing Agents in a Simulated Food Processing Environment

The objective of this study was to evaluate the resistance of biofilms of Listeria monocytogenes to sanitizing agents under laboratory conditions simulating a food processing environment. Biofilms were initially formed on stainless steel and Teflon coupons using a five-strain mixture of L. monocytogenes. The coupons were then subjected to repeated 24-h daily cycles. Each cycle consisted of three sequential steps: (i) a brief (60 s) exposure of the coupons to a sanitizing agent (a mixture of peroxides) or saline as a control treatment, (ii) storage of the coupons in sterile plastic tubes without any nutrients or water for 15 h, (iii) and incubation of the coupons in diluted growth medium for 8 h. This regimen was repeated daily for up to 3 weeks and was designed to represent stresses encountered by bacteria in a food processing environment. The bacteria on the coupons were reduced in number during the first week of the simulated food processing (SFP) regimen, but then adapted to the stressful conditions and increased in number. Biofilms repeatedly exposed the peroxide sanitizer in the SFP regimen developed resistance to the peroxide sanitizer as well as other sanitizers (quaternary ammonium compounds and chlorine). Interestingly, cells that were removed from the biofilms on peroxide-treated and control coupons were not significantly different in their resistance to sanitizing agents. These data suggest that the resistance of the treated biofilms to sanitizing agents may be due to attributes of extracellular polymeric substances and is not an intrinsic attribute of the cells in the biofilm.     

Resistance of Listeria monocytogenes biofilms to sanitizing agents in a simulated food processing environment

The objective of this study was to evaluate the resistance of biofilms of Listeria monocytogenes to sanitizing agents under laboratory conditions simulating a food processing environment. Biofilms were initially formed on stainless steel and Teflon coupons using a five-strain mixture of L. monocytogenes. The coupons were then subjected to repeated 24-h daily cycles. Each cycle consisted of three sequential steps: (i) a brief (60 s) exposure of the coupons to a sanitizing agent (a mixture of peroxides) or saline as a control treatment, (ii) storage of the coupons in sterile plastic tubes without any nutrients or water for 15 h, (iii) and incubation of the coupons in diluted growth medium for 8 h. This regimen was repeated daily for up to 3 weeks and was designed to represent stresses encountered by bacteria in a food processing environment. The bacteria on the coupons were reduced in number during the first week of the simulated food processing (SFP) regimen, but then adapted to the stressful conditions and increased in number. Biofilms repeatedly exposed the peroxide sanitizer in the SFP regimen developed resistance to the peroxide sanitizer as well as other sanitizers (quaternary ammonium compounds and chlorine). Interestingly, cells that were removed from the biofilms on peroxide-treated and control coupons were not significantly different in their resistance to sanitizing agents. These data suggest that the resistance of the treated biofilms to sanitizing agents may be due to attributes of extracellular polymeric substances and is not an intrinsic attribute of the cells in the biofilm.     

Differential efficacy of a chlorine dioxide-containing sanitizer against single species and binary biofilms of a dairy-associated Bacillus cereus and a Pseudomonas fluorescens isolate

AIMS: Daily exposure to 100 p.p.m. chlorine dioxide of single species and binary biofilms of dairy-associated Bacillus cereus DL5 and Pseudomonas fluorescens M2, attached to stainless steel surfaces in a laboratory flow system, was studied. METHODS AND RESULTS: Surfaces were sampled daily before and after sanitizer treatment and cells and spores dislodged and enumerated by standard methods. Duplicate surfaces were prepared for confocal scanning laser microscopy (CSLM) and scanning electron microscopy. Higher counts of Ps. fluorescens M2 were obtained in single species biofilms, microcolonies stained green (viable) in CSLM images and were closely packed on attachment surfaces. By contrast, higher counts of B. cereus DL5 were obtained in binary biofilms, microcolonies stained green in CSLM images, but were more spread out. Lower spore counts were obtained for B. cereus DL5 in binary biofilms. The survival of Ps. fluorescens M2 cells after exposure to chlorine dioxide was apparently enhanced by the presence of B. cereus DL5 in binary biofilms. By contrast, B. cereus DL5 showed increased susceptibility to sanitizer treatment in the presence of Ps. fluorescens M2. CONCLUSIONS: Co-cultured bacteria in biofilms influence each other with respect to attachment capabilities and sanitizer resistance/susceptibility. SIGNIFICANCE AND IMPACT OF THE STUDY: Binary biofilms endemic in food-processing industries can survive sanitation regimes and may represent reservoirs of product contamination leading to subsequent spoilage and/or food safety risks.     

The effect of Pseudomonas NCIMB 2021 biofilm on AISI 316 stainless steel

A bioreactor system operating in a continuous mode was designed to generate biofilms on polished and as-received surfaces of AISI 316 stainless steel coupons exposed for 36 d to a pure culture of marine Pseudomonas NCIMB 2021. Scanning electron microscopy (SEM) and atomic force microscopy were employed to determine the degree of surface colonisation and to examine corrosion damage of the steel. X-ray photoelectron spectroscopy analysis was carried out to characterise the chemistry of the passive layers on polished steel stored for a period of time, freshly re-polished coupons, and as-received steel. The effect of biofilms on the composition of layers formed on the steel specimens was evaluated. SEM revealed that the surfaces of polished and stored steel appeared to accumulate more biofilm compared to as-received specimens. Micropitting of steel occurred underneath the biofilm, regardless of surface finish. The concentration of elements in the passive layers differed significantly between freshly re-polished and as-received or polished and stored coupons. In the presence of Pseudomonas NCIMB 2021 biofilm, the composition of the passive layer on the as-received steel surface was considerably altered compared to unexposed steel or steel exposed to abiotic medium.     

The effects of disinfectant foam on microbial biofilms

This investigation examined the effects of common aqueous biocides and disinfectant foams derived from them on Pseudomonas aeruginosa biofilms. Biofilms were grown on stainless steel coupons under standardised conditions in a reactor supplemented with low concentrations of organic matter to simulate conditions prevalent in industrial systems. Five-day-old biofilms formed under ambient conditions with continuous agitation demonstrated a low coefficient of variation (5.809%) amongst viable biofilm bacteria from independent trials. Scanning electron microscopy revealed biofilms on coupons with viable biofilm bacteria observed by confocal microscopy. An aqueous solution of a common foaming agent amine oxide (AO) produced negligible effects on bacterial viability in biofilms (p>0.05). However, significant biofilm inactivation was noted with aqueous solutions of common biocides (peracetic acid, sodium hypochlorite, sodium ethylenediaminetetraacetic acid) with or without AO (p<0.05). Aereation of a mixture of AO with each of these common biocides resulted in significant reductions in the viability of biofilm bacteria (p<0.05). In contrast, limited effects were noted by foam devoid of biocides. A relationship between microbial inactivation and the concentration of biocide in foam (ranging from 0.1-0.5%) and exposure period were noted (p<0.05). Although, lower numbers of viable biofilm bacteria were recovered after treatment with the disinfectant foam than by the cognate aqueous biocide, significant differences between these treatments were not evident (p>0.05). In summary, the studies revealed significant biofilm inactivation by biocidal foam prepared with common biocides. Validation of foam disinfectants in controlled trials at manufacturing sites may facilitate developments for clean in place applications. Advantages of foam disinfectants include reductions in the volumes of biocides for industrial disinfection and in their disposal after use.     

Inactivation of Escherichia coli O157:H7 in biofilm on stainless steel by treatment with an alkaline cleaner and a bacteriophage

AIMS: To determine the effectiveness of an alkaline cleaner used in food-processing plants and a lytic bacteriophage specific for Escherichia coli O157:H7 in killing wild type and rpoS-deficient cells of the pathogen in a biofilm. METHODS AND RESULTS: Wild type and rpoS-deficient cells were attached to stainless steel coupons (c. 7-8 log CFU per coupon) on which biofilms were developed during incubation at 22 degrees C for 96 h in M9 minimal salts media (MSM) with one transfer to fresh medium. Coupons were treated with 100 and 25% working concentrations of a commercial alkaline cleaner (pH 11.9, with 100 microg ml(-1) free chlorine) used in the food industry, chlorine solutions (50 and 100 microg ml(-1) free chlorine), or sterile deionized water (control) at 4 degrees C for 1 and 3 min. Treatment with 100% alkaline cleaners reduced populations by 5-6 log CFU per coupon, a significant (P < or = 0.05) reduction compared with treatment with water. Initial populations (2.6 log CFU per coupon) of attached cells of both strains were reduced by 1.2 log CFU per coupon when treated with bacteriophage KH1 (7.7 log PFU ml(-1)) for up to 4 days at 4 degrees C. Biofilms containing low populations (2.7-2.8 log CFU per coupon) of wild type and rpoS-deficient cells that had developed for 24 h at 22 degrees C were not decreased by more than 1 log CFU per coupon when treated with KH1 (7.5 log PFU ml(-1)) at 4 degrees C. CONCLUSIONS: Higher numbers of cells of E. coli O157:H7 in biofilms are killed by treatment with an alkaline cleaner than with hypochlorite alone, possibly through a synergistic mechanism of alkaline pH and hypochlorite. Populations of cells attached on coupons were reduced by treating with bacteriophage but cells enmeshed in biofilms were protected. SIGNIFICANCE AND IMPACT OF THE STUDY: The alkaline pH, in combination with hypochlorite, in a commercial cleaner is responsible for killing E. coli O157:H7 in biofilms. Treatment with bacteriophage KH1 reduces populations of cells attached to coupon surfaces but not cells in biofilms.     

Attachment and biofilm formation on stainless steel by Escherichia coli O157:H7 as affected by curli production

AIMS: The aim of this study was to determine the role of curli in attachment and biofilm formation by Escherichia coli O157:H7 on stainless steel. METHODS AND RESULTS: Three curli-deficient strains (43895-, 43894- and E0018-) and three curli over-producing strains (43895+, 43894+ and E0018+) of E. coli O157:H7 were studied. Stainless steel coupons (SSC) were immersed in cell suspensions of each strain for 24 h at 4 degrees C. The number of cells attached to SSC was determined. To determine the ability of attached cells to form biofilm, SSC were immersed in 10% of tryptic soya broth up to 6 days at 22 degrees C. Curli-deficient and curli-producing strains did not differ in their ability to attach to SSC, but only curli-producing strains formed biofilms. CONCLUSIONS: Curli production by E. coli O157:H7 does not affect attachment of cells on stainless steel but curli-producing strains are better able to form biofilms. SIGNIFICANCE AND IMPACT OF THE STUDY: Curli production by E. coli O157:H7 enhances its ability to form biofilm on stainless steel, thereby potentially resulting in increased difficulty in removing or killing cells by routine cleaning and sanitizing procedures used in food-processing plants.     

Studies on the behaviour of Pseudomonas fluorescens biofilms after Ortho-phthalaldehyde treatment

A relatively novel biocide, ortho-phthalaldehyde (OPA), was tested to control biofilms formed by Pseudomonas fluorescens on stainless steel surfaces. The toxic action of OPA was assessed in terms of inactivation and removal of the biofilm by means of, respectively, the determination of the respiratory activity and the variation in the dry weight of the biofilms. For comparison, the activity of OPA against suspended bacteria was also evaluated. The results showed that higher concentrations of OPA and longer exposure times are needed to inactivate P. fluorescens biofilms than planktonic populations, thus denoting that sessile bacteria have a reduced susceptibility to OPA. This appears to be associated with the reaction with the proteins of the matrix, as demonstrated by the reduction of the antimicrobial action of OPA in the presence of a protein (bovine serum albumin). The application of OPA appeared to cause little effect in the removal of biofilms from the metal slides since the mass of biofilm that remained on the surfaces, after biocide treatment, was within the same range as those observed in the control tests. These results suggest that, with OPA application, biofilms can be inactivated but stay attached to the surfaces, decreasing thereby the success of the chemical treatment.     

The differential adherence capabilities of two Listeria monocytogenes strains in monoculture and multispecies biofilms as a function of temperature

AIMS: To determine the differential adherence capabilities at three different temperatures of Listeria monocytogenes Scott A, a clinical food pathogen, and L. monocytogenes FM876, a persistent strain from a milk-processing environment, to stainless steel. METHODS AND RESULTS: Differential adherence was investigated by submerging stainless steel coupons in both 48-h Listeria monocultures and mixed cultures additionally containing Staphylococcus xylosus DP5H and Pseudomonas fragi ATCC 4973. Immunofluorescent microscopy and image analysis techniques were utilized to identify and quantify the L. monocytogenes cells adhering to the steel at 4 degrees C, 18 degrees C and 30 degrees C. The monoculture biofilms consistently contained greater L. monocytogenes numbers than the multispecies biofilms, with the persistent strain FM876 showing significantly greater adherence than strain Scott A. Optimum adherence occurred at 18 degrees C in monoculture biofilms. CONCLUSION: L. monocytogenes strains exhibit differential, temperature-dependent, adherence to stainless steel. SIGNIFICANCE AND IMPACT OF THE STUDY: These results demonstrate temperature dependent biofilm adherence and support previous findings that persistent strains exhibit increased adherence capability.     

Effects of marine paints on microbial biofilm development on three materials

The development of biofilms of Pseudomonas aeruginosa PAO-1 was studied using modified Robbins devices. Biofilm development was measured using viable counts, acridine orange direct counts (AODC), and a colorimetric method for exopolysaccharide (EPS). Biofilms reached their maximum population 24–72 h after inoculation on coupons with no paint or on coupons coated with marine paint VC-18 without additives. Biofilms on stainless steel contained higher numbers of total cells and of viable cells than biofilms on fiberglass or aluminum. Coating the surfaces with marine paint VC-18 resulted in decreased numbers of cells on stainless steel but had little effect on numbers of cells on fiberglass or aluminum. Addition to the paint of Cu or tributyltin (TBT), the active components in two types of antifouling paints, inhibited the initial development of biofilms. However, by 72–96 h, most biofilms contained the same number of cells as surfaces without additives as shown by both viable counts and AODC. Biofilms that formed on surfaces coated with Cu- or TBT-containing paint did not synthesize more EPS, suggesting that P. aeruginosa PAO-1 does not respond to these compounds by synthesizing more EPS, which could bind the metal and protect the cells. Rather, these biofilms may contain Cu- or TBT-resistant cells. TBT-resistant cells made up 1–10% of the viable counts in biofilms on uncoated stainless steel, but in biofilms on stainless steel coated with marine paint containing TBT, TBT-resistant cells made up as much as 50% of the population. For non-coated stainless steel surfaces, Cu-resistant cells initially made up the majority of the population, but after 48 h they made up less than 1% of the population. On Cu-coated stainless steel, Cu-resistant cells predominated through 48 h, but after 48 h they comprised less than 10% of the population. These results suggest that the growth of TBT-resistant and Cu-resistant cells contributes to biofilms of P. aeruginosa PAO-1 at early stages of development but not at later stages. Received 16 December 1997/ Accepted in revised form 9 March 1998     

The effects of disinfectant foam on microbial biofilms

This investigation examined the effects of common aqueous biocides and disinfectant foams derived from them on Pseudomonas aeruginosa biofilms. Biofilms were grown on stainless steel coupons under standardised conditions in a reactor supplemented with low concentrations of organic matter to simulate conditions prevalent in industrial systems. Five-day-old biofilms formed under ambient conditions with continuous agitation demonstrated a low coefficient of variation (5.809%) amongst viable biofilm bacteria from independent trials. Scanning electron microscopy revealed biofilms on coupons with viable biofilm bacteria observed by confocal microscopy. An aqueous solution of a common foaming agent amine oxide (AO) produced negligible effects on bacterial viability in biofilms (p?>?0.05). However, significant biofilm inactivation was noted with aqueous solutions of common biocides (peracetic acid, sodium hypochlorite, sodium ethylenediaminetetraacetic acid) with or without AO (p?<?0.05). Aereation of a mixture of AO with each of these common biocides resulted in significant reductions in the viability of biofilm bacteria (p?<?0.05). In contrast, limited effects were noted by foam devoid of biocides. A relationship between microbial inactivation and the concentration of biocide in foam (ranging from 0.1?–?0.5%) and exposure period were noted (p?<?0.05). Although, lower numbers of viable biofilm bacteria were recovered after treatment with the disinfectant foam than by the cognate aqueous biocide, significant differences between these treatments were not evident (p?>?0.05). In summary, the studies revealed significant biofilm inactivation by biocidal foam prepared with common biocides. Validation of foam disinfectants in controlled trials at manufacturing sites may facilitate developments for clean in place applications. Advantages of foam disinfectants include reductions in the volumes of biocides for industrial disinfection and in their disposal after use.     

The galactophilic lectin, LecA, contributes to biofilm development in Pseudomonas aeruginosa

LecA (PA-IL) is a cytotoxic lectin and adhesin produced by Pseudomonas aeruginosa which binds hydrophobic galactosides with high specificity and affinity. By using a lecA-egfp translation fusion and immunoblot analysis of the biofilm extracellular matrix, we show that lecA is expressed in biofilm-grown cells. In static biofilm assays on both polystyrene and stainless steel, biofilm depth and surface coverage was reduced by mutation of lecA and enhanced in the LecA-overproducing strain PAO-P47. Biofilm surface coverage by the parent strain, PAO-P47 but not the lecA mutant on steel coupons was also inhibited by growth in the presence of either isopropyl-beta-D-thiogalactoside (IPTG) or p-nitrophenyl-alpha-D-galactoside (NPG). Furthermore, mature wild-type biofilms formed in the absence of these hydrophobic galactosides could be dispersed by the addition of IPTG. In contrast, addition of p-nitrophenyl-alpha-L-fucose (NPF) which has a high affinity for the P. aeruginosa LecB (PA-IIL) lectin had no effect on biofilm formation or dispersal. Planktonic growth of P. aeruginosa PAO1 was unaffected by the presence of IPTG, NPG or NPF, nor was the strain able to utilize these sugars as carbon sources, suggesting that the observed effects on biofilm formation were due to the competitive inhibition of LecA-ligand binding. Similar results were also obtained for biofilms grown under dynamic flow conditions on steel coupons, suggesting that LecA contributes to P. aeruginosa biofilm architecture under different environmental conditions.     

Role of beta 1-4 linked polymers in the biofilm structure of marine Pseudomonas sp. CE-2 on 304 stainless steel coupons

Pseudomonas sp CE-2 cells attach and form biofilms on 304-stainless steel (SS) coupons. A series of experiments were carried out in order to understand the role of exopolysaccharides (EPS) in the formation and maintenance of CE-2 biofilms on SS coupons. The biofilm density and EPS concentration increased over the period of incubation and the highest values for both were recorded after 72 h. Calcofluor and the lectin concanavalin A (Con A) showed a positive interaction with 72-h old biofilms, indicating the presence of beta 1-4 linked polymers, and alpha-d-glucose and alpha-d-mannose in the biofilm matrix of CE-2. When the CE-2 cells were grown in the presence of calcofluor (200 microg ml(-1)), biofilm formation was significantly reduced (approximately 85%). Conversely, the lectins Con A or WGA did not influence the CE-2 biofilms on the SS coupons. Furthermore, treatment with cellulase, an enzyme specific for the degradation of beta 1-4 linked polymers, removed substantial amounts of CE-2 biofilm from SS coupons. These results strongly suggest the involvement of beta 1-4 linked polymers in the formation and maintenance of Pseudomonas sp. CE-2 biofilms on SS coupons.     

The effects of glutaraldehyde on the control of single and dual biofilms of Bacillus cereus and Pseudomonas fluorescens

Glutaraldehyde (GLUT) was evaluated for control of single and dual species biofilms of Bacillus cereus and Pseudomonas fluorescens on stainless steel surfaces using a chemostat system. The biofilms were characterized in terms of mass, cell density, total and matrix proteins and polysaccharides. The control action of GLUT was assessed in terms of inactivation and removal of biofilm. Post-biocide action was characterized 3, 7, 12, 24, 48 and 72 h after treatment. Tests with planktonic cells were also performed for comparison. The results demonstrated that in dual species biofilms the metabolic activity, cell density and the content of matrix proteins were higher than those of either single species. Planktonic B. cereus was more susceptible to GLUT than P. fluorescens. The biocide susceptibility of dual species planktonic cultures was an average of each single species. Planktonic cells were more susceptible to GLUT than their biofilm counterparts. Biofilm inactivation was similar for both of the single biofilms while dual biofilms were more resistant than single species biofilms. GLUT at 200 mg l(-1) caused low biofilm removal (<10%). Analysis of the post-biocide treatment data revealed the ability of biofilms to recover their activity over time. However, 12 h after biocide application, sloughing events were detected for both single and dual species biofilms, but were more marked for those formed by P. fluorescens (removal >40% of the total biofilm). The overall results suggest that GLUT exerts significant antimicrobial activity against planktonic bacteria and a partial and reversible activity against B. cereus and P. fluorescens single and dual species biofilms. The biocide had low antifouling effects when analysed immediately after treatment. However, GLUT had significant long-term effects on biofilm removal, inducing significant sloughing events (recovery in terms of mass 72 h after treatment for single biofilms and 42 h later for dual biofilms). In general, dual species biofilms demonstrated higher resistance and resilience to GLUT exposure than either of the single species biofilms. P. fluorescens biofilms were more susceptible to the biocide than B. cereus biofilms.     

Metal corrosion by aerobic bacteria isolated from stimulated corrosion systems: Effects of additional nitrate sources

Many microorganisms are reported to influence the corrosive behaviour of mild steel and stainless steel in different habitats. In this study, 40 bacterial strains were isolated from corroded mild steel and stainless steel coupons in the nitrate supplemented environments. The corrosion abilities of the isolates against the mild steel and stainless steel coupons were tested with or without additional nitrate sources. The presence of bacterial isolates alone stimulated the corrosion of mild steel coupons. Most of the bio-corrosion processes of mild steel coupons were mitigated by adding nitrate supplement with bacterial isolates. The effects of bacterial isolates and additional nitrogen sources on corrosion of stainless steels were varied. Not all bacterial isolates stimulated the corrosion on stainless steel during the study period. Unlike the effects on mild steel coupons, additional NaNO₃ might stimulate, retard the corrosion rate by the bacterial isolates or have limited effects. Similar results were obtained when NH₄NO₃ was used. Phylogenetic analysis demonstrated that all isolates were closely related. The majority of the bacterial isolates from corroded metal coupons were identified as Bacillus species. Others were identified as Pseudomonas sp., Marinobacter sp., and Halomonas species. The results prove that the isolated aerobic microorganisms do play a role in the corrosion process of stainless and mild steel. Adding additional nitrate sources might be a tool to mitigate corrosion of mild steel which was stimulated by the presence of bacteria. However, to prevent the corrosion of stainless steels, it might need a trial and errors approach in each case.     

Sodium dodecyl sulfate allows the persistence and recovery of biofilms of Pseudomonas fluorescens formed under different hydrodynamic conditions

The effect of the anionic surfactant sodium dodecyl sulfate (SDS) on Pseudomonas fluorescens biofilms was investigated using flow cell reactors with stainless steel substrata, under turbulent (Re = 5200) and laminar (Re = 2000) flow. Steady-state biofilms were exposed to SDS in single doses (0.5, 1, 3 and 7 mM) and biofilm respiratory activity and mass measured at 0, 3, 7 and 12 h after the SDS application. The effect of SDS on biofilm mechanical stability was assessed using a rotating bioreactor. Whilst high concentrations (7 mM) of SDS promoted significant biofilm inactivation, it did not significantly reduce biofouling. Turbulent and laminar flow-generated biofilms had comparable susceptibility to SDS application. Following SDS exposure, biofilms rapidly recovered over the following 12 h, achieving higher respiratory activity values than before treatment. This phenomenon of post-treatment recovery was more pronounced for turbulent flow-generated biofilms, with an increase in SDS concentration. The mechanical stability of the biofilms increased with surfactant application, except for SDS concentrations near the critical micellar concentration, as measured by biofilm removal due to an increase in external shear stress forces. The data suggest that although SDS exerts antimicrobial action against P. fluorescens biofilms, even if only partial and reversible, it had only limited antifouling efficacy, increasing biofilm mechanical stability at low concentrations and allowing significant and rapid recovery of turbulent flow-generated biofilms.     

Inactivation of Escherichia coli, Listeria monocytogenes, Pseudomonas aeruginosa and Staphylococcus aureus on stainless steel and glass surfaces by neutral electrolysed water

AIM: To ascertain the efficacy of neutral electrolysed water (NEW) in reducing Escherichia coli, Pseudomonas aeruginosa, Staphylococcus aureus and Listeria monocytogenes on glass and stainless steel surfaces. Its effectiveness for that purpose is compared with that of a sodium hypochlorite (NaClO) solution with similar pH, oxidation-reduction potential (ORP) and active chlorine content. METHODS AND RESULTS: First, the bactericidal activity of NEW was evaluated over pure cultures (8.5 log CFU ml-1) of the abovementioned strains: all of them were reduced by more than 7 log CFU ml-1 within 5 min of exposure either to NEW (63 mg l-1 active chlorine) or to NaClO solution (62 mg l-1 active chlorine). Then, stainless steel and glass surfaces were inoculated with the same strains and rinsed for 1 min in either NEW, NaClO solution or deionized water (control). In the first two cases, the populations of all the strains decreased by more than 6 log CFU 50 cm-2. No significant difference (P相似文献   

Extracellular polysaccharides from Desulfovibrio desulfuricans and Pseudomonas fluorescens in the presence of mild and stainless steel

Summary This communication reports the presence of polysaccharides in biofilms formed by pure and mixed cultures of Desulfovibrio desulfuricans and Pseudomonas fluorescens on mild and stainless steel surfaces. The results of colorimetric assays, indicating significant differences between the amounts of neutral sugars present in these biofilms, were supported by gas chromatographic (GC)-mass spectrophotometric and GC-flame ionisation detection analyses. Neutral sugars in biofilms grown on mild steel surfaces were identified and quantified, revealing glucose as a major carbohydrate followed by mannose and galactose in all types of biofilm. Extracellular polymeric substances (EPS) precipitated from bacterial cultures grown with and without steel surfaces were also analysed for their carbohydrate content. The influence of the surfaces present in the cultures on the amount and type of sugars released into the bulk phase was established. There was significantly more carbohydrate in EPS harvested from pure and mixed cultures of D. desulfuricans incubated mild and stainless steel coupons than in EPS obtained from coupon-free cultures. No significant difference in sugar quantities was observed in EPS precipitated from cultures of P. fluorescens grown under different conditions (absence or presence of steel surfaces). The main carbohydrates identified in all types of EPS samples were mannose, glucose and galactose in order of prevalence. Offprint requests to: I. B. Beech     

Inactivation of Escherichia coli and Listeria monocytogenes on iceberg lettuce by dip wash treatments with organic acids

AIMS: To study and compare the efficacy of organic acids and chlorine dipping in inactivation of Escherichia coli and Listeria monocytogenes on fresh-cut iceberg lettuce. METHODS AND RESULTS: Fresh-cut iceberg lettuce leaves were inoculated with E. coli or L. monocytogenes. After inoculation, samples were stored at 4 degrees C for 24 h and dipped in organic acid or chlorine solutions for 2 and 5 min. E. coli and L. monocytogenes were enumerated on selective media. Treatment of fresh-cut iceberg lettuce with chlorine solution caused 1.0 and 2.0 log(10) CFU g(-1) reductions in the number of L. monocytogenes and E. coli, respectively. Maximum reduction for E. coli (about 2.0 log(10) CFU g(-1)) was obtained for samples dipped in lactic or citric acids while maximum reduction for L. monocytogenes (about 1.5 log(10) CFU g(-1)) was attained for samples dipped in lactic acid. CONCLUSIONS: Dipping of iceberg lettuce in 0.5% citric acid or 0.5% lactic acid solution for 2 min could be as effective as chlorine for reducing microbial populations on fresh-cut iceberg lettuce. SIGNIFICANCE AND IMPACT OF THE STUDY: Dipping in solutions containing organic acids is shown to be effective to reduce E. coli and L. monocytogenes on fresh-cut iceberg lettuce.     

Biofilm formation and cellulose expression among diverse environmental Pseudomonas isolates

The ability to form biofilms is seen as an increasingly important colonization strategy among both pathogenic and environmental bacteria. A survey of 185 plant-associated, phytopathogenic, soil and river Pseudomonas isolates resulted in 76% producing biofilms at the air-liquid (A-L) interface after selection in static microcosms. Considerable variation in biofilm phenotype was observed, including waxy aggregations, viscous and floccular masses, and physically cohesive biofilms with continuously varying strengths over 1500-fold. Calcofluor epifluorescent microscopy identified cellulose as the matrix component in biofilms produced by Pseudomonas asplenii, Pseudomonas corrugata, Pseudomonas fluorescens, Pseudomonas marginalis, Pseudomonas putida, Pseudomonas savastanoi and Pseudomonas syringae isolates. Cellulose expression and biofilm formation could be induced by the constitutively active WspR19 mutant of the cyclic-di-GMP-associated, GGDEF domain-containing response regulator involved in the P. fluorescens SBW25 wrinkly spreader phenotype and cellular aggregation in Pseudomonas aeruginosa PA01. WspR19 could also induce P. putida KT2440, which otherwise did not produce a biofilm or express cellulose, as well as Escherichia coli K12 and Salmonella typhimurium LT2, both of which express cellulose yet lack WspR homologues. Statistical analysis of biofilm parameters suggest that biofilm development is a more complex process than that simply described by the production of attachment and matrix components and bacterial growth. This complexity was also seen in multivariate analysis as a species-ecological habitat effect, underscoring the fact that in vitro biofilms are abstractions of those surface and volume colonization processes used by bacteria in their natural environments.