The use of the tetrazolium salt XTT for the estimation of biological activity of activated sludge cultivated under steady-state and transient regimes

The tetrazolium salt 3′-{1-[(phenylamino)-carbonyl]-3,4-tetrazolium}-bis (4-methoxy-6-nitro) benzenesulfonic acid hydrate (XTT) was used as a tool for estimating the activity of the electron transport system (ETS) in activated sludge cultivated under steady-state and transient regimes in chemostat culture. Production of formazan by reduction of XTT depended on the initial concentration of the XTT following a saturation law and was proportional to live cell biomass. Addition of cyanide (KCN) to activated sludge gave an initial 1.5-fold increase in XTT reduction, while addition of 3,5-dichlorophenol (3,5-DCP) reduced this value drastically. At steady-state and transient regimes of an activated sludge chemostat, oxygen uptake rate (OUR) and XTT reduction rate were highly correlated and indicated significant variations depending on the growth conditions.     

Using acoustic cavitation to improve the bio-activity of activated sludge

This paper studied a new method to improve the microbial activity of the activated sludge for wastewater treatment. Concentrated sludge was sonicated in an extra chamber for short period and then returned to the activated sludge system. The results showed that the bio-activity of the activated sludge, expressed as oxygen utilization rate (OUR), could be enhanced by ultrasonic irradiation. Powerful ultrasound (in the magnitude of W/ml) was much more effective than weak ultrasound (in the magnitude of W/L) in stimulating the activated sludge, but too strong sonication (power density higher than 0.5 W/ml) disintegrated the sludge and thus decreased the sludge activity. Low frequency (25 kHz) was more effective than higher ones (80 kHz and 150 kHz), indicating that mechanical effects, instead of free radicals, were responsible for the bio-activity enhancement. The optimal sonication conditions were sound frequency of 25 kHz, power density of 0.2 W/ml and duration of 30s; under which the sludge OUR increased by 28%, the bio-mass growth rate increased by 12.5%, and the wastewater chemical oxygen demand (COD) and total nitrogen removal efficiency increased by 5-6%.     

Optimization and/or acclimatization of activated sludge process under heavy metals stress

The present study aimed to overcome the toxicity of the heavy metals load, discharged with the industrial effluents into Alexandria sewerage network, on the activated sludge treatment system through effective acclimation for organic matter and heavy metals removal. Optimization and/or acclimatization of the activated sludge process in the presence of Cu, Cd, Co and Cr contaminating mixed domestic-industrial wastewater was investigated. Acclimatization process was performed through abrupt and stepwise addition of tested metals using sequencing batch reactors treatment approach and evaluated as microbial oxygen uptake rate (OUR), dehydrogenase activity (DHA), organic matter (COD) and heavy metals removal. Abrupt addition of metals adversely affected sludge bioactivity leading to decline in the removal efficiency of the targeted contaminants and loss of floc structure. Metals IC₅₀ confirmed that copper possessed the highest toxicity towards the OUR, DHA activity and COD removal with orders Cu > Cd > Cr > Co; Cu > Cd > Co = Cr and Cu > Cd > Cr > Co, respectively. The highest metal removal was recorded for Cd followed by Co, Cu and finally Cr, most of which was retained in the dissolved influent. However, controlled stepwise application of the tested metals exhibited high sensitivity of DHA and OUR activities only at the highest metal concentrations although enhanced at the lowest concentrations while COD removal was not significantly affected. In conclusion, this approach resulted in adaptation of the system where sludge microbes acquired and developed natural resistance to such metals leading to remarkable enhancement of both organic matter and heavy metals removal.     

Predicting the effects of chlorine on the micro-organisms of filamentous bulking activated sludges

Rapid and definite assessment of the effect that a specific biocide has on a specific case of filamentous bulking sludge is a much-needed tool in activated sludge wastewater treatment. The Live/Dead stain (LIVE/DEAD BacLight) distinguishing "living" and "non-living" cells, a nitrifying activity (NA) test and the oxygen uptake rate (OUR) measurement were examined for their appropriateness to predict the effects of chlorine on filamentous bulking sludges. The study showed the live/dead stain to be relevant for revealing the specific effect of chlorine on the filamentous bacteria of a bulking sludge. However, using live/dead stain alone for the determination of the appropriate chlorine dose against bulking may lead to an underestimation of the damage caused by chlorine to the useful microorganisms in the flocs. Indeed, using the live/dead stain, it was not easy to distinguish dead cells caused by chlorination from those originally present in the flocs The NA test was the most sensitive in detecting damage caused by chlorine to the floc-forming microorganisms. Therefore, for a safer determination of the chlorine dose effective against bulking and protective of the microbial activity of the sludge, the results of this study suggest coupling of the live/dead stain with the NA test and/or the OUR test.     

Study of Biological Activity and Process Stability in Submerged Membrane Bioreactors

Synthetic wastewater was treated in a bench scale submerged membrane bioreactor (SMBR). A long‐term experiment was conducted by varying the sludge residence time (SRT) (10–500 d) and BOD loading (1.3–0.25 kg/m³·d). The biological activity was observed in terms of the oxygen utilization rate (OUR) and adenosine triphosphate (ATP) profile; the process stability was analyzed based on the extent of organic degradation and suction pressure. The microbial population in the SMBR was dependent on the SRT and BOD loading, and its biological activity was increased with an increase in the SRT or BOD loading. At a low feed to microorganism (F/M) ratio (0.06 kg BOD/kg MLSS·d), the sludge production of the reactor was reduced to 0.04 kg MLSS/kg BOD, which is much less than in the conventional activated sludge process (0.4–0.6 kg MLSS/kg BOD). The F/M ratio influenced the biological activity (via ATP and the OUR) significantly at a short SRT (≤90 d). However, the effect of the F/M ratio ceased at a low F/M ratio (≤ 0.07 kg BOD/kg MLSS·d). The accumulation of organics in the SMBR was accompanied with an increase in the supernatant TOC, which caused a high suction pressure and an abrupt change in the operating conditions to process instability. However, the process stability of the SMBR increased with an increase in the SRT and a decrease in the BOD loading along with a concomitant decrease in the biological activity and sludge production.     

Effect of pH and nitrite concentration on nitrite oxidation rate

The effect of pH and nitrite concentration on the activity of the nitrite oxidizing bacteria (NOB) in an activated sludge reactor has been determined by means of laboratory batch experiments based on respirometric techniques. The bacterial activity was measured at different pH and at different total nitrite concentrations (TNO?). The experimental results showed that the nitrite oxidation rate (NOR) depends on the TNO? concentration independently of the free nitrous acid (FNA) concentration, so FNA cannot be considered as the real substrate for NOB. NOB were strongly affected by low pH values (no activity was detected at pH 6.5) but no inhibition was observed at high pH values (activity was nearly the same for the pH range 7.5-9.95). A kinetic expression for nitrite oxidation process including switch functions to model the effect of TNO? concentration and pH inhibition is proposed. Substrate half saturation constant and pH inhibition constants have been obtained.     

Modelling and dynamic simulation of a moving bed bioreactor using respirometry for the estimation of kinetic parameters

Respirometry was used for the characterization of active autotrophic and heterotrophic biomass in a pilot scale moving bed bioreactor (MBBR). For this purpose biofilm samples attached to the carrier elements of the MBBR were transferred to a static gas/static liquid type respirometer with intermittent aeration. Known amounts of ammonia nitrogen and acetate were added to the respirometer. The dissolved oxygen (DO) decrease during the non-aeration phase was measured and used to calculate the oxygen uptake rate (OUR) of the active biomass. The resulting respirograms featured the typical endogenous and exogenous respiration phases and the shape of the respirogram was as expected from analogous respirometry with activated sludge. The OUR response was modelled with the activated sludge model ASM1 and the relevant kinetic parameter values for autotrophic and heterotrophic growth were adjusted. The adjusted parameter set and data originating from a 4-day long intensive measurement campaign were used for modelling and simulation of the pilot scale MBBR. The parameter estimation resulted in a good dynamic simulation of ammonia and nitrate variations in the effluent of the MBBR. Important MBBR properties including biofilm age, biofilm composition, and both attachment and detachment rate were extracted from the model.     

Assay of succinate dehydrogenase activity by the tetrazolium method: evaluation of an improved technique in skeletal muscle fractions

An improved spectrophotometric method for measuring succinate dehydrogenase (EC 1.3.99.1) activity with the use of 2-(p-iodophenyl)-3-(p-nitrophenyl)-5-phenyltetrazolium chloride (INT) is described. The procedure has been evaluated in mitochondrial fractions and homogenates of frog skeletal muscle. For mitochondrial suspensions, extraction of formazan with alcohol was found to be superior to extraction with ethyl acetate. For homogenates, complete extraction of formazan required sequential treatment with alcohol and ethyl acetate; the generally employed procedure of extracting once with ethyl acetate alone led to serious underestimation of the amount of formazan in the tissue. Observations of mitochondrial suspension incubated with various concentrations of INT led to the selection of 0.8 mM INT for optimal results. Higher concentrations, although commonly used, can exert undesirable inhibitory effects on succinate dehydrogenase activity, especially at low concentrations of mitochondria and after longer periods of incubation. The problem of instability of succinate dehydrogenase was solved by the addition of buffer at pH 7.5.     

Malachite green-INT (MINT) method for determining active bacteria in sewage.

A membrane filtration method was developed to determine the proportion of active (respiring) bacteria at various stages of sewage treatment. Samples were incubated in the presence of 2-(p-iodophenyl)-3-(p-nitrophenyl)-5-phenyl tetrazolium chloride (INT) and, after fixation, passed through membrane filters. Filters were counterstained with malachite green and then were examined by bright-field microscopy. The contrast between bacteria and the filter background was greatly improved by drying and then clearing the filter before counterstaining. By this method, it was found that active bacterial fractions in raw sewage, settled sewage, and secondary effluent were 40, 29, and 58%, respectively, whereas the proportion of respiring bacteria in chlorinated secondary effluent was 6.1%. The active bacterial fraction of activated sludge was found to be 16%. The proposed method represents a significant improvement in speed and simplicity over existing methods for determining active bacteria in sewage.     

Exploration of the diaphorase activity of neutrophil NADPH oxidase.

In the O2- generating flavocytochrome b, the membrane-bound component of the neutrophil NADPH oxidase, electrons are transported from NADPH to O2 in the following sequence: NADPH --> FAD --> heme b -->O2. Although p-iodonitrotetrazolium (INT) has frequently been used as a probe of the diaphorase activity of the neutrophil flavocytochrome b, the propensity of its radical to interact reversibly with O2 led us to question its specificity. This study was undertaken to reexamine the interaction of INT with the redox components of the neutrophil flavocytochrome b. Two series of inhibitors were used, namely the flavin analog 5-deaza FAD and the heme inhibitors bipyridyl and benzylimidazole. The following results indicate that INT reacts preferentially with the hemes rather than with the FAD redox center of flavocytochrome b and is not therefore a specific probe of the diaphorase activity of flavocytochrome b. First, in anaerobiosis, reduced heme b in activated membranes was reoxidized by INT as efficiently as by O2 even in the presence of concentrations of 5-deaza FAD which fully inhibited the NADPH oxidase activity. Second, the titration curve of dithionite-reduced heme b in neutrophil membranes obtained by oxidation with increasing amounts of INT was strictly superimposable on that of dithionite-reduced hemin. Third, INT competitively inhibited the O2 uptake by the activated NADPH oxidase in a cell-free system. Finally, the heme inhibitor bipyridyl competitively inhibited the reduction of INT in anaerobiosis, and the oxygen uptake in aerobiosis.     

Effects of oxygen exposure on respiratory activities of Desulfovibrio desulfuricans strain DvO1 isolated from activated sludge

The present study addresses the effects of oxygen exposure on the aerobic and anaerobic respiratory activity of Desulfovibrio desulfuricans strain DvO1. This strain was isolated from the highest sulfate-reduction positive most-probable-number dilution (10(6)) of an activated sludge sample, which had been subjected to 120 h of continuous aeration. Washed cell suspensions of strain DvO1 were aerated at 50% atmospheric oxygen saturation in sulfide-free media for a period of 33 h in the presence or absence of an external electron donor (10 mM lactate). During the aeration periods, samples were removed at intervals for determination of anaerobic INT [2-(p-iodophenyl)-3-(p-nitrophenyl)-5-phenyl tetrazolium chloride]-reducing activity, anaerobic sulfate-reducing activity, and oxygen-reducing activity. The cell suspension aerated in the absence of lactate showed negligible endogenous oxygen reduction rates and therefore did not consume oxygen during the aeration period. In contrast, the cell suspension aerated in the presence of lactate sustained significant rates of oxygen reduction during the entire 33 h aeration period. Despite this, no explicit differences in the potential INT-, oxygen-, or sulfate-reducing activities were evident between the two cell suspensions during the aeration periods. Strain DvO1 remained viable throughout the 33 h aeration periods irrespective of the presence or absence of lactate, however, the oxygen exposure resulted in a dose-dependent reversible metabolic inactivation. Notably, lactate-dependent anaerobic sulfate-reducing activity recovered quickly upon anaerobiosis, and was more oxygen tolerant than lactate-dependent oxygen-reducing activity.     

Entomotoxicity,protease and chitinase activity of Bacillus thuringiensis fermented wastewater sludge with a high solids content

This study investigated the production of biopesticides, protease and chitinase activity by Bacillus thuringiensis grown in raw wastewater sludge at high solids concentration (30 g/L). The rheology of wastewater sludge was modified with addition of Tween-80 (0.2% v/v). This addition resulted in 1.6 and 1.3-fold increase in cell and spore count, respectively. The maximum specific growth rate (μ_max) augmented from 0.17 to 0.22 h⁻¹ and entomotoxicity (Tx) increased by 29.7%. Meanwhile, volumetric mass transfer coefficient (k_La) showed marked variations during fermentation, and oxygen uptake rate (OUR) increased 2-fold. The proteolytic activity increased while chitinase decreased for Tween amended wastewater sludge, but the entomotoxicity increased. The specific entomotoxicity followed power law when plotted against spore concentration and the relation between Tx and protease activity was linear. The viscosity varied and volume percent of particles increased in Tween-80 amended wastewater sludge and particle size (D₅₀) decreased at the end of fermentation. Thus, there was an increase in entomotoxicity at higher suspended solids (30 g/L) as Tween addition improved rheology (viscosity, particle size, surface tension); enhanced maximum growth rate and OUR.     

Impact of iron salts on activated sludge and interaction with nitrite or nitrate

Iron salts are often used in activated sludge treatment plants as coagulants or to improve reactor performance. Previous studies have indicated that iron itself has an impact on the activated sludge process. However, the interaction of iron with nitrite or nitrate present in the sludge has received little attention. In this research, the influence of addition of Fe(II) or Fe(III), alone or together with NO(2)(-) or NO(3)(-) on bench-scale activated sludge reactors was examined. Large differences were established between the distinct treatments, regarding reactor performance, sludge characteristics as well as microbial community. Ferric iron was more detrimental than ferrous iron. In some cases, nitrite was found to enhance inhibitory effects of the added iron, whereas nitrate had more a neutralizing effect. It was found that precipitation of phosphate by the iron was not responsible for the observed inhibition. Decrease in pH upon formation of iron hydroxides and the impairment of the floc structure could partially explain the toxicity of the iron dosages. The formation of toxic nitrogen oxides, such as nitric oxide, can also be of importance. The observed positive effect of nitrate on the floc activity is of interest and warrants further elucidation.     

Transient response of aerobic and anoxic activated sludge activities to sudden substrate concentration changes

The state-of-the-art understanding of activated sludge processes as summarized in activated sludge models (ASMs) predicts an instantaneous increase in the biomass activity (which is measured, e.g., by the corresponding respiration rate OUR, NUR, etc.) under sudden substrate concentration changes. Experimental data (e.g., short-term batch respiration experiments under aerobic or anoxic conditions) collected for the calibration of the dynamic models (ASMs) often exhibit a transient phenomenon while attaining maximum activity, which cannot be explained by the current understanding of the activated sludge process. That transient phenomenon exhibits itself immediately upon addition of a substrate source to an endogenously respiring activated sludge sample and it usually takes a few minutes until the activated sludge reaches its maximum possible rate under given environmental conditions. This discrepancy between the state-of-the-art model and the experimental data is addressed in detail in this investigation. It is shown that the discrepancy is not caused by an error in the experimental set-up/data but it is rather due to model inadequacy. Among the hypotheses proposed, it appears that this transient response of the activated sludge most likely results from the sequence of intracellular reactions involved in substrate degradation by the activated sludge. Results from studies performed elsewhere with pure cultures (S. cerevisae and E. coli) support the hypothesis. The transient phenomenon can be described by a dynamic metabolic network model or by a simple first-order model, as adopted in this study. The transient phenomenon occurring in short-term batch respiration experiments is shown to interfere severely with parameter estimation if not modeled properly (2.8%, 11.5%, and 16.8% relative errors [average of three experiments] on Y(H), micro(maxH), and K(S), respectively). Proper modeling of this transient phenomenon whose time constant is on the order of minutes (1 to 3 min) is expected to contribute fundamentally to a better understanding and modeling of Orbal, carousel, and SBR-type treatment plants with fast-alternating process conditions, although such studies are beyond the scope of this report.     

The effect of pH on the efficiency of an SBR processing piggery wastewater

To treat piggery wastewater efficiently, the hydrolysis of urea (mainly derived from swine urine) in piggery wastewater with the change of sewage pH must be considered. Using activated sludge, piggery wastewater was treated in a sequencing batch reactor (SBR), and the effects of influent pH on SBR processing efficiency, sludge settle ability, and sludge activity were investigated. The results showed that a high influent pH value contributed to the improvement of the removal rate of ammonia nitrogen and reduction of the chemical oxygen demand (COD). When the influent pH was between 9.0 and 9.5, the removal rate of ammonia nitrogen was higher than 90%, and the reduction of COD from its original value was 80%. The influent pH had a greater influence on sludge concentration and sludge activity. When the influent pH increased from 7.0 to 9.5, the sludge concentration increased from 2,350 to 3,947 mg/L in the reactor, and the activities of ammonium oxidizing bacteria (AOB) and nitrite oxidizing bacteria (NOB) first increased and then decreased. When the influent pH was 9.0 and 8.0, the maximum values (0.48 g O₂/(g MLSS/day) and 0.080 g O₂/(g MLSS/day)) were reached, and the sludge settling ratio was nearly steady between 20 and 35% in each reactor.     

Xenobiotic substrate reduces yield of activated sludge in a continuous flow system

The biomass yield of a continuous flow activated sludge system varied when the system treated influent containing different compositions of biogenic and xenobiotic substrates. Both the biogenic substrate and a test xenobiotic 2,4-dichlorophenoxyacetic acid (2,4-D) were degraded at steady-state activated sludge operations. The true yields, determined from steady-state activated sludge treatment performances, were at the maximum and the minimum when the activated sludge treated the influent of sole biogenic substrate and sole 2,4-D, respectively. The minimum yield was 56% of the maximum. Yield reduction between the maximum and the minimum was proportional to the concentration of 2,4-D in the influent. This trend of yield reduction suited a model that describes the metabolic uncoupling effect of 2,4-D on the sludge's degradation of the substrates. The model function variable was defined as the ratio of 2,4-D to biogenic COD concentrations in the influent.     

三氯乙酸(TCA)提取法与微波提取法检测活性污泥中三磷酸腺苷(ATP)

【目的】针对活性污泥法中的重要参数ATP进行研究分析,通过在不同条件下检测污泥的活性,得出以ATP为指标的污泥活性状态,为准确判定活性污泥的活性提供依据。【方法】分别运用三氯乙酸(TCA)提取法及微波提取法检测活性污泥中的ATP,并对检测ATP的影响因素(TCA浓度、冰浴时间、p H、微波频率及时间等)进行探讨与优化。【结果】运用TCA提取法检测ATP时,在1.0%-7.0%的TCA体积百分数内,活性污泥中TCA最佳体积百分数为2.5%;在2-60 min的冰浴时间内,最佳冰浴时间为10 min;三羟甲基丙烷-乙二胺四乙酸(Tris-EDTA)缓冲液的最佳p H 7.5;运用微波提取法检测ATP适宜的微波辐射条件为:功率800 W,辐射时间15 s。【结论】TCA提取法和微波提取法均可以检测活性污泥中的ATP,但与微波提取法相比,TCA提取法更能保证从细胞内释放出来的ATP的完整性,因此TCA提取法更适合用于检测活性污泥中的ATP。     

Polyphosphate-degrading enzymes in Acinetobacter spp. and activated sludge

Polyphosphate-degrading enzymes were studied in Acinetobacter spp. and activated sludge. Polyphosphate: AMP phosphotransferase activity in Acinetobacter strain 210A decreased with increasing growth rates. The activity of this enzyme in cell extracts of Acinetobacter strain 210A was maximal at a pH of 8.5 and a temperature of 40 degrees C and was stimulated by (NH4)2SO4. The Km for AMP was 0.6 mM, and the Vmax was 60 nmol/min per mg of protein. Cell extracts of this strain also contained polyphosphatase, which was able to degrade native polyphosphate and synthetic magnesium polyphosphate and was strongly stimulated by 300 to 400 mM NH4Cl. A positive correlation was found between polyphosphate:AMP phosphotransferase activity, adenylate kinase activity, and phosphorus accumulation in six Acinetobacter strains. Significant activities of polyphosphate kinase were detected only in strain P, which contained no polyphosphate:AMP phosphotransferase. In samples of activated sludge from different plants, the activity of adenylate kinase correlated well with the ability of the sludge to remove phosphate biologically from wastewater.     

Polyphosphate-degrading enzymes in Acinetobacter spp. and activated sludge.

Polyphosphate-degrading enzymes were studied in Acinetobacter spp. and activated sludge. Polyphosphate: AMP phosphotransferase activity in Acinetobacter strain 210A decreased with increasing growth rates. The activity of this enzyme in cell extracts of Acinetobacter strain 210A was maximal at a pH of 8.5 and a temperature of 40 degrees C and was stimulated by (NH4)2SO4. The Km for AMP was 0.6 mM, and the Vmax was 60 nmol/min per mg of protein. Cell extracts of this strain also contained polyphosphatase, which was able to degrade native polyphosphate and synthetic magnesium polyphosphate and was strongly stimulated by 300 to 400 mM NH4Cl. A positive correlation was found between polyphosphate:AMP phosphotransferase activity, adenylate kinase activity, and phosphorus accumulation in six Acinetobacter strains. Significant activities of polyphosphate kinase were detected only in strain P, which contained no polyphosphate:AMP phosphotransferase. In samples of activated sludge from different plants, the activity of adenylate kinase correlated well with the ability of the sludge to remove phosphate biologically from wastewater.