Electrochemical immune-biosensor for immunoglobulin G based bioelectrocatalytic reaction on micro-comb electrodes

A new amplification strategy of electrochemical signaling from antigen-antibody interactions was proposed via back-filling immobilization of horseradish peroxidase (HRP), immunoglobulin G antibodies (anti-IgG) and gold nanoparticles onto a three-dimensional sol-gel (3DSG)-functionalized biorecognition interface. The 3DSG sol-gel network was employed not only as a building block for the surface modification but also as a matrix for ligand functionalization. The signal-amplification was based on the bioelectrocatalytic reaction of the back-filling immobilization of HRP to H(2)O(2). With the non-competitive format, the formation of the antigen-antibody complex by a simple one-step immunoreaction between the immobilized anti-IgG and IgG in sample solution inhibited partly the active center of HRP, and decreased the immobilized HRP towards H(2)O(2) reduction. Under optimal conditions, the proposed immunosensor exhibited a good electrochemical behavior to IgG in a dynamic range of 1.12-162 ng/mL with a detection limit of 0.56 ng/mL (at 3delta). Moreover, the precision, reproducibility and stability of the as-prepared immunosensor were acceptable. Importantly, the proposed methodology would be valuable for diagnosis and monitoring of biomarkers and its metastasis.     

Signal amplification of electrochemical immunosensor for the detection of human serum IgG using double-codified nanosilica particles as labels

A simple and sensitive method for in situ amplified electrochemical immunoassay of human serum IgG has been developed by using double-codified nanosilica particles as labels based on horseradish peroxidase-doped nanosilica particles (HRP-SiO(2)) with the conjugation of anti-IgG antibodies (anti-IgG-SiO(2)-HRP). With the sandwich-type immunoassay format, the linear range of the developed immunosensor by using anti-IgG-SiO(2)-HRP as tracer and hydrogen peroxide (H(2)O(2)) as enzyme substrate is 0.01-15 nmol/L IgG with a detection limit of 5.0 pmol/L, while the assay sensitivity by directly using HRP-labeled anti-IgG as secondary antibodies is 1.0-10 nmol/L with a detection limit of 0.1 nmol/L IgG. The reproducibility, stability and specificity of the proposed immunoassay method were acceptable. The IgG concentrations of the clinical serum specimens assayed by the developed immunosensor show consistent results in comparison with those obtained by commercially available enzyme-linked immunosorbent assay (ELISA) method.     

Enzyme immunosensors based on electropolymerized polytyramine modified electrodes

Highly sensitive amperometric enzyme immunosensors for human immunoglobulin G (IgG) were prepared on the basis of electrogenerated polytyramine (PTy, tyramine = p-(2-aminoethyl)-phenol) modified electrodes. Properties of PTy films changed depending on electrolysis conditions. On the basis of the found properties of the films, an effective IgG sensor was prepared: a PTy film was formed first from an acid solution on a Pt electrode, and the surface was further covered with a PTy film from an alkaline methanol solution to give a PTy doubly coated electrode on which anti-IgG was then immobilized. This electrode provided a large surface area with little non-specific adsorption of proteins. By means of the competitive enzyme immunoassay technique using glucose oxidase (GOD) labeled IgG conjugates, IgG was determined in the concentration range of c. 10 pg/ml-1 mg/ml from the oxidation current of H2O2 generated by the enzyme (GOD) reaction using the above IgG sensor. Also, an anti-IgG immobilized electrode, prepared by using a Pt electrode singly covered with a PTy film from an alkaline methanol solution, acted as an effective IgG sensor with a detection limit for IgG of c. 100 pg/ml.     

Functional properties of proteins immobilized on albumin microspheres

Bovine serum albumin (BSA) microspheres with an average diameter of 12.5 micron were prepared by crosslinking of BSA molecules with glutaraldehyde in the presence of polymethylmethacrylate dissolved in chloroform-toluene. Trypsin and anti-human IgG antibody were immobilized onto their surfaces by the glutaraldehyde-activation method. The catalytic activity and storage stability of the immobilized trypsin were satisfactorily high. The enzyme immunoassay (EIA) method using BSA-microspheres as a solid phase has a high sensitivity (the minimum concentration of detectable antigen in the sample: 0.2 ng/ml) and a wide concentration range (final concentration 0.027-3000 ng/ml) for the detection of human IgG.     

Immobilization of biocomponents for immune optical sensors

Immobilisation of both human immunoglobulin(IgG) and antiimmunoglobulin (anti-IgG) was performed by means of polyelectrolyte self-assembly. This technique was compared with direct immobilisation of the immune components on bare gold and their covalent binding via glutaraldehyde as a bifunctional reagent. Additionally, the immune components were properly oriented during their immobilisation by using a predeposited layer of the protein A. Methods of the surface plasmon resonance (SPR) and planar interferometry were employed for monitoring the immobilisation as well as specific immune reaction. It was shown that in case of the use of polyelectrolyte self-assembly it is possible to achieve the sensitivity of the analysis up to 30 ng/ml for SPR and up to 1 ng/ml for planar interferometer based immune sensors.     

Sensitive electrochemical enzyme immunoassay microdevice based on architecture of dual ring electrodes with a sensing cavity chamber

A novel electrochemical detection architecture was investigated for enzyme immunoassay sensors. Microchips with dual-ring working and counter electrodes, and a sensing cavity chamber were made on glass slides. The glass surface of the microchip was coated by 3-aminopropyltriethoxysilane (APTES). Goat IgG, as a example, was covalently captured on APTES-modified glass surfaces through glutaraldehyde (GA) as a cross-linker. Enzyme substrate, p-aminophenyl phosphate (PAPP) was prepared by electrolysis. The enzyme conversion from home-synthetic PAPP to p-aminophenol (PAP) was examined by differential pulse voltammetry (DPV). A competitive inhibition enzyme-linked immunosorbant assay (ELISA) was designed to test the system. Experimental results demonstrate that a detection limit of 118 fg/ml of goat IgG and a dynamic range of 118 fg/ml to 1.18 ng/ml, up to five orders of magnitude could be achieved. Due to its novel architecture design and electronic detection scheme, the method can be used to fabricate portable electrochemical ELISA lab-on-chip systems. The technology could have great potential in clinical diagnostic applications.     

Development of a fluorescence immunoassay for measurement of paclitaxel in human plasma

A new fluorescence immunoassay for the quantitative determination of paclitaxel (Pac) under equilibrium conditions was developed. Anti-Pac IgG2a antibody was immobilized through its Fc region to protein A covalently bound to the inside surface of a silanized glass capillary column and the antigen-binding sites of anti-Pac saturated with rhodamine-labeled Pac (Rh-Pac). Analyte Pac was circulated through the column in a closed loop and the steady-state fluorescence of the Rh-Pac displaced from the immobilized antibody was recorded after 6 min. The Rh-Pac fluorescence emission intensity was directly related to the concentration of the Pac analyte over a broad dynamic range of up to 400 ng/ml with a linear range up to 200 ng/ml and lower detection limit of 5.85 ng/ml. While there was no interference from the baccatin III and 10-deacetylbaccatin III, cephalomannine was found to interfere in Pac determination. When applied for measurement of Pac in human plasma, the concentration of Pac determined by the fluorescence assay was found to be in excellent agreement with the Pac added, confirming the potential of the fluorescence immunoassay for clinical application.     

Effectiveness of methods of isolating specific class-G rabbit antibodies for the immunoenzyme determination of human placental alkaline phosphatase

Four different chromatographic methods of IgG isolation from rabbit antisera to placental alkaline phosphatase (HPAP) have been compared. The antibodies were obtained by ion-exchange chromatography and affinity chromatography on protein-A-sepharose, on the sepharose with immobilized antigen. IgG samples were characterized by the content of specific antibodies to HPAP and checked in enzyme immunoassay (EIA). IgG purified on immobilized antigen were found to be the optimal both from the point of view of the specific antibodies content and EIA sensitivity, but satisfactory results could be also obtained with ion-exchange and protein-A-chromatography purified IgG. The last two isolation methods are simpler and provide 3-10 ng/ml sensitivity of HPAP detection, which is lower, as compared with the test employing affinity antibodies (1 ng/ml), but allows the detection of HPAP in serum samples.     

Micro-machined piezoelectric membrane-based immunosensor array

This paper reports a micro-machined piezoelectric membrane-based biosensor array for immunoassay. Goat immunoglobulin G (IgG) and HBsAg were immobilized as the probe molecules on the square piezoelectric membranes of the sensors that have dimensions of 3.5 microm x 500 microm x 500 microm. Due to the mass sensitive nature of these sensors, their resonant frequencies were depressed after the anti-goat IgG or anti-HBsAg was captured by the goat IgG or HBsAg. The resonant frequencies of the sensors were measured by an impedance analyzer. The experimental results demonstrate that the measured frequency change varies from 100 to 700 Hz, and the mass sensitivity of the device is estimated to be about 6.25 Hz/ng. A near linear relationship between the frequency change and the concentration of goat IgG was obtained, and the mass of the attached anti-goat IgG was calculated. The preliminary results discussed in this work indicate that the micro-machined piezoelectric membrane-based biosensor has a potential application as an immunosensor.     

Investigation of dual-layer membrane cloaking method by surface plasmon resonance for direct chronoamperometric immunoassay of serum sample

A "dual-layer membrane cloaking" (DLMC) method was developed to construct disposable electrochemical immunosensor for direct determination of serum sample. Mouse IgG (MIgG) molecules were firstly immobilized on a substrate. After the formation of a didodecyldimethylammonium bromide (DDAB) membrane on the MIgG modified substrate, an additional bovine serum albumin (BSA) thin layer was formed to build a BSA/DDAB dual-layer membrane (DLM). When alkaline phosphatase conjugated anti-mouse IgG antibodies (anti-MIgG-ALP) in human serum were incubated on the substrate, anti-MIgG-ALP was recognized specifically by the immobilized MIgG while all nonspecifically adsorbed proteins were selectively removed together with BSA/DDAB DLM by 5% Triton X-100 (v/v) before final measurements. The BSA/DDAB DLM was characterized and optimized by surface plasmon resonance (SPR) technique, and further employed in a disposable immunoassay based on an ITO chip. Under optimal conditions, MIgG in human serum was directly detected in the range of 2.0-18.0 ng mL(-1) without dilution or separation. A limit of detection as low as 0.922 ng mL(-1) (6.15 pM) was obtained. The proposed DLMC method can efficiently prevent the penetration of matrix proteins through single cloaking membrane and completely eliminate nonspecific adsorption. It has great potential in providing a versatile way for direct determination of serum sample with ultra-sensitivity.     

Use of thiol-terminal silanes and heterobifunctional crosslinkers for immobilization of antibodies on silica surfaces

A procedure for covalent immobilization of functional proteins on silica substrates was developed using thiol-terminal silanes and heterobifunctional cross-linkers. Using this procedure, a high density of functional antibodies was bound to glass cover slips and silica fibers. The amount of anti-IgG antibody immobilized was determined to be in the range of 0.66 to 0.96 ng/mm2 using radiolabeled antibody. The relative amount of IgG antigen bound by the immobilized antibody (0.37 to 0.55 mol antigen/mol antibody) was three to five times greater than other investigators have reported. In addition, the amount of protein nonspecifically adsorbed to the antibody-coated surface was further reduced by the addition of blocking agents so that nonspecific adsorption of protein antigens represented only 2-6% of the total antigen binding. With this low background, IgG antigen binding could be measured at levels as low as 150 fmol when an antigen concentration of 3 pmol/ml was applied. The process for antibody immobilization is straightforward, easy to perform, and adaptable for modifying mass quantities of biosensor components.     

Establishment and validation of an immunoenzymatic assay to determine mouse IgG levels based on a rat monoclonal antibody

In this paper we describe an immunoenzymatic assay based on a rat monoclonal antibody (Ram kappa) developed to determine mouse IgG concentration, which is widely used for samples obtained on purification processes, like supernatant waste and the content of IgG in the vaccine (rHBsAg). This assay involves the use of a rat antibody-horseradish peroxidase-conjugated for the revealing of the antigen-antibody reaction. The rat antibody was produced in cell culture using a dialysis tube (DT). The immunoassay was standardized following several concepts, such as specificity, precision, and linearity. The result obtained permitted us to replace the use of polyclonal antibodies to determine the kappa light chain mouse antibodies by a rat monoclonal antibody of high sensibility and reproducibility. The assay permitted a reliable measurement of murine kappa Ig up to 0.68 ng/ml and was capable of quantifying 6.25 ng/ml. Due to the high frequency of the kappa light chain in mouse antibodies this system acquires a great application.     

A sensitive amperometric immunosensor for carcinoembryonic antigen detection with porous nanogold film and nano-Au/chitosan composite as immobilization matrix

A sensitive amperometric immunosensor for carcinoembryonic antigen (CEA) was prepared. Firstly, a porous nano-structure gold (NG) film was formed on glassy carbon electrode (GCE) by electrochemical reduction of HAuCl₄ solution, then nano-Au/Chit composite was immobilized onto the electrode because of its excellent membrane-forming ability, and finally the anti-CEA was adsorbed onto the surface of the bilayer gold nanoparticles to construct an anti-CEA/nano-Au/Chit/NG/GCE immunosensor. The characteristics of the modified electrode at different stages of modification were studied by cyclic voltammetry (CV). The gold colloid, chitosan and nano-Au/Chit were characterized by transmission electron microscopy and UV–vis spectroscopy. In addition, the performances of the immunosensor were studied in detail. The resulting immunosensor offers a high-sensitivity (1310 nA/ng/ml) for the detection of CEA and has good correlation for detection of CEA in the range of 0.2 to 120.0 ng/ml with a detection limit of 0.06 ng/ml estimated at a signal-to-noise ratio of 3. The proposed method can detect the CEA through one-step immunoassay and would be valuable for clinical immunoassay.     

Feasibility of protein A for the oriented immobilization of immunoglobulin on silicon surface for a biosensor with imaging ellipsometry

The feasibility of using protein A to immobilize antibody on silicon surface for a biosensor with imaging ellipsometry was presented in this study. The amount of human IgG bound with anti-IgG immobilized by the protein A on silicon surface was much more than that bound with anti-IgG immobilized by physical adsorption. The result indicated that the protein A could be used to immobilize antibody molecules in a highly oriented manner and maintain antibody molecular functional configuration on the silicon surface. High reproducibility of the amount of antibody immobilization and homogenous antibody adsorption layer on surfaces could be obtained by this immobilization method. Imaging ellipsometry has been proven to be a fast and reliable detection method and sensitive enough to detect small changes in a molecular monolayer level. The combination of imaging ellipsometry and surface modification with protein A has the potential to be further developed into an efficient immunoassay protein chip.     

Highly sensitive detection of cocaine using a piezoelectric immunosensor

This paper describes the development of a highly sensitive competitive immunoassay with the piezoelectric sensor. The immobilized derivative of cocaine was benzoylecgonine-1,8-diamino-3,4-dioxaoctane (BZE-DADOO). For the immobilization of BZE-DADOO, the conjugate BZE-DADOO with 11-mercaptomonoundecanoic acid (MUA) was synthesized via 2-(5-norbornen-2,3-dicarboximide)-1,1,3,3-tetramethyluronium-tetrafluoroborate (TNTU), followed by the creation of the conjugate monolayer on the piezosensor electrodes. For the optimization of the competitive assay we used electrodes with rough or smooth gold areas and for the interaction with immobilized antigen different anti-cocaine sheep polyclonal (pAb, either whole IgG or Fab fragment) and mouse monoclonal (mAb, whole IgG) antibodies. The assay of cocaine developed achieved a detection limit (LOD) of 100 pmol/l (34 ng/l) using the sheep antibody (IgG) and piezoelectric sensors with a smooth gold surface. The total time of one analysis was 15 min and the measuring area of the sensor could be used more than 40 times without losing its sensitivity.     

Ultrasensitive electrochemical immunosensor employing glucose oxidase catalyzed deposition of gold nanoparticles for signal amplification

This paper describes a novel enzymatic amplification strategy for ultrasensitive electrochemical immunosensing. This approach utilizes glucose oxidase for the enzymatic deposition of gold nanoparticles onto an indium tin oxide (ITO) electrode surface using a novel gold developer solution consisting of 20 mM of glucose, 20 mM of NaSCN, 0.5 M of p-benzoquinone (PBQ) and 1 mM of AuCl(4)(-) dissolved in 0.1 M of pH 7.5 phosphate buffer solution. The amount of gold deposited was quantified electrochemically by monitoring the reduction of gold oxide in an aqueous solution of 0.5 M of H(2)SO(4), which was correlated to the amount of antigens in the solution. The effectiveness of this strategy was demonstrated experimentally through the construction of an immunosensor for the detection of mouse IgG using a sandwich immunoassay in a linear dynamic range of 5 pg/ml to 50 ng/ml. A good mean apparent recovery in the range of 88-102% was obtained over the entire linear dynamic range of the sensor response in the serum samples. This suggested that the immunosensor would be useful for the testing of proteins in real clinical samples.     

Continuous monitoring of IgG using immobilized fluorescent reporters

In the manufacture of therapeutic monoclonal antibodies, the clarified cell culture fluid (CCF) is typically loaded onto an initial protein A affinity capture column. Imperfect mass transfer and loading to maximum capacity can risk antibody breakthrough and loss of valuable product, but conservative underloading wastes expensive protein A resin. In addition, the effects of column fouling and ligand degradation require the frequent optimization of immunoglobulin G (IgG) loading to avoid wastage. Continuous real-time monitoring of IgG flowthrough is of great interest, therefore. We previously developed a fluorescence-based monitoring technology that allows batch mix-and-read mAb detection in the CCF. Here, we report the use of reporters immobilized on cyanogenbromide-activated Sepharose 4B resin for continuous detection of IgG in column breakthrough. The column effluent is continuously contacted with immobilized fluorescein-labeled Fc-binding ligands in a small monitoring column to produce an immediately-detectable change in fluorescence intensity. The technology allows rapid and reliable monitoring of IgG in a flowing stream of clarified CCF emerging from a protein A column, without prior sample preparation. We observed a significant change in fluorescence intensity at 0.5 g/L human IgG, sufficient to detect a 5% breakthrough of a 10 g/L load, within 18 s at a flow rate of 0.5 ml/min. The current small-scale technology is suitable for use in process development, but the chemistry should be readily adaptable to larger scale applications using fiber-optic sensors, and continuous IgG monitoring could be applicable in a variety of upstream and downstream process settings.     

Electrochemical detection of HbA1c, a marker [correction of maker] for diabetes, using a flow immunoassay system

An on-chip electrochemical flow immunoassay system for the detection of hemoglobin A1c (HbA1c) was developed using anti-human hemoglobin (Hb) IgG labeled with ferrocene monocarboxylic acid (Fc-COOH) and boronate-affinity chromatography. An on-chip column packed with boronate-activated agarose beads was used for the separation of HbA1c from both non-glycated Hb and free antibody. Anti-human Hb IgG conjugated to Fc-COOH (Fc-IgG) was used for the electrochemical detection of HbA1c. The assay procedure included immunoreactions with Fc-IgG and HbA1c, separation of immunocomplexes by boronate affinity, and electrochemical detection of Fc-IgG-HbA1c immunocomplexes. The immunoreaction mixtures were injected onto a boronate-affinity column. HbA1c-antibody complexes were then trapped onto the column by the affinity of HbA1c to boronic acid. Subsequently, elution buffer containing sorbitol was applied to elute HbA1c-antibody complexes and a current was detected by applying 600 mV versus Ag/AgCl. The elution signal was an estimation of the HbA1c amount. A linear correlation between the increase of current and HbA1c concentration was obtained up to an HbA1c concentration of 500 microg/ml. The HbA1c flow immunoassay was successfully achieved using hemolysates. This electrochemical flow immunoassay system enabled us to construct a novel point-of-care testing device for the monitoring of glycated proteins including HbA1c.     

Layer-by-layer hydroxymethyl ferrocene modified sensor for one-step flow/stop-flow injection amperometric immunoassay of alpha-fetoprotein

A rapid one-step flow/stop-flow injection amperometric immunoassay for alpha-fetoprotein (AFP) using a novel home-produced electrochemical sensor was proposed. The sensor was prepared using layer-by-layer adsorption of positively charged poly(allylamine) (PAA) and negatively charged hydroxymethyl ferrocene on a screen-printed electrode (SPE). The electrochemistry of the immobilized ferrocene moieties showed a surface-controlled electrode process. Based on an electrochemical enzyme-linked immunoassay with the immobilized ferrocene moieties as an electron transfer mediator between the electrode and the horseradish peroxidase (HRP)-labeled anti-AFP antibody, a calibration curve with two linear ranges from 5 to 20 and 20 to 150 ng ml-1 and a detection limit of 2 ng ml-1 for AFP determination was obtained under the optimized conditions of 0.891 ml min-1 flow rate, 20 microl injection volume and +25 mV applied potential. The sensor showed good repeatability and reproducibility and retained more than 95% of its original signal after 15 days of storage. The proposed method eliminated the need for washing and addition of any substrate or mediator. The complete assay could be handled in less than 25 min with a one-step injection of a 40 microl sample solution. The proposed method would be valuable for the diagnosis and monitoring of carcinoma and its metastasis.     

人IgG标记金纳米棒并用于抗人IgG抗体的检测

目的：研究金纳米棒（GNRs）IgG生物学标记及其在抗人IgG检测中的应用。方法：利用种子生长法制备GNRs,用巯基十一酸（MUA）对GNRs端头邀111妖晶面进行化学修饰,MUA提供的羧基可与人IgG结合;抗人IgG与活化的GNRs反应引起GNRs表面等离子体共振（SPR）特征变化,通过读取SPR值判断免疫反应的结果。结果：合成了不同长径比（AR）的GNRs,成功地将人IgG标记于GNRs（AR=3.7）的端头;利用标记后的GNRs对抗人IgG进行检测,其SPR最大吸收峰发生9nm红移,检测灵敏度可达纳摩尔量级。结论：基于人IgG-抗人IgG免疫反应建立了GNRs用于免疫检测的方法,为GNRs用于免疫检测进而研制免疫传感器奠定了基础。