Disinfection of selected Aspergillus spp. using ultraviolet germicidal irradiation

AIMS: The efficacy of ultraviolet germicidal irradiation (UVGI) and the UVGI dose necessary to inactivate fungal spores on an agar surface for cultures of Aspergillus flavus and Aspergillus fumigatus were determined. METHODS AND RESULTS: A four-chambered UVGI testing unit with a 9-W, Phillips, low pressure, mercury UVGI lamp in each chamber was used in this study. An aperture was adjusted to provide 50, 100, 150, and 200 micro W/cm2 of uniform flux to the surfaces of the Petri dish, resulting in a total UVGI dose to the surface of the Petri dishes ranging from 12 to 96 mJ/cm2. The UVGI dose necessary to inactivate 90% of the A. flavus and A. fumigatus was 35 and 54 mJ/cm2, respectively. CONCLUSIONS: UVGI can be used to inactivate culturable fungal spores. Aspergillus flavus was more susceptible than A. fumigatus to UVGI. SIGNIFICANCE AND IMPACT OF THE STUDY: These results may not be directly correlated to the effect of UVGI on airborne fungal spores, but they indicate that current technology may not be efficacious as a supplement to ventilation unless it can provide higher doses of UVGI to kill spores traveling through the irradiated zone.     

Ultraviolet germicidal irradiation disinfection of Stachybotrys chartarum

The ultraviolet germicidal irradiation (UVGI) dose necessary to inactivate fungal spores on an agar surface and the efficacy of UVGI were determined for cultures of Stachybotrys chartarum (ATCC 208877). This study employed a UVGI testing unit consisting of four chambers with a 9-W, Phillips, low pressure, mercury UVGI lamp in each chamber. The testing unit's apertures were adjusted to provide 50, 100, 150, and 200 microW/cm2 of uniform flux to the Petri dish surfaces, resulting in a total UVGI surface dose ranging from 12 to 144 mJ/cm2. The UVGI dose necessary to inactivate 90% of the S. chartarum was greater than the maximum dose of 144 mJ/cm2 evaluated in this study. While UVGI has been used to inactivate several strains of culturable fungal spores, S. chartarum was not susceptible to an appropriate dose of UVGI. The results of this study may not correlate directly to the effect of UVGI on airborne fungal spores. However, they indicate that current technology may not be efficacious as a supplement to ventilation unless it can provide higher doses of UVGI to kill spores, such as S. chartarum, traveling through the irradiated zone.     

Chlorination of indicator bacteria and viruses in primary sewage effluent

Wastewater disinfection is used in many countries for reducing fecal coliform levels in effluents. Disinfection is therefore frequently used to improve recreational bathing waters which do not comply with microbiological standards. It is unknown whether human enteric viruses (which are responsible for waterborne disease) are simultaneously inactivated alongside fecal coliforms. This laboratory study focused on the chlorination of primary treated effluent with three doses (8, 16, and 30 mg/liter) of free chlorine as sodium hypochlorite. Seeding experiments showed that inactivation (>5 log(10) units) of Escherichia coli and Enterococcus faecalis was rapid and complete but that there was poor inactivation (0.2 to 1.0 log(10) unit) of F(+)-specific RNA (FRNA) bacteriophage (MS2) (a potential virus indicator) at all three doses. However, seeded poliovirus was significantly more susceptible (2.8 log(10) units) to inactivation by chlorine than was the FRNA bacteriophage. To ensure that these results were not artifacts of the seeding process, comparisons were made between inactivation rates of laboratory-seeded organisms in sterilized sewage and inactivation rates of organisms occurring naturally in sewage. Multifactorial analysis of variance showed that there was no significant difference (P > 0.05) between the inactivation rates for seeded and naturally occurring FRNA bacteriophage. However, laboratory-grown poliovirus was inactivated much more rapidly than were naturally occurring, indigenous enteroviruses (P < 0.001). This may reflect differences in the way indigenous virus is presented to the disinfectant. Inactivation rates for indigenous enteroviruses were quite similar to those seen for FRNA bacteriophage at lower doses of chlorine. These results have significance for the effectiveness of chlorination as a sewage treatment process, particularly where virus contamination is of concern, and suggest that FRNA bacteriophage would be an appropriate indicator of such viral inactivation under field conditions.     

Susceptibility of Burkholderia cepacia and other pathogens of importance in cystic fibrosis to u.v. light

To investigate the potential usefulness of u.v. germicidal irradiation (UVGI) in preventing the spread of Burkholderia cepacia, an important pathogen in cystic fibrosis (CF), the in-vitro susceptibility of B. cepacia to UVGI was determined. Five strains were exposed to UVGI from a 7.2-W source. Burkholderia cepacia was less susceptible to UVGI than other important CF-related pathogens, namely Staphylococcus aureus and Pseudomonas aeruginosa, but was more susceptible than Stenotrophomonas maltophilia. No strain of B. cepacia survived longer than an 8 s exposure to UVGI, with doses required to achieve 1 log reduction in bacterial numbers ranging from 28.3 to 57.5 J m(-2).     

Size and UV germicidal irradiation susceptibility of Serratia marcescens when aerosolized from different suspending media

Experimental systems have been built in laboratories worldwide to investigate the influence of various environmental parameters on the efficacy of UV germicidal irradiation (UVGI) for deactivating airborne microorganisms. It is generally recognized that data from different laboratories might vary significantly due to differences in systems and experimental conditions. In this study we looked at the effect of the composition of the suspending medium on the size and UVGI susceptibility of Serratia marcescens in an experimental system built in our laboratory. S. marcescens was suspended in (i) distilled water, (ii) phosphate buffer, (iii) 10% fetal calf serum, (iv) phosphate-buffered saline (saline, 0.8% sodium chloride), and (v) synthetic saliva (phosphate-buffered saline with 10% fetal calf serum). At low humidity (36%), S. marcescens suspended in water-only medium was the most susceptible to UVGI, followed by those in serum-only medium. The count median diameters (CMDs) for culturable particles from water-only and serum-only media were 0.88 and 0.95 micro m, respectively, with the measurements based on their aerodynamic behavior. The bacteria suspended in phosphate buffer, synthetic saliva, and phosphate-buffered saline had similar UVGI susceptibility and CMD at 1.0, 1.4, and 1.5 micro m, respectively. At high humidity (68%) the CMD of the particles increased by 6 to 16%, and at the same time UVGI susceptibility decreased, with the magnitude of decrease related to the type of suspending medium. In conclusion, the choice of suspending medium influenced both size and UVGI susceptibility of S. marcescens. These data are valuable for making comparisons and deciding on the use of an appropriate medium for various applications.     

Laboratory-scale inactivation of African swine fever virus and swine vesicular disease virus in pig slurry

Two methods were evaluated for the inactivation of African swine fever (ASV) and swine vesicular disease (SVD) viruses in pig slurry: chemical treatment and heat treatment. The addition of NaOH or Ca(OH)2 at different concentration/time combinations at 4 degrees C and 22 degrees C was examined, as was virus stability at different temperature/time combinations. ASF virus (ASFV) was less resistant to both methods than SVD virus (SVDV). In slurry from one source, ASFV was inactivated at 65 degrees C within 1 min, whereas SVDV required at least 2 min at 65 degrees C. However, it was found that thermal inactivation depended on the characteristics of the slurry used. Addition of 1% (w/v) of NaOH or Ca(OH)2 caused the inactivation of ASFV within 150 s at 4 degrees C; 0.5% (w/v) NaOH or Ca(OH)2 required 30 min for inactivation. NaOH or Ca(OH)2 (1% (w/v)) was not effective against SVDV at 22 degrees C after 30 min, and 1.5% (w/v) NaOH or Ca(OH)2 caused inactivation of SVDV at both 4 degrees C and 22 degrees C. At higher chemical concentrations or temperatures, ASFV and SVDV inactivation was faster in slurry than in buffered medium.     

Stability of minute virus of mice against temperature and sodium hydroxide.

Treatment with steam and/or dilute NaOH are commonly used techniques to disinfect manufacturing vessels and tools in the pharmaceutical industry. The aim of this procedure is sanitisation and inactivation of microbiological and viral contaminants. Here we describe the inactivation of the mouse parvovirus Minute Virus of Mice (MVM) under these conditions. Parvoviruses are known to be resistant to physico-chemical treatment and one representative of this family, the human parvovirus B19, is a potential contaminant of blood plasma. We show inactivation kinetics for MVM treated with wet-heat (70, 80, 90 degrees C) and with 0.01-1 M NaOH solutions (pH >/=11.9). Robust inactivation was only achieved at 90 degrees C for at least 10 min and in NaOH solutions of pH >/=12.8 (0.1 M NaOH). It was observed, that aggregation of viruses might protect viral particles from inactivation by NaOH. Therefore, appropriate sample preparation of spiking material is important for accurate simulation of the naturally occurring situation. The observed stability at pH 11.8 exceeds the previously reported upper limit of pH 9. Inactivation was due to disintegration of the viral capsid as assessed by accessibility of viral DNA for endonucleases.     

Chlorination of Indicator Bacteria and Viruses in Primary Sewage Effluent

Wastewater disinfection is used in many countries for reducing fecal coliform levels in effluents. Disinfection is therefore frequently used to improve recreational bathing waters which do not comply with microbiological standards. It is unknown whether human enteric viruses (which are responsible for waterborne disease) are simultaneously inactivated alongside fecal coliforms. This laboratory study focused on the chlorination of primary treated effluent with three doses (8, 16, and 30 mg/liter) of free chlorine as sodium hypochlorite. Seeding experiments showed that inactivation (>5 log₁₀ units) of Escherichia coli and Enterococcus faecalis was rapid and complete but that there was poor inactivation (0.2 to 1.0 log₁₀ unit) of F⁺-specific RNA (FRNA) bacteriophage (MS2) (a potential virus indicator) at all three doses. However, seeded poliovirus was significantly more susceptible (2.8 log₁₀ units) to inactivation by chlorine than was the FRNA bacteriophage. To ensure that these results were not artifacts of the seeding process, comparisons were made between inactivation rates of laboratory-seeded organisms in sterilized sewage and inactivation rates of organisms occurring naturally in sewage. Multifactorial analysis of variance showed that there was no significant difference (P > 0.05) between the inactivation rates for seeded and naturally occurring FRNA bacteriophage. However, laboratory-grown poliovirus was inactivated much more rapidly than were naturally occurring, indigenous enteroviruses (P < 0.001). This may reflect differences in the way indigenous virus is presented to the disinfectant. Inactivation rates for indigenous enteroviruses were quite similar to those seen for FRNA bacteriophage at lower doses of chlorine. These results have significance for the effectiveness of chlorination as a sewage treatment process, particularly where virus contamination is of concern, and suggest that FRNA bacteriophage would be an appropriate indicator of such viral inactivation under field conditions.     

Composting for avian influenza virus elimination

Effective sanitization is important in viral epizootic outbreaks to avoid further spread of the pathogen. This study examined thermal inactivation as a sanitizing treatment for manure inoculated with highly pathogenic avian influenza virus H7N1 and bacteriophages MS2 and 6. Rapid inactivation of highly pathogenic avian influenza virus H7N1 was achieved at both mesophilic (35°C) and thermophilic (45 and 55°C) temperatures. Similar inactivation rates were observed for bacteriophage 6, while bacteriophage MS2 proved too thermoresistant to be considered a valuable indicator organism for avian influenza virus during thermal treatments. Guidelines for treatment of litter in the event of emergency composting can be formulated based on the inactivation rates obtained in the study.     

Size and UV Germicidal Irradiation Susceptibility of Serratia marcescens when Aerosolized from Different Suspending Media

Experimental systems have been built in laboratories worldwide to investigate the influence of various environmental parameters on the efficacy of UV germicidal irradiation (UVGI) for deactivating airborne microorganisms. It is generally recognized that data from different laboratories might vary significantly due to differences in systems and experimental conditions. In this study we looked at the effect of the composition of the suspending medium on the size and UVGI susceptibility of Serratia marcescens in an experimental system built in our laboratory. S. marcescens was suspended in (i) distilled water, (ii) phosphate buffer, (iii) 10% fetal calf serum, (iv) phosphate-buffered saline (saline, 0.8% sodium chloride), and (v) synthetic saliva (phosphate-buffered saline with 10% fetal calf serum). At low humidity (36%), S. marcescens suspended in water-only medium was the most susceptible to UVGI, followed by those in serum-only medium. The count median diameters (CMDs) for culturable particles from water-only and serum-only media were 0.88 and 0.95 μm, respectively, with the measurements based on their aerodynamic behavior. The bacteria suspended in phosphate buffer, synthetic saliva, and phosphate-buffered saline had similar UVGI susceptibility and CMD at 1.0, 1.4, and 1.5 μm, respectively. At high humidity (68%) the CMD of the particles increased by 6 to 16%, and at the same time UVGI susceptibility decreased, with the magnitude of decrease related to the type of suspending medium. In conclusion, the choice of suspending medium influenced both size and UVGI susceptibility of S. marcescens. These data are valuable for making comparisons and deciding on the use of an appropriate medium for various applications.     

Loss of adsorptive ability--the reason for inactivation of the RM2 bacteriophage during storage

The kinetics of bacteriophage PM2 inactivation at storage was compared with the kinetics of bacteriophage adsorption on Alteromonas espejiana BAL-31 host cells. Adsorption ability and infectivity are lost with the same rate at temperatures 4-28 degrees C suggesting the loss of adsorption ability to result in bacteriophage inactivation. At higher temperatures infectivity is lost more rapidly than the ability of adsorption. The single hit kinetics of adsorption ability loss suggests the simple model of independent inactivation of 12 antireceptors located at the tops of icosaedric capsid to be erroneous. At bacteriophage inactivation the major port of protein I, a fragment of antireceptors, is preserved in the capsid composition.     

Inactivation of bacteriophage PM2 during storage

The kinetics of bacteriophage inactivation in the medium that is optimal for its storage has been studied at temperatures from 4 to 55 degrees C. The plot of Arrhenius dependence of the constant of inactivation rate consists of the two linear parts with the energies of activation Ea = 25 kcal/mol for 4-37 degrees C and Ea = 91 kcal/mol for 37-55 degrees C. The DNA of inactivated bacteriophage remained mostly in superspiralized form and completely preserved its biological activity as tested by transfection in spheroplasts. The analysis of inactivation kinetics suggests ageing of virions cultivated at 4 degrees C. The addition of watersoluble antioxidant amoxipin did not change the inactivation kinetics. The addition of antioxidant ionol with twin-80 increased the inactivation that was paralleled by the bacteriophage DNA degradation.     

Detection and quantitative determination of abscisic acid by immunological assay

Summary Antibodies with specificity towards abscisic acid (ABA) were produced in rabbits. These antibodies were used for assaying ABA by the inhibition of inactivation of modified bacteriophage. For this assay conjugates of ABA with bacteriophage T₄ were prepared and characterized. Such chemically modified bacteriophages were completely inactivated by the specific anti-ABA serum and this inactivation was inhibited by free ABA. The identification and quantitative determination of ABA in plant extracts by this method are demonstrated and the method is compared with a common bioassay.     

Ultraviolet Inactivation Dichroic Ratio of Oriented fd Bacteriophage

Polarized UV light irradiation of flow-oriented fd bacteriophage indicates that the degree of damage (inactivation) depends on the relative orientation of the light polarization vector and the plane of the DNA bases. The technique of anisotropic UV inactivation was evaluated, and further information on the orientation in this virus was gained. The fd bacteriophage were aligned and irradiated with plane-polarized monochromatic UV light either parallel or perpendicular to the virus axis. Variation of the inactivation dichroic ratio with wavelength implicated virus inactivation by light absorbed in both the DNA and protein. Analysis of the wavelength variation of inactivation dichroic ratios gave molecular dichroic ratios of 0.76 and 1.48 for the DNA and protein components, respectively. On the basis of these anisotropic inactivation studies, the average angle of DNA base tilt in fd was calculated to be 29-32°, a value in agreement with the absorption dichroism studies of Bendet and Mayfield.     

Comparison of the inactivation of Bacillus subtilis spores and MS2 bacteriophage by MIOX, ClorTec and hypochlorite

AIMS: To compare the disinfection ability of two widely used electrolytic generation systems (ClorTec and MIOX) and the conventional chlorine disinfectant (sodium hypochlorite) using three strains of Bacillus subtilis spores and MS2 bacteriophage. METHODS AND RESULTS: Three B. subtilis aerobic spore strains (ATCC1A1, 35021 and 35946) and the bacteriophage MS2 (ATCC 15597-B1) were propagated and sporulated. Four indicator organisms were exposed to four disinfectant treatments for comparing the effectiveness of inactivation: hypochlorite, ClorTec, MIOX and MIOX-anode. The results indicated that the two electrolytic generation systems were as effective as the conventional chlorination for the inactivation of micro-organisms used. Some data points showed the variation using anova analysis, in which the inactivation of MIOX and ClorTec was higher than that of hypochlorite. CONCLUSIONS: The ClorTec and MIOX systems are quite similar to hypochlorite in the inactivation-effectiveness for aerobic spores and bacteriophage in drinking water. SIGNIFICANCE AND IMPACT OF THE STUDY: Laboratory-scale investigation proved that gaseous chlorine could be replaced by either ClorTec or MIOX systems for the drinking water treatment utilities, which still could maintain the same disinfection efficiency.     

The role of bivalent ions in the inactivation of bacteriophage phi X174 by lipopolysaccharide from Escherichia coli C.

The need for Ca2+ in the inactivation of bacteriophage phi X174 by lipopolysaccharide from Escherichia coli C was confirmed. Ca2+ could be replaced almost completely by Na+, but the concentration of Na+ needed was greater by more than an order of magnitude. Other bivalent ions caused inactivation in the same way as Ca2+, and the degree of inactivation varied according to the ion. At 50% inactivation of bacteriophage, the relation between the concentrations of NaCl and of bivalent or tervalent ions (Mx+) fitted the conception that NaCl was neutralizing electrostatic repulsion between virus and lipopolysaccharide by an ionic-strength effect: that is, log[Mx+] varies inversely with square root[NaCl]. The variation in effect of bi- and ter-valent ions and the low concentration needed show that this is not an ionic-strength effect but likely to involve binding to more than one site.     

Photocatalytic antimicrobial activity of thin surface films of TiO(2), CuO and TiO (2)/CuO dual layers on Escherichia coli and bacteriophage T4

TiO₂-coated surfaces are increasingly studied for their ability to inactivate microorganisms. The activity of glass coated with thin films of TiO₂, CuO and hybrid CuO/TiO₂ prepared by atmospheric Chemical Vapour Deposition (Ap-CVD) and TiO₂ prepared by a sol–gel process was investigated using the inactivation of bacteriophage T4 as a model for inactivation of viruses. The chemical oxidising activity was also determined by measuring stearic acid oxidation. The results showed that the rate of inactivation of bacteriophage T4 increased with increasing chemical oxidising activity with the maximum rate obtained on highly active sol–gel preparations. However, these were delicate and easily damaged unlike the Ap-CVD coatings. Inactivation rates were highest on CuO and CuO/TiO₂ which had the lowest chemical oxidising activities. The inactivation of T4 was higher than that of Escherichia coli on low activity surfaces. The combination of photocatalysis and toxicity of copper acted synergistically to inactivate bacteriophage T4 and retained some self-cleaning activity. The presence of phosphate ions slowed inactivation but NaCl had no effect. The results show that TiO₂/CuO coated surfaces are highly antiviral and may have applications in the food and healthcare industries.     

The interaction of platinum II compounds with bacteriophages T7 and R17

The inactivation of the DNA-containing bacteriophage T7 and of the RNA-containing bacteriophage R17 by dichloro-ethylenediamine Pt II and by cis- and trans-dichloro-diammine Pt II has been studied under a variety of experimental conditions. It has been found that the mean lethal concentrations vary for T7 from 0.007 to 0.5 μg/ml and for R17 from 0.09 to 1.1 μg/ml depending upon which compound is used and the manner in which the experiment is performed. Experiments with the ¹⁴C-labelled ethylenediamine derivative have shown that inactivation is primarily related to the extent of reaction of the compound with the bacteriophage and that variations in inactivation observed under different experimental conditions simply reflect differences in the kinetics of the binding reactions. Quantitative comparisons have shown that at the mean lethal dose 1.5 molecules of platinum compound are bound to each R17 bacteriophage and 5 molecules to each T7.96% of the compound bound to R17 was bound to RNA and 76% of the compound bound to T7 was bound to the DNA.