Simultaneous Saccharification and Fermentation of Hydrothermal Pretreated Lignocellulosic Biomass: Evaluation of Process Performance Under Multiple Stress Conditions

Industrial lignocellulosic bioethanol processes are exposed to different environmental stresses (such as inhibitor compounds, high temperature, and high solid loadings). In this study, a systematic approach was followed where the liquid and solid fractions were mixed to evaluate the influence of varied solid loadings, and different percentages of liquor were used as liquid fraction to determine inhibitor effect. Ethanol production by simultaneous saccharification and fermentation (SSF) of hydrothermally pretreated Eucalyptus globulus wood (EGW) was studied under combined diverse stress operating conditions (30–38 °C, 60–80 g of liquor from hydrothermal treatment or autohydrolysis (containing inhibitor compounds)/100 g of liquid and liquid to solid ratio between 4 and 6.4 g liquid in SSF/g unwashed pretreated EGW) using an industrial Saccharomyces cerevisiae strain supplemented with low-cost byproducts derived from agro-food industry. Evaluation of these variables revealed that the combination of temperature and higher solid loadings was the most significant variable affecting final ethanol concentration and cellulose to ethanol conversion, whereas solid and autohydrolysis liquor loadings had the most significant impact on ethanol productivity. After optimization, an ethanol concentration of 54 g/L (corresponding to 85 % of conversion and 0.51 g/Lh of productivity at 96 h) was obtained at 37 °C using 60 % of autohydrolysis liquor and 16 % solid loading (liquid to solid ratio of 6.4 g/g). The selection of a suitable strain along with nutritional supplementation enabled to produce noticeable ethanol titers in quite restrictive SSF operating conditions, which can reduce operating cost and boost the economic feasibility of lignocellulose-to-ethanol processes.     

Inoculation effect of thermophilic microorganisms on protease production through solid-state fermentation under non-sterile conditions at lab and bench scale (SSF)

The production of protease enzyme was evaluated through the solid state fermentation (SSF) of soy fibre, a waste product that acted as a sole substrate for the fermentation, at a laboratory and bench scale using a 500-mL (batch size 115 g) and 10-L (batch size 2300 g) bioreactors. The objective was to assess the effect of the inoculation of the thermophilic bacteria Thermus sp. on the production of the enzyme when working at laboratory and bench scale under non-sterile conditions, since scaling-up and the need of sterilization are the main challenges of SSF, preventing its industrial development. Results revealed that the inoculation led to a substantial increase in the protease obtained on both scales when compared to non-inoculated fermentation. The maximum protease activities increased as a result of the inoculation from 500 to 800 and from 350 to 670 U/g dry matter of soy fibre in the lab and bench scale bioreactors, respectively. Finally, a very good correlation was found between the protease activities obtained and the fermentation most relevant parameters: oxygen uptake rate (R ² = 0.81) and temperature (R ² = 0.82). In this work, we have demonstrated that inoculation is effective even under non-sterile conditions at the kg scale and that this strain is able to compete with autochthonous microbiota and increase the protease production to levels higher than those previously reported in literature.     

Production and Regulation of Lipase Activity from <Emphasis Type="Italic">Penicillium restrictum</Emphasis> in Submerged and Solid-State Fermentations

Different carbon (C) sources, mainly carbohydrates and lipids, have been screened for their capacity to support growth and lipase production by Penicillium restrictum in submerged fermentation (SmF) and in solid-state fermentation (SSF). Completely different physiological behaviors were observed after the addition of easily (oleic acid and glucose) and complex (olive oil and starch) assimilable C sources to the liquid and solid media. Maximal lipolytic activities (12.1 U/mL and 17.4 U/g) by P. restrictum were obtained with olive oil in SmF and in SSF, respectively. Biomass levels in SmF (12.2–14.1 mg/mL) and SSF (7.0–8.0 mg/g) did not varied greatly with the distinct C sources used. High lipase production (12.3 U/g) using glucose was only attained in SSF, perhaps due to the ability of this fermentation process to minimize catabolite repression.     

Lactic acid and animal feeds production from Sophora flavescens residues by Rhizopus oryzae fermentation

In this study, the feasibility of producing lactic acid and animal feeds from Sophora flavescens residues (SFR) by Rhizopus oryzae was explored. Results showed that the simultaneous saccharification and fermentation (SSF) is the optimal fermentation mode, which was simple and high-efficiency. When the inoculation volume of R. oryzae was 10 % and the pH value was adjusted by adding CaCO₃ in stages during SSF, the maximum concentration of lactic acid was 46.78 g/L, and the maximum lactic acid productivity reached 0.97 g/L/h. Results also showed that the protein content of the solid residues after fermentation of R. oryzae reached 12.15 %. This content was 46 times higher than that by the original SFRs and nearly 4.3 times the protein content of the solid residues after fermentation by Enterococcus faecium. In addition, the solid residues after fermentation rich in Fe and Zn could be used as animal feeds or feed additives. Thus, it is expected that this study may provide a novel approach for Chinese medicine residues treatment towards full resource recovery.     

Solid state fermentation for cellulases and β-glucosidase production by Aspergillus niger

Production of cellulases and β-glucosidase was studied using locally-isolated Aspergillus niger on various cheap sources of cellulose like bagasse, corn corbs, computer cards and sawdust, by solid state fermentation (SSF) and by liquid state fermentation (LSF). Enzyme activities were increased about 30–80% by SSF in comparison with conventional LSF. Enzyme production was further improved by various pretreatments, making cellulosic material easily accessible. The best results were obtained with 5 M NaOH treatment.     

Comparative study of protease production in solid substrate fermentation versus submerged fermentation

Attempts have been made to compare solid substrate fermentation (SSF) with submerged fermentation for the production of proteases by Bacillus amyloliquefaciens. In submerged fermentation it produced 800,000 units of enzyme under optimal conditions in a 20-litre fermentor whereas in solid substrate, it produced 250,000 units/g. Owing to the simplicity and easiness of operation of SSF and for applications like unhairing, biodetergents and bating the former would be advantageous for the production of proteases.     

Exoglucanase production by Aspergillus niger grown on wheat bran

β-Exoglucanase production on the lignocellulosic material, wheat bran, by Aspergillus niger under solid state fermentation (SSF) on a laboratory scale was investigated. Different fermentation parameters, such as moisture content, initial pH, temperature, depth of the substrate, and inoculum size on exoglucanase production were optimized. Moisture content of 40 %, pH of 7.0, substrate depth of 1.0 cm, inoculum size of 2?×?10⁶ spores/g of wheat bran, and temperature at 30 °C were optimal for maximum production of exoglucanase. Maximum yields of exoglucanase with 28.60 FPU/g of wheat bran were obtained within 3 days of incubation under optimal conditions.     

Influence of pH regulation and nutrient content on cephalosporin C production in solid-state fermentation by Acremonium chrysogenum C10

Aims: To investigate the effect of pH regulation and nutrient concentration on cephalosporin C (CPC) production in solid‐state fermentation (SSF), using sugarcane bagasse as inert support, impregnated with liquid medium. Methods and Results: Solid‐state fermentation using different initial pH values, buffer and nutrient concentrations were performed. Results revealed pH as a key parameter in CPC SSF, as it hampered the antibiotic production not only above 7·8, but also under 6·4. Using initial pH lower than 6·8 and PB in the solid medium, it was possible to keep pH within the production range, increase the production period (from 1 to 3 days) and hence the CPC yield from 468 to 3200 μg gdm^?1 (g^?1 of dry matter). Conclusion: Parameters that help to keep pH in adequate values for CPC production in SSF, such as initial pH, buffering system and nutrient concentration, can greatly increase the production time and CPC yields in this fermentation technique. Significance and Impact of the Study: This is the first work on CPC production on impregnated support, and the only one revealing pH as a key parameter; it is also shown that high nutrient concentration can improve CPC yields in SSF as long as pH is kept under control.     

以玉米秸秆为原料同步糖化发酵生产燃料乙醇

以玉米秸秆为原料,经酸法预处理后,采用同步糖化发酵SSF工艺生产燃料乙醇。正交试验获得的最佳体系为:培养温度34℃、发酵pH值5.5、发酵的液固比8:1、当发酵108h后,乙醇浓度可达8.33g/L。该实验为纤维质燃料乙醇的产业化生产提供技术依据。     

Enzymatic hydrolysis and simultaneous saccharification and fermentation of alkali/peracetic acid-pretreated sugarcane bagasse for ethanol and 2,3-butanediol production

The enzymatic digestibility of alkali/peracetic acid (PAA)-pretreated bagasse was systematically investigated. The effects of initial solid consistency, cellulase loading and addition of supplemental β-glucosidase on the enzymatic conversion of glycan were studied. It was found the alkali-PAA pulp showed excellent enzymatic digestibility. The enzymatic glycan conversion could reach about 80% after 24 h incubation when enzyme loading was 10 FPU/g solid. Simultaneous saccharification and fermentation (SSF) results indicated that the pulp could be well converted to ethanol. Compared with dilute acid pretreated bagasse (DAPB), alkali-PAA pulp could obtain much higher ethanol and xylose concentrations. The fermentation broth still showed some cellulase activity so that the fed pulp could be further converted to sugars and ethanol. After the second batch SSF, the fermentation broth of alkali-PAA pulp still kept about 50% of initial cellulase activity. However, only 21% of initial cellulase activity was kept in the fermentation broth of DAPB. The xylose syrup obtained in SSF of alkali-PAA pulp could be well converted to 2,3-butanediol by Klebsiella pneumoniae CGMCC 1.9131.     

Solid substrate fermentation of wheat straw to fungal protein

Steam-treated wheat straw at a 70% (w/w) moisture level was subjected to solid substrate fermentation (SSF) with Trichoderma reesei (Riga, USSR) or a mixed culture of T. reesei and Endomycopsis fibuliger (R-574) in fermentation equipment of various design: some with mixing, some with stationary layers, including a mixedlayer 1.5-m(3) pilot plant scale fermenter. The best protein productivity was obtained in stationary layer fermenters with a product containing 13% protein. The main limitations of lignocellulose SSF, such as hindrance of fungal growth, limiting accessibility and availability of substrate, and difficulty in moisture and heat control, were analyzed. The technological parameters of SSF, submerged fermentation, and alternate lignocellulose conversion processes were compared. The SSF had lower overall efficiency but higher product concentration per reaction volume than other conversion schemes.     

A comparison between simultaneous saccharification and fermentation and separate hydrolysis and fermentation using steam-pretreated corn stover

Two different process configurations, simultaneous saccharification and fermentation (SSF) and separate hydrolysis and fermentation (SHF), were compared, at 8% water-insoluble solids (WIS), regarding ethanol production from steam-pretreated corn stover. The enzymatic loading in these experiments was 10 FPU/g WIS and the yeast concentration in SSF was 1 g/L (dry weight) of a Saccharomyces cerevisiae strain. When the whole slurry from the pretreatment stage was used as it was, diluted to 8% WIS with water and pH adjusted, SSF gave a 13% higher overall ethanol yield than SHF (72.4% versus 59.1% of the theoretical). The impact of the inhibitory compounds in the liquid fraction of the pretreated slurry was shown to affect SSF and SHF in different ways. The overall ethanol yield (based on the untreated raw material) decreased when SSF was run in absence on inhibitors compared to SSF with inhibitors present. On the contrary, the presence of inhibitors decreased the overall ethanol yield in the case of SHF. However, the SHF yield achieves in the absence of inhibitors was still lower than the SSF yield achieves with inhibitors present.     

Production of the antifungal peptide antibiotic,iturin by Bacillus subtilis NB22 in solid state fermentation

Production of iturin, an antifungal peptide effective at suppressing phytopathogens, by Bacillus subtilis NB22 was investigated in solid state fermentation (SSF) using soy bean curd residue (okara). In scale-up from 15 g to 3 kg, aeration, temperature, and moisture content were controlling factors for the efficient production of iturin. It was found that solid state fermentation was 6–8 times more efficient with respect to iturin productivity than submerged fermentation on the basis of unit wet weight. Higher productivity in selective production of specific components of iturin which are stronger inhibitors of plant pathogens was also confirmed in SSF.     

Development of high penicillin producing strains for solid state fermentation

Penicillin production with an industrial strain and 4 strains of P. chrysogenum, in solid state fermentation (SSF) and liquid submerged fermentation (LSF), was determined. Their ability to produce the antibiotic in SSF in relation to their capacity to do so in LSF was evaluated. this was done by calculating the ratio PS/PL (production in SSF/production in LSF), which was called relative production. Clones were isolated from each strain and evaluated in a similar way. The strains presented different relative productions (from 1.4 to 2.5). Within the clones, a much wider range of relative productions was observed (0.6 to 16.7). On the other hand, the highest-producing strains in LSF were also the highest producers in SSF. This indicates that the production potential of a strain is an important factor in its production level in SSF. Moreover, the highest penicillin producing ciones (9,500 to 10,500 microg of penicillin/g were generated from high-yielding strains (P2 and ASP-78). However, the higher-producing strains (in LSF) showed lower relative performance, suggesting that higher producing strains tend to express less efficiently their potential in SSF. In this study, several overproducing clones, particularly suited for SSF, were obtained by the procedures followed. Production increases of 500 to 600 %, in this culture system, were achieved.     

Alkaline protease from Thermoactinomyces sp. RS1 mitigates industrial pollution

Proteases have found a wide application in the several industrial processes, such as laundry detergents, protein recovery or solubilization, prion degradation, meat tenderizations, and in bating of hides and skins in leather industries. But the main hurdle in industrial application of proteases is their economical production on a large scale. The present investigation aimed to exploit the locally available inexpensive agricultural and household wastes for alkaline protease production using Thermoactinomyces sp. RS1 via solid-state fermentation (SSF) technique. The alkaline enzyme is potentially useful as an additive in commercial detergents to mitigate pollution load due to extensive use of caustic soda-based detergents. Thermoactinomyces sp. RS1 showed good protease production under SSF conditions of 55 °C, pH 9, and 50 % moisture content with potato peels as solid substrate. The presented findings revealed that crude alkaline protease produced by Thermoactinomyces sp. RS1 via SSF is of potential application in silver recovery from used X-ray films.     

Citric acid production by solid state fermentation using sugarcane bagasse

A solid state fermentation (SSF) method was used to produce citric acid by Aspergillus niger DS 1 using sugarcane bagasse as a carrier and sucrose or molasses based medium as a moistening agent. Initially bagasse and wheat bran were compared as carrier. Bagasse was the most suitable carrier, as it did not show agglomeration after moistening with medium, resulting in better heat and mass transfer during fermentation and higher product yield. Different parameters such as moisture content, particle size, sugar level and methanol concentration of the medium were optimised and 75% moisture level, 31.8 g sugar/100 g dry solid, 4% (v/w) methanol and particles of the size between 1.2 and 1.6 mm were found to be optimal. Sucrose and clarified and non-clarified molasses medium were also tested as moistening agents for SSF and under optimised conditions, 20.2, 19.8 and 17.9 g citric acid /100 g of dry solid with yield of 69.6, 64.5 and 62.4% (based on sugar consumed) was obtained in sucrose, clarified and non-clarified molasses medium respectively, after 9 days of fermentation.     

Biotechnological advantages of laboratory-scale solid-state fermentation with fungi

Despite the increasing number of publications dealing with solid-state (substrate) fermentation (SSF) it is very difficult to draw general conclusion from the data presented. This is due to the lack of proper standardisation that would allow objective comparison with other processes. Research work has so far focused on the general applicability of SSF for the production of enzymes, metabolites and spores, in that many different solid substrates (agricultural waste) have been combined with many different fungi and the productivity of each fermentation reported. On a gram bench-scale SSF appears to be superior to submerged fermentation technology (SmF) in several aspects. However, SSF up-scaling, necessary for use on an industrial scale, raises severe engineering problems due to the build-up of temperature, pH, O₂, substrate and moisture gradients. Hence, most published reviews also focus on progress towards industrial engineering. The role of the physiological and genetic properties of the microorganisms used during growth on solid substrates compared with aqueous solutions has so far been all but neglected, despite the fact that it may be the microbiology that makes SSF advantageous against the SmF biotechnology. This review will focus on research work allowing comparison of the specific biological particulars of enzyme, metabolite and/or spore production in SSF and in SmF. In these respects, SSF appears to possess several biotechnological advantages, though at present on a laboratory scale only, such as higher fermentation productivity, higher end-concentration of products, higher product stability, lower catabolic repression, cultivation of microorganisms specialized for water-insoluble substrates or mixed cultivation of various fungi, and last but not least, lower demand on sterility due to the low water activity used in SSF.     

Simultaneous saccharification and fermentation of lignocellulosic residues pretreated with phosphoric acid–acetone for bioethanol production

Bermudagrass, reed and rapeseed were pretreated with phosphoric acid–acetone and used for ethanol production by means of simultaneous saccharification and fermentation (SSF) with a batch and fed-batch mode. When the batch SSF experiments were conducted in a 3% low effective cellulose, about 16 g/L of ethanol were obtained after 96 h of fermentation. When batch SSF experiments were conducted with a higher cellulose content (10% effective cellulose for reed and bermudagrass and 5% for rapeseed), higher ethanol concentrations and yields (of more than 93%) were obtained. The fed-batch SSF strategy was adopted to increase the ethanol concentration further. When a higher water-insoluble solid (up to 36%) was applied, the ethanol concentration reached 56 g/L of an inhibitory concentration of the yeast strain used in this study at 38 °C. The results show that the pretreated materials can be used as good feedstocks for bioethanol production, and that the phosphoric acid–acetone pretreatment can effectively yield a higher ethanol concentration.     

Ethanol production from wheat straw by recombinant Escherichia coli strain FBR5 at high solid loading

Ethanol production by a recombinant bacterium from wheat straw (WS) at high solid loading by separate hydrolysis and fermentation (SHF) and simultaneous saccharification and fermentation (SSF) was studied. The yield of total sugars from dilute acid pretreated WS (150 g/L) after enzymatic saccharification was 86.3 ± 1.5 g/L. The pretreated WS was bio-abated by growing a fungal strain aerobically in the liquid portion for 16 h. The recombinant Escherichia coli strain FBR5 produced 41.1 ± 1.1 g ethanol/L from non-abated WS hydrolyzate (total sugars, 86.6 ± 0.3 g/L) in 168 h at pH 7.0 and 35 °C. The bacterium produced 41.8 ± 0.0 g ethanol/L in 120 h from the bioabated WS by SHF. It produced 41.6 ± 0.7 g ethanol/L in 120 h from bioabated WS by fed-batch SSF. This is the first report of the production of above 4% ethanol from a lignocellulosic hydrolyzate by the recombinant bacterium.     

Comparative production of cellulases by mutants of Penicillium janthinellum NCIM 1171 and its application in hydrolysis of Avicel and cellulose

Mutants of Penicillium janthinellum NCIM 1171 were evaluated for cellulase production using both submerged fermentation (SmF) and solid state fermentation (SSF). Mutant EU2D-21 gave highest yields of cellulases in both SmF and SSF. Hydrolysis of Avicel and cellulose were compared using SmF and SSF derived enzyme preparations obtained from EU2D-21. Surprisingly, the use of SSF derived preparation gave less hydrolysis compared to SmF derived enzymes. This may be due to inactivation of β-glucosidase at 50 °C in SSF derived enzyme preparations. SmF derived enzyme preparations contained both thermostable and thermosensitive β-glucosidases where as SSF derived enzyme preparations contained predominantly thermosensitive β-glucosidase. This is the first report on less thermostability of SSF derived β-glucosidase which is the main reason for getting less hydrolysis.