固定化乳酸乳球菌连续生产Nisin的研究

以海藻酸钙为材料 ,固定乳酸乳球菌 (Lactococcuslactissubsp .lactis)SM5 2 6 ,研究不同条件对Nisin合成的影响。结果表明 ,利用 2 %海藻酸钠在 1 0mmol LCaCl2 条件下 ,得到的固定化细胞颗粒稳定性较好 ,可维持 90h无破裂 ;在发酵过程中SYS3培养基中的无机盐成分尤其磷酸盐对固定化颗粒有破坏作用 ;用mSYS3培养基代替SYS3 ,通过 72h三批次循环的半连续培养 ,Nisin活性为 85 0IU mL ,无明显的细胞渗漏现象。连续化生产 70h ,Nisin活性达 1 1 5 0IU mL ,相当于游离细胞的发酵水平。     

Enhancing gas-liquid mass transfer rates in non-newtonian fermentations by confining mycelial growth to microbeads in a bubble column

The performance of a penicillin fermentation was assessed in a laboratory-scale bubble column fermentor, with mycelial growth confined to the pore matrix of celite beads. Final cell densities of 29 g/L and penicillin titres of 5.5 g/L were obtained in the confined cell cultures. In comparison, cultures of free mycelial cells grown in the absence of beads experienced dissolved oxygen limitations in the bubble column, giving only 17 g/L final cell concentrations with equally low penicillin titres of 2 g/L. The better performance of the confined cell cultures was attributed to enhanced gas liquid mass transfer rates, with mass transfer coefficients (k(L)a) two to three times higher than those determined in the free cell cultures. Furthermore, the confined cell cultures showed more efficient utilization of power input for mass transfer, providing up to 50% reduction in energy requirements for aeration.     

Production of l (+) lactic acid by Lactobacillus delbrueckii immobilized in functionalized alginate matrices

The role of functionalized alginate gels as immobilized matrices in production of l (+) lactic acid by Lactobacillus delbrueckii was studied. L. delbrueckii cells immobilized in functionalized alginate beads showed enhanced bead stability and selectivity towards production of optically pure l (+) lactic acid in higher yields (1.74Yp/s) compared to natural alginate. Palmitoylated alginate beads revealed 99% enantiomeric selectivity (ee) in production of l (+) lactic acid. Metabolite analysis during fermentation indicated low by-product (acetic acid, propionic acid and ethanol) formation on repeated batch fermentation with functionalized immobilized microbial cells. The scanning electron microscopic studies showed dense entrapped microbial cell biomass in modified immobilized beads compared to native alginate. Thus the methodology has great importance in large-scale production of optically pure lactic acid.     

The production of ethanol by immobilized yeast cells

Saccharomyces cerevisiae cells were immobilized in calcium alginate beads for use in the continuous production of ethanol. Yeasts were grown in medium supplemented with ethanol to selectively screen for a culture which showed the greatest tolerance to ethanol inhibition. Yeast beads were produced from a yeast slurry containing 1.5% alginate (w/v) which was added as drops to 0.05M CaCl₂ solution. To determine their optimum fermentation parameters, ethanol production using glucose as a substrate was monitored in batch systems at varying physiological conditions (temperature, pH, ethanol concentration), cell densities, and gel concentration. The data obtained were compared to optimum free cell ethanol fermentation parameters. The immobilized yeast cells examined in a packed-bed reactor system operated under optimized parameters derived from batch-immobilized yeast cell experiments. Ethanol production rates, as well as residual sugar concentration were monitored at different feedstock flow rates.     

Enhancement and stabilization of the production of glucoamylase by immobilized cells of Aureobasidium pullulans in a fluidized-bed reactor

Summary Glucoamylase production by Aureobasidium pollulans A-124 was compared in free-living cells, cells immobilized in calcium alginate gel beads aerated on a rotary shaker (agitation rate 150 rpm), and immobilized cells aerated in an air bubble column reactor. Fermentation conditions in the bioreactor were established for bead concentration, substrate (starch) concentration, calcium chloride addition to the fermentation medium, and rate of aeration. Production of glucoamylase was optimized at approximately 1.5 units of enzyme activity/ml medium in the bioreactor under the following conditions: aeration rate, 2.0 vol air per working volume of the bioreactor (280 ml) per minute; gel bead concentration, 30% of the working volume; substrate (starch) concentration, at 0.3% (w/v); addition of calcium chloride to the medium at a final concentration of 0.01 M. Productivity levels were stabilized through the equivalent of ten batches of medium with the original inoculum of immobilized beads. Offprint requests to: M. Petruccioli     

Production of dextransucrase by Leuconostoc mesenteroides immobilized in calcium-alginate beads: I. Batch and fed-batch fermentations

In batch fermentation Leuconostoc mesenteroides immobilized in calcium alginate beads produced a total dextransucrase activity equal to about 93% of that by free, suspended bacterial cells under comparable conditions in a bubble column reactor. Continuous sucrose feeding (5 g/L h) to the immobilized-cell culture in the airlift bioreactor increased production of enzymatic activity by about 107% compared with ordinary batch operation of this reactor. About 14% of the enzymatic activity produced by the immobilized cells appears as soluble activity in the cell-free broth compared with about 40% in case of free cells. In an airlift bioreactor, both the soluble and the intact (sorbed and entrapped) enzymatic activity produced by the immobilized bacterial cells was about 34% greater under automatic pH control, compared to that produced in a bubble column reactor with only manual pH control. During formation of dextran by intact enzyme within cells and beads, declines are observed in apparent enzymatic activity.     

Production of thermostable and neutral glucoamylase using immobilized <Emphasis Type="Italic">Thermomucor indicae-seudaticae</Emphasis>

Thermomucor indicae-seudaticae was immobilized in alginate, κ-carrageenan, agarose, agar, polyacrylamide and loofah (Luffa cylindrica) sponge (as such or coated with alginate/starch/Emerson YpSs agar), and used for the production of glucoamylase in submerged fermentation. The mycelium developed from alginate-immobilized sporangiospores secreted higher glucoamylase titres (22.7 U ml⁻¹) than those immobilized in other gel matrices and the freely growing mycelial pellets (18.5 U ml⁻¹). Loofah network provided a good support for mycelial growth, but the enzyme production was lower than that attained with alginate beads. Glucoamylase production increased with inoculum density and the optimum levels were achieved when 40 calcium alginate beads (∼5 × 10⁶ immobilized spores) were used to inoculate 50 ml production medium. The alginate bead inoculum displayed high storage stability at 4°C and produced comparable enzyme titres up to 120 days. The glucoamylase production by hyphae emerged from the immobilized sporangiospores was almost stable over eight batches of repeated fermentation. Scanning electron micrographs of alginate beads, after batch fermentation, revealed extensive mycelial growth inside and around the beads.     

Itaconic acid production by immobilizedAspergillus terreus from xylose and glucose

Summary Aspergillus terreus NRRC 1960 spores were entrapped in calcium alginate gel beads or alternotely the fungal mycelium was immobilized either on Celite R-626 or in agar gel cubes, and the biocatalyst was employed both in repeated batch and in continuous column reactors to produce itaconic acid from D-xylose or D-glucose. The highest itaconic acid yield obtained in a submerged culture batch fermentation was 54.5% based on total initial glucose (55 g/l) with a volumetric productivity of 0.32 g/l h, and 44.8% from xylose (67 g/l) with a productivity of 0.20 g/l h. In a repeated batch fermentation mycelium immobilized in agar gel had a productivity of 0.112 g/l h, and mycelium grown from spores immobilized in calcium alginate gel 0.06 g/l h, both from xylose (60 g/l). With the best immobilized biocatalyst system used employing Celite R-626 as a carrier, volumetric productivities of 1.2 g/l h from glucose and 0.56 g/l h from xylose (both at 60 g/l) were obtained in continuous column operation for more than 2 weeks.     

Rheological properties of chromosomal and plasmid DNA during alkaline lysis reaction

The experimental apparatus for the simultaneous L-lactic acid fermentation by Rhizopus oryzae immobilized in calcium alginate beads and product separation process was set up in which a three-phase fluidized-bed bioreactor was used as a fermentor and an external electrodialyzer as a separator, and a pump was applied to recycle the fermentation broth between the bioreactor and the separator. The L-lactic acid produced in the fermentor was separated in the separator, product inhibition was alleviated without any addition of alkali or alkali salts and the product purification process could be simplified. The specific productivity and the yield in electrodialysis fermentation (ED-F) process operated in continuous feeding mode were almost the same as that in CaCO₃-buffered fermentation process. A mathematical model of L-lactic acid production in ED-F process was also suggested, in which the model equations for the bioreactor and the electrodialyzer were combined to describe the simultaneous fermentation and product separation. The model predictions were in good agreement with the experimental data.     

Enhancement of penicillin acylase activity by cultivating immobilized Kluyvera citrophila

Summary Whole cells of Kluyvera citrophila were immobilized in polyacrylamide gel. The penicillin acylase activity of immobilized whole cells was 60%–70% of native cells. When the immobilized cells were continuously cultivated for 40 h in an aerated fermentor containing peptone medium and were treated with alkali in order to remove -lactamase activity, the immobilized cells produced ampicillin up to 4.4 times faster than noncultivated cells.Ampicillin production was investigated in a column system using these cultivated immobilized whole cells. The cultivated immobilized cells showed excellent performance in continuous ampicillin production.     

Determination of the intrinsic fermentation kinetics of Saccharomyces cerevisiae cells immobilized in Ca-alginate beads and observations on their growth

Continuous fermentation experiments in a well-stirred fermentor with Saccharomyces cerevisiae cells immobilized in Ca-alginate beads of small diameter (approx. 1 mm) have been performed in order to discover their intrinsic fermentation kinetics, and compare them to the fermentation kinetics for free cells, by fitting both sets of results to the same model. The results show similar kinetic parameters for free and immobilized cells. The changes in cell concentration inside the beads and microscopical observations of transverse sections throughout the experiments, allowed discernment of two different scenarios of cell growth inside the beads: low cell density and fully developed growth. Correspondence to: F. Gòdia     

Growth and morphology of thermophilic dairy starters in alginate beads

The aim of this research was to produce concentrated biomasses of thermophilic lactic starters using immobilized cell technology (ICT). Fermentations were carried out in milk using pH control with cells microentrapped in alginate beads. In the ICT fermentations, beads represented 17% of the weight. Some assays were carried out with free cells without pH control, in order to compare the ICT populations with those of classical starters. With Streptococcus thermophilus, overall populations in the fermentor were similar, but maximum bead population for (8.2 x 10(9) cfu/g beads) was 13 times higher than that obtained in a traditional starter (4.9 x 10(8) cfu/ml). For both Lactobacillus helveticus strains studied, immobilized-cell populations were about 3 x 10(9) cfu/g beads. Production of immobilized Lb. bulgaricus 210R strain was not possible, since no increases in viable counts occurred in beads. Therefore, production of concentrated cell suspension in alginate beads was more effective for S. thermophilus. Photomicrographs of cells in alginate beads demonstrated that, while the morphology of S. thermophilus remained unchanged during the ICT fermentation, immobilized cells of Lb. helveticus appeared wider. In addition, cells of Lb. bulgaricus were curved and elongated. These morphological changes would also impair the growth of immobilized lactobacilli.     

Production of xylanase by immobilized Trichoderma reesei SAF3 in Ca-alginate beads

In the present study, the optimum conditions for the production of xylanase by immobilized spores of Trichoderma reesei SAF3 in calcium alginate beads were determined. The operational stability of the beads during xylanase production under semi-continuous fermentation was also studied. The influence of alginate concentration (1, 2, 3, and 4%) and initial cell loading (100, 200, 300, 400, and 500 beads per flask) on xylanase production was considered. The production of xylanase was found to increase significantly with increasing concentration of alginate and reached a maximum yield of 3.12 ± 0.18 U ml⁻¹ at 2% (w/v). The immobilized cells produced xylanase consistently up to 10 cycles and reached a maximum level at the forth cycle (3.36 ± 0.2 U ml⁻¹).     

Immobilization of Bacillus amyloliquefaciens MBL27 cells for enhanced antimicrobial protein production using calcium alginate beads

Cell immobilization is one of the common techniques for increasing the overall cell concentration and productivity. Bacillus amyloliquefaciens MBL27 cells were immobilized in calcium alginate beads and it is a promising method for repeated AMP (antimicrobial protein) production. The present study aimed at determining the optimal conditions for immobilization of B. amyloliquefaciens MBL27 cells in calcium alginate beads and the operational stability for enhanced production of the AMP. AMP production with free and immobilized cells was also done. In batch fermentation, maximum AMP production (7300 AU (arbitrary units)/ml against Staphylococcus aureus) was obtained with immobilized cells in shake flasks under optimized parameters such as 3% (w/v) sodium alginate, 136?mM CaCl2 with 350 alginate beads/flask of 2.7-3.0?mm diameter. In repeated cultivation, the highest activity was obtained after the second cycle of use and approx. 94% production was noted up to the fifth cycle. The immobilized cells of B. amyloliquefaciens MBL27 in alginate beads are more efficient for the production of AMP and had good stability. The potential application of AMP as a wound healant and the need for development of economical methods for improved production make whole cell immobilization an excellent alternative method for enhanced AMP production.     

Morphology of Penicillium chrysogenum strains immobilized in calcium alginate beads and used in penicillin fermentation

Summary The morphology of two strains of Penicillium chrysogenum immobilized in calcium alginate and used in penicillin fermentation was examined. The degree and distribution of mycelial growth inside and on the surface of the beads depended on the strain, the cultivation media and the fermentation time. P. chrysogenum ATCC 12690 developed as a mycelial network inside the beads. The growth tendency of P. chrysogenum S₁ in micropellets was directed to the outer surface of the beads. At the end of the production phase only a trace of mycelia and no micropellets in the center of alginate beads were observed, while the outer surface and the subsurface were completely covered with mycelia.     

Continuous ethanol fermentation using immobilized yeast cells

Growing cells of Saccharomyces cerevisiae immobilized in calcium alginate gel beads were employed in fluidizedbed reactors for continuous ethanol fermentation from cane molasses and other sugar sources. Some improvements were made in order to avoid microbial contamination and keep cell viability for stable long run operations. Notably, entrapment of sterol and unsaturated fatty acid into immobilized gel beads enhanced ethanol productivity more than 50 g ethanol/L gel h and prolonged life stability for more than one-half year. Cell concentration in the carrier was estimated over 250 g dry cell/L gel. A pilot plant with a total column volume of 4 kL was constructed and has been operated since 1982. As a result, it was confirmed that 8-10%(v/v)ethanol-containing broth was continuously produced from nonsterilized diluted cane molasses for over one-half year. The productivity of ethanol was calculated as 0.6 kL ethanol/kL reactor volume day with a 95% conversion yield versus the maximum theoretical yield for the case of 8.5% (v/v) ethanol broth.     

Ethanol production from whey with immobilized living yeast

Summary Living Kluyveromyces fragilis yeast cells were succesfully entrapped in calcium alginate gel beads at cell loadings of 4 to 16 g yeast (0.8 to 3.2 g d.m.) per 1 g of sodium alginate. In batch systems, about 90 % conversion in 48 h was obtained both with free and immobilized yeast using demineralized whey of 5 to 10 % lactose content as substrate. In continuous packed-bed column operation nearly a constant 2 % product ethanol concentration could be maintained at 5 % substrate lactose level for at least one month.     

Chlortetracycline production with immobilized Streptomyces aureofaciens

Summary The semicontinuous production of chlortetracycline by immobilized cells of Streptomyces aureofaciens ATCC 10762 was compared with that of free cells. Immobilized cells transferred repeatedly to a new production medium, showed a fourfold increase in the half life time of antibiotic production.In an air bubble column a high chlortetracycline productivity was obtained with a high aeration rate.A semicontinuous production of chlortetracycline by immobilized S. aureofaciens could be improved by varying the fermentation conditions.For continuous chlortetracycline production by immobilized cells, no improvement was detected.     

Enhanced production of bioethanol and ultrastructural characteristics of reused Saccharomyces cerevisiae immobilized calcium alginate beads

Yeast immobilized on alginate beads produced a higher ethanol yield more rapidly than did free yeast cells under the same batch-fermentation conditions. The optimal fermentation conditions were 30 °C, pH 5.0, and 10% initial glucose concentration with 2% sodium alginate beads. The fermentation time using reused alginate beads was 10-14 h, whereas fresh beads took 24 h, and free cells took 36 h. All bead samples resulted in nearly a 100% ethanol yield, whereas the free cells resulted in an 88% yield. Transmission electron microscopy (TEM) showed that the shortened time and higher yield with the reused beads was due to a higher yeast population per bead as well as a higher porosity. The ultrastructure of calcium alginate beads and the alginate matrix structure known as the “egg-box” model were observed using TEM.