微波及其联合杀菌技术在食品中的应用研究进展

微波在食品中的应用已逐渐成为研究热点，但微波作为一种新型食品杀菌技术，特别是和其他杀菌技术联合应用的综述目前还较少。本文通过分析已有的食品微波杀菌技术，包括单微波杀菌技术、微波-巴氏杀菌技术、微波-超声联合杀菌技术、微波-红外杀菌技术、微波-脉冲电场杀菌技术的特点，总结微波及其联合杀菌技术对不同类型食品的杀菌条件和效果，旨在为微波在各类食品杀菌工艺中的应用提供参考。     

Heat transfer analysis of Staphylococcus aureus on stainless steel with microwave radiation

Staphylococcus aureus (NCTC 6571; Oxford strain) on stainless steel discs was exposed to microwave radiation at 2450 MHz and up to 800 W. Cell viability was reduced as the exposure time increased, with complete bacterial inactivation at 110 s, attaining a temperature of 61.4 degrees C. The low rate of temperature rise, RT, of the bacterial suspension as compared with sterile distilled water or nutrient broth suggests a significant influence of the microwave sterilization efficacy on the thermal properties of the micro-organisms. The heat transfer kinetics of thermal microwave irradiation suggest that the micro-organism has a power density at least 51-fold more than its surrounding liquid suspension. When the inoculum on the stainless steel disc was subjected to microwave radiation, heat conduction from the stainless steel to the inoculum was the cause of bacteriostasis with power absorbed at 23.8 W for stainless steel and 0.16 W for the bacteria-liquid medium. This report shows that the microwave killing pattern of Staph. aureus on stainless steel was mainly due to heat transfer from the stainless steel substrate and very little direct energy was absorbed from the microwaves.     

光频微波对黄曲霉的杀灭试验

黄曲霉是污染粮食、食品、中药材和烟丝的常见霉菌。由于黄曲霉的产物黄曲霉毒素具有很强的致癌作用。因此 ,从这些食品或物品中消除黄曲霉可减少甚至消除黄曲霉毒素的危害。报告了微波辐射杀灭烟丝中黄曲霉的效果。光频微波对烟丝上的黄曲霉菌具有良好的杀灭作用 ,微波辐射 30s后菌落数明显减少 ,经 4 5s作用后可完全杀灭黄曲霉的细胞 (包括菌丝和孢子 )。应用光频微波辐射杀灭黄曲霉具有经济、方便和高效的优点 ,既可以用于大规模工业生产 ,亦可在家庭生活中使用。     

Surface Decontamination in an Autoclave Chamber with Formaldehyde Gas

A simple device for the conversion of a standard steam autoclave into a formalde-hyde gas sterilization chamber is described.     

人脑源性神经营养因子cDNA在COS7细胞中的表达及活性研究

本文从质粒Ｍ１３ｍｐ１８－ｈＢＤＮＦ中酶切回收人脑源性神经营养因子（ｈＢＤＮＦ）全长基因,构建真核表达载体ｐＣＭＶ４－ｈＢＤＮＦ。利用脂质体的方法转染ＣＯＳ７细胞,对转染后的ＣＯＳ７细胞提取ＲＮＡ进行狭缝杂交分析和免疫细胞化学反应,分别从转录及翻译水平上检测ＢＤＮＦ基因在ＣＯＳ７细胞中的表达。实验还证实在ＣＯＳ７细胞中表达的ｈＢＤＮＦ蛋白可分泌至胞外并可促进中脑黑质细胞的发育和生长,具有良好的生物学活性。     

Mechanical strength of bone allografts subjected to chemical sterilization and other terminal processing methods

Infectious disease transmission through the use of human donor allografts can be a catastrophic complication in an otherwise straightforward surgical procedure. The use of bone allograft in reconstructive orthopedic surgeries is increasing, yet severe complications, including death, can result if the transplanted tissues transmit a communicable disease to the tissue recipient. The BioCleanse((R)) tissue sterilization process is a fully automated, low-temperature chemical sterilization process that renders allograft tissue sterile. The purpose of this study was to evaluate the effect of a chemical tissue sterilization process on the mechanical strength of cortical bone allografts prior to implantation. Cylindrical cortical bone specimens were harvested from seven human cadaver donors and treated either by: chemical sterilization alone; chemical sterilization and terminal sterilization by gamma irradiation; chemical sterilization, lyophilization, terminal sterilization by STERRAD and rehydration; or untreated. The specimens were tested to failure in axial compression, diametral compression, shear, or bending. There were no significant differences in ultimate stress, strain, or fracture energy between the chemically sterilized and control groups in any of the testing modes.     

How to Ignite an Atmospheric Pressure Microwave Plasma Torch without Any Additional Igniters

This movie shows how an atmospheric pressure plasma torch can be ignited by microwave power with no additional igniters. After ignition of the plasma, a stable and continuous operation of the plasma is possible and the plasma torch can be used for many different applications. On one hand, the hot (3,600 K gas temperature) plasma can be used for chemical processes and on the other hand the cold afterglow (temperatures down to almost RT) can be applied for surface processes. For example chemical syntheses are interesting volume processes. Here the microwave plasma torch can be used for the decomposition of waste gases which are harmful and contribute to the global warming but are needed as etching gases in growing industry sectors like the semiconductor branch. Another application is the dissociation of CO₂. Surplus electrical energy from renewable energy sources can be used to dissociate CO₂ to CO and O₂. The CO can be further processed to gaseous or liquid higher hydrocarbons thereby providing chemical storage of the energy, synthetic fuels or platform chemicals for the chemical industry. Applications of the afterglow of the plasma torch are the treatment of surfaces to increase the adhesion of lacquer, glue or paint, and the sterilization or decontamination of different kind of surfaces. The movie will explain how to ignite the plasma solely by microwave power without any additional igniters, e.g., electric sparks. The microwave plasma torch is based on a combination of two resonators — a coaxial one which provides the ignition of the plasma and a cylindrical one which guarantees a continuous and stable operation of the plasma after ignition. The plasma can be operated in a long microwave transparent tube for volume processes or shaped by orifices for surface treatment purposes.     

Transfer of light-induced electron-spin polarization from the intermediary acceptor to the prereduced primary acceptor in the reaction center of photosynthetic bacteria.

In reaction centers and chromatophores of photosynthetic bacteria strong light-induced emissive ESR signals have been found, not only after a flash but also under continuous illumination. The signal, with g = 2.0048 and delta Hpp = 7.6 G, is only present under reducing conditions in material in which the primary acceptor, ubiquinone, U and its associated high-spin ferrous ion are magnetically uncoupled. its amplitude under continuous illumination is strongly dependent on light intensity and on microwave power. The emissive signal is attributed to the prereduced primary acceptor, U-, which becomes polarized through transfer of spin polarization by a magnetic exchange interaction with the photoreduced, spin polarized intermediary acceptor, I-. A kinetic model is presented which explains the observed dependence of emissivity on light intensity and microwave power. Applying this analysis to the light saturation data, a value of the exchange rate between I- and U- of 4.10(8) s-1 is derived, corresponding to an exchange interaction of 3--5 G.     

Structural organization of the copulation site in the medfly Ceratitis capitata (Diptera: Tephritidae) and observations on sperm transfer and storage

The copulation site of the medfly Ceratitis capitata was investigated at anatomical and ultrastructural levels. It consists of the anterior vagina, with a ventral fertilization chamber and a dorsal insemination pocket into which the two spermathecal ducts open. The fertilization chamber is an organ comprised of a number of alveoli that in virgin females are filled with a filamentous secretion, whereas in mated females contain sperm bundles. Through study of the internal morphology of the aedeagus, its position in the anterior vagina, and the direct observation of sperm transfer and storage, we confirmed that sperm are ejaculated through two gonopores at the top of the distiphallus and another at the base of the genital rod. The sperm flow dorsally into the insemination pocket and ventrally into the fertilization chamber. During copulation, the two spermathecae and the fertilization chamber are progressively filled with spermatozoa.     

Portable Ethylene Oxide Sterilization Chamber

A portable ethylene oxide sterilization chamber was designed, constructed, and tested for use in the sterilization of embolectomy catheters. The unit can accommodate catheters up to 40 inches (101.6 cm) in length and can be operated for less than 4 cents per cycle. A constant concentration of 500 mg of ethylene oxide per liter of space and holding periods of 4 and 6 hr at 43 and 22 C, respectively, were adequate when tested with B. subtilis spores. The estimated cost of construction was $165.00. If temperature control is unnecessary, the cost is approximately $80.00.     

No Major Differences Found between the Effects of Microwave-Based and Conventional Heat Treatment Methods on Two Different Liquid Foods

Extension of shelf life and preservation of products are both very important for the food industry. However, just as with other processes, speed and higher manufacturing performance are also beneficial. Although microwave heating is utilized in a number of industrial processes, there are many unanswered questions about its effects on foods. Here we analyze whether the effects of microwave heating with continuous flow are equivalent to those of traditional heat transfer methods. In our study, the effects of heating of liquid foods by conventional and continuous flow microwave heating were studied. Among other properties, we compared the stability of the liquid foods between the two heat treatments. Our goal was to determine whether the continuous flow microwave heating and the conventional heating methods have the same effects on the liquid foods, and, therefore, whether microwave heat treatment can effectively replace conventional heat treatments. We have compared the colour, separation phenomena of the samples treated by different methods. For milk, we also monitored the total viable cell count, for orange juice, vitamin C contents in addition to the taste of the product by sensory analysis. The majority of the results indicate that the circulating coil microwave method used here is equivalent to the conventional heating method based on thermal conduction and convection. However, some results in the analysis of the milk samples show clear differences between heat transfer methods. According to our results, the colour parameters (lightness, red-green and blue-yellow values) of the microwave treated samples differed not only from the untreated control, but also from the traditional heat treated samples. The differences are visually undetectable, however, they become evident through analytical measurement with spectrophotometer. This finding suggests that besides thermal effects, microwave-based food treatment can alter product properties in other ways as well.     

100～700 mL液体培养基的微波灭菌效果观察

为研究家用微波炉对少量液体培养基的灭菌效果,对100 -700 mL液体培养基采取微波分别进行灭菌,测定其灭菌时间,并对达到灭菌效果的培养基通过接种不同细菌进行质检.结果显示100、200、300、400、500、600、700 mL液体培养基分别在4.5、5.0、7.0、9.0、12.0、19.0、25.0 min达到最有效的灭菌效果.室温保存15 d仍无细菌生长.枯草杆菌黑色变种芽胞菌测试无菌生长.金黄色葡萄球菌、大肠埃希菌及普通变形杆菌在液体培养基里的生长现象、特种后细菌的菌落和形态染色特征及其生化反应均无明显差异.实验表明2 450 MHz,700 W的微波炉对100 - 700 mL的液体培养基不但能快速达到有效的灭菌效果,且营养成分不会被破坏.     

生物辐射场对玉米自交系诱变效应研究

用小麦群体辐射场,经自制生物场辐射仪的收集、放大,会聚于共振控内,对萌发玉米种子进行辐照,研究小麦群体辐射场对玉米的诱变效应。试验结果表明,小麦群体辐射场可诱导玉米植株形态产生变异,获得多茎多穗玉米突变类型,按青贮饲料指标测产,产量比对照组显著提高。     

Factors Influencing the Activity of Sterile Filtered and Heat-Sterilized Trypsin Solutions

The mode of sterilization (filtration or heat) was found to significantly affect the activity of trypsin solutions. Trypsin activity was substantially reduced in the initial fractions of filtrate passed through asbestos filter pads; heat-sterilized trypsin was satisfactory for transfer of cell cultures grown on glass. Heat-sterilized trypsin may be useful when elimination of filterable organisms is required.     

The effects of location and design on the diffusion of respiratory gases in mammal burrows

To investigate the constraints placed on the location and design of mammal burrows by the resident mammal's need for an adequate exchange of respiratory gases with the free atmosphere, we constructed several simple mathematical models for the steady-state diffusion of these gases in sterile burrow-soil systems. In this exchange, diffusion through the soil is of prime importance. Openings of narrow tunnels further than three body lengths from a mammal have a negligible effect on its respiratory microenvironment. Since only a short length of a narrow tunnel around the mammal is of importance in this exchange we may confine attention to design and siting criteria for a discrete chamber containing the mammal.The porosity of the soil in which a burrow chamber is sited and the volume of the burrow chamber have strong and moderate effects respectively on the rate of gas exchange between a resident mammal and the free atmosphere. The depth of the burrow chamber, beyond two chamber diameters, has only a weak effect on this transfer. Soil temperature within the thermoneutral zone of the resident mammal has a weak effect on this transfer, but below the thermoneutral zone, where temperature modifies the rate of consumption (production) of respiratory gas, the effect is strong. Concentrations of respiratory gas in the burrow chamber approach free-atmosphere values when soil porosity, soil temperature, and chamber volume increase and burrow depth decreases.Large mammals are more restricted in the design and siting of burrows than small mammals. Our models indicate that normothermic eutherian mammals with masses much in excess of 0·5 kg are precluded from an indefinite occupation of deep burrows in most field situations. In considering the limitations to our models, several avenues for expanding a mammal's respiratory space are suggested.     

Ein neuer CO2-Inkubator für die biologische Forschung

The engineers of the Centre for Scientific Instrument Manufacture of the Academy of Science of the GDR have engineered a bench incubator for the requirements of tissue culture and other biological research. The chamber made of corrosion resistant metal has a volume of about 100 litres. The cultures standing at three shelves are areated horizontal by two radial ventilators. The incubator equipped with automatic CO₂-, temperature- and humidity measuring- and regulation systems is distinguished by a new method of sterilization.     

Time-of-flight measurements of the plasma density in the T-11M tokamak

The average plasma density in the T-11M tokamak is determined by means of an O-mode time-of-flight refractometer measuring the propagation time τ of microwave pulses through the plasma. Since the front duration τ_fr of these pulses is shorter than 2 ns, filtering the measured signal cannot reduce the signal-to-noise ratio below a certain level. This circumstance impedes the use of this diagnostics in larger devices, where the signals may be substantially attenuated because of the larger chamber size and larger waveguide losses. There are several ways to overcome these difficulties: to raise the microwave power, to increase the sensitivity of the receivers, etc. In this paper, a technique is described that is based on the differential method for determining the propagation time of a microwave signal through the plasma. In this method, the plasma is probed by two continuous microwaves with close frequencies and the phase difference between them Δφ₁₂ is measured. As long as the condition Δφ₁₂ < 2π is satisfied, the measurements are unambiguous, because there are no phase jumps by a value multiple of 2π, as is usually the case in conventional interferometers at an increased level of MHD activity, in regimes with a rapid density growth, etc. This method allows the signal to be filtered, thereby ensuring an appreciable improvement in the signal-to-noise ratio in comparison with the pulsed methods. The first measurements of the average density along the +3-cm chord were performed with the help of this new differential time-of-flight refractometer in the T-11M tokamak. The refractometry data agree well with the interferometric data and are used to recover the plasma-density profile.     

Design,Analysis, and Characterization of Designer Surface Plasmon Polariton-Based Dual-Band Antenna

This paper reports development, design, and analysis of designer (or spoof) surface plasmon polariton-based feeding configuration to excite a dual-band antenna. As an example, a planar transverse electric and magnetic horn antenna is designed and fed by the proposed transition structure. Designer surface plasmon polariton modes are supported by a metal surface at microwave frequency when it is corrugated with periodical grooves. An efficient transition for converting quasi-transverse electric and magnetic waves of microstrip line into spoof surface plasmon polariton (SSPP) waves has been designed in microwave frequency range using periodically corrugated metal strip. SSPP wave is confined at the teeth part of the corrugation. Simulated and measured reflection and transmission characteristics are in good agreement. The spoof SPP-fed dual-band antenna is designed, fabricated, and characterized in microwave anechoic chamber and measured results are coincident with simulated results.     

Differences in the Access to Sterilization between Women Living and Not Living with HIV: Results from the GENIH Study,Brazil

BackgroundIn many countries, young women of reproductive age have been especially affected by the HIV epidemic, which have fostered research to better understand how HIV infection influences and shapes women´s fertility and reproductive and sexual decisions. In Brazil, few studies have focused on the impact of the HIV epidemic on contraceptive choices among women living with HIV (WLHIV).ObjectiveThis study evaluates the impact HIV infection may have in the access to female sterilization in Brazil, using a time-to-event analysis.MethodsA cross-sectional quantitative study (GENIH study) was conducted between February 2013 and April 2014 in the city of São Paulo, comparing two probabilistic samples of 975 WLHIV and 1,003 women not living with HIV (WNLHIV) aged 18 to 49. Sexual and reproductive data was collected retrospectively in order to reconstruct women''s reproductive trajectories. Given the objectives of this study, the analysis was restricted to women with parity one or more and, in case of WLHIV, to those sterilized after HIV diagnosis and not infected through vertical transmission. The final sample analysis included 683 WNLHIV and 690 WLHIV. A series of multivariable-adjusted Cox models estimated the probability of being sterilized after HIV diagnosis, compared with WNLHIV. Models were adjusted for schooling, race/color, and stratified by parity at last delivery (1–2, 3+). Hazard ratios were calculated for female sterilization, and separately for interval and postpartum procedures (performed in conjunction with caesarean section or immediately after vaginal delivery). Additionally, information regarding unmet demand for female sterilization was also explored.FindingsNo statistical difference in the overall risk of sterilization between WLHIV and WNLHIV in the two parity-related groups is observed: HR = 0.88 (0.54–1.43) and 0.94 (0.69–1.29), respectively, among women with 1–2 children and those with three and more. However, significant differences regarding the impact of HIV infection at sterilization are observed depending on the timing and the type of sterilization procedure. The probability of obtaining an interval sterilization is significantly lower for WLHIV compared to those not living with HIV. The reverse occurs regarding postpartum sterilization. Although sterilization is mainly performed in conjunction with caesarean section in Brazil, it is evident that caesarean sections are not the sole factor increasing the risk of sterilization among WLHIV.ConclusionThe results indicate barriers in the access to services offering interval sterilization for WLHIV and certain facilitation in obtaining the procedure in conjunction with caesarean section. Health policy makers at local and national levels should promote institutional changes in order to facilitate access to interval sterilization and to confront the sensitive discussion of WLHIV’s eligibility for postpartum sterilization. It is also urgent to increase access to a wider range of contraceptive methods for WLHIV and promote dual method protection strategies. Moreover, since condom use may decrease in the future in the context of the preventive effect of antiretroviral therapy, promoting dual methods will expand the choices regarding the reproductive rights of women living with HIV.     

The blue light-specific response of Vicia faba stomata acclimates to growth environment

Stomata in epidermal strips from growth chamber-grown Vicia faba leaves opened less in response to white light than did stomata from greenhouse-grown leaves. Chlorophyll-mediated, red light-stimulated opening was similar in stomata from the two growth conditions, but stomata from the growth chamber environment had a severely reduced response to blue light. Transfer of plants between the two growth conditions resulted in an acclimation of the stomatal blue light response. Stomata lost blue light sensitivity within 1 d of transfer to growth chamber conditions and gained sensitivity to blue light over an 8 d period after transfer to a greenhouse. Short-term transfer experiments confirmed that the rapid loss of blue light sensitivity was an acclimation response, requiring between 12 and 20 h exposure to growth chamber conditions. The acclimation of the stomatal response to blue light was inversely related to a previously reported acclimation response in which stomata change between high CO2 sensitivity under growth chamber conditions and low CO2 sensitivity under greenhouse conditions. The time courses of the blue light and CO2 acclimation responses were virtually identical, suggesting the possibility of a common acclimation mechanism.