Conversion of cereal residues into biogas in a rumen-derived process

A recently developed high-rate, two-phase process, which employs rumen microorganisms for efficient acidogenesis, was tested for anaerobic degradation of barley straw, rye straw, and maize stover. Under conditions similar to those of the rumen and loading rates varying between 9.8 and 26.0 g of organic matter/I/day in the first phase (acidogenic reactor), total fibre degradation efficiencies ranged between 42% and 57%, irrespective of the loading rate applied. Average specific production of volatile fatty acids and biogas/g volatile solid digested in the acidogenic reactor varied between 6.9 and 11.2 mmol and 0.10 and 0.25 l, respectively.The effect of varying solid retention times on the extent of degradation of barley straw was examined. Changing of retention times in the range of 60 to 156 h had no effect on degradation efficiency, but a decrease in efficiency was observed at retention times below 60 h.By connecting the acidogenic reactor in series to an Upflow Anaerobic Sludge Blanket (UASB) methanogenic reactor the volatile fatty acids were converted into biogas. Average methane contents of the gases produced in the acidogenic reactor and in the UASB reactor were 30±3% and 78±3%, respectively.     

Granule development and performance in sucrose fed anaerobic baffled reactors

Two 90 L anaerobic baffled reactors were used to study the granulation of sludge and the effect of the organic loading rate and NaHCO3/COD ratios on reactor performance. Furthermore, it was determined whether an anaerobic baffled reactor would promote phase separation and if additive of bentonite or granular active carbon was capable of enhancing granule formation. In order to minimize feed variations, and have a totally biodegradable substrate, a synthetic sucrose substrate was used. Granulation was achieved in both reactors within 75 days. However, the granules from the granular active carbon amended reactor appeared earlier and were larger and more compact. The reactors were maintained at a hydraulic retention time of 20 h during performance study stage. The results showed that when organic loading rate were changed from 2.15 to 6.29 kg COD m(-3)day(-1), chemical oxygen demand (COD) removal was not decreased (91-93%), but a slight increase in effluent COD was observed. It was found that the COD removals were generally good (87-92%) and had not obviously change with the decreasing NaHCO3/COD ratios. From the bacterial distribution and the concentration of volatile fatty acids in four compartments, it was concluded that a separation of phases occurred within the anaerobic baffled reactors.     

Two-stage UASB design enables activated-sludge free treatment of easily biodegradable wastewater

A two-stage lab-scale UASB reactor, incorporating a selector-type UASB prior to the main reactor was operated at 37 °C with an easily biodegradable food wastewater having a COD of 3,000 mg/L. Varying the hydraulic retention time from 25 to 5 h, the removal of COD by the two-stage process was higher than 95%. Effluent soluble COD was consistently below 75 mg/L and the methane production rate close to theoretical values. The selector UASB removed the majority of the organic load (70–90%) at high organic loading rate, i.e. between 6 and 30 g/(Ld) and the granular sludge developed was characterized by dense microbial colonies, high volatile suspended solids’ content and high substrate degradation efficiency. Design of a two-stage process, incorporating a selector and a second UASB reactor, was able to achieve stable and complete substrate degradation at overall loading rates of the order of ~10–15 g/(Ld).     

Continuous anaerobic treatment of wastewaters containing formaldehyde and urea

The toxicity of formaldehyde (FA) in batch assays, using volatile fatty acids (VFA) as co-substrate, and the continuous anaerobic treatment of wastewaters containing FA in upflow anaerobic sludge blanket (UASB) reactors was investigated. In batch studies, FA exerted a 50% methanogenic toxicity on VFA at concentrations of around 100 mg/l, 2.5 times lower than values reported with sucrose. Although at FA concentrations higher than 200 mg/l methanogenesis was completely inhibited, a partial recovery of the bacterial activity was observed after 250 h when the FA had been removed from the medium. The continuous anaerobic degradation of FA at concentrations up to 2 g/l, using 1.6 g/l of glucose as co-substrate, was studied in a UASB reactor. A stable and efficient operation was observed at organic loading rates (OLR) of 6.0 g COD/l·d and with a COD/FA ratio as low as 1.4. A synthetic substrate with the same characteristics as the effluents produced during fibreboard adhesives manufacturing (based on urea-FA), i.e. 0.95 g FA/l and 0.35 g urea/l, was treated in a UASB reactor. The applied OLR and nitrogen loading rate (NLR) were 3.45 g COD/l·d and 0.58 g N/l·d, respectively. COD removal efficiencies were maintained at 90–95%, FA and urea being completely degraded.     

Effect of feeding strategy on the stability of anaerobic sequencing batch reactor responses to organic loading conditions

The goal of this study was to examine the effect of feeding strategy on the capability for treatment and the stability of an anaerobic sequencing batch reactor (ASBR) under increasing organic loading. The lab-scale ASBR systems were operated at 35 degrees C using synthetic organic wastewater under both batch and fed-batch operational modes with different feed to cycle time (F:C) ratios. Experimental studies were conducted over a wide range of volumetric organic loading rates (VOLRs) (1.524 g COD/l/d) by varying the hydraulic retention time (HRT) (1.25, 2.5, and 5d) and the feed wastewater's COD (3750-30,000 mg/l). With an F:C ratio greater than or equal to 0.42, the fed-batch mode operation showed higher system efficiency in COD removal, volumetric methane production rate (VMPR), and specific methane production rate (SMPR) as compared to those in the batch mode with identical VOLR and HRT. In the fed-batch mode, the COD removals reached 86-95% with VOLR up to 12 g COD/l/d. The maximums for VMPR of 3.17 l CH4/l/d and for SMPR of 1.63 g CH4-COD/g VSS/d were achieved with a VOLR of 12 g COD/l/d at HRTs of 2.5 and 1.25 d, respectively. The fed-batch operation presented a lower concentration of volatile fatty acids (VFAs) than those in the batch operation. A lower concentration of VFAs confirmed the stability and efficiency of the fed-batch mode operation. The specific methanogenic activity (SMA) analysis showed that the VFA-degrading activity of the biomass in the fed-batch mode was higher for acetate and butyrate, and lower for propionate. Determined biomass yield and bacterial decay coefficients in the fed-batch operational mode were 0.05 g VSS/g COD rem and 0.001 d(-1), respectively.     

Production of PHA from starchy wastewater via organic acids

Polyhydroxyalkanoate (PHA) was produced from a starchy wastewater in a two-step process of microbial acidogenesis and acid polymerization. The starchy organic waste was first digested in a thermophilic upflow anaerobic sludge blanket (UASB) reactor to form acetic (60-80%), propionic (10-30%) and butyric (5-40%) acids. The total volatile fatty acids reached 4000 mg l(-1) at a chemical oxygen demand (COD) loading rate of 25-35 g l(-1) day(-1). A carbon balance indicates that up to 43% of the organic carbon in the starchy waste went to the organic acids and the rest to biogas, volatile suspended solids and residual sludge accumulated in the reactor. The acid composition profile was affected by COD loading rate: a medium rate around 9 g l(-1) day(-1) gave a high propionic acid content (29% wt) and a high rate around 26 g l(-1) day(-1) led to a high butyric acid content (34% wt). The acids in the effluent solution after microfiltration were utilized and polymerized into PHA by bacterium Alcaligenes eutrophus in a second reactor. Fifty grams of PHA was produced from 100 g total organic carbon (TOC) utilized, a yield of 28% based on TOC, which is comparable with 55 g PHA per 100 g TOC of pure butyric and propionic acids used. PHA formation from individual acids was further investigated in a semi-batch reactor with three acid feeding rates. With a limited nitrogen source (80-100 mg NH(3) per liter), the active biomass of A. eutrophus, not including the accumulated PHA in cells, was maintained at a constant level (8-9 g l(-1)) while PHA content in the cell mass increased continuously in 45 h; 48% PHA with butyric acid and 53% PHA with propionic acid, respectively. Polyhydroxybutyrate was formed from butyric acid and poly(hydroxybutyrate-hydroxyvalerate) formed from propionic acid with 38% hydroxyvalerate.     

Evaluation of UASB reactor performance during start-up operation using synthetic mixed-acid waste

A start-up experiment was performed in a laboratory-scale, upflow anaerobic sludge blanket (UASB) reactor using seed sludge from a domestic waste treatment plant at 3.8-33.3gCODl(-1)day(-1) loading rates. Analysis over the height of the reactor with time showed that the VSS in the reactor was initially differentiated into active and non-active biomass at increasing gas production and upflow velocities, and specific update rates of the volatile fatty acids (VFA) components were pronounced at the bottom 10% of the reactor. During start-up, specific methanogenic activity and chemical oxygen demand (COD) uptake rate increased from 0.075 to 0.75gCOD-CH(4)(gVSS)(-1)day(-1) and from 0.08 to 0.875gCOD removed (gVSS)(-1)day(-1), respectively. When seed sludge from a distillery waste treatment plant was used, improved performance due to a predominance of active biomass was evident when the loading rate was increased from 9.4 to 28.7gCODl(-1)day(-1). The proposed start-up evaluation is an effective tool to successfully monitor performance of UASB reactors.     

Performance evaluation of a mesophilic anaerobic fluidized-bed reactor treating wastewater derived from the production of proteins from extracted sunflower flour

A study of the anaerobic digestion of wastewater derived from the production of protein isolates from extracted sunflower flour was carried out in a laboratory-scale, mesophilic (35 degrees C) fluidized-bed reactor with saponite as bacterial support. Chemical oxygen demand (COD) removal efficiencies in the range of 98.3-80.0% were achieved in the reactor at organic loading rates (OLR) of between 0.6 and 9.3 g COD/I d, hydraulic retention times (HRT) of between 20.0 and 1.1 d and average feed COD concentration of 10.6 g/l. Eighty percent of feed COD could be removed up to OLR of 9.3 g COD/l d. The yield coefficient of methane production was 0.33 l of methane (at STP) per gram of COD removed and was virtually independent of the OLR applied. Because the buffering capacity of the experimental system was maintained at favorable levels with excess total alkalinity present at all loadings, the rate of methanogenesis was not affected by loading. The experimental data indicated that a total alkalinity in the range of 2,000-2,460 mg/l as CaCO3 was sufficient to prevent the pH from dropping to below 7.0 for OLR of up to 9.3 g COD/l d. The volatile fatty acid (VFA) levels and the VFA/alkalinity ratio were lower than the suggested limits for digester failure (0.3-0.4) for OLR and HRT up to 9.3 g COD/l d and 1.1 d, respectively. For a HRT of 0.87 d (OLR of 12.1 g COD/l d) the start of acidification was observed in the reactor.     

上流式厌氧滤器微生物学特性的研究

采用改良的Hungate厌氧技术研究了上流式厌氧滤器微生物学特性与反应器运行性能之间的关系。结果表明,COD和挥发性脂肪酸去除率与各类菌数密切相关;短时间有机负荷改变和反应器停止运行对各类菌数略有影响;反应器运行稳定性取决于各类细菌的合适数量比例以及协同作用。     

High-Rate two-phase process for the anaerobic degradation of cellulose, employing rumen microorganisms for an efficient acidogenesis

A novel two-stage anaerobic process for the microbial conversion of cellulose into biogas has been developed. In the first phase, a mixed population of rumen bacteria and ciliates was used in the hydrolysis and fermentation of cellulose. The volatile fatty acids (VFA) produced in this acidogenic reactor were subsequently converted into biogas in a UASB-type methanogenic reactor.A stepwise increase of the loading rate from 11.9 to 25.8 g volatile solids/L reactor volume/day (g VS/L/day) did not affect the degradation efficiency in the acidogenic reactor, whereas the methanogenic reactor appeared to be overloaded at the highest loading rate. Cellulose digestion was almost complete at all loading rates applied. The two-stage anaerobic process was also tested with a closed fluid circuit. In this instance total methane production was 0.438 L CH(4)g VS added, which is equivalent to 98% of the theoretical value. The application of rumen microorganisms in combination with a high-rate methane reactor is proposed as a means of efficient anaerobic degradation of cellulosic residues to methane. Because this newly developed two-phase system is based on processes and microorganisms from the ruminant, it will be referred to as "Rumen Derived Anaerobic Digestion" (RUDAD-) process.     

A further study of the anaerobic biotreatment of malt whisky distillery pot ale using an UASB system

Pot ale from a pilot-scale malt whisky distillery was treated using a mesophilic upflow anaerobic sludge blanket (UASB) digester. Stable operation was observed at organic loading rates (OLRs) of 5.46 kg COD/m3 day or less when the pot ale was diluted with tap water. Digester failure occurred when undiluted pot ale was used, even though OLR was less than 5 kg COD/m3 day. Overall performance was worse than that observed previously when UASB digesters were used to treat pot ale from a different source supplemented with trace elements. A substantial proportion of effluent chemical oxygen demand (COD) was present as volatile fatty acids (VFA), particularly during periods of reactor stress, indicating that overall performance was limited by the rate of VFA conversion. Wastewater alkalinity rose during digestion. The sludge which developed in the reactor was flocculent but did not form compact granules.     

Effect of non-feeding period length on the intermittent operation of UASB reactors treating dairy effluents

Recent environmental concerns have prompted a re-evaluation of conventional management strategies and refueled the search of innovative waste management practices. In this sense, the anaerobic digestion of both fat and the remaining complex organic matter present in dairy wastewaters is attractive, although the continuous operation of high rate anaerobic processes treating this type of wastewaters causes the failure of the process. This work accesses the influence of non-feeding period length on the intermittent operation of mesophilic UASB reactors treating dairy wastewater, in order to allow the biological degradation to catch up with adsorption phenomenon. During the experiments, two UASB reactors were subject to three organic loading rates, ranging from 6 to 12 g(COD) x L(-1) x d(-1), with the same daily load applied to both reactors, each one with a different non-feeding period. Both reactors showed good COD removal efficiencies (87-92%). A material balance for COD in the reactors during the feeding and non-feeding periods showed the importance of the feedless period, which allowed the biomass to degrade substrate that was accumulated during the feeding period. The reactor with the longest non-feeding period had a better performance, which resulted in a higher methane production and adsorption capacity for the same organic load applied with a consequent less accumulation of substrate into the biomass. In addition, both reactors had a stable operation for the organic load of 12 g(COD) x L(-1) x d(-1), which is higher than the maximum applicable load reported in literature for continuous systems (3-6 g(COD) x L(-1) x d(-1)).     

Packed- and fluidized-bed biofilm reactor performance for anaerobic wastewater treatment

Anaerobic degradation performance of a laboratory-scale packed-bed reactor (PBR) was compared with two fluidized-bed biofilm reactors (FBRs) on molasses and whey feeds. The reactors were operated under constant pH (7) and temperature (35 degrees C) conditions and were well mixed with high recirculation rates. The measured variables were chemical oxygen demand (COD), individual organic acids, gas composition, and gas rates. As carrier, sand of 0.3-0.5 mm diameter was used in the FBR, and porous clay spheres of 6 mm diameter were used in the PBR. Startup of the PBR was achieved with 1-5 day residence times. Start-up of the FBR was only successful if liquid residence times were held low at 2-3 h. COD degradations of 86% with molasses (90% was biodegradable) were reached in both the FBR and PBR at 6 h residence time and loadings of 10 g COD/L day. At higher loadings the FBR gave the best performance; even at 40-45 g COD/L day, with 6 h residence times, 70% COD was degraded. The PBR could not be operated above 20 g COD/L day without clogging. A comparison of the reaction rates show that the PBR and FBR per formed similarly at low concentrations in the reactors up to 1 g COD/L, while above 3 g COD/L the rates were 17.4 g COD/L day for the PBR and 38.4 g COD/L day for the FBR. This difference is probably due to diffusion limitations and a less active biomass content of the PBR compared with the fluidized bed.The results of dynamic step change experiments, in which residence times and feed concentrations were changed hanged at constant loading, demonstrated the rapid response of the reactors. Thus, the response times for an increase in gas rate or an increase in organic acids due to an increase in feed concentration were less than 1 day and could be explained by substrate limitation. Other slower responses were observed in which the reactor culture adapted over periods of 5-10 days; these were apparently growth related. An increase in loading of over 100% always resulted in large increases inorganic acids, especially acetic and propionic, as well as large increases in the CO(2) gas content. In general, the CO(2) content of the gas was very low, due to the large amount of dissolved CO(2) that exited with the liquid phase at low residence times. The performance of the FBR with whey was comparable to its performance with molasses, and switching of molasses to whey feed resulted in immediate good performance without adaptation.     

Integration of ozonation and an anaerobic sequencing batch reactor (AnSBR) for the treatment of cherry stillage

Cherry stillage is a high strength organic wastewater arising from the manufacture of alcoholic products by distillation of fermented cherries. It is made up of biorefractory polyphenols in addition to readily biodegradable organic matter. An anaerobic sequencing batch reactor (AnSBR) was used to treat cherry stillage at influent COD ranging from 5 to 50 g/L. Different cycle times were selected to test biomass organic loading rates (OLR(B)), from 0.3 to 1.2 g COD/g VSS.d. COD and TOC efficiency removals higher than 80% were achieved at influent COD up to 28.5 g/L but minimum OLR(B) tested. However, as a result of the temporary inhibition of acetogens and methanogens, volatile fatty acids (VFA) noticeably accumulated and methane production came to a transient standstill when operating at influent COD higher than 10 g/L. At these conditions, the AnSBR showed signs of instability and could not operate efficiently at OLR(B) higher than 0.3 g COD/g VSS.d. A feasible explanation for this inhibition is the presence of toxic polyphenols in cherry stillage. Thus, an ozonation step prior to the AnSBR was observed to be useful, since more than 75% of polyphenols could be removed by ozone. The integrated process was shown to be a suitable treatment technology as the following advantages compared to the single AnSBR treatment were observed: greater polyphenols and color removals, higher COD and TOC removal rates thus enabling the process to effectively operate at higher OLR, higher degree of biomethanation, and good stability with less risk of acidification.     

A physicochemical-biotechnological approach for an integrated valorization of olive mill wastewater

An integrated physicochemical-biotechnological approach for a multipurpose valorization of olive mill wastewaters was studied. More than 60% of the wastewater natural polyphenols were recovered through a solid phase extraction procedure, by employing Amberlite XAD16 resin as the adsorbent and ethanol as the biocompatible desorbing phase. Thereafter, the dephenolized effluent was fed to a mesophilic anaerobic acidogenic packed-bed biofilm reactor for the bioconversion of the organic leftover into volatile fatty acids (VFAs). A VFAs concentration of 19 gCODL(-1) was obtained, representing more than 70% of the COD occurring in the anaerobic effluent. The biotechnological process was assessed by means of bio-molecular analyses, which showed that the reactor packed bed was mostly colonized by bacteria of the Firmicutes phylogenetic group. The biorefinery scheme developed in this study allowed the obtainment of 1.59 g of polyphenols per liter of wastewater treated and 2.72 gCODL(-1) day(-1) of VFAs.     

Treatment of leachate from a solid waste landfill site using a two-stage anaerobic filter

Raw leachate was treated using a two-stage upflow anaerobic filter process. Leachate from a solid waste landfill site, which received both municipal and industrial wastes, contained high organic matter (17-21 g/L COD, 13-14 g/L BOD, and 3.5-4.6 g/L volatile acids), and low metal (Zn and Fe) concentrations. Depending on sampling time, leachate composition and characteristics varied considerably. At an organic loading up to 4 g COD/day(2) media area, the BOD and COD removal percentages were 98 and 91%, respectively. The biofilters were also effective for metal removal. However, the filter effluent contained a high concentration of ammonia. System overloading was characterized by the accumulation of large quantities of volatile acids and by a now ratio of alkalinity/volatile acids, resulting in low COD removal and reduced gas production. Once the first filter was upset, the second stage could only partially respond to the volatile acids accumulated in the effluent of first filter.     

Studies on SAGO wastewater treatment using anaerobic rotating biological contactor

Experimental studies were done in a laboratory scale Anaerobic Rotating Biological Contactor (RBC), for treatment of Synthetic sago wastewater. This paper describes the development and laboratory testing of an Anaerobic RBC process that couples the advantages of the fixed film horizontal flow RBC process with the high strength, starch degradation capabilities of anaerobic systems. The reactor was operated at ambient temperature and was subjected to organic and hydraulic loading rates. The reactor performance with respect to Chemical Oxygen Demand (COD) removal, alkalinity, volatile acids at each stage and biogas production were evaluated. The Anaerobic RBC reactor liquid volume is 70 litres and total disc surface area is 4.45 m². The reactor was operated with about 100% of the disc area submerged and with a rotational speed held constant at 9?rev/min. The synthetic sago wastewater was started with a COD value of 1087?mg/l at a hydraulic retention time(HRT) of 42?h and it was varied till maximum COD of 9522?mg/l. From the present study, the optimum COD load was found to be 6860?mg/l with a COD removal efficiency of 97.2%.With this optimum COD load, hydraulic loading rate(HLR) study was done at 24?h to 48?h HRT. COD removal efficiencies at hydraulic loading rates were compared with the work of Subrahmanyam &; Sastry (1988). From the present study, the proportionality coefficient was found to be 1.18 with process efficiencies at different hydraulic loading rates.     

Comparison of two-stage thermophilic (68 degrees C/55 degrees C) anaerobic digestion with one-stage thermophilic (55 degrees C) digestion of cattle manure

A two-stage 68 degrees C/55 degrees C anaerobic degradation process for treatment of cattle manure was studied. In batch experiments, an increase of the specific methane yield, ranging from 24% to 56%, was obtained when cattle manure and its fractions (fibers and liquid) were pretreated at 68 degrees C for periods of 36, 108, and 168 h, and subsequently digested at 55 degrees C. In a lab-scale experiment, the performance of a two-stage reactor system, consisting of a digester operating at 68 degrees C with a hydraulic retention time (HRT) of 3 days, connected to a 55 degrees C reactor with 12-day HRT, was compared with a conventional single-stage reactor running at 55 degrees C with 15-days HRT. When an organic loading of 3 g volatile solids (VS) per liter per day was applied, the two-stage setup had a 6% to 8% higher specific methane yield and a 9% more effective VS-removal than the conventional single-stage reactor. The 68 degrees C reactor generated 7% to 9% of the total amount of methane of the two-stage system and maintained a volatile fatty acids (VFA) concentration of 4.0 to 4.4 g acetate per liter. Population size and activity of aceticlastic methanogens, syntrophic bacteria, and hydrolytic/fermentative bacteria were significantly lower in the 68 degrees C reactor than in the 55 degrees C reactors. The density levels of methanogens utilizing H2/CO2 or formate were, however, in the same range for all reactors, although the degradation of these substrates was significantly lower in the 68 degrees C reactor than in the 55 degrees C reactors. Temporal temperature gradient electrophoresis profiles (TTGE) of the 68 degrees C reactor demonstrated a stable bacterial community along with a less divergent community of archaeal species.     

Anaerobic treatment of highly concentrated aniline wastewater using packed-bed biofilm reactor

The performance of packed-bed biofilm reactor (PBBR) with self-floating bio-carriers was investigated to treat highly concentrated organic nitrogenous aniline wastewater with a COD value as high as 24,000 mg/L. With 45 vol% of carrier charge inside the reactor, the aniline wastewater can be effectively treated with 94% of COD removal efficiency at a low organic loading rate (OLR) of 0.9 kg COD/(m³ d). The removal efficiency decreased gradually down to 75% when OLR increased to 12.27 kg COD/(m³ d) that corresponded to 1 day of HRT. Separate tests with biofilm alone showed that the conversion contribution of the biofilm was about half of the overall COD conversion by the biofilm plus sludge system at the same OLRs of 3–4 kg COD/(m³ d), and that the biofilm had higher activity than suspended sludge. Ammonium released from decomposed aniline was increased gradually from 500 to 1700 mg/L with the OLR increase from 0.9 to 12.27 kg COD/(m³ d), which resulted in inhibitory effect to the microorganism due to the toxicity of free ammonia. Batch anaerobic toxicity tests showed that the biofilm was less sensitive to toxic compounds than suspended sludge and could tolerate higher concentration of free ammonia.     

Two-stage anaerobic treatment of dairy wastewater using HUASB with PUF and PVC carrier

In the present study, an attempt has been made to treat dairy wastewater entirely via anaerobic treatment over a period of 215 days, using two-stage Hybrid Upflow Anaerobic Sludge Blanket (HUASB) reactors, which offer the advantages associated both with fixed film and upflow sludge blanket treatments. A HUASB with polyurethane foam cubes was used for stage I, and a HUASB utilizing PVC-cut rings was used for stage II. The output from stage I was used as the input for stage II. The two-stage reactor was operated at an organic loading rate that varied from 10.7 to 21.4 kg COD m³/d for a period of 215 days, including the start-up period. The ideal organic loading rate for the two-stage reactor was 19.2 kg COD/m³/d. A further 21.4 kg COD m³/d increase in the organic loading rate resulted in the souring of the reactor function in stage I, which consequently reduced the overall reactor performance. Combined COD removal during the stable operation period (10.7 to 19.2 kg COD m³/d) occurred in a range between 97 and 99%. The methane content in the biogas varied from 65 to 70% in stage I, and from 63 to 66% in stage II. The two-stage anaerobic treatment using HUASB with PUF and PVC described in this work is expected to constitute a better alternative for the complete treatment of dairy wastewater than high-rate anaerobic, anaerobic/aerobic, and two-phase anaerobic treatment methods.