Characterisation of a thermophilic L-glutamate dehydrogenase biosensor for amperometric determination of L-glutamate by flow injection analysis

Carbon paste wax electrodes incorporating thermophilic L-glutamate dehydrogenase, NADP and a polymeric toluidine blue O (poly-TBO) mediator have been characterised for the amperometric determination of L-glutamate at 313-318 K in a flow injection analysis (FIA) system. The biosensors exhibit good sensitivity, mechanical stability and reproducibilty, unlike carbon paste- or carbon wax-based electrodes under the same conditions. The carbon paste wax electrode responds linearly to L-glutamate up to 40 mM, the detection limit is 0.3 mM and the RSD (n = 10) for 5 mM L-glutamate was 7.6%. The response to some potential interferents has been quantified. Addition of finely ground hexaammineruthenium (III) trichloride ([Ru(NH3)6]Cl3) to the carbon paste wax electrodes decreases the FIA peak width and increases the peak current. The metal complex appears to accelerate the rate of oxidation of NAD(P)H by poly-TBO.     

The carbon paste electrode encrusted with a microreactor as glucose biosensor.

The amperometric biosensors based on carbon paste electrodes (CPEs) encrusted with single microreactor (MR) have been constructed for the determination of glucose. The MRs were prepared from CPC-silica carrier (CPC) and were loaded with glucose oxidase (GO), mediator (M) and acceptor (A). As the mediator cation radical of 5,10-dimethyl-5, 10-dihydrophenazine (DMDHP), N-methylphenazonium methyl sulfate (PMS) and o-benzoquinone (BQ) and as the acceptor Fe[EDTA]- or Fe(CN)6(3-) was used. The biosensors acted at electrode potential 0.15-0.27 V versus Ag-AgCl electrode. The calibration graphs of the biosensors were linear in the range from 1.5 to 50 mM of glucose. The sensitivity of the biosensors did not change at pH 6-8. The dissolved oxygen little (7%) influenced the biosensors response and 1 mM of ascorbic acid produced the response that was of equal value to 0.5 mM of glucose. The biosensors showed high stability; no change of the response of the biosensors prepared by using the novel microreactor was observed at least for 6 months by keeping the loaded CPC at room temperature in silica container. An optimization of the biosensors response against the GO, the mediator and the polymer amount was performed. The digital modeling of the biosensors action is following.     

Development of highly selective and stable potentiometric sensors for formaldehyde determination

Two types of biosensors selective to formaldehyde have been developed on the basis of pH-sensitive field effect transistor as a transducer. Highly or partially purified alcohol oxidase (AOX) and the permeabilised cells of methylotrophic yeast Hansenula polymorpha (as a source of AOX) have been used as sensitive elements. The response time in steady-state measurement mode is in the range of 10-60 s for the enzyme-based sensors and 60-120 s for the cell-based sensor. When measured in kinetic mode the response time of all biosensors developed was less than 5 s. The linear dynamic range of the sensor output signals corresponds to 5-200 mM formaldehyde for highly and partially purified alcohol oxidase, and 5-50 mM formaldehyde for the cells. The operational stability of the biosensors is not less than 7 h, and the relative standard deviation of intra-sensor response is approximately 2 and 5% for the enzyme- and cell-based sensors, respectively. When stored at 4 degrees C, the enzyme and cell sensor responses have been found stable for more than 60 and 30 days, respectively. Both types of biosensors demonstrate a high selectivity to formaldehyde with no potentiometric response to primary alcohols, including methanol, or glycerol and glucose. The possible reasons of such unexpected high selectivity of AOX-based FET-sensors to formaldehyde are discussed. The influence of the biomembrane composition and the effect of different buffers on the sensor response to formaldehyde are also discussed.     

Recombinant Microdochium nivale carbohydrate oxidase and its application in an amperometric glucose sensor

Biosensors containing recombinant carbohydrate oxidase from Microdochium nivale (rMnO) were developed by means of either chemically modified carbon paste or graphite electrode. 1-(N,N-dimethylamine)-4-(4-morpholine)benzene (AMB) and 1,1'-dimethylferrocene (DMFc) have been used as mediators. The biosensors showed a linear calibration graph up to 18 mM of glucose when operated at 0.04-0.36 V versus a saturated calomel electrode. Almost no change was detected in the sensitivity of the biosensors at pH 7.2-8.1. The biosensors responded to other aldoses in the D-configuration, however, maximal sensitivity of the biosensor was towards D-glucose. The biosensor did not response to polyhydroxylic compounds such as D-mannitol, D-sorbitol and inositol. The advantages of the biosensors based on rMnO in comparison to Aspergillus niger glucose oxidase is a wider linear range, low sensitivity to oxygen and (in some cases) broad specificity.     

Formaldehyde production with heat-treated cells of methanol yeast

Chemostat-grown cells of a methanol yeast, Candida boidini S2 AOU-1, were investigated for formaldehyde production. The productivity and catalytic stability were improved by preincubation of the cells at 37°C for 24 h in 0.1 M potassium phosphate buffer (pH 7.5) containing 50 mM NaN₃. These cells produced 1150 mM formaldehyde after a 10-h reaction.     

Electrogenerated chemiluminescence of ruthenium complex immobilized in a highly cross‐linked polymer and its analytical applications

Electrogenerated chemiluminescence (ECL) of a ruthenium complex polymer modified carbon paste electrode and its analytical applications were investigated. The ruthenium complex polymer was prepared using bis(2,2‐bipyridine) (4,4‐dicarboxy‐2,2‐bipyridine) ruthenium(II). The ECL behaviours of ruthenium complex polymer modified carbon paste electrode were investigated in the absence and presence of tripropylamine (TPA). The modified carbon paste electrode exhibited long‐term stability and fine reproducibility. The ECL intensity of the modified carbon paste electrode was linear with the concentration of TPA in the range 2.0 × 10^–6–3.8 × 10^–3 mol/L, with a detection limit (S:N = 3) of 6 × 10^–7 mol/L. It was also found that raceanisodamine could enhance the ECL intensity of the modified electrode. The ECL intensity of the modified carbon paste electrode was linear with the concentration of raceanisodamine in the range 1.1 × 10^–5–6.0 × 10^–4 mol/L, with a detection limit (S:N = 3) of 6 × 10^–6 mol/L. This work demonstrates that the entrapment of ruthenium complex in a highly cross‐linked polymer is a promising approach to construct an ECL modified electrode with long‐term stability and fine reproducibility. The modified electrode designed has a potential application in the ECL detector. Copyright © 2008 John Wiley & Sons, Ltd.     

Environmental regulation of alcohol metabolism in thermotolerant methylotrophic Bacillus strains

The thermotolerant methylotroph Bacillus sp. C1 possesses a novel NAD-dependent methanol dehydrogenase (MDH), with distinct structural and mechanistic properties. During growth on methanol and ethanol, MDH was responsible for the oxidation of both these substrates. MDH activity in cells grown on methanol or glucose was inversely related to the growth rate. Highest activity levels were observed in cells grown on the C₁-substrates methanol and formaldehyde. The affinity of MDH for alcohol substrates and NAD, as well as V _max, are strongly increased in the presence of a M _r 50,000 activator protein plus Mg²⁺-ions [Arfman et al. (1991) J Biol Chem 266: 3955–3960]. Under all growth conditions tested the cells contained an approximately 18-fold molar excess of (decameric) MDH over (dimeric) activator protein. Expression of hexulose-6-phosphate synthase (HPS), the key enzyme of the RuMP cycle, was probably induced by the substrate formaldehyde. Cells with high MDH and low HPS activity levels immediately accumulated (toxic) formaldehyde when exposed to a transient increase in methanol concentration. Similarly, cells with high MDH and low CoA-linked NAD-dependent acetaldehyde dehydrogenase activity levels produced acetaldehyde when subjected to a rise in ethanol concentration. Problems frequently observed in establishing cultures of methylotrophic bacilli on methanol- or ethanol-containing media are (in part) assigned to these phenomena.Abbreviations MDH NAD-dependent methanol dehydrogenase - ADH NAD-dependent alcohol dehydrogenase - A1DH CoA-linked NAD-dependent aldehyde dehydrogenase - HPS hexulose-6-phosphate synthase - G6Pdh glucose-6-phosphate dehydrogenase     

Application of screen-printed microband biosensors to end-point measurements of glucose and cell numbers in HepG2 cell culture

Microband glucose biosensors were produced by insulating and sectioning through a screen-printed, water-based carbon electrode containing cobalt phthalocyanine redox mediator and glucose oxidase enzyme. Under quiescent conditions at 37 °C, at an operating potential of +0.4 V, they produced an amperometric response to glucose in buffer solutions with a sensitivity of 26.4 nA/mM and a linear range of 0.45 to 9.0 mM. An optimal pH value of 8.5 was obtained under these conditions, and a value for activation energy of 40.55 kJ mol⁻¹ was calculated. In culture medium (pH 7.3), a sensitivity of 13 nA/mM was obtained and the response was linear up to 5 mM with a detection limit of 0.5 mM. The working concentration was up to 20 mM glucose with a precision of 11.3% for replicate biosensors (n = 4). The microband biosensors were applied to determine end-point glucose concentrations in culture medium by monitoring steady-state current responses 400 s after transfer of the biosensors into different sample solutions. In conjunction with cultures of HepG2 (human Caucasian hepatocyte carcinoma) cells, current responses obtained in 24-h supernatants showed an inverse correlation (R² = 0.98) with cell number, indicating that the biosensors were applicable for monitoring glucose metabolism by cells and of quantifying cell number. Glucose concentrations determined using the biosensor assay were in good agreement, for concentrations up to 20 mM, with those determined spectrophotometrically (R² = 0.99). This method of end-point glucose determination was used to provide an estimated rate of glucose uptake for HepG2 cells of 7.9 nmol/(10⁶ cells min) based on a 24-h period in culture.     

Receptor elements for biosensors in two ways of methylotrophic yeast immobilization

Receptor elements for biosensors based on Hansenula polymorpha NCYC 495 ln yeast cells for ethanol assay were developed using two ways of cell immobilization, i.e., physical adsorption on a glass fiber membrane and covalent binding on a modified nitrocellulose membrane. The linear diapason of ethanol assays for a biosensor based on yeast cells adsorbed on glass fiber was 0.05–1.18; for a biosensor based on yeasts immobilized on a nitrocellulose membrane, 0.2–1.53 mM. Receptor elements based on sorbed cells possessed 2.5 times higher long-term stability. The time response was 1.5 times less for cells immobilized using DEAE-dextran and benzoquinone. The results of ethyl alcohol assays using biosensors based on cells immobilized via adsorption and covalent binding, as well as using the standard areometric method, had high correlation coefficients (0.998 and 0.997, respectively, for the two ways of immobilization). The results indicate the possibility to consider the described models of receptor elements for biosensors as prototypes for experimental samples for practical use.     

Optimization of lab scale methanol production by <Emphasis Type="Italic">Methylosinus trichosporium</Emphasis> OB3b

Methylosinus trichosporium OB3b is a methanotrophic bacterium containing particulate methane monooxygenase (MMO), which catalyzes the hydroxylation of methane to methanol. The methanol is further oxidized to formaldehyde by methanol dehydrogenase (MDH). We developed a novel compulsory circulation diffusion system for cell cultivation. A methane/air mixture (1:1, v/v) was prepared in a tightly sealed gas reservoir and pumped into a nitrate mineral salt culture medium under optimal conditions (5 μM CuSO₄, pH 7.0, 30°C). Cells were harvested, washed, and resuspended (0.6 mg dry cells/mL) in a 500 mL flask in 100 mL of 10 mM phosphate buffer (pH 7.0) containing 100 mM NaCl and 1 mM EDTA as MDH inhibitors, and 20 mM sodium formate. A single 12 h batch reaction at 25°C yielded a final concentration of 13.2 mM methanol. The use of a repeated batch mode, in which the accumulated methanol was removed after each of three 8 h cycles over a 24 h period, showed a productivity of 2.17 μmol methanol/h/mg dry cell wt. Finally, a lab-scale reaction performed using a 3 L cylindrical reactor with a working volume of 1 L produced 13.7 mM methanol after 16 h. Our results identify a simple process for improving the productivity of biologically derived methanol and, therefore the utility of methane as an energy source.     

Direct electrochemistry of glucose oxidase and biosensing for glucose based on boron-doped carbon nanotubes modified electrode

Due to their unique physicochemical properties, doped carbon nanotubes are now extremely attractive and important nanomaterials in bioanalytical applications. In this work, selecting glucose oxidase (GOD) as a model enzyme, we investigated the direct electrochemistry of GOD based on the B-doped carbon nanotubes/glassy carbon (BCNTs/GC) electrode with cyclic voltammetry. A pair of well-defined, quasi-reversible redox peaks of the immobilized GOD was observed at the BCNTs based enzyme electrode in 0.1M phosphate buffer solution (pH 6.98) by direct electron transfer between the protein and the electrode. As a new platform in glucose analysis, the new glucose biosensor based on the BCNTs/GC electrode has a sensitivity of 111.57 microA mM(-1)cm(-2), a linear range from 0.05 to 0.3mM and a detection limit of 0.01mM (S/N=3). Furthermore, the BCNTs modified electrode exhibits good stability and excellent anti-interferent ability to the commonly co-existed uric acid and ascorbic acid. These indicate that boron-doped carbon nanotubes are the good candidate material for the direct electrochemistry of the redox-active enzyme and the construction of the related enzyme biosensors.     

Amperometric glucose biosensor based on multilayer films via layer-by-layer self-assembly of multi-wall carbon nanotubes, gold nanoparticles and glucose oxidase on the Pt electrode

A novel amperometric glucose biosensor based on the nine layers of multilayer films composed of multi-wall carbon nanotubes (MWCNTs), gold nanoparticles (GNp) and glucose oxidase (GOD) was developed for the specific detection of glucose. MWCNTs were chemically modified with the H₂SO₄–HNO₃ pretreatment to introduce carboxyl groups which were used to interact with the amino groups of poly(allylamine) (PAA) and cysteamine via 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide/N-hydroxysuccinimide cross-linking reaction, respectively. A cleaned Pt electrode was immersed in PAA, MWCNTs, cysteamine and GNp, respectively, followed by the adsorption of GOD, assembling the one layer of multilayer films on the surface of Pt electrode (GOD/GNp/MWCNTs/Pt electrode). Repeating the above process could assemble different layers of multilayer films on the Pt electrode. PBS washing was applied at the end of each assembly deposition for dissociating the weak adsorption. Film assembling and characterization were studied by transmission electron microscopy and quartz crystal microbalance, and properties of the resulting glucose biosensors were measured by electrochemical measurements. The marked electrocatalytic activity of Pt electrode based on multilayer films toward H₂O₂ produced during GOD enzymatic reactions with glucose permitted effective low-potential amperometric measurement of glucose. Taking the sensitivity and selectivity into consideration, the applied potential of 0.35 V versus Ag/AgCl was chosen for the oxidation detection of H₂O₂ in this work. Among the resulting glucose biosensors, the biosensor based on nine layers of multilayer films was best. It showed a wide linear range of 0.1–10 mM glucose, with a remarkable sensitivity of 2.527 μA/mM, a detection limit of 6.7 μM estimated at a signal-to-noise ratio of 3 and fast response time (within 7 s). Moreover, it exhibited good reproducibility, long-term stability and the negligible interferences of ascorbic acid, uric acid and acetaminophen. The study can provide a feasible approach on developing new kinds of oxidase-based amperometric biosensors, and can be used as an illustration for constructing various hybrid structures.     

Membrane entrapped Saccharomyces cerevisiae in a biosensor-like device as a generic rapid method to study cellular metabolism

We describe a new, faster and convenient method to study some metabolic characteristics — by the successful application of immobilized yeast cells (S. cerevisiae) in a microbial biosensor-like device. Microbial biosensors consist of microorganisms immobilized on the surface of a membrane or in a gel, in close contact with a transducer. Almost all works published to date have used biosensors for analyses in which a concentration-related property of the external medium is measured. A different approach is presented here; we have successfully used S. cerevisiae and a carbon dioxide electrode as the main components of a biosensor-like device, used as a proof of concept, for a system useful to characterize metabolic parameters of the microbial cells immobilized on a carbon dioxide electrode. The biosensor-like device we are presenting allows us to calculate Michaelis–Menten parameters related to the kinetics of transport and degradation of several carbohydrates (i.e., glucose, fructose, galactose, sucrose and xylose, with K_m(app) of 6.0, 5.8, 0.9, 2.0, and 147 mM, respectively), and the study of the kinetics of expression of non-constitutive proteins related to the transport and degradation of galactose.     

Nickel(II)-baicalein complex modified multiwall carbon nanotube paste electrode and its electrocatalytic oxidation toward glycine

A modified electrode, nickel(II)-baicalein complex modified multiwall carbon nanotube paste electrode (Ni(II)-BA-MWCNT-PE), has been fabricated by electrodepositing Ni(II)-BA complex on the surface of MWCNT-PE in alkaline solution. The Ni(II)-BA-MWCNT-PE exhibits the characteristic of improved reversibility and enhanced current responses of the Ni(III)/Ni(II) couple compared with Ni(II)-BA-carbon paste electrode (CPE). It also shows better electrocatalytic activity toward the oxidation of glycine than Ni(II)-MWCNT-PE. Kinetic parameters such as the electron transfer coefficient α, rate constant k_s of the electrode reaction, the diffusion coefficient D of glycine, and the catalytic rate constant k_cat of the catalytic reaction are determined. Moreover, the catalytic currents present linear dependence on the concentration of glycine from 20 μM to 1.0 mM by amperometry. The detection limit and sensitivity are 9.2 μM and 3.92 μA mM⁻¹, respectively. The modified electrode for glycine determination is of the property of simple preparation, fast response, and good stability.     

Label-free detection of bacterial RNA using polydiacetylene-based biochip

A novel acetylcholinesterase (AChE)/choline oxidase (ChOx) bienzyme amperometric acetylcholine biosensor based on gold nanoparticles (AuNPs) and multi-walled carbon nanotubes (MWCNTs) has been successfully developed by self-assembly process in combination of sol-gel technique. A thiolated aqueous silica sol containing MWCNTs and ChOx was first dropped on the surface of a cleaned Pt electrode, and then AuNPs were assembled with the thiolated sol-gel network. Finally, the alternate deposition of poly (diallyldimethylammonium chloride) (PDDA) and AChE was repeated to assemble different layers of PDDA-AChE on the electrode for optimizing AChE loading. Among the resulting biosensors, the biosensor based on two layers of PDDA-AChE multilayer films showed the best performance. It exhibited a wide linear range, high sensitivity and fast amperometric response, which were 0.005-0.4mM, 3.395 μA/mM, and within 15s, respectively. The biosensor showed long-term stability and acceptable reproducibility. More importantly, this study could provide a simple and effective multienzyme immobilization platform for meeting the demand of the effective immobilization enzyme on the electrode surface.     

Immobilization of glucose oxidase on graphene oxide for highly sensitive biosensors

Glucose oxidase (GOx) was immobilized onto graphene oxide (GRO) via three different preparation methods: enzyme adsorption (EA), enzyme adsorption and crosslinking (EAC), and enzyme adsorption, precipitation and crosslinking (EAPC). EAPC formulations, prepared via enzyme precipitation with 60% ammonium sulfate, showed 1,980 and 1,630 times higher activity per weight of GRO than those of EA and EAC formulations, respectively. After 59 days at room temperature, EAPC maintained 88% of initial activity, while EA and EAC retained 42 and 45% of their initial activities, respectively. These results indicate that the steps of precipitation and crosslinking in the EAPC formulation are critical to achieve high enzyme loading and stability of EAPC. EA, EAC and EAPC were used to prepare enzyme electrodes for use as glucose biosensors. Optimized EAPC electrode showed 93- and 25-fold higher sensitivity than EA and EAC, respectively. To further increase the sensitivity of EAPC electrode, multi-walled carbon nanotubes (MWCNTs) were mixed with EAPC for the preparation of enzyme electrode. Surprisingly, the EAPC electrode with additional 99.5 wt% MWCNTs showed 7,800-fold higher sensitivity than the EAPC electrode without MWCNT addition. Immobilization and stabilization of enzymes on GRO via the EAPC approach can be used for the development of highly sensitive biosensors as well as to achieve high enzyme loading and stability.     

Purification and characterization of methanol dehydrogenase of Methylobacterium nodulans rhizosphere phytosymbionts

Methanol dehydrogenase (MDH) of the facultative methylotrophic phytosymbiont Methylobacterium nodulans has been purified for the first time to an electrophoretically homogeneous state and characterized. The native protein with a molecular mass of 70 kDa consists of large (60 kDa) and small (6.5 kDa) subunits. The purified protein displayed a spectrum identical to that of pyrroloquinoline quinone (PQQ)-containing MDH, pI 8.7, pH optimum in the range 9–10. The enzyme was inactive in the absence of ammonium or methylamine and exhibited a wide substrate specificity with regard to C₁–C₅ alcohols with the high-est affinity to methanol (K _M = 70 μM), but it did not oxidize benzyl and secondary alcohols. The apparent K _M values to primary alcohols increased with the length of the carbon chain. The enzyme was characterized by a high stability level even in the absence of a substrate. An immobilized enzyme was used for amperometric methanol detection.     

Development of amperometric horseradish peroxidase based biosensors for clozapine and for the screening of thiol compounds

Two amperometric biosensors with immobilized horseradish peroxidase (HRP) were developed for the investigation of the clozapine drug oxidation and for thiols screening based on biosensor signal inhibition. The HRP was retained either in magnetized nanoporous silica microparticles (MMPs) or in a carbon paste (CP). The latter served for the carbon paste electrode while the MMPs were attracted in close proximity of a magnetized carbon electrode. The potential use of these configurations for drug oxidation and inhibition studies was illustrated by the enzymatic oxidation of clozapine (CLZ) in the presence of hydrogen peroxide. The biosensor signal corresponded to the electro-reduction of CLZ oxidation products namely a nitrenium ion (CLZox) generated by the enzyme HRP. Several thiols reactive towards CLZox were investigated and the biosensor signal inhibition (IC(50)) was comparatively determined. A protective effect of the nanoporous silica and carbon paste matrices towards HRP inactivation was inferred by comparing the biosensor inhibition results with those obtained with the free enzyme in solution.     

Enzymatic determination of BPA by means of tyrosinase immobilized on different carbon carriers

Different tyrosinase carbon paste modified electrodes to determine bisphenol A (BPA) concentration in aqueous solutions have been constructed. Variables examined were in the carbon paste composition and in particular: (i) the immobilized enzyme amount; (ii) the carbon type (powder, single or multi-walled nanotubes); (iii) the nature of the pasting oil (mineral oil, hexadecane and dodecane). For each biosensor type the amperometric response was evaluated with reference to the linear range and sensitivity. Constant reference has been made to the amperometric signals obtained, under the same experimental conditions, towards the catechol, a specific phenolic substrate for tyrosinase. The most efficient biosensors were those constructed by using the following composition for the carbon paste: 10% of tyrosinase, 45% of single wall carbon nanotubes (SWCN) and 45% of mineral oil. This biosensor formulation displayed the following electrochemical characteristics: a sensitivity equal to 138 microA/mM, LOD of 0.02 microM (based on three times the S/N ratio), linear range of 0.1-12 microM and response time of 6 min. This experimental work represents a first attempt at construction of a new carbon nanotube-tyrosinase based biosensor able to determine the concentration of BPA, one of the most ubiquitous and hazardous endocrine disruptors which can pollute the drinking and surface water, as well as many products of the food chain.     

Xanthine biosensor based on XO/AuNP/PtNP/MWCNT hybrid nanocomposite modified GCPE

A new xanthine (X) biosensors based on a hybrid nanocomposite containing multi-walled carbon nanotubes (MWCNT), Pt nanoparticles (PtNP) and gold nanoparticle (AuNP) was presented. X biosensor was fabricated by dropping AuNP/PtNP/MWCNT onto xanthine oxidase (XO) modified glassy carbon paste electrode (GCPE). Resulted XO/AuNP/PtNP/MWCNT/GCPE biosensor showed two linearity between 2.0 and 50 µM and 0.25 and 6.0 mM for X. RSD value was calculated as 2.46 (n = 5). Finally, the biosensor was applied to the X detection in synthetic serum samples and good recovery value was obtained.