Ultrastrong and high gas-barrier nanocellulose/clay-layered composites

Nanocellulose/montmorillonite (MTM) composite films were prepared from 2,2,6,6-tetramethylpiperidine-1-oxyl radical (TEMPO)-oxidized cellulose nanofibrils (TOCNs) with an aspect ratio of >200 dispersed in water with MTM nanoplatelets. The composite films were transparent and flexible and showed ultrahigh mechanical and oxygen barrier properties through the nanolayered structures, which were formed by compositing the anionic MTM nanoplatelet filler in anionic and highly crystalline TOCN matrix. A composite film with 5% MTM content had Young's modulus 18 GPa, tensile strength 509 MPa, work of fracture of 25.6 MJ m(-3), and oxygen permeability 0.006 mL μm m(-2) day(-1) kPa(-1) at 0% relative humidity, respectively, despite having a low density of 1.99 g cm(-3). As the MTM content in the TOCN/MTM composites was increased to 50%, light transmittance, tensile strength, and elongation at break decreased, while Young's modulus was almost unchanged and oxygen barrier property was further improved to 0.0008 mL μm m(-2) day(-1) kPa(-1).     

Transparent cellulose films with high gas barrier properties fabricated from aqueous alkali/urea solutions

Transparent and bendable regenerated cellulose films prepared from aqueous alkali (NaOH or LiOH)/urea (AU) solutions exhibit high oxygen barrier properties, which are superior to those of conventional cellophane, poly(vinylidene chloride), and poly(vinyl alcohol). Series of AU cellulose films are prepared from different cellulose sources (cotton linters, microcrystalline cellulose powder, and softwood bleached kraft pulp) for different dissolution and regeneration conditions. The oxygen permeabilities of these AU cellulose films vary widely from 0.003 to 0.03 mL μm m(-2) day(-1) kPa(-1) at 0% relative humidity depending on the conditions used to prepare the films. The lowest oxygen permeability is achieved for the AU film prepared from 6 wt % cellulose solution by regeneration with acetone at 0 °C. The oxygen permeabilities of the AU cellulose films are negatively correlated with their densities, and AU films prepared from solutions with high cellulose concentrations by regeneration in a solvent at low temperatures generally have low oxygen permeabilities. The AU cellulose films are, therefore, promising biobased packaging materials with high-oxygen barrier properties.     

Model films from native cellulose nanofibrils. Preparation, swelling, and surface interactions

Native cellulose model films containing both amorphous and crystalline cellulose I regions were prepared by spin-coating aqueous cellulose nanofibril dispersions onto silica substrates. Nanofibrils from wood pulp with low and high charge density were used to prepare the model films. Because the low charged nanofibrils did not fully cover the silica substrates, an anchoring substance was selected to improve the coverage. The model surfaces were characterized using atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). The effect of nanofibril charge density, electrolyte concentration, and pH on swelling and surface interactions of the model film was studied by quartz crystal microbalance with dissipation (QCM-D) and AFM force measurements. The results showed that the best coverage for the low charged fibrils was achieved by using 3-aminopropyltrimethoxysilane (APTS) as an anchoring substance and hence it was chosen as the anchor. The AFM and XPS measurements showed that the fibrils are covering the substrates. Charge density of the fibrils affected the morphology of the model surfaces. The low charged fibrils formed a network structure while the highly charged fibrils formed denser film structure. The average thickness of the films corresponded to a monolayer of fibrils, and the average rms roughness of the films was 4 and 2 nm for the low and high charged nanofibril films, respectively. The model surfaces were stable in QCM-D swelling experiments, and the behavior of the nanofibril surfaces at different electrolyte concentrations and pHs correlated with other studies and the theories of Donnan. The AFM force measurements with the model surfaces showed well reproducible results, and the swelling results correlated with the swelling observed by QCM-D. Both steric and electrostatic forces were observed and the influence of steric forces increased as the films were swelling due to changes in pH and electrolyte concentration. These films differ from previous model cellulose films due to their chemical composition (crystalline cellulose I and amorphous regions) and fibrillar structure and hence serve as excellent models for the pulp fiber surface.     

Flexible oxygen barrier films from spruce xylan

Arabinoglucuronoxylan was extracted from Norway spruce and films prepared by casting from aqueous solution. The sugar analysis and NMR confirmed that the spruce xylan was composed of arabinose, 4-O-methyl-glucuronic acid and xylose in a ratio of 1:2:11 respectively. Substitutions of 4-O-methyl-α-d-GlcpA at O₂ and of α-l-Araf at O₃ on the xylose backbone were found by NOE analysis. NOE cross-peaks indicated as well that there is at least one free xylose on the main chain present between two substitutions. Whether the distribution of side chains was random or in blocks was uncertain. The average molecular weight of the sample was determined by size exclusion chromatography to be 12,780 g/mol. Arabinoglucoronoxylan casting yielded transparent flexible films with an average stress at break of 55 MPa, strain at break of 2.7% and a Young's Modulus 2735 MPa. Wide-angle X-ray scattering analysis showed that the arabinoglucuronoxylan films were totally amorphous. Addition of sorbitol as plasticizer resulted in less strong but more flexible films (strain at break of 5%). Peaks of crystallinity could be seen in X-ray which corresponds to sorbitol crystallizing in distinct phases. The dynamic mechanical analysis showed that the arabinoglucuronoxylan film softened at a later relative humidity (80% RH) in comparison with plasticized films (60% RH). The films showed low oxygen permeability and thus have a potential application in food packaging.     

Design of functionalized cellulosic honeycomb films: site-specific biomolecule modification via "click chemistry"

Value-added materials from naturally abundant polymers such as cellulose are of significant importance. In particular, cellulosic open-framework structures with controlled chemical functionality of the internal surface have great potential in many biosensor applications. Although various cellulose derivatives can form porous honeycomb structured materials, solubility issues and problems with film formation exist. To address this, we have generated robust cellulosic open-framework structures that can be post-functionalized through site-specific modification. Regioselectively modified amphiphilic cellulose azides, 3-O-azidopropoxypoly(ethylene glycol)-2,6-di-O-thexyldimethylsilyl cellulosics, were synthesized, and honeycomb-patterned films were readily produced by the simple breath figures method. Changing the degree of polymerization (DP) of the pendent ethylene glycol (EG(DP)) groups from 22 to 4 increased the corresponding honeycomb film pore diameters from ~1.2 to ~2.6 μm, enabling the potential tuning of pore size. Moreover, these novel azido-functionalized honeycomb films were easily functionalized using Cu(I)-catalyzed alkyne-azide [2 + 3] cycloaddition reaction; biotin was "clicked" onto the azide functionalized cellulosic honeycomb films without any effect to the film structure. These results indicate this system may serve as a platform for the design and development of biosensors.     

Transport and tensile properties of compression-molded wheat gluten films

Mechanical and transport properties were assessed on wheat gluten films with a glycerol content of 25-40%, prepared by compression molding for 5-15 min at temperatures between 90 and 130 degrees C. Effects of storing the films up to 24 days, in 0 and 50% relative humidity (RH), were assessed by tensile measurements. The films were analyzed with respect to methanol zero-concentration diffusivity, oxygen permeability (OP), water vapor permeability (WVP), Cobb60 and sodium dodecyl sulfate (SDS) solubility coupled with sonication. The SDS solubility and methanol diffusivity were lower at the higher molding temperature. Higher glycerol content resulted in higher OP (90-95% RH), WVP, and Cobb60 values, due to the plasticizing and hygroscopic effects. Higher glycerol contents gave a lower fracture stress, lower Young's modulus, lower fracture strain, and less strain hardening. The mold time had less effect on the mechanical properties than mold temperature and glycerol content. The fracture stress and Young's modulus increased and the fracture strain decreased with decreasing moisture content.     

棉铃虫蛹期在极端湿度下的失水动态

研究了极端相对湿度 (0%、9%、22.5%、80%、90%和100%) 对棉铃虫Helicoverpa armigera蛹期发育、存活和水分动态的影响。发育蛹在25℃下,相对湿度≤9%时, 不能羽化;湿度为22.5%时,羽化率不足20%; 高湿不影响它们的存活。在同样温度下,湿度≥9%时,滞育蛹在一个月内都极少死亡;在此期间,滞育终止率随湿度降低而升高。各湿度处理组发育蛹和滞育蛹从1日龄起的累计失水率都与其日龄呈线性相关。三个低湿处理组发育蛹中死亡个体在死亡前的平均累计失水率都在32%以上。滞育蛹经0%湿度处理一个月,平均仅失水22.4%;在湿度≥90%时的同期失水率不超过3.6%。在30℃下,发育蛹在4 h内测定的表皮渗透力最大,分别是9.0(♀)和10.7(♂) μg/(cm²·h·mm Hg); 滞育蛹的相应值出现在2 h内, 分别为 4.7(♀)和5.4(♂) μg/(cm²·h·mm Hg)。     

Bi-Functional Biobased Packing of the Cassava Starch,Glycerol, Licuri Nanocellulose and Red Propolis

The aim of this study was to characterize and determine the bi-functional efficacy of active packaging films produced with starch (4%) and glycerol (1.0%), reinforced with cellulose nanocrystals (0–1%) and activated with alcoholic extracts of red propolis (0.4 to 1.0%). The cellulose nanocrystals used in this study were extracted from licuri leaves. The films were characterized using moisture, water-activity analyses and water vapor-permeability tests and were tested regarding their total phenolic compounds and mechanical properties. The antimicrobial and antioxidant efficacy of the films were evaluated by monitoring the use of the active films for packaging cheese curds and butter, respectively. The cellulose nanocrystals increased the mechanical strength of the films and reduced the water permeability and water activity. The active film had an antimicrobial effect on coagulase-positive staphylococci in cheese curds and reduced the oxidation of butter during storage.     

Partitioning of respiration between the gills and air-breathing organ in response to aquatic hypoxia and exercise in the pacific tarpon, Megalops cyprinoides

The evolution of air-breathing organs (ABOs) is associated not only with hypoxic environments but also with activity. This investigation examines the effects of hypoxia and exercise on the partitioning of aquatic and aerial oxygen uptake in the Pacific tarpon. The two-species cosmopolitan genus Megalops is unique among teleosts in using swim bladder ABOs in the pelagic marine environment. Small fish (58-620 g) were swum at two sustainable speeds in a circulating flume respirometer in which dissolved oxygen was controlled. For fish swimming at 0.11 m s(-1) in normoxia (Po2 = 21 kPa), there was practically no air breathing, and gill oxygen uptake was 1.53 mL kg(-0.67) min(-1). Air breathing occurred at 0.5 breaths min(-1) in hypoxia (8 kPa) at this speed, when the gills and ABOs accounted for 0.71 and 0.57 mL kg(-0.67) min(-1), respectively. At 0.22 m s(-1) in normoxia, breathing occurred at 0.1 breaths min(-1), and gill and ABO oxygen uptake were 2.08 and 0.08 mL kg(-0.67) min(-1), respectively. In hypoxia and 0.22 m s(-1), breathing increased to 0.6 breaths min(-1), and gill and ABO oxygen uptake were 1.39 and 1.28 mL kg(-0.67) min(-1), respectively. Aquatic hypoxia was therefore the primary stimulus for air breathing under the limited conditions of this study, but exercise augmented oxygen uptake by the ABOs, particularly in hypoxic water.     

Non-invasive measurement of oxygen partial pressure, lateral diffusion and chorioallantoic blood flow under the avian eggshell

We measured P(O2) under the shell of avian eggs indirectly, by sealing 0.05 mL glass tubes to the shell, sealing them with mercury and using an oxygen microelectrode to measure the contained gas that equilibrates with the gas in the shell membranes. This technique requires a smaller area of contact with the shell and a shorter equilibration period than established techniques, and allows measurements at several locations simultaneously and over a long period of time without endangering the embryo. P(O2) under the shell of chicken eggs decreased to 14.3 kPa on the day before hatching (day 19). P(O2) was unstable during late development and differences up to 3.1 kPa occurred transiently on opposite sides of the equator. By waxing the shell around sampling tubes, we estimated Krogh's coefficient for lateral oxygen diffusion in the shell membranes at 1.1 mmol cm(-1) d(-1) kPa(-1), a value about a third of a previous estimate. Sampling of gas under sufficiently large regions of waxed shell allowed indirect measurements of chorioallantoic venous P(O2), without affecting embryonic respiration. Venous P(O2) was 3.8 kPa on day 19. Assuming 14.3 kPa represents arterialized blood leaving the chorioallantois, it became possible to calculate the effective chorioallantoic blood flow rate, which was 3.5 mL min(-1) on day 19.     

Non-invasive measurement of oxygen partial pressure, lateral diffusion and chorioallantoic blood flow under the avian eggshell.

We measured P(O2) under the shell of avian eggs indirectly, by sealing 0.05 mL glass tubes to the shell, sealing them with mercury and using an oxygen microelectrode to measure the contained gas that equilibrates with the gas in the shell membranes. This technique requires a smaller area of contact with the shell and a shorter equilibration period than established techniques, and allows measurements at several locations simultaneously and over a long period of time without endangering the embryo. P(O2) under the shell of chicken eggs decreased to 14.3 kPa on the day before hatching (day 19). P(O2) was unstable during late development and differences up to 3.1 kPa occurred transiently on opposite sides of the equator. By waxing the shell around sampling tubes, we estimated Krogh's coefficient for lateral oxygen diffusion in the shell membranes at 1.1 mmol cm(-1) d(-1) kPa(-1), a value about a third of a previous estimate. Sampling of gas under sufficiently large regions of waxed shell allowed indirect measurements of chorioallantoic venous P(O2), without affecting embryonic respiration. Venous P(O2) was 3.8 kPa on day 19. Assuming 14.3 kPa represents arterialized blood leaving the chorioallantois, it became possible to calculate the effective chorioallantoic blood flow rate, which was 3.5 mL min(-1) on day 19.     

Retrostructural model to predict biomass formulations for barrier performance

Barrier performance and retrostructural modeling of the macromolecular components demonstrate new design principles for film formulations based on renewable wood hydrolysates. Hardwood hydrolysates, which contain a fair share of lignin coexisting with poly- and oligosaccharides, offer excellent oxygen-barrier performance. A Hansen solubility parameter (HSP) model has been developed to convert the complex hydrolysate structural compositions into relevant matrix oxygen-permeability data allowing a systematic prediction of how the biomass should be formulated to generate an efficient barrier. HSP modeling suggests that the molecular packing ability plays a key role in the barrier performance. The actual size and distribution of free volume holes in the matrices were quantified in the subnanometer scale with Positron annihilation lifetime spectroscopy (PALS) verifying the affinity-driven assembly of macromolecular segments in a densely packed morphology and regulating the diffusion of small permeants through the matrix. The model is general and can be adapted to determine the macromolecular affinities of any hydrolysate biomass based on chemical composition.     

Protection of active aroma compound against moisture and oxygen by encapsulation in biopolymeric emulsion-based edible films

Edible films made of iota-carrageenans display interesting advantages: good mechanical properties, stabilization of emulsions, and reduction of oxygen transfers. Moreover, the addition of lipids to iota-carrageenan-based films to form emulsified films decreases the transfer of water vapor and can be considered to encapsulate active molecules as flavors. The aim of this study was to better understand the influence of the composition and the structure of the carrageenan-based film matrices on its barrier properties and thus on its capacity to encapsulate and to protect active substances encapsulated. Granulometry, differential scanning calorimetry, and Fourier transform infrared spectroscopy characterizations of films with or without flavor and/or fat showed that the flavor compound modifies the film structure because of interactions with the iota-carrageenan chains. The study of the water vapor permeability (WVP), realized at 25 and 35 degrees C and for three relative humidity differentials (30-100%, 30-84%, 30-75%), showed that the flavor compound increases significantly the WVP, especially for the weaker gradients, but has no effect on the oxygen permeability. This study brings new understanding of the role of carrageenan as a film matrix and on its capacity to protect encapsulated flavors.     

Characterization of films made with chayote tuber and potato starches blending with cellulose nanoparticles

The aim of this study was to characterize chayotextle starch films reinforced with cellulose (C) and cellulose nanoparticle (CN) (at concentrations of 0.3%, 0.5%, 0.8% and 1.2%), using thermal, mechanical, physicochemical, permeability, and water solubility tests. C was acid-treated to obtain CN. The films were prepared by casting; potato starch and C were used as the control. The solubility of the starch films decreased with the addition of C and CN compared with its respective film without C and CN. No statistical difference (α = 0.05) was found in the films added with different concentrations of C and CN. In general, the mechanical properties were improved with the addition of C and CN, and higher values of tensile strength and elastic modulus were determined in the films reinforced with CN. The melting temperature and enthalpy increased with the addition of C and CN, and the values of both thermal parameters were higher in the films with CN than with C; the enthalpy value of the film decreased when the concentration of C or CN increased in the composite. Low concentration of C and CN is better distributed in the matrix film. The addition of C and CN in the starch films improved some mechanical, barrier, and functional properties.     

山地枣树茎直径对不同生态因子的响应

以山地梨枣为试材,进行了枣树茎直径对土壤水势(WPs)、太阳辐射(Rs)、气温(Ta)、空气相对湿度(RH)等生态因子的响应试验研究。试验共设4个WPs区间的处理,连续测定枣树茎直径及不同生态因子的动态变化。结果表明:在果实膨大期,在-41—-390 kPa范围内,WPs越高的处理,其枣树茎直径(TD)越大;不同处理间枣树最大茎直径(MXTD)存在显著性差异,较高的WPs区间有利于茎直径的增加;MXTD是该期较为适宜的水分信息诊断指标。晴天时,茎直径日收缩幅度大;雨天白天时,茎直径基本处于同一水平,收缩不明显。TD与RH呈极显著正相关,与Ta呈极显著负相关关系,与Rs间无显著相关关系,RH与Ta是影响茎直径变化的最主要气象因子。综合考虑,枣树茎直径的微变化同时受到各种生态因子的影响,尤以RH、Ta、WPs的影响更为显著;WPs高时,WPs为影响茎直径变化的主要因子;WPs低时,RH成为影响茎直径变化的主要因子。     

Growth of human keratinocytes and fibroblasts on bacterial cellulose film

Thin films of bacterial cellulose (BC) from a nata de coco culture system were developed, characterized, and investigated for the growth of human keratinocytes and fibroblasts. The average pore diameter and total surface area of the dried BC films estimated by BET were 224 A and 12.62 m(2)/g, respectively. With an film thickness of 0.12 mm, the average tensile strength and break strain of the dried films were 5.21 MPa and 3.75%, whereas those of the wet films were 1.56 MPa and 8.00%, respectively. The water absorption capacity of air-dried film was 5.09 g water/g dried films. For uses in the therapy of skin wounds, the potential biological mechanism of action of BC film was evaluated by using human keratinocytes and fibroblasts. Our results were the first direct demonstration that BC film supported the growth, spreading, and migration of human keratinocytes but not those of human fibroblasts. Expressions of E-cadherin and the alpha-3 chain of laminin confirmed the phenotype of human keratinocytes on BC film.     

A simple and novel method for recovering adenovirus 41 in small volumes of source water

Aim: A new procedure was developed to recover adenovirus 41 in small volumes (1 l) of water samples based on adsorption, elution and evaporation. Methods and Results: One litre of source water seeded with adenovirus 41 was adjusted to pH 3·5 and filtered using a large pore size (8·0 μm) negatively charged membrane filter (SCWP, 47 mm diameter, made of mixed‐cellulose esters). Then, the filter was eluted using 4 ml of 1·5% beef extract plus 0·75% glycerol (pH 9·0). The eluate was reconcentrated to 0·1 ml or less volumes through evaporation assisted with air flow and heating at 55°C. Recovery of adenovirus 41 reached 55% under tested conditions and reduced filtration time by 85% in contrast to the widely used small pore size filter (0·45 μm pore size, 47 mm diameter). Reconcentration by evaporation achieved approx. 86·8% recovery from source water in approx. 1 h at no cost. Conclusion: The virus concentration method developed in this study is simple and cost‐effective and can be used to efficiently recover adenovirus 41 from turbid water samples. Significance and Impact of the Study: The procedure developed can be applied to detect adenovirus 41 in source water within hours of sampling. In addition, this is the first application of evaporation to concentrate viruses in water samples.     

Transparent films based on PLA and montmorillonite with tunable oxygen barrier properties

Polylactide (PLA) is viewed as a potential material to replace synthetic plastics (e.g., poly(ethylene terephthalate) (PET)) in food packaging, and there have been a number of developments in this direction. However, for PLA to be competitive in more demanding uses such as the packaging of oxygen-sensitive foods, the oxygen permeability coefficient (OP) needs to be reduced by a factor of ~10. To achieve this, a layer-by-layer (Lbl) approach was used to assemble alternating layers of montmorillonite clay and chitosan on extruded PLA film surfaces. When 70 bilayers were applied, the OP was reduced by 99 and 96%, respectively, at 20 and 50% RH. These are, to our knowledge, the best improvements in oxygen barrier properties ever reported for a PLA/clay-based film. The process of assembling such multilayer structures was characterized using a quartz crystal microbalance with dissipation monitoring. Transmission electron microscopy revealed a well-ordered laminar structure in the deposited multilayer coatings, and light transmittance results demonstrated the high optical clarity of the coated PLA films.     

Effect of transglutaminase treatment on the properties of cast films of soy protein isolates

The objective of this work was to investigate the effect of microbial transglutaminase (MTGase) treatment on the properties and microstructures of soy protein isolate (SPI) films cast with 0.6 plasticizer per SPI (gg(-1)) of glycerol, sorbitol and 1:1 mixture of glycerol and sorbitol, respectively. Tensile strength (TS), elongation at break (EB), water vapor transmission rate (WVTR) or water vapor permeability (WVP), moisture content (MC), total soluble matter (TSM), lipid barrier property and surface hydrophobicity of control and MTGase-treated films were evaluated after conditioning film specimens at 25 degrees C and 50% relative humidity (RH) for 48 h. The treatment by 4 units per SPI (Ug(-1)) of MTGase increased the TS and surface hydrophobicity by 10-20% and 17-56%, respectively, and simultaneously significantly (P< or =0.05) decreased the E, MC and transparency. The WVTR or TSM of SPI films seemed to be not significantly affected by enzymatic treatment (P>0.05). The MTGase treatment also slowed down the moisture loss rate of film-forming solutions with various plasticizers during the drying process, which was consistent with the increase of surface hydrophobicity of SPI films. Microstructural analyses indicated that the MTGase-treated films of SPI had a rougher surface and more homogeneous or compact cross-section compared to the controls. These results suggested that the MTGase treatment of film-forming solutions of SPI prior to casting could greatly modify the properties and microstructures of SPI films.     

Towards Biomimicking Wood: Fabricated Free-standing Films of Nanocellulose,Lignin, and a Synthetic Polycation

Woody materials are comprised of plant cell walls that contain a layered secondary cell wall composed of structural polymers of polysaccharides and lignin. Layer-by-layer (LbL) assembly process which relies on the assembly of oppositely charged molecules from aqueous solutions was used to build a freestanding composite film of isolated wood polymers of lignin and oxidized nanofibril cellulose (NFC). To facilitate the assembly of these negatively charged polymers, a positively charged polyelectrolyte, poly(diallyldimethylammomium chloride) (PDDA), was used as a linking layer to create this simplified model cell wall. The layered adsorption process was studied quantitatively using quartz crystal microbalance with dissipation monitoring (QCM-D) and ellipsometry. The results showed that layer mass/thickness per adsorbed layer increased as a function of total number of layers. The surface coverage of the adsorbed layers was studied with atomic force microscopy (AFM). Complete coverage of the surface with lignin in all the deposition cycles was found for the system, however, surface coverage by NFC increased with the number of layers. The adsorption process was carried out for 250 cycles (500 bilayers) on a cellulose acetate (CA) substrate. Transparent free-standing LBL assembled nanocomposite films were obtained when the CA substrate was later dissolved in acetone. Scanning electron microscopy (SEM) of the fractured cross-sections showed a lamellar structure, and the thickness per adsorption cycle (PDDA-Lignin-PDDA-NC) was estimated to be 17 nm for two different lignin types used in the study. The data indicates a film with highly controlled architecture where nanocellulose and lignin are spatially deposited on the nanoscale (a polymer-polymer nanocomposites), similar to what is observed in the native cell wall.