Kinetic and equilibrium models for biosorption of Cr(VI) on chemically modified seaweed,Cystoseira indica

The biosorption data of hexavalent chromium by marine brown algae Cystoseira indica, which was chemically modified by crosslinking with epichlorohydrin (CB1, CB2), or oxidized by potassium permanganate (CB3), or only washed with distilled water (RB), has been used for kinetic studies based on fractional power, Elovich, pseudo-first order and pseudo-second order rate expressions. Five three parameter biosorption isotherm models, viz. Redlich–Peterson, Sips, Khan, Radke–Prausnitz and Toth are tested for their applicability apart from 6 two-parameter models. Non-linear curve fitting procedure was adopted for fitting the kinetic as well as equilibrium data in the kinetic and isotherm models and for the determination of parameters. The time-dependent Cr(VI) biosorption data were well-described by pseudo-second-order kinetic model. The intraparticle diffusion study revealed that film diffusion might be involved in Cr(VI) biosorption in the present case. Among the two-parameter models, the Langmuir model produces the best fit, while, among the three-parameter models, the best fit is produced by the Khan model, for the biosorption of Cr(VI) on all the four biosorbents studied.     

Biosorption of Pb(II) and Cr(III) from aqueous solution by lichen (Parmelina tiliaceae) biomass

The biosorption characteristics of Pb(II) and Cr(III) ions from aqueous solution using the lichen (Parmelina tiliaceae) biomass were investigated. Optimum biosorption conditions were determined as a function of pH, biomass dosage, contact time, and temperature. Langmuir, Freundlich and Dubinin-Radushkevich (D-R) models were applied to describe the biosorption isotherm of the metal ions by P. tiliaceae biomass. Langmuir model fitted the equilibrium data better than the Freundlich isotherm. The monolayer biosorption capacity of P. tiliaceae biomass for Pb(II) and Cr(III) ions was found to be 75.8 mg/g and 52.1mg/g, respectively. From the D-R isotherm model, the mean free energy was calculated as 12.7 kJ/mol for Pb(II) biosorption and 10.5 kJ/mol for Cr(III) biosorption, indicating that the biosorption of both metal ions was taken place by chemical ion-exchange. The calculated thermodynamic parameters (delta G degrees , delta H degrees and delta S degrees ) showed that the biosorption of Pb(II) and Cr(III) ions onto P. tiliaceae biomass was feasible, spontaneous and exothermic under examined conditions. Experimental data were also tested in terms of biosorption kinetics using pseudo-first-order and pseudo-second-order kinetic models. The results showed that the biosorption processes of both metal ions followed well pseudo-second-order kinetics.     

Biosorption behavior of heavy metals in bioleaching process of MSWI fly ash by Aspergillus niger

In this study, it was considered that the biosorption of heavy metals by biomass might occur during the bioleaching of fly ash. This work is focused on the biosorption behavior of Al, Fe, Pb and Zn by Aspergillus niger during the bioleaching process. The fungal biomass was contacted with heavy metals solution which extracted from fly ash by using gluconic acid as leaching agent. The equilibrium time for biosorption was about 120 min. The biosorption experiment data at initial pH 6.5 was used to fit the biosorption kinetics and isotherm models. The results indicated that the biosorption of Al, Fe and Zn by A. niger biomass were well described by the pseudo-first order kinetic model. The pseudo-second order kinetic model was more suitable for that of Pb. The Langmuir isotherm model could well describe the biosorption of Fe, Pb and Zn while the Freundlich model could well describe the biosorption of Al. Furthermore, the biosorption of metal ions decreased evidently in the presence of fly ash as compared to that in the absence of fly ash. This research showed that although the biomass sorption occurred during the bioleaching process, it did not inhibit the removal of Al, Fe, Pb and Zn evidently from fly ash.     

Biosorption of nickel(II) ions by baker's yeast: kinetic, thermodynamic and desorption studies

In this study, the biosorption of nickel(II) ion on deactivated protonated yeast was investigated as a function of temperature at different initial metal ion concentrations. The effect of temperature on the sorption was more significant at lower nickel(II) ion concentrations compared to higher concentrations. The protonated yeast biomass exhibited the highest nickel(II) ion uptake capacity at 27 degrees C at an initial nickel(II) ion concentration of 400mg/l and an initial pH of 6.75. The biosorption capacity decreased from 9.8 to 9.3mg/g at an initial nickel(II) ion concentration of 400mg/l, while at a lower initial concentration of 100mg/l, it decreased from 8.2 to 4.9 mg/g, as the temperature was increased from 27 degrees C to 60 degrees C. The equilibrium data fit better to the Freundlich and Redlich-Peterson isotherm models compared to the Langmuir model in the concentration range studied (10-400mg/l). Kinetic models applied to the sorption data at different temperatures showed that nickel(II) ion uptake process followed the pseudo-second order rate model and the adsorption rate constants decreased with increasing temperature. The activation energy of biosorption (Ea) was determined to be -13.3 kJ/mol using the pseudo-second order rate constants. The results indicated that the biosorption of nickel(II) ion on to baker's yeast was spontaneous and exothermic in nature. Desorption studies revealed that the protonated yeast biomass can be regenerated using 0.1N HCl and reused.     

Biosorption of Cd(II) and Pb(II) onto brown seaweed, Lobophora variegata (Lamouroux): kinetic and equilibrium studies

The present work deals with the biosorption performance of raw and chemically modified biomass of the brown seaweed Lobophora variegata for removal of Cd(II) and Pb(II) from aqueous solution. The biosorption capacity was significantly altered by pH of the solution delineating that the higher the pH, the higher the Cd(II) and Pb(II) removal. Kinetic and isotherm experiments were carried out at the optimal pH 5.0. The metal removal rates were conspicuously rapid wherein 90% of the total sorption occurred within 90 min. Biomass treated with CaCl₂ demonstrated the highest potential for the sorption of the metal ions with the maximum uptake capacities i.e. 1.71 and 1.79 mmol g⁻¹ for Cd(II) and Pb(II), respectively. Kinetic data were satisfactorily manifested by a pseudo-second order chemical sorption process. The process mechanism consisting of both surface adsorption and pore diffusion was found to be complex. The sorption data have been analyzed and fitted to sorption isotherm of the Freundlich, Langmuir, and Redlich–Peterson models. The regression coefficient for both Langmuir and Redlich–Peterson isotherms were higher than those secured for Freundlich isotherm implying that the biosorption system is possibly monolayer coverage of the L. variegata surface by the cadmium and lead ions. FT-IR studies revealed that Cd(II) and Pb(II) binding to L. variegata occurred primarily through biomass carboxyl groups accompanied by momentous interactions of the biomass amino and amide groups. In this study, we have observed that L. variegata had maximum biosorption capacity for Cd(II) and Pb(II) reported so far for any marine algae. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Biosorption of Nickel(II) from aqueous solution by the fungal mat of Trametes versicolor (rainbow) biomass: equilibrium, kinetics, and thermodynamic studies

This study investigates the equilibrium, kinetics and thermodynamics of Nickel(II) biosorption from aqueous solution by the fungal mat of Trametes versicolor (rainbow) biomass. The optimum biosorption conditions like pH, contact time, biomass dosage, initial metal ion concentration and temperaturewere determined in the batch method. The biosorbent was characterized by FTIR, SEM and BET surface area analysis. The experimental data were analyzed in terms of pseudo-first-order, pseudo-secondorder and intraparticle diffusion kinetic models, further it was observed that the biosorption process of Ni(II) ions closely followed pseudo-second-order kinetics. The equilibrium data of Ni(II) ions at 303, 313, and 323 K were fitted to the Langmuir and Freundlich isotherm models. Langmuir isotherm provided a better fit to the equilibrium data andthe maximum monolayer biosorption capacity of the T. versicolor(rainbow) biomass for Ni(II) was 212.5 mg/g at pH 4.0. The calculated thermodynamic parameters, ΔG^○, ΔH^○, and ΔS^○, demonstrated that the biosorption of Ni(II) ions onto the T. versicolor (rainbow) biomass was feasible, spontaneous and endothermic at 303 ～ 323 K. The performance of the proposed fungal biosorbent was also compared with that of many other reported sorbents for Nickel(II) removal and it was observed that the proposed biosorbent is effective in terms of its high sorption capacity.     

The biosorption of heavy metals from aqueous solution by Spirogyra and Cladophora filamentous macroalgae

The aim of this research was to develop a low cost adsorbent for wastewater treatment. The prime objective of this study was to search for suitable freshwater filamentous algae that have a high heavy metal ion removal capability. This study evaluated the biosorption capacity from aqueous solutions of the green algae species, Spirogyra and Cladophora, for lead (Pb(II)) and copper (Cu(II)). In comparing the analysis of the Langmuir and Freundlich isotherm models, the adsorption of Pb(II) and Cu(II) by these two types of biosorbents showed a better fit with the Langmuir isotherm model. In the adsorption of heavy metal ions by these two types of biosorbents, chemical and physical adsorption of particle surfaces was perhaps more significant than diffusion and adsorption between particles. Continuous adsorption-desorption experiments discovered that both types of biomass were excellent biosorbents with potential for further development.     

Biosorption of Malachite Green from aqueous solutions onto aerobic granules: kinetic and equilibrium studies

Batch experiments were conducted to study the biosorption characteristics of a cationic dye, Malachite Green (MG), onto aerobic granules. Effects of pH, aerobic granule dosage, contact time and solution temperature on MG biosorption by aerobic granules were evaluated. Simultaneity the thermodynamic analysis was also performed. The results showed that alkaline pH was favorable for the biosorption of MG and chemisorption seemed to play a major role in the biosorption process. Kinetic studies indicate that MG biosorption on aerobic granules in the system follows the pseudo-second order kinetics. The equilibrium time was 60 min for both 50 and 60 mg/L and 120 min for both 70 and 80 mg/L MG concentrations, respectively. Moreover, the experimental equilibrium data have been analyzed using the linearized forms of Langmuir, Freundlich, and Redlich-Peterson isotherms and the Langmuir isotherm was found to provide the best theoretical correlation of the experimental data for the biosorption of MG. The monolayer biosorption (saturation) capacities were determined to be 56.8 mg of MG per gram of aerobic granules at 30 degrees C. Thermodynamic analysis show that biosorption follows an endothermic path of the positive value of Delta H( composite function) and spontaneous with negative value of Delta G( composite function).     

Performance of durian shell waste as high capacity biosorbent for Cr(VI) removal from synthetic wastewater

The capability of durian shell waste biomass as a novel and potential biosorbent for Cr(VI) removal from synthetic wastewater was studied. The adsorption study was performed in batch mode at different temperatures and pH. Langmuir and Freundlich isotherm models fit the equilibrium data very well (R² > 0.99). The maximum biosorption capacity of durian shell was 117 mg/g. On modeling its kinetic experimental data, the pseudo-first order prevails over the pseudo-second order model. Thermodynamically, the characteristic of Cr-biosorption process onto durian shell surface was spontaneous, irreversible and endothermic.     

Using biosorption to enrich the biomass of <Emphasis Type="Italic">Chlorella vulgaris </Emphasis>with microelements to be used as mineral feed supplement

The paper discusses biosorption of Cr(III), Cu(II), Mn(II), Zn(II) and Co(II) to the biomass of Chlorella vulgaris, to produce a biologically bound, concentrated form of microelements. The kinetics of biosorption was described with a pseudo-second order equation and equilibrium with the Langmuir isotherm. The mechanism of biosorption was identified as cation-exchange with alkaline metals. Cation-exchange capacity was evaluated as 4.07 meq g⁻¹. The effect of operation conditions, pH and temperature, on biosorption performance was investigated and the best operation conditions for biosorption were selected (pH 5, temperature 25 °C). The maximum sorption capacity of microelements was determined in single-metal system at pH 5 and 25 °C: Zn(II) 3.30 meq g⁻¹, Cu(II) 1.77 meq g⁻¹, Co(II) 1.75 meq g⁻¹, Cr(III) 1.74 meq g⁻¹, Mn(II) 0.764 meq g⁻¹. Biosorption experiments were also carried out in multi-metal system. The biomass of C. vulgaris enriched with microelements via the process of biosorption in both single- and multi-metal system was discussed in terms of preparation of feed supplement for laying hens and piglets. The experiments showed that 1 kg of conventional feed for laying hens can be supplemented with 0.20 g of the biomass enriched with microelements and for piglets with 0.15 g of the preparation.     

Characterization and lead(II) ions removal of modified Punica granatum L. peels

The aim of the present study was to enhance the biosorption capacity of a waste biomass of Punica granatum L. peels (PGL) using various chemical modification agents. Among these agents, hexamethylenediamine (HMDA) indicated the best performance with regard to the improvement of lead(II) ions removal from aqueous solution. The characterization of HMDA-modified P. granatum L. peels (HMDA-PGL) was achieved by using elemental analysis, FT-IR, thermogravimetric (TG) analysis and zeta potential measurement techniques. Based on FT-IR study, the chemical modification of P. granatum L. peels take place with its carboxyl, carbonyl, hydroxyl, etc. groups and these groups are responsible for the biosorption of lead(II) ions onto modified biomass. Biosorption equilibrium and kinetic data fitted well the Langmuir isotherm and the pseudo-second-order kinetic models, respectively. The highest biosorption capacity obtained from Langmuir isotherm model was 371.36 mg g^?1. Biosorption process was spontaneous and endothermic in nature according to the thermodynamic results and it quickly reached the equilibrium within 60 minutes. The validity of kinetic models used in this study can be quantitatively tested by using a normalized standard deviation Δq(%).     

Evaluation of the marine algae Ulva fasciata and Sargassum sp. for the biosorption of Cu(II) from aqueous solutions

In this study, the adsorption properties of two different marine algae (Ulva fasciata (green algae) and Sargassum sp. (brown algae)) were investigated. Equilibrium isotherms and kinetics were studied to evaluate the relative ability of the two algae to sequester Cu(II) from aqueous solutions. The maximum biosorption capacity obtained was 73.5 mg g(-1) for U. fasciata and 72.5 mg g(-1) for Sargassum sp. at a solution pH of 5.5 +/- 0.5. A significant fraction of the total copper(II) uptake was achieved within 30 min. The copper(II) uptake by the biosorbents was best described by pseudo-second-order rate model.     

Application of Freundlich and Langmuir models to multistage purification process to remove heavy metal ions by using Schizomeris leibleinii

The adsorption of iron(III), lead(II) and cadmium(II) ions onto Schizomeris leibleinii, a green alga, was studied with respect to initial pH, temperature, initial metal ion and biomass concentration to determine the optimum adsorption conditions. Optimum initial pH for iron(III), lead(II) and cadmium(II) ions were 2.5, 4.5 and 5.0 at optimum temperature 30°C, respectively. The initial adsorption rates increased with increasing initial iron(III), lead(II) and cadmium(II) ion concentrations up to 100, 100 and 150 mg l⁻¹, respectively. The Freundlich and Langmuir adsorption isotherms were developed at various initial pH and temperature values. The adsorption of these metal ions to S. leibleinii was investigated in a two-stage mixed batch reactor. The residual metal ion concentrations (C_eq) at equilibrium at each stage for a given ‘quantity of dried algae (X₀)/volume of solution containing heavy metal ion (V₀)’ ratio were calculated using Freundlich and Langmuir isotherm constants. The experimental biosorption equilibrium data for iron(III), lead(II) and cadmium(II) ions were in good agreement with those calculated by both Freundlich and Langmuir models. The adsorbed iron(III), lead(II) and cadmium(II) ion concentrations increased with increasing X₀/V₀ ratios while the adsorbed metal quantities per unit mass of dried algae decreased.     

Cadmium uptake by algal biomass in batch and continuous (CSTR and packed bed column) adsorbers

In this work, the properties of marine algae Gelidium, algal waste from agar extraction industry and a composite material were investigated for cadmium(II) biosorption. Equilibrium experiments were performed at three pH values (4, 5.3 and 6.5). Equilibrium data were well described by the Langmuir and Langmuir–Freundlich isotherms. Two models predicting the pH influence in the cadmium biosorption (discrete and continuous models) have been developed in order to better describe the equilibrium. The continuous model also considers a heterogeneous distribution of carboxylic groups, determined by potentiometric titration. The results of batch kinetic experiments performed at different pH values were well fitted by two mass transfer models and the homogeneous diffusion coefficients for the cadmium ions inside the biosorbent were obtained. Continuous stirred tank reactor (CSTR) and packed bed column configurations were also examined for the biosorption of cadmium ions. A strong acid (0.1 M HNO₃) was used as eluant to regenerate the biosorbents in the column. Several mass transfer models were applied with success to describe the biosorption process in batch mode, CSTR and fixed bed column.     

Biosorption of cadmium (II) ions by immobilized cells of Pycnoporus sanguineus from aqueous solution

Biosorption of cadmium (II) ions from aqueous solution onto immobilized cells of Pycnoporus sanguineus (P. sanguineus) was investigated in a batch system. Equilibrium and kinetic studies were conducted by considering the effect of pH, initial cadmium (II) concentration, biomass loading and temperature. Results showed that the uptake of cadmium (II) ions increased with the increase of initial cadmium (II) concentration, pH and temperature. Langmuir, Freundlich and Redlich-Peterson isotherm models were used to analyze the equilibrium data at different temperatures. Langmuir isotherm model described the experimental data well followed by Redlich-Peterson and Freundlich isotherm models. Biosorption kinetics data were fitted using pseudo-first, pseudo-second-order and intraparticle diffusion. It was found that the kinetics data fitted well the pseudo-second-order followed by intraparticle diffusion. Thermodynamic parameters such as standard Gibbs free energy (Delta G0), standard enthalpy (Delta H0) and standard entropy (Delta S0) were evaluated. The result showed that biosorption of cadmium (II) ions onto immobilized cells of P. sanguineus was spontaneous and endothermic nature.     

Bioremediation potential of a widespread industrial biowaste as renewable and sustainable biosorbent for synthetic dye pollution

In this study, a model synthetic azo dye (Basic red 46) bioremoval by Carpinus betulus sawdust as inexpensive, eco-friendly, and sustainable biosorbent from aqueous solution was examined in a batch biosorption system. The effective environmental parameters on the biosorption process, such as the value of pH, amount of biosorbent, initial dye concentration and contact time were optimized using classical test design. The possible dye-biosorbent interaction was determined by Fourier Transform Infrared Spectroscopy (FTIR) and Scanning Electron Microscopy (SEM). The equilibrium, thermodynamic, and kinetic studies for the biosorption of Basic red 46 onto the sawdust biomass were performed. In addition, a single-stage batch dye biosorption system was also designed. The dye biosorption yield of biosorbent was significantly influenced by the change of operating variables. The experimental data were best described by the Freundlich isotherm model and both the pseudo-first-order kinetic and the pseudo-second-order kinetic models. Thermodynamic research indicated that the biosorption of dye was feasible and spontaneous. Based on the Langmuir isotherm model, the biosorbent was found to have a maximum biosorption potential higher than many other biosorbents in the literature (264.915?mg g^?1). Thus, this investigation presents a novel green option for the assessment of waste sawdust biomass as a cheap and effective biosorbent material.     

Utilization of unconventional lignocellulosic waste biomass for the biosorption of toxic triphenylmethane dye malachite green from aqueous solution

Biosorption potential of novel lignocellulosic biosorbents Musa sp. peel (MSP) and Aegle marmelos shell (AMS) was investigated for the removal of toxic triphenylmethane dye malachite green (MG), from aqueous solution. Batch experiments were performed to study the biosorption characteristics of malachite green onto lignocellulosic biosorbents as a function of initial solution pH, initial malachite green concentration, biosorbents dosage, and temperature. Biosorption equilibrium data were fitted to two and three parameters isotherm models. Three-parameter isotherm models better described the equilibrium data. The maximum monolayer biosorption capacities obtained using the Langmuir model for MG removal using MSP and AMS was 47.61 and 18.86 mg/g, respectively. The biosorption kinetic data were analyzed using pseudo-first-order, pseudo-second-order, Elovich and intraparticle diffusion models. The pseudo-second-order kinetic model best fitted the experimental data, indicated the MG biosorption using MSP and AMS as chemisorption process. The removal of MG using AMS was found as highly dependent on the process temperature. The removal efficiency of MG showed declined effect at the higher concentrations of NaCl and CaCl₂. The regeneration test of the biosorbents toward MG removal was successful up to three cycles.     

Ni (II) adsorption onto Chrysanthemum indicum: Influencing factors,isotherms, kinetics,and thermodynamics

The study explores the adsorption potential of Chrysanthemum indicum biomass for nickel ion removal from aqueous solution. C. indicum flowers in raw (CIF-I) and biochar (CIF-II) forms were used as adsorbents in this study. Batch experiments were conducted to ascertain the optimum conditions of solution pH, adsorbent dosage, contact time, and temperature for varying initial Ni(II) ion concentrations. Surface area, surface morphology, and functionality of the adsorbents were characterized by Brunauer, Emmett, and Teller (BET) surface analysis, scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), and Fourier transform infrared spectroscopy (FTIR). Adsorption kinetics were modeled using pseudo-first order, pseudo-second order, Elovich, intraparticle diffusion, Bangham's, and Boyd's plot. The equilibrium data were modeled using Langmuir, Freundlich, Temkin, and Dubinin–Radushkevich (D-R) isotherm models. Experimental data provided the best fit to pseudo-second-order kinetic model and Langmuir isotherm model for the adsorption of Ni(II) ion on both CIF-I and CIF-II with maximum adsorption capacities of 23.97 and 44.02 mg g^?1, respectively. Thermodynamic analysis of the data proved the process to be spontaneous and endothermic in nature. Desorption studies were conducted to evaluate the possibility of reusing the adsorbents. Findings of the present study provide substantial evidence for the use of C. indicum flower as an eco-friendly and potential adsorbent for the removal of Ni(II) ions from aqueous solution.