Separation of microcystins by capillary electrochromatography in monolithic columns

Contribution on microcystin variant analysis by capillary electrochromatography (CEC) with easily affordable spectrophotometric detection is presented. Two types of reversed-phase capillary columns formed by inorganic or organic polymer monoliths were prepared for this purpose. The analyses were performed isocratically by means of tris(hydroxymethyl) aminomethane (TRIS) buffers of mildly alkaline pH containing 30% (v/v) acetonitrile as the mobile phases. The samples were injected electrokinetically and the analyses were done at the same separation field strength of 500 V/cm. Microcystins were detected at 238 nm. Although both column types differ not only in monolith quality (inorganic versus organic) but also in the length of the aliphatic moiety (C8 versus C12) similar results were achieved. The on-column preconcentration as the encouraging prospect of electrochromatographic technique was also tested. Consequently 5% of column volume was injected in contrast with 0.5% at standard injection scheme resulting in the six times enrichment of the low concentrated cyanobacterial extract at the top of the separation column. From these preliminary results can be seen that the CEC method is fully applicable for rapid microcystin screening.     

Separation of cefoperazone enantiomers using beta-cyclodextrin as chiral additive by capillary zone electrophoresis

A capillary electrophoresis method was developed to separate the enantiomers of cefoperazone. Different cyclodextrins, including alpha-cyclodextrin (alpha-CD), beta-cyclodextrin (beta-CD), gamma-cyclodextrin (gamma-CD), 2-hydroxypropyl-beta-cyclodextrin (HP-beta-CD), and methyl-beta-cyclodextrin (Me-beta-CD), were tested as chiral additives in the running buffer. The effect of various parameters on enantioseparation such as concentration of NaH(2)PO(4), buffer pH, and CD concentration was also studied. The cefoperazone enantiomers were baseline separated under conditions of 0.04 mmol/L beta-CD, 75 mmol/L NaH(2)PO(4) buffer at pH 4.0. A fused silica capillary (40 cm effective length x 75 microm ID) was used. The applied voltage and capillary temperature were 20 kV and 25 degrees C, respectively. Under these conditions, linear calibration curves were obtained in the 5-500 microg/ml range using UV detection at 280 nm. The limit of detection for both isomers was 0.1 microg/ml. The method was used for the analysis of different pharmaceutical preparations (dose) and biological samples containing cefoperazone.     

Separation of the enantiomers of some racemic nonsteroidal aromatase inhibitors and barbiturates by capillary electrophoresis

High-performance capillary electrophoresis (HPCE) and micellar electrokinetic capillary chromatography (MECC) were applied to the resolution of racemic nonsteroidal antiaromatase drugs and intermediates. Successful results were obtained in both modes using α-cyclodextrin (α-CD), β-cyclodextrin (β-CD), γ-cyclodextrin (γ-CD), or 2,6-di-O-methyl-β-cyclodextrin (DM-β-CD) as chiral selectors. Depending on the structure of the solute, one of the cyclodextrins was generally better suited for resolution of the racemate. The basic solutes were analyzed under HPCE conditions, whereas the nonionizable compounds such as glutethimide (Doriden®) were analyzed in MECC mode. For the azole-type antiaromatase Fadrozole, both HPCE and MECC modes could be used to achieve the separation of the enantiomers. The influence of experimental factors such as pH, the presence of organic modifier, temperature, the micelle concentration, and the concentration of the chiral selector is also discussed on the basis of the results obtained with some chiral barbiturates. The possibility of analyzing the enantiomers directly in plasma samples was also demonstrated. © 1993 Wiley-Liss, Inc.     

An open tubular capillary electrochromatography column with porous inner surface for protein separation

An open tubular capillary electrochromatography (OTCEC) column using sole porogen to form porous inner surface has been developed. The porous layer was coated on the capillary inner wall by in situ polymerization in the presence of porogen. The results show that the columns using 1-propanol as sole porogen are appropriate for protein separation. It has higher separation efficiency than the column with the usual coporogen due to much more micropores and mesopores on the porous surface and a higher specific surface area. In addition, the sensitivity of the prepared OTCEC column was improved greatly compared with the dynamically coated capillary with polyvinylpyrrolidone.     

Separation of the enantiomers of coumarinic anticoagulant drugs by capillary electrophoresis using maltodextrins as chiral modifiers

The separation and quantitation of coumarinic anticoagulant drug enantiomers were achieved by direct chiral capillary electrophoresis using complex maltooligosaccharide mixtures as stereoselective electrolyte modifiers. Chiral separations were characterized by a high selectivity and efficiency, enabling enantiomeric excess determinations. In addition, preliminary results indicate the applicability of the method for the determination of individual enantiomers in biological samples. So the method can be used to perform stereoselective pharmacokinetic studies. © 1994 Wiley-Liss, Inc.     

Chiral separation-based ligand exchange by open-tubular capillary electrochromatography

Chiral ligand-exchange enantioseparation of aliphatic and aromatic amino acids was successfully performed using a new open-tubular zwitterionic column with tentacle-type polymer stationary phase. The polymeric stationary phase was prepared using 3-chloro-2-hydroxypropyl methacrylate (HPMA-Cl), a new reactive monomer. The preparation procedure of the open-tubular column included silanization, in situ graft polymerization with HPMA-Cl, and l-histidine (l-His) modification. l-His was used as a chiral ligand-exchange selector and copper(II) as a central ion. Successful enantioseparation of six pairs of amino acid enantiomers was achieved with a buffer of 5 mM CuSO₄, 20 mM (NH₄)₂SO₄ at pH 3.0.     

Separation of carvedilol enantiomers in very small volumes of human plasma by capillary electrophoresis with laser-induced fluorescence

A sensitive capillary electrophoretic method for the determination of carvedilol enantiomers in 100 μl of human plasma has been developed and validated. Carvedilol and the internal standard carazolol are isolated from plasma samples by liquid–liquid extraction using diethylether. A sensitive and selective detection is provided by helium–cadmium laser-induced fluorescence. The total analysis time is 17.5 min, about 30 min are needed for the sample preparation. The linearity of the assay ranges from 1.56 to 50 ng/ml per carvedilol enantiomer. The limits of quantification (LOQ) for the carvedilol enantiomers in 100 μl of human plasma are 1.56 ng/ml. The inter-day accuracy for R-carvedilol is between 95.8 and 103% (104% at LOQ) and for S-carvedilol between 97.1 and 103% (107% at LOQ); the inter-day precision values are between 3.81 and 8.64% (10.9% at LOQ) and between 5.47 and 7.86% (7.91% at LOQ) for R- and S-carvedilol, respectively. The small sample volume needed is especially advantageous for the application in clinical studies in pediatric patients. As an application of the assay concentration/time profiles of the carvedilol enantiomers in a 5-year-old patient receiving a test dose of 0.09 mg/kg carvedilol are reported.     

Separation of enantiomers of drugs by capillary electrophoresis,part 7: Gamma-cyclodextrin as chiral solvating agent

Following an extended chiral drug screening program by capillary zone electrophoresis (CZE), the enantioseparation of 86 racemic drugs was tested with γ-cyclodextrin as a chiral solvating agent. Unified conditions were applied to all experiments. In total, 18 drug racemates were separated, 13 entries thereof that had not been separated at the lower CSA concentration applied in an earlier stage of the project. A comparison of the data with the results obtained for α- and β-cyclodextrin points to the significance of partial penetration (“side-on binding”) of aryl groups into the cyclodextrin cavity. Chirality 10:548–554, 1998. © 1998 Wiley-Liss, Inc.     

Separation of drug enantiomers by liquid chromatography and capillary electrophoresis, using immobilized proteins as chiral selectors

Proteins display interesting chiral discrimination properties owing to multiple possibilities of intermolecular interactions with chiral compounds. This review deals with proteins which have been used as immobilized chiral selectors for the enantioseparation of drugs in liquid chromatography and capillary electrophoresis. The main procedures allowing the immobilization of proteins onto matrices, such as silica and zirconia particles, membranes and capillaries are first presented. Then the factors affecting the enantioseparation of drugs in liquid chromatography, using various protein-based chiral stationary phases (CSPs), are reviewed and discussed. Last, chiral separations already achieved using immobilized protein selectors in affinity capillary electrochromatography (ACEC) are presented and compared in terms of efficiency, stability and reproducibility.     

Highly efficient protein separations in high-performance capillary electrophoresis,using hydrophilic coatings on polysiloxane-bonded columns

Three methods for preparing hydrophilic coatings on polysiloxane bonded CElect H-type capillary electrophoresis columns have been shown. The polyalkylsiloxane-bonded phase is the first coating layer on the capillary surface, and nonionic surfactant, hydrophilic polymer, or polymer surfactant, adsorbed onto this first layer through hydrophobic interactions, forms the second coating layer. The resultant capillary surfaces are inert, hydrophilic, and suitable for highly efficient protein separations. The effectiveness and applicability of these capillary surface modification methods were tested for the separations of a variety of proteins over a wide range of buffer pH values under different capillary electrophoretic operation modes.     

Separation of ketoconazole enantiomers by chiral subcritical-fluid chromatography

The separation of ketoconazole enantiomers by subcritical-fluid chromatography using an amylose-based column is described. Drastic changes in the resolution have been obtained for the different organic modifiers evaluated, with ethanol providing the best results. Other chromatographic parameters such as temperature, pressure and flow-rate have also been studied. The best results in terms of resolution and analysis time were obtained using 30% ethanol (containing 0.1% triethylamine and 0.1% trifluoroacetic acid), a pressure of 300 bar, a temperature of 35 degrees C and a flow-rate of 3 ml/min. Under these conditions the ketoconazole enantiomers are resolved in a short time (less than 7 min) and with high resolution (4.29).     

Separation of amino acid enantiomers by micelle-enhanced ultrafiltration

A Micelle-enhanced ultrafiltration (MEUF) separation process was investigated that can potentially be used for large-scale enantioseparations. Copper(II)-amino acid derivatives dissolved in nonionic surfactant micelles were used as chiral selectors for the separation of dilute racemic amino acids solutions. For the alpha-amino acids phenylalanine, phenylglycine, O-methyltyrosine, isoleucine, and leucine good separation was obtained using cholesteryl L-glutamate and Cu(II) ions as chiral selector with an operational enantioselectivity (alpha(op)) up to 14.5 for phenylglycine. From a wide set of substrates, including four beta-amino acids, it was concluded that the performance of this system is determined by two factors: the hydrophobicity of the racemic amino acid, which results in a partitioning of the racemic amino acid over micelle and aqueous solution, and the stability of the diastereomeric complex formed upon binding of the amino acid with the chiral selector. The chiral hydrophobic cholesteryl anchor of the chiral selector also plays an active role in the recognition process, since inversion of the chirality of the glutamate does not yield the reciprocal enantioselectivities. However, if the cholesteryl group is replaced by a nonchiral alkyl chain, reciprocal operational enantioselectivities are found with enantiomeric glutamate selectors.     

Phospholipid-protein coatings for chiral capillary electrochromatography

A phospholipid-bovine serum albumin (BSA) coating was developed for chiral capillary electrochromatographic separation of d- and l-tryptophan. Temperature, liposome composition, and liposome-BSA mixing and extrusion were found to have critical effects on the chiral separation of d- and l-tryptophan in terms of resolution, separation efficiency, and migration times. A solution of 0.5mM phosphatidylcholine (PC)-1 mg/ml BSA performed better than a solution of 0.5mM PC/phosphatidylserine (PS) (80:20, mol%)-1 mg/ml BSA as capillary coating; baseline separation of the enantiomers with satisfactory resolution was then achieved. Temperature played a crucial role in the chiral separation, as demonstrated for phospholipid-coated capillaries immobilized with BSA and lysozyme. The d- and l-tryptophans showed a marked difference in separation efficiency on the PC-BSA-coated capillary; the theoretical plate number of l-tryptophan was above 500,000 m(-1), whereas that of d-tryptophan was only about 22,000 m(-1). Immobilized BSA (pI 4.7) showed better chiral separation selectivity for the enantiomers than did immobilized lysozyme (pI 10.5), alpha-chymotrypsin (pI 8.1-8.3), or avidin (pI 10.0-10.5); also resolution was better and analysis time was faster. Hydrophobic interactions played an important role in the BSA-immobilized phospholipid-coated capillaries. The importance of protein net charge and molar mass for its immobilization in phospholipid-coated capillaries is discussed.     

Fibrous stationary phase in capillary electrochromatography

Capillary electrochromatography (CEC) using fibrous cellulose acetate (CA) stationary phase was investigated. The advantage of this fiber-packed column is relatively easy preparation process compared with other conventional CEC columns, such as particle-packed and wall-coated capillaries. CA fibers are manually packed into a capillary with two guide liners and fixed with a frit at the column inlet. The separation characteristics of this column were investigated using n-alkyl p-hydroxybenzoates (parabens) as the sample probe. It has been demonstrated that the use of a short column length and a specially designed tee-connector as the injection device should make the separation performance and efficiency much higher on the fiber-packed columns. Sufficient separation between methyl and n-butylparabens is obtained on the 5-cm-packed column and linear relationships between the injection time and the peak area are observed. Bubble formation is not encountered during the analysis.     

The separation of biomolecules using capillary electrochromatography

The unique properties of capillary electrochromatography such as high performance, high selectivity, minimum consumption of both reagents and samples, and good compatibility with mass spectrometry make this technique an attractive one for the analysis of biomolecules including peptides, proteins, carbohydrates, nucleosides and nucleotides. Irreversible adsorption between the biomolecules and the charged packing surface leads to a lack of reproducibility and serious peak tailing, so various approaches have been taken to overcome this and to improve the technique for future challenges.     

Analysis of acidic compounds using capillary electrochromatography

Capillary electrochromatography, CEC, is a hybrid of CE and HPLC and is rapidly gaining interest as a potential complementary technique. This paper provides an overview of literature concerning the separation of acidic compounds by CEC which fall into three distinct groups. These groups are those performed using capillaries packed with novel or unique stationary phases designed for CEC, and a smaller group where standard HPLC stationary phases packings such as ODS has been used. The third group involves the use of surface coated capillaries. This paper reviews the separation of acidic compounds by CEC and also includes a number of novel applications to illustrate the separation approaches and the analytical performance possible.     

Separation of albendazole sulfoxide enantiomers by chiral supercritical-fluid chromatography

The enantioseparation of albendazole sulfoxide (ABZSO) by chiral supercritical-fluid chromatography (SFC) on two columns, based on the polysaccharide derivatives Chiralpak AD and Chiralcel OD, was studied. The effect of different modifiers, methanol, ethanol, 2-propanol, and acetonitrile, was examined. The results showed that ABZSO can be separated on both columns, using an alcohol-type modifier. Using the Chiralpak AD column, the best results were obtained with 2-propanol and, in the case of the Chiralcel OD, with methanol.     

Enantioseparation by ligand-exchange using particle-loaded monoliths: Capillary-LC versus capillary electrochromatography

Particle-loaded monoliths containing a polymethacrylamide backbone were prepared by suspending a silica-based chiral phase in the mixture of the monomers followed by in-situ polymerization in the capillary. As chiral selector l-4-hydroxyproline chemically bonded to 3 μm silica particles was used following the separation principle of ligand-exchange. Electrolytes containing Cu(II) ions were used. Amino acid enantiomers were separated by capillary-LC and CEC, whereby the latter showed the better resolution properties. For the chiral separation of α-hydroxy acids the EOF was reversed by copolymerizing diallyldimethylammonium chloride instead of vinylsulfonic acid as charge providing agent. Short columns of 6 cm were found to be sufficient in the case of CEC for baseline separations of amino acids with α values up to 5.     

Enantioseparation by ligand-exchange using particle-loaded monoliths: capillary-LC versus capillary electrochromatography

Particle-loaded monoliths containing a polymethacrylamide backbone were prepared by suspending a silica-based chiral phase in the mixture of the monomers followed by in-situ polymerization in the capillary. As chiral selector l-4-hydroxyproline chemically bonded to 3 microm silica particles was used following the separation principle of ligand-exchange. Electrolytes containing Cu(II) ions were used. Amino acid enantiomers were separated by capillary-LC and CEC, whereby the latter showed the better resolution properties. For the chiral separation of alpha-hydroxy acids the EOF was reversed by copolymerizing diallyldimethylammonium chloride instead of vinylsulfonic acid as charge providing agent. Short columns of 6 cm were found to be sufficient in the case of CEC for baseline separations of amino acids with alpha values up to 5.     

Preparation and characterization of a new open‐tubular capillary column for enantioseparation by capillary electrochromatography

In order to use the enantioseparation capability of cationic cyclodextrin and to combine the advantages of capillary electrochromatography (CEC) with open‐tubular (OT) column, in this study, a new OT‐CEC, coated with cationic cyclodextrin (1‐allylimidazolium‐β‐cyclodextrin [AI‐β‐CD]) as chiral stationary phase (CSP), was prepared and applied for enantioseparation. Synthesized AI‐β‐CD was characterized by infrared (IR) spectrometry and mass spectrometry (MS). The preparation conditions for the AI‐β‐CD‐coated column were optimized with the orthogonal experiment design L₉(3⁴). The column prepared was characterized by scanning electron microscopy (SEM) and elemental analysis (EA). The results showed that the thickness of stationary phase in the inner surface of the AI‐β‐CD‐coated columns was about 0.2 to 0.5 μm. The AI‐β‐CD content in stationary phase based on the EA was approximately 2.77 mmol·m^?2. The AI‐β‐CD‐coated columns could separate all 14 chiral compounds (histidine, lysine, arginine, glutamate, aspartic acid, cysteine, serine, valine, isoleucine, phenylalanine, salbutamol, atenolol, ibuprofen, and napropamide) successfully in the study and exhibit excellent reproducibility and stability. We propose that the column, coated with AI‐β‐CD, has a great potential for enantioseparation in OT‐CEC.