Piezoelectric urea biosensor based on immobilization of urease onto nanoporous alumina membranes

The urease was immobilized onto nanoporous alumina membranes prepared by the two-step anodization method, and a novel piezoelectric urea sensing system with separated porous alumina/urease electrode has been developed through measuring the conductivity change of immobilized urease/urea reaction. The process of urease immobilization was optimized and the performance of the developed urea biosensor was evaluated. The obtained urea biosensor presented high-selectivity monitoring of urea, better reproducibility (S.D. = 0.02, n = 6), shorter response time (30 s), wider linear range (0.5 μM to 3 mM), lower detection limit (0.2 μM) and good long-term storage stability (with about 76% of the enzymatic activity retained after 30 days). The clinical analysis of the urea biosensor confirmed the feasibility of urea detection in urine samples.     

Development of low-cost microfluidic systems for lab-on-a-chip biosensor applications

In this work, we develop low-cost microfluidic systems based on polydimethylsiloxane (PDMS) for lab-on-a-chip applications. PDMS microfluidic structures have been fabricated by micromolding, PDMS casting, and plasma bonding processes. The micromolding technique is used to fabricate PDMS slabs with micro-sized grooves, and the complete microchannel is formed by bonding PDMS slab with glass or PDMS substrate. The molding procedure using SU-8 photoresist patterning on silicon wafer, PDMS microchannel fabrication, and PDMS surface treatment using oxygen plasma and TiO₂ coating, are discussed. The various parameters for oxygen plasma treatment including RF power and treatment time are studied in order to obtain conditions for good bonding with the glass substrate. The best condition for plasma treatment is found to be the low RF power (8 W) with 5 min treatment time. In addition, TiO₂ coating with oxygen plasma treatment has been applied to make PDMS surface more hydrophilic to improve aqueous solution compatilbility. The microfluidic channels for various applications, including sample injection cross channel, micropump channel, T and Y sample mixers, PCR thermocyling chamber and channel, capillary electrophoresis flow channel, and conductimetric systems have been fabricated. Finally, a typical application of the PDMS chip in a flow injection conductimetric system for sodium chloride detection has been demonstrated.     

Comparative study of controlled pore glass, silica gel and poraver for the immobilization of urease to determine urea in a flow injection conductimetric biosensor system

This study compared the responses of three enzyme reactors containing urease immobilized on three types of solid support, controlled pore glass (CPG), silica gel and Poraver. The evaluation of each enzyme reactor column was done in a flow injection conductimetric system. When urea in the sample solution passed though the enzyme reactor, urease catalysed the hydrolysis of urea into charged products. A lab-built conductivity meter was used to measure the increase in conductivity of the solution. The responses of the enzyme reactor column with urease immobilized on CPG and silica gel were similar and were much higher than that of Poraver. Both CPG and silica gel reactor columns gave the same limit of detection, 0.5 mM, and the response was still linear up to 150mM. The analysis time was 4-5 min per sample. The enzyme reactor column with urease immobilized on CPG gave a slightly better sensitivity, 4% higher than the reactor with silica gel. The life time of the immobilized urease on CPG and silica gel were more than 310h operation time (used intermittently over 7 months). Good agreement was obtained when urea concentrations of human serum samples determined by the flow injection conductimetric biosensor system was compared to the conventional methods (Fearon and Berthelot reactions). These were statistically shown using the regression line and Wilcoxon signed rank tests. The results showed that the reactor with urease immobilized on silica gel had the same efficiency as the reactor with urease immobilized on CPG.     

Fluorimetric urease inhibition assay on a multilayer microfluidic chip with immunoaffinity immobilized enzyme reactors

We fabricated a three-layer polydimethylsiloxane (PDMS)-based microfluidic chip for realizing urease inhibition assay with sensitive fluorescence detection. Procedures such as sample prehandling, enzyme reaction, reagent mixing, fluorescence derivatization, and detection can be readily carried out. Urease reactors were prepared by adsorption of rabbit immunoglobulin G (IgG) and immunoreaction with urease-conjugated goat anti-rabbit IgG. Acetohydroxamic acid (AHA) as a competitive inhibitor of urease was tested on the chip. Microfluidically generated gradient concentrations of AHA with substrate (urea) were loaded into urease reactors. After incubation, the produced ammonia was transported out of reactors and then reacted with o-phthalaldehyde (OPA) to generate fluorescent products. Urease inhibition was indicated by a decrease in fluorescence signal detected by microplate reader. The IC₅₀ value of AHA was determined and showed good agreement with that obtained in microplate. The presented device combines several steps of the analytical process with advantages of low reagent consumption, reduced analysis time, and ease of manipulation. This microfluidic approach can be extended to the screening of inhibitory compounds in drug discovery.     

Calorimetric biosensors with integrated microfluidic channels

A microfluidic device capable of measuring real-time enthalpy changes of biochemical reactions and thermal properties of biological fluids is presented in this paper. The device consists of a freestanding microthermopile integrated with a glass microfluidic reaction chamber. The p-type polysilicon/gold microthermopiles fabricated on a 2 μm thick thermally isolated membrane showed a sensitivity of 0.94 V/W and a thermal time constant of less than 100 ms. Although the device is not restricted to enzymatic reactions, in this paper measurements of the heat of reaction from the catalytic action of glucose oxidase, catalase, and urease on glucose, hydrogen peroxide, and urea, respectively, are reported. Reactions were performed in open air using liquid batch testing and in enclosed fluidic reaction chamber by continuous flow experiments. A sensitivity of 53.5 μV/M for glucose, 26.5 μV/M for hydrogen peroxide and 17 μV/M for urea was obtained. Detection limit for glucose in the continuous flow mode is 2 mM (30 pmol). The aim of this work is to demonstrate the potential of the integrated calorimetric microfluidic device for fundamental thermodynamic studies in biochemical reactions. Using arrays of such devices with immobilized enzymes multi-analyte detection can be accomplished and the effects of interferents from competing substrates can be compensated. This paper presents the design, fabrication and initial testing results from such a microthermopile-based thermal biosensor.     

Fabrication of a miniature CMOS-based optical biosensor

This work presents a novel, miniature optical biosensor by immobilizing horseradish peroxidase (HRP) or the HRP/glucose oxidase (GOx) coupled enzyme pair on a CMOS photosensing chip with a detection area of 0.5 mm × 0.5 mm. A highly transparent TEOS/PDMS Ormosil is used to encapsulate and immobilize enzymes on the surface of the photosensor. Interestingly, HRP-catalyzed luminol luminescence can be detected in real time on optical H₂O₂ and glucose biosensors. The minimum reaction volume of the developed optical biosensors is 10 μL. Both optical H₂O₂ and glucose biosensors have an optimal operation temperature and pH of 20–25 °C and pH 8.4, respectively. The linear dynamic range of optical H₂O₂ and glucose biosensors is 0.05–20 mM H₂O₂ and 0.5–20 mM glucose, respectively. The miniature optical glucose biosensor also exhibits good reproducibility with a relative standard deviation of 4.3%. Additionally, ascorbic acid and uric acid, two major interfering substances in the serum during electrochemical analysis, cause only slight interference with the fabricated optical glucose biosensor. In conclusion, the CMOS-photodiode-based optical biosensors proposed herein have many advantages, such as a short detection time, a small sample volume requirement, high reproducibility and wide dynamic range.     

Effects of relative humidity on enzyme activity immobilized in sol–gel-derived silica nanocomposites

Enzyme immobilization has attracted great interest in biotechnology processes. Herein we report the immobilization of urease from Canavalia ensiformis (jack bean) in sol–gel-derived silica nanocomposites. Urease activity, differential scanning calorimetry (DSC), nitrogen and water adsorption isotherms were used to characterize the effect of storage at various relative humidities on enzyme activity immobilized in sol–gel-derived silica nanocomposites. In this study, the nanocomposites consist of tetraethoxysilane, as inorganic silicate precursor, in combination with glycerol or trehalose as organic additives. Entrapped urease was more stable for all the formulations aged with a relative humidity of 80%. However, significant differences (p < 0.05) in enzyme activity recovered at this relative humidity were observed between samples with different formulations, reflecting the effect of additives during the immobilization process. The applications of biocompatible sol–gel-derived matrices can be further extended and utilized in the development of biosensors with immobilized biomolecules that can be used for long time periods by taking into account different factors, among which the storage relative humidity has permitted to greatly improve the stability of the immobilized urease.     

Chemiluminescence determination of moxifloxacin in pharmaceutical and biological samples based on its enhancing effect of the luminol–ferricyanide system using a microfluidic chip

A sensitive determination of a synthetic fluoroquinolone antibacterial agent, moxifloxacin (MOX), by an enhanced chemiluminescence (CL) method using a microfluidic chip is described. The microfluidic chip was fabricated by a soft‐lithographic procedure using polydimethyl siloxane (PDMS). The fabricated PDMS microfluidic chip had three‐inlet microchannels for introducing the sample, chemiluminescent reagent and oxidant, and a 500 µm wide, 250 µm deep and 82 mm long microchannel. An enhanced CL system, luminol–ferricyanide, was adopted to analyze the MOX concentration in a sample solution. CL light was emitted continuously after mixing luminol and ferricyanide in the presence of MOX on the PDMS microfluidic chip. The amount of MOX in the luminol–ferricyanide system influenced the intensity of the CL light. The linear range of MOX concentration was 0.14–55.0 ng/mL with a correlation coefficient of 0.9992. The limit of detection (LOD) and limit of quantification (LOQ) were 0.06 and 0.2 ng/mL respectively. The presented method afforded good reproducibility, with a relative standard deviation (RSD) of 1.05% for 10 ng/mL of MOX, and has been successfully applied for the determination of MOX in pharmaceutical and biological samples. Copyright © 2013 John Wiley & Sons, Ltd.     

Urease immobilized on an aminated polysulphone membrane – inhibition by boric acid

An enzymatic membrane for application in the processes of decomposition and removal of urea from aqueous solutions was prepared: jack bean urease was immobilized on an aminated polysulphone membrane by adsorption. The inhibition of the system by boric acid was studied using procedures based on the MICHAELIS-MENTEN integrated equation (non-linear regression, and the linear transformations of WALKER and SCHMIDT, JENNINGS and NIEMANN, and BOOMAN and NIEMANN). The reaction was carried out in a 100 mM phosphate buffer of pH 7.0, containing 2 mM EDTA, obtained by neutralization of orthophosphoric acid with NaOH, at an initial urea concentration of 10 mM, and a temperature of 25 °C. The reaction was initiated by the addition of the enzyme to the urea solution, and was monitored by removing samples of the reaction mixture for NH₃ determinations by the phenol-hypochlorite method until the urea was exhausted. The results were compared with those obtained earlier under the same reaction conditions for free urease and urease covalently immobilized on chitosan. The inhibition was found to be competitive, similar to that of the free enzyme and urease immobilized on chitosan, with inhibition constants K_i equal to 0.36, 0.19 and 0.60 mM. The results show that adsorption of the enzyme on a polysulphone membrane changed the enzyme to a lesser degree than covalent immobilization of the enzyme on a chitosan membrane.     

Glucose biosensor based on nano-SiO2 and "unprotected" Pt nanoclusters

The “unprotected” Pt nanoclusters (average size 2 nm) mixed with the nanoscale SiO₂ particles (average size 13 nm) were used as a glucose oxidase immobilization carrier to fabricate the amperometric glucose biosensor. The bioactivity of glucose oxidase (GOx) immobilized on the composite was maintained and the as-prepared biosensor demonstrated high sensitivity (3.85 μA mM⁻¹) and good stability in glucose solution. The Pt–SiO₂ biosensor showed a detection limit of 1.5 μM with a linear range from 0.27 to 4.08 mM. In addition, the biosensor can be operated under wide pH range (pH 4.9–7.5) without great changes in its sensitivity. Cyclic voltammetry measurements showed a mixed controlled electrode reaction.     

Physico-Chemical Characterization of Watermelon Urease upon Immobilization in Alginate Beads

Watermelon (Citrullus vulgaris) urease was immobilized in 3.5% alginate leading to 72% immobilization. There was no leaching of the enzyme over a period of 15 days at 4°C. It continued to hydrolyse urea at a faster rate upto 90 min of incubation. The immobilized urease exhibited a shift of apparent pH optimum by one unit towards acidic side (from pH 8.0 to 7.0). The K_m was found to be 13.3 mM; 1.17 times higher than the soluble enzyme (11.4 mM). The beads were fairly stable upto 50°C and exhibited activity even at ?10°C. The enzyme was significantly activated by ME and it exhibited two peaks of activation; one at lower concentration and another at higher concentration. Time-dependent ureolysis in presence of ME progressed at a much elevated rate. Unlike soluble enzyme, which was inhibited at 200 mM urea, the immobilized enzyme was inhibited at 600 mM of urea and above, and about 47% activity was retained at 2000 mM urea. Moreover, the inhibition caused by high urea concentration was partially abolished by ME. The significance of the observations is discussed.     

Properties of urease immobilized on the functional organic silica surface

The paper deals with kinetics of the urea hydrolysis by microbial-origin urease dissolved and immobilized on the organic silica surface. It is shown that hydrolysis kinetics for soluble urease is described by the Michaelis-Menten equation until the concentration of urea reaches 1 M. Two fractions differing in the Michaelis constant are revealed for silochrome immobilized urease. The rate of urea hydrolysis by native and immobilized urease was studied depending on the pH value in presence of the substrate in the 1 M and 5 mM concentration. The hydrolysis rate of 1 M urea in the buffer-free solution by silochrome-immobilized urease is practically independent of pH within 4.5-6.5. Application of a 2.5 mM phosphate-citrate buffer as a solvent causes an increase in the hydrolysis rate within this pH range. For a soluble urease the 1 M urea hydrolysis rate dependence on pH is ordinary at pH 5.8-6.0. If the substrate concentration is 5 mM, the pH-dependences for the rate of the urea hydrolysis by silochrome- and aerosil-immobilized urease are close and at pH above 6.0 coincide with those for a soluble enzyme. The found differences in the properties of soluble and immobilized ureases are explained by the substrate and reaction products diffusion.     

A preliminary study of a biosensor based on flow injection of the recognition element

A biosensor based on flow injection of the recognition element has been developed. As a model a pH-transducer was used, and urease was chosen as the recognition element. The pH-transducer was immersed in an internal flow-through chamber which was in contact with the sample solution via a semi-permeable membrane. The recognition element, urease, was injected into the buffer solution passing through the biosensor. The enzyme catalysed the hydrolysis of urea and the concomitant increase in pH was recorded. The biosensor response time was about three minutes at a constant flow rate of 0·05 ml/min. The linear range of the calibration curve of the biosensor was 0–5 mM. The observed detection limit was approximately 0.1 mM. The sample throughput was 6–12 per hour. The pH-response of the biosensor, for a sample solution containing urea (3·26 mM), showed a reproducibility (r.s.d) of 28% (n = 5) and a repeatability (r.s.d.) of 8% (n = 5). Operation at elevated temperatures (up to 50°C) was demonstrated. The presence of glucose (28 mM), acetone (6·7 mM), citric acid (0·2 mM) or sodium acetate (0·6 mM) in the sample solution did not interfere with the sensor response. A lowering of the biosensor response which was observed in the presence of copper ions (due to urease inhibition) could be completely eliminated by adding EDTA to the urease solution. Thus, this work demonstrates a new type of biosensors, based on SIRE-technology (Sensors with Injectable Recognition Elements), which show high accuracy and stability, quick response and high sample throughput. These features suggest the suitability of the system for automation. Such sensors should readily be combined with other enzymes or enzyme systems. The enzyme (urease) cost per analysis (injection) for the biosensor was estimated to be approximately US$0·02. This could be substantially reduced by further optimisation and miniaturisation.     

The region ion sensitive field effect transistor, a novel bioelectronic nanosensor

A novel type of bioelectronic region ion sensitive field effect transistor (RISFET) nanosensor was constructed and demonstrated on two different sensor chips that could measure glucose with good linearity in the range of 0–0.6 mM and 0–0.3 mM with a limit of detection of 0.1 and 0.04 mM, respectively. The sensor is based on the principle of focusing charged reaction products with an electrical field in a region between the sensing electrodes. For glucose measurements, negatively charged gluconate ions were gathered between the sensing electrodes. The signal current response was measured using a low-noise pico ammeter (pA). Two different sizes of the RISFET sensor chips were constructed using conventional electron beam lithography. The measurements are done in partial volumes mainly restricted by the working distance between the sensing electrodes (790 and 2500 nm, respectively) and the influence of electrical fields that are concentrating the ions. The sensitivity was 28 pA/mM (2500 nm) and 830 pA/mM (790 nm), respectively. That is an increase in field strength by five times between the sensing electrodes increased the sensitivity by 30 times. The volumes expressed in this way are in low or sub femtoliter range. Preliminary studies revealed that with suitable modification and control of parameters such as the electric control signals and the chip electrode dimensions this sensor could also be used as a nanobiosensor by applying single enzyme molecule trapping. Hypotheses are given for impedance factors of the RISFET conducting channel.     

Immobilization of urease on nanostructured polymer membrane and preparation of urea amperometric biosensor

A new matrix for enzyme immobilization of urease was obtained by incorporating rhodium nanoparticles (5% on activated charcoal) and chemical bonding of chitosan with different concentration (0.15%; 0.3%; 0.5%; 1.0%; 1.5%) in previously chemically modified AN copolymer membrane. The basic characteristics of the chitosan modified membranes were investigated. The SEM analyses were shown essential morphology change in the different modified membranes. Both the amount of bound protein and relative activity of immobilized enzyme were measured. A higher activity (about 77.44%) was measured for urease bound to AN copolymer membrane coated with 1.0% chitosan and containing rhodium nanoparticles. The basic characteristics (pH(opt), T(opt), thermal, storage and operation stability) of immobilized enzyme on this optimized modified membrane were also determined. The prepared enzyme membrane was used for the construction of amperometric biosensor for urea detection. Its basic amperometric characteristics were investigated. A calibration plot was obtained for urea concentration ranging from 1.6 to 23 mM. A linear interval was detected along the calibration curve from 1.6 to 8.2mM. The sensitivity of the constructed biosensor was calculated to be 3.1927 μAmM(-1)cm(-2). The correlation coefficient for this concentration range was 0.998. The detection limit with regard to urea was calculated to be 0.5mM at a signal-to-noise ratio of 3. The biosensor was employed for 10 days while the maximum response to urea retained 86.8%.     

Biocatalytic properties of native and immobilized subtilisin 72 in aqueous-organic and low water media

Subtilisin 72 was immobilized on cryogel of poly(vinyl alcohol), the macroporous carrier prepared by the freeze-thaw-treatment of concentrated aqueous solution of the polymer. The obtained biocatalyst was active and stable in aqueous, aqueous-organic, as well as in low water media. The stability of immobilized biocatalyst was substantially higher than that of native enzyme in all mixtures especially in aqueous buffer containing 5–8 M Urea and in acetonitrile/60–90%DMF mixtures. The ability of native and immobilized subtilisin to catalyze peptide bond formation between Z-Ala-Ala-Leu-OMe and Phe-pNA was studied in non-aqueous media. Considerable enzyme stabilization in acetonitrile/90%DMF mixture, induced by the immobilization, resulted in higher product yield (57%) than in case of native subtilisin suspension (32%). Detailed study of synthesis reaction revealed that notable increase in product yield could be reached using increase in both substrate concentrations up to 200 mM.     

Immobilization of catalase into chemically crosslinked chitosan beads

Bovine liver catalase was immobilized into chitosan beads prepared in crosslinking solution. Various characteristics of immobilized catalase such as the pH–activity curve, the temperature–activity curve, thermal stability, operational stability, and storage stability were evaluated. Among them the pH optimum and temperature optimum of free and immobilized catalase were found to be pH 7.0 and 35 °C. The K_m value of immobilized catalase (77.5 mM) was higher than that of free enzyme (35 mM). Immobilization decreased in V_max value from 32,000 to 122 μmol (min mg protein)⁻¹. It was observed that operational, thermal and storage stabilities of the enzyme were increased with immobilization.     

Immobilization of trypsin on poly(urea-formaldehyde)-coated fiberglass cores in microchip for highly efficient proteolysis

Trypsin was covalently immobilized on poly(urea‐formaldehyde)‐coated fiberglass cores based on the condensation reaction between poly(urea‐formaldehyde) and trypsin for efficient microfluidic proteolysis in this work. Prior to use, a piece of the trypsin‐immobilized fiber was inserted into the main channel of a microchip under a magnifier to form a core‐changeable bioreactor. Because trypsin was not permanently immobilized on the channel wall, the novel bioreactor was regenerable. Two standard proteins, hemoglobin (HEM) and lysozyme (LYS), were digested by the unique bioreactor to demonstrate its feasibility and performance. The interaction time between the flowing proteins and the immobilized trypsin was evaluated to be less than 10 s. The peptides in the digests were identified by MALDI‐TOF MS to obtain PMF. The results indicated that digestion performance of the microfluidic bioreactor was better than that of 12‐h in‐solution digestion.     

Resolution of 1,3-dioxolane derivatives using the lipase from an Acinetobacter junii SY-01

Acinetobacter junii SY-01 producing a lipase enantioselectively hydrolyzing 1,3-dioxolane derivatives was isolated from water sludge sample and the effect of solvent, acyl donor, vinyl acetate concentration, substrate concentration, operating temperature and immobilization on activity and enantioselectivity was studied for the resolution of 1,3-dioxolane derivatives through transesterification reaction using a lipase from the isolated strain. Best selectivity was obtained at lower substrate concentration (3–5 mM), higher vinyl acetate concentration (500–1000 mM) and lower temperature (30–40 °C) in the reaction mixture. Lipase immobilized onto Accurel MP-1000 (micro-porous polypropylene) gave the best results and the reactivity was about 29-fold higher than the free enzyme without the decrease of enantioselectivity. Resolution of 1,3-dioxolane derivatives was carried out in flask scale containing 100 ml solvents using the lipase immobilized onto Accurel MP-1000. In this reaction, the yield and enantiomeric excess of the remaining (2R, 4S)-alcohol were 31.2% and 98.2%, respectively. This result suggests that it can be used as an alternative method, compared to the present synthetic method, for the production of optically pure (2R, 4S)-itraconazole.     

Effects of anti-oxidant additives on microscopic and oxidative parameters of Angora goat semen following the freeze–thawing process

The anti-oxidant system of reduced glutathione (GSH), glutathione peroxidase (GSH-PX), catalase (CAT), and superoxide dismutase (SOD) has been described as a defense functioning mechanism against lipid peroxidation (LPO) in semen, and is important in maintaining sperm motility and viability. This anti-oxidant capacity of sperm cells may be insufficient in preventing LPO during the freeze–thawing process. The aim of this study was thus to determine the influence of varying doses of anti-oxidant additives on standard semen parameters, lipid peroxidation and anti-oxidant activities after the freeze–thawing of goat semen. Ejaculate samples (artificial vagina) obtained from 4 mature Angora goats were evaluated and pooled at 37 °C. The semen samples diluted with a Tris-based extender, containing taurine (25, 50, 75 mM), trehalose (25, 50, 75 mM), and cysteine (5, 10, 15 mM), and an extender containing no anti-oxidant additives (control) were again evaluated. Diluted semen was cooled down to 5 °C and frozen in 0.25 ml French straws, prior to being stored in liquid nitrogen. Frozen straws were thawed in a water bath (37 °C) for 30 s for microscopic sperm evaluation. Upon evaluation of parameters for semen quality, the use of a Tris-based extender supplemented with anti-oxidant additives was found to cause no significant improvement in sperm mortality, when compared to the controls. Increasing doses of taurine and trehalose decreased (P < 0.05) the sperm motility following the freeze–thawing of the goat semen. In biochemical assays, the application of taurine (75 mM) produced the lowest level of malondialdehyde (MDA) (4.46 ± 0.31 nmol/ml), compared to the controls (P < 0.001). Lower GSH levels were higher in the groups in which cysteine was included at 10 and 15 mM (3.27 ± 0.11 and 3.45 ± 0.28 nmol/ml) – compared to the group which received 5 mM cysteine, as well as the controls (2.27 ± 0.08 and 2.50 ± 0.08 nmol/ml respectively, P < 0.001). Compared to the controls, taurine at a concentration of 25 and 75 mM, and increasing doses (50 and 75 mM) of trehalose, significantly increased the GSH-PX activity (P < 0.01). The maintenance of CAT activity was demonstrated to be higher with the addition of 10 and 15 mM cysteine, compared to the other groups (P < 0.001). Vitamin A (VitA) levels were significantly higher, compared to the controls (267.34 ± 9.68 mg/dl and 267.34 ± 9.68 mg/dl, respectively), when 25 mM taurine (329.61 ± 6.35 mg/dl) and 10 mM (318.64 ± 6.34 mg/dl) cysteine was added to the extender (P < 0.001). The results of this study provide a new approach to the cryopreservation of Angora goat semen and could contribute to the improvement of this technology in the goat industry.