Improving the lactic acid production of Actinobacillus succinogenes by using a novel fermentation and separation integration system

This work describes the development of a novel integrated system for lactic acid production by Actinobacillus succinogenes. Fermentation and separation were integrated with the use of a microfiltration (MF) membrane, and lactic acid was recovered by resin adsorption following MF. The fermentation broth containing residual sugar and nutrients was then recycled back into the fermenter after lactic acid adsorption. This novel approach overcame the problem of product inhibition and extended the cell growth period from 41 h to 120 h. Production of lactic acid was improved by 23% to 183.4 g L⁻¹. The overall yield and productivity for glucose were 0.97 g g⁻¹ and 1.53 g L⁻¹ h⁻¹, respectively. These experimental results indicate that the integrated system could benefit continuous production of lactic acid at high levels.     

d- and l-lactic acid production from fresh sweet potato through simultaneous saccharification and fermentation

The aim of this study was to develop a bioprocess for l- and d-lactic acid production from raw sweet potato through simultaneous saccharification and fermentation by Lactobacillus paracasei and Lactobacillus coryniformis, respectively. The effects of enzyme and nitrogen source concentrations as well as of the ratio of raw material to medium were investigated. At dried material concentrations of 136.36–219.51 g L⁻¹, yields of 90.13–91.17% (w/w) and productivities of 3.41–3.83 g L⁻¹ h⁻¹ were obtained with lactic acid concentrations as high as 198.32 g L⁻¹ for l-lactic acid production. In addition, d-lactic acid was produced with yields of 90.11–84.92% (w/w) and productivities of 2.55–3.11 g L⁻¹ h⁻¹ with a maximum concentration of 186.40 g L⁻¹ at the same concentrations of dried material. The simple and efficient process described in this study will benefit the tuber and root-based lactic acid industries without requiring alterations in plant equipment.     

Influence of specific growth rate over the secretory expression of recombinant potato carboxypeptidase inhibitor in fed-batch cultures of Escherichia coli

A high cell density cultivation protocol was developed for the secretory production of potato carboxypeptidase inhibitor (PCI) in Escherichia coli. The strain BW25113 (pIMAM3) was cultured in fed-batch mode employing minimal media and an exponential feed profile where the specific growth rate was fixed by limitation of the fed carbon source (glycerol). Plasmid loss rates were found to be proportional to the specific growth rate. Distribution of PCI along the cell compartments and the culture media was also dependent on the fixed growth rate. When specific growth rate was kept at μ = 0.10 h⁻¹, 1.4 g PCI L⁻¹ were obtained when adding the product present in periplasmic extracts and supernatant fractions, with a 50% of the total expressed protein recovered from the extracellular medium. This constituted a 1.2-fold increase compared to growth at μ = 0.15 h⁻¹, and 2.0-fold compared to μ = 0.25 h⁻¹. Last, a cell permeabilization treatment with Triton X-100 and glycine was employed to direct most of the product to the culture media, achieving over 81% of extracellular PCI. Overall, our results point out that production yields of secretory proteins in fed-batch cultures of E. coli can be improved by means of process variables, with applications to the production of small disulfide-bridged proteins. Overall, our results point out that control of the specific growth rate is a successful strategy to improve the production yields of secretory expression in fed-batch cultures of E. coli, with applications to the production of small disulfide-bridged proteins.     

Metabolic engineering of Corynebacterium glutamicum for the production of itaconate

The capability of Corynebacterium glutamicum for glucose-based synthesis of itaconate was explored, which can serve as building block for production of polymers, chemicals, and fuels. C. glutamicum was highly tolerant to itaconate and did not metabolize it. Expression of the Aspergillus terreus CAD1 gene encoding cis-aconitate decarboxylase (CAD) in strain ATCC13032 led to the production of 1.4 mM itaconate in the stationary growth phase. Fusion of CAD with the Escherichia coli maltose-binding protein increased its activity and the itaconate titer more than two-fold. Nitrogen-limited growth conditions boosted CAD activity and itaconate titer about 10-fold to values of 1440 mU mg⁻¹ and 30 mM. Reduction of isocitrate dehydrogenase activity via exchange of the ATG start codon to GTG or TTG resulted in maximal itaconate titers of 60 mM (7.8 g l⁻¹), a molar yield of 0.4 mol mol⁻¹, and a volumetric productivity of 2.1 mmol l⁻¹ h⁻¹.     

The effects of NH4+ and NO3− on growth,resource allocation and nitrogen uptake kinetics of Phragmites australis and Glyceria maxima

The effects of NH₄⁺ or NO₃⁻ on growth, resource allocation and nitrogen (N) uptake kinetics of two common helophytes Phragmites australis (Cav.) Trin. ex Steudel and Glyceria maxima (Hartm.) Holmb. were studied in semi steady-state hydroponic cultures. At a steady-state nitrogen availability of 34 μM the growth rate of Phragmites was not affected by the N form (mean RGR = 35.4 mg g⁻¹ d⁻¹), whereas the growth rate of Glyceria was 16% higher in NH₄⁺-N cultures than in NO₃⁻-N cultures (mean = 66.7 and 57.4 mg g⁻¹ d⁻¹ of NH₄⁺ and NO₃⁻ treated plants, respectively). Phragmites and Glyceria had higher S/R ratio in NH₄⁺ cultures than in NO₃⁻ cultures, 123.5 and 129.7%, respectively.Species differed in the nitrogen utilisation. In Glyceria, the relative tissue N content was higher than in Phragmites and was increased in NH₄⁺ treated plants by 16%. The tissue NH₄⁺ concentration (mean = 1.6 μmol g fresh wt⁻¹) was not affected by N treatment, whereas NO₃⁻ contents were higher in NO₃⁻ (mean = 1.5 μmol g fresh wt⁻¹) than in NH₄⁺ (mean = 0.4 μmol g fresh wt⁻¹) treated plants. In Phragmites, NH₄⁺ (mean = 1.6 μmol g fresh wt⁻¹) and NO₃⁻ (mean = 0.2 μmol g fresh wt⁻¹) contents were not affected by the N regime. Species did not differ in NH₄⁺ (mean = 56.5 μmol g⁻¹ root dry wt h⁻¹) and NO₃⁻ (mean = 34.5 μmol g⁻¹ root dry wt h⁻¹) maximum uptake rates (V_max), and V_max for NH₄⁺ uptake was not affected by N treatment. The uptake rate of NO₃⁻ was low in NH₄⁺ treated plants, and an induction phase for NO₃⁻ was observed in NH₄⁺ treated Phragmites but not in Glyceria. Phragmites had low K_m (mean = 4.5 μM) and high affinity (10.3 l g⁻¹ root dry wt h⁻¹) for both ions compared to Glyceria (K_m = 6.3 μM, affinity = 8.0 l g⁻¹ root dry wt h⁻¹). The results showed different plasticity of Phragmites and Glyceria toward N source. The positive response to NH₄⁺-N source may participates in the observed success of Glyceria at NH₄⁺ rich sites, although other factors have to be considered. Higher plasticity of Phragmites toward low nutrient availability may favour this species at oligotrophic sites.     

Investigation on the properties and kinetics of glucose-fed aerobic granular sludge

Aerobic granulation is a process in which suspended biomass aggregate and form discrete well-defined granules in aerobic systems. To investigate the properties and kinetics of aerobic granular sludge, aerobic granules were cultivated with glucose synthetic wastewater in a series of sequencing batch reactors (SBR). The spherical shaped granules were observed on 8th day with the mean diameter of 0.1 mm. With the organic loading rate (OLR) being increased to 4.0 g COD L⁻¹ d⁻¹, aerobic granules grew matured with spherical shape. The size of granules ranged from 1.2 to 1.8 mm, and the corresponding settling velocity of individual granule was 24.2–36.4 m h⁻¹. The oxygen utilization rate (OUR) of mature granules was 41.90 g O₂ kg MLSS⁻¹ h⁻¹, which was two times higher than that of activated sludge (18.32 g O₂ kg MLSS⁻¹ h⁻¹). The experimental data indicated that the substrate utilization and biomass growth kinetics generally followed Monod's kinetics model. The corresponding kinetic coefficients of k (maximum specific substrate utilization rate), K_s (half velocity coefficient), Y (growth yield coefficient) and K_d (decay coefficient) were determined as follows, k_c = 23.65 d⁻¹, K_c = 3367.05 mg L⁻¹, K_N = 0.038 d⁻¹, K_N = 29.65 mg L⁻¹, Y = 0.1927–0.2022 mg MMLS (mg COD)⁻¹ and K_d = 0.00845–0.0135 d⁻¹, respectively. Those properties of aerobic granules made aerobic granules system had a short setup period, high substrate utilization rate and low sludge production.     

Immobilization of Lactobacillus rhamnosus in polyvinyl alcohol/calcium alginate matrix for production of lactic acid

Immobilization of Lactobacillus rhamnosus ATCC7469 in poly(vinyl alcohol)/calcium alginate (PVA/Ca-alginate) matrix using “freezing–thawing” technique for application in lactic acid (LA) fermentation was studied in this paper. PVA/Ca-alginate beads were made from sterile and non-sterile PVA and sodium alginate solutions. According to mechanical properties, the PVA/Ca-alginate beads expressed a strong elastic character. Obtained PVA/Ca-alginate beads were further applied in batch and repeated batch LA fermentations. Regarding cell viability, L. rhamnosus cells survived well rather sharp immobilization procedure and significant cell proliferation was observed in further fermentation studies achieving high cell viability (up to 10.7 log CFU g⁻¹) in sterile beads. In batch LA fermentation, the immobilized biocatalyst was superior to free cell fermentation system (by 37.1%), while the highest LA yield and volumetric productivity of 97.6% and 0.8 g L⁻¹ h⁻¹, respectively, were attained in repeated batch fermentation. During seven consecutive batch fermentations, the biocatalyst showed high mechanical and operational stability reaching an overall productivity of 0.78 g L⁻¹ h⁻¹. This study suggested that the “freezing–thawing” technique can be successfully used for immobilization of L. rhamnosus in PVA/Ca-alginate matrix without loss of either viability or LA fermentation capability.

     

Effect of oxygen supply on biomass and helvolic acid production in submerged fermentation of Cordyceps taii

The entomogenous fungus Cordyceps taii, a traditional Chinese medicinal mushroom, exhibits potent important pharmacological effects and it has great potential for health foods and medicine. In this work, the effects of oxygen supply on production of biomass and bioactive helvolic acid were studied in shake-flask fermentation of C. taii mycelia. The value of initial volumetric oxygen transfer coefficient (K_La) within 10.1–33.8 h⁻¹ affected the cell growth, helvolic acid production and expression levels of biosynthetic genes. The highest cell concentration of 17.2 g/L was obtained at 14.3 h⁻¹ of initial K_La. The highest helvolic acid production was 9.6 mg/L at 10.1 h⁻¹ of initial K_La. The expression levels of three genes encoding hydroxymethylglutaryl-CoA synthase, hydroxymethylglutaryl-CoA reductase and squalene synthase were down-regulated on day 2 and day 8 but up-regulated on day 14 at an initial K_La value of 10.1 h⁻¹ vs. 33.8 h⁻¹, which well corresponded to the helvolic acid biosynthesis in those conditions. The information obtained would be helpful for improving the biomass and helvolic acid production in large-scale fermentation of C. taii.     

Characterization and overproduction of a thermo-alkaline pectate lyase from alkaliphilic Bacillus licheniformis with potential in ramie degumming

A thermo-alkaline pectate lyase (BliPelA) gene from an alkaliphilic Bacillus licheniformis strain was cloned and overexpressed in Escherichia coli. Mature BliPelA exhibited maximum activity at pH 11 and 70 °C, and demonstrated cleavage capability on a broad range of substrates such as polygalacturonic acid, pectins, and methylated pectins. The highest specific activity, of 320 U mg⁻¹, was towards polygalacturonic acid. Significant ramie (Boehmeria nivea) fiber weight loss (21.5%) was obtained following enzyme treatment and combined enzyme-chemical treatment (29.3%), indicating a high ramie degumming efficiency of BliPelA. The total activity of recombinant BliPelA reached 1450.1 U ml⁻¹ with a productivity of 48.3 U ml⁻¹ h⁻¹ under high-cell-density cultivation with a glycerol exponential feeding strategy for 30 h in 1-l fed-batch fermenter, and 1380.1 U ml⁻¹ with a productivity of 57.5 U ml⁻¹ h⁻¹ after 24 h under constant glucose feeding in a 20-l fermenter using E. coli as the host. The enzyme yields reached 4.5 and 4.3 g l⁻¹ in 1-l and 20-l fed-batch fermenters, respectively, which are higher than those of most reported alkaline Pels. Based on these promising properties and high-level production, BliPelA shows great potential for application in ramie degumming in textile industry.     

Optimized endodextranase-epoxy CIM® disk reactor for the continuous production of molecular weight-controlled prebiotic isomalto-oligosaccharides

An epoxy-activated monolithic Convective Interaction Media (CIM^®) disk was used for the immobilization of endodextranase D8144 from Penicillium sp. (EC 3.2.1.11) in order to produce on-line isomalto-oligosaccharides (IMOs) from Dextran T40. Enzymatic parameters, molecular weight of IMOs and performance of the IMmobilized Enzymes Reactor (IMER) were investigated. The immobilization yield of enzymes was about 45.3% (w/w), and the real specific activity close to 3.26 U mg⁻¹. The K_m values did not significantly change between free (12.8 g L⁻¹) and immobilized enzymes (14.2 g L⁻¹), due to the absence of diffusional limitation. The IMER system presented more than 80% of its residual activity after 5000 column volumes, highlighting the high stability of the immobilized endodextranases. Response surface methodology was used to enhance the performance of the IMER. Depending on dextran concentrations and flow rates, specific patterns of IMOs distributions were observed during the enzymatic hydrolysis. Finally, prebiotic activity was also investigated on IMOs produced by medium conditions (flow rate 0.3 mL min⁻¹ and dextran concentrations 4% w/w) against Lactobacillus rhamnosus GG (ATCC 53103). Their scores were at least as good as two commercialized fructo-oligosaccharides (FOS), Fibrulose^® F97 and Orafti^® P95.     

High cell density fed-batch fermentation for the production of a microbial lipase

Extracellular lipase of the yeast Candida rugosa was produced via high cell density fed-batch fermentations using palm oil as the sole source of carbon and energy. Feeding strategies consisted of a pH-stat operation, foaming-dependent control and specific growth rate control in different experiments. Compared to foaming-dependent feeding and the pH-stat operation, the specific growth rate control of feeding proved to be the most successful. At the specific growth rate control set at 0.05 h⁻¹, the final lipase activity in the culture broth was the highest at ∼700 U L⁻¹. This was 2.6-fold higher than the final enzyme activity obtained at a specific growth rate control set at 0.15 h⁻¹. The peak enzyme concentration achieved using the best foaming-dependent control of feeding was around 28% of the peak activity attained using the specific growth rate control of feeding at 0.05 h⁻¹. Similarly, the peak enzyme concentration attained using the pH-stat feeding operation was a mere 9% of the peak activity attained by specific growth rate control of feeding at a set-point of 0.05 h⁻¹. Fed-batch fermentations were performed in a 2 L stirred-tank bioreactor (30 °C, pH 7) with the dissolved oxygen level controlled at 30% of air saturation.     

Introduction of a bacterial acetyl-CoA synthesis pathway improves lactic acid production in Saccharomyces cerevisiae

Acid-tolerant Saccharomyces cerevisiae was engineered to produce lactic acid by expressing heterologous lactate dehydrogenase (LDH) genes, while attenuating several key pathway genes, including glycerol-3-phosphate dehydrogenase1 (GPD1) and cytochrome-c oxidoreductase2 (CYB2). In order to increase the yield of lactic acid further, the ethanol production pathway was attenuated by disrupting the pyruvate decarboxylase1 (PDC1) and alcohol dehydrogenase1 (ADH1) genes. Despite an increase in lactic acid yield, severe reduction of the growth rate and glucose consumption rate owing to the absence of ADH1 caused a considerable decrease in the overall productivity. In Δadh1 cells, the levels of acetyl-CoA, a key precursor for biologically applicable components, could be insufficient for normal cell growth. To increase the cellular supply of acetyl-CoA, we introduced bacterial acetylating acetaldehyde dehydrogenase (A-ALD) enzyme (EC 1.2.1.10) genes into the lactic acid-producing S. cerevisiae. Escherichia coli-derived A-ALD genes, mhpF and eutE, were expressed and effectively complemented the attenuated acetaldehyde dehydrogenase (ALD)/acetyl-CoA synthetase (ACS) pathway in the yeast. The engineered strain, possessing a heterologous acetyl-CoA synthetic pathway, showed an increased glucose consumption rate and higher productivity of lactic acid fermentation. The production of lactic acid was reached at 142 g/L with production yield of 0.89 g/g and productivity of 3.55 g L⁻¹ h⁻¹ under fed-batch fermentation in bioreactor. This study demonstrates a novel approach that improves productivity of lactic acid by metabolic engineering of the acetyl-CoA biosynthetic pathway in yeast.     

CO2 fixation for succinic acid production by engineered Escherichia coli co-expressing pyruvate carboxylase and nicotinic acid phosphoribosyltransferase

In wild-type Escherichia coli, 1 mol of CO₂ was fixated in 1 mol of succinic acid generation anaerobically. The key reaction in this sequence, catalyzed by phosphoenolpyruvate carboxylase (PPC), is carboxylation of phosphoenolpyruvate to oxaloacetate. Although inactivation of pyruvate formate-lyase and lactate dehydrogenase is found to enhance the PPC pathway for succinic acid production, it results in excessive pyruvic acid accumulation and limits regeneration of NAD⁺ from NADH formed in glycolysis. In other organisms, oxaloacetate is synthesized by carboxylation of pyruvic acid by pyruvate carboxylase (PYC) during glucose metabolism, and in E. coli, nicotinic acid phosphoribosyltransferase (NAPRTase) is a rate-limiting enzyme of the NAD(H) synthesis system. To achieve the NADH/NAD⁺ ratio decrease as well as carbon flux redistribution, co-expression of NAPRTase and PYC in a pflB, ldhA, and ppc deletion strain resulted in a significant increase in cell mass and succinic acid production under anaerobic conditions. After 72 h, 14.5 g L⁻¹ of glucose was consumed to generate 12.08 g L⁻¹ of succinic acid. Furthermore, under optimized condition of CO₂ supply, the succinic acid productivity and the CO₂ fixation rate reached 223.88 mg L⁻¹ h⁻¹ and 83.48 mg L⁻¹ h⁻¹, respectively.     

Comparative kinetic study between moving bed biofilm reactor-membrane bioreactor and membrane bioreactor systems and their influence on organic matter and nutrients removal

New technologies regarding wastewater treatment have been developed. Among these technologies, the moving bed biofilm reactor combined with membrane bioreactor (MBBR-MBR) is a recent solution alternative to conventional processes. This paper presents the results obtained from three wastewater treatment plants working in parallel. The first wastewater treatment plant consisted of a membrane bioreactor (MBR), the second one was a MBBR-MBR system containing carriers both in anoxic and aerobic zones, and the last one consisted of a MBBR-MBR system which contained carriers only in the aerobic zone. The reactors operated with a hydraulic retention time of 26.47 h. During the study, the difference between the experimental plants was not statistically significant concerning organic matter and nutrients removal. However, different tendencies regarding nutrients removal are shown by the three wastewater treatment plants. In this sense, the performances in terms of nitrogen and phosphorus removal of the MBBR-MBR system which contained carriers only in the aerobic zone (67.34 ± 11.22% and 50.65 ± 11.13%, respectively) were slightly better than those obtained from another experimental plants. As a whole, the pilot plant which consisted of a MBR showed better performance from the point of view of the kinetics of the heterotrophic and autotrophic biomass with values of μ_m,H = 0.00858 h⁻¹, μ_m,A = 0.07646 h⁻¹, K_M = 2.37 mg O₂ L⁻¹ and K_NH = 1.31 mg N L⁻¹.     

2,3-Butanediol production using Klebsiella oxytoca ATCC 8724: Evaluation of biomass derived sugars and fed-batch fermentation process

For this study, 2,3-butanediol (BD) fermentation from pure and biomass-derived sugar were optimized in shake-flask and 5-L bioreactor levels using Klebsiella oxytoca ATCC 8724. The results showed that 70 g/L of single sugar (glucose or xylose) and 90 g/L of mixed-sugar (glucose:xylose = 2:1) were optimum concentrations for efficient 2,3-BD fermentation. At optimum sugar concentrations, 2,3-BD productivities were 1.03, 0.64 and 0.50 gL⁻¹ h⁻¹, and yields were 0.43, 0.36 and 0.35 g/g in glucose, xylose and mixed-sugar medium, respectively. The lack of simultaneous utilization of glucose and xylose led to the lowest productivity in the mixed-sugar medium. Detoxification of biomass hydrolyzates was necessary for efficient 2,3-BD fermentation when sugar concentrations in the medium was 90 g/L or higher, but not with sugar concentrations of 30 g/L or less. A fed-batch fermentation using glucose medium led to an increase 2,3-BD titer to 79.4 g/L and yields 0.47 g/g, while productivity decreased to 0.79 gL⁻¹ h⁻¹. However, the fed-batch process was inefficient using mixed-sugar and biomass hydrolyzates because of poor xylose utilization. These results indicated that appropriate biomass processing technologies must be developed to generate separate glucose and xylose streams to produce high 2,3-BD titer from biomass-derived sugar using a fed-batch process.     

Roles of extracellular lactose hydrolysis in cellulase production by Trichoderma reesei Rut C30 using lactose as inducing substrate

Lactose, an inexpensive, soluble substrate, offers reasonably good induction for cellulase production by Trichoderma reesei. The fungus does not uptake lactose directly. Lactose is hydrolyzed to extracellular glucose and galactose for subsequent ingestion. The roles of this extracellular hydrolysis step were investigated in this study. Batch and continuous cultures were grown on the following substrates: lactose, lactose–glycerol mixtures, glucose, galactose, and glucose–galactose mixtures. Cell growth, substrate consumption, lactose hydrolysis, and lactase and cellulase production were followed and modeled. Cells grew much faster on glucose than on galactose, but with comparable cell yields. Glucose (at >0.3 g/L) repressed the galactose consumption. Cellulase synthesis was growth-independent while lactase synthesis was growth-dependent, except at D < ∼0.065 h⁻¹ where a basal level lactase production was observed. For cellulase production the optimal D was 0.055–0.065 h⁻¹ where the enzyme activity and productivity were both near maxima. The model suggested that lactase synthesis was subject to weak galactose repression. As the galactose concentration increased at high D (>0.1 h⁻¹), lactase synthesis became repressed. The insufficient lactase synthesis limited the lactose hydrolysis rate. Extracellular lactose hydrolysis was concluded to be the rate-limiting step for growth of T. reesei Rut C30 on lactose.     

Seasonal variations in photosynthetic irradiance response curves of macrophytes from a Mediterranean coastal lagoon

The main photosynthesis and respiration parameters (dark respiration rate, light saturated production rate, saturation irradiance, photosynthetic efficiency) were measured on a total of 23 macrophytes of the Thau lagoon (2 Phanerogams, 5 Chlorophyceae, 10 Rhodophyceae and 6 Phaeophyceae). Those measurements were performed in vitro under controlled conditions, close to the natural ones, and at several seasons. Concomitantly, measurements of pigment concentrations, carbon, phosphorous and nitrogen contents in tissues were performed. Seasonal intra-specific variability of photosynthetic parameters was found very high, enlightening an important acclimatation capacity. The highest photosynthetic capacities were found for Chlorophyceae (e.g. Monostroma obscurum thalli at 17 °C, 982 μmol O₂ g⁻¹ dw h⁻¹ and 9.1 μmol O₂ g⁻¹ dw h⁻¹/μmol photons m⁻² s⁻¹, respectively for light saturated net production rate and photosynthetic efficiency) and Phanerogams (e.g. Nanozostera noltii leaves at 25 °C, 583 μmol O₂ g⁻¹ dw h⁻¹ and 2.6 μmol O₂ g⁻¹ dw h⁻¹/μmol photons m⁻² s⁻¹ respectively for light saturated net production rate and photosynthetic efficiency). As expected, species with a high surface/volume ratio were found to be more productive than coarsely branched thalli and thick blades shaped species. Contrary to R_d (ranging 6.7–794 μmol O₂ g⁻¹ dw h⁻¹, respectively for Rytiphlaea tinctoria at 7 °C and for Dasya sessilis at 25 °C) for which a positive relationship with water temperature was found whatever the species studied, the evolution of P/I curves with temperature exhibited different responses amongst the species. The results allowed to show summer nitrogen limitation for some species (Gracilaria bursa-pastoris and Ulva spp.) and to propose temperature preferences based on the photosynthetic parameters for some others (N. noltii, Zostera marina, Chaetomorpha linum).     

Enzymatic transformation of tyrosol by Trametes trogii laccases: Identification of the product and study of its biological activities

Oxidative transformation of tyrosol catalysed by Trametes trogii laccases in aqueous solution was investigated. LC–MS analysis shows that tyrosol was converted to its dimer. The enzymatic reaction was also investigated by ¹H and ¹³C nuclear magnetic resonance, and the product formed was identified as a dimeric tetracyclic ketone. The bactericidal and fungicidal properties of tyrosol dimer were investigated using the NCCLS broth dilution and EN 1276 standard methods. High bactericidal and fungicidal effect of concentrations ranged between 1–0.5 g L⁻¹ and 8–4 g L⁻¹ were obtained. Dimer concentrations of 33 g L⁻¹ and 66 g L⁻¹ allowed reductions in viability higher than 5 log units per mL for Pseudomonas aeruginosa ATCC 15442, Escherichia coli ATCC 10536 and Enterococcus hirae ATCC 10541, Staphylococcus aureus ATCC 9144 respectively, within a contact time of 5 min under dirty conditions. The effect of this product on Tuta absoluta, a harmful pest of tomato in the world, was also evaluated. The results showed high insecticidal activity against this insect at a concentration of 16.5 g L⁻¹. Germinability experiments on Lycopersicum esculetum were conducted in order to evaluate the potential of a laccase treatment in removing tyrosol phytotoxicity. The results showed that tyrosol dimer was nonphytotoxic. This study presents the first comprehensive results of biological characterisation of the product obtained by the action of laccase on tyrosol transformation with T. trogii laccases.     

Effects of geometrical design on hydrodynamic and mass transfer characteristics of a rectangular-column airlift bioreactor

Gas holdup and gas–liquid mass transfer coefficients were measured in a 21-L rectangular-column airlift bioreactor with aspect ratio of 10 and working volumes ranging from 10 to 16 L. The effect of the bottom and top clearances was investigated using water and mineralized CMC solutions and covering a range of effective viscosity from 0.02 to 0.5 Pa s and surface tension from 0.065 to 0.085 N m⁻¹. The gas holdup and mass transfer results were successfully correlated using expressions derived via dimensional analysis. The separator gas holdup was found to be similar to the total gas holdup in the airlift bioreactor. The downcomer gas holdup (ɛ_d) increased two-fold when the bottom clearance (h_b) was increased from 0.014 to 0.094 m while the top clearance (h_t) had no effect. Increasing h_b decreased the mass transfer by 50% compared to 31% when the top clearance (h_t/D_hr) was increased. It was found that the gas–liquid separator diameter ratio (D_hs/D_hc) exerted the maximal influence of over 65% on mass transfer as compared to both clearances.     

Quasi-continuous fermentation in a reverse-flow diafiltration bioreactor

Heterogeneities occur in various bioreactor designs including cell retention devices. Whereas in external devices changing environmental conditions cannot be prevented, cells are retained in their optimal environment in internal devices. Conventional reverse-flow diafiltration utilizes an internal membrane device, but pulsed feeding causes spatial heterogeneities. In this study, the influence of conventional reverse-flow diafiltration on the yeast Hansenula polymorpha is investigated. Alternating 180 s of feeding with 360 s of non-feeding at a dilution rate of 0.2 h⁻¹ results in an oscillating DOT signal with an amplitude of 60%. Thereby, induced short-term oxygen limitations result in the formation of ethanol and a reduced product concentration of 25%. This effect is enforced at increased dilution rate. To overcome this cyclic problem, sequential operation of three membranes is introduced. Thus, quasi-continuous feeding is achieved reducing the oscillation of the DOT signal to an amplitude of 20% and 40% for a dilution rate of 0.2 h⁻¹ and 0.5 h⁻¹, respectively. Fermentation conditions characterized by complete absence of oxygen limitation and without formation of overflow metabolites could be obtained for dilution rates from 0.1 h⁻¹ to 0.5 h⁻¹. Thus, sequential operation of three membranes minimizes oscillations in the DOT signal providing a nearly homogenous culture over time.