Separation and purification of laccases from two different fungi using aqueous two-phase extraction

Selective purification still poses a challenge in the downstream processing of biomolecules such as proteins and especially enzymes. In this study a polyethylene glycol 3000 (PEG 3000)–phosphate aqueous two-phase system at 25 °C and pH 7 was successfully used for laccase purification and separation. Initially, the effect of phase forming components on enzyme activities in homogenous systems was studied. In the course of the extraction experiments tie lines, enzyme source, initial enzyme activities, phase ratio and sodium chloride concentrations were varied and their influence on the activity partitioning was determined. Partitioning results were validated using clear-native-PAGE and isoelectric focusing. Based on these results, the separation of laccases from Trametes versicolor and Pleurotus sapidus was investigated using the principle of superposition. Sodium chloride was used to adjust laccase partitioning in the applied aqueous two-phase system (ATPS). Finally, two modes of operation are proposed depending on the aim of the purification task. One mode with 0.133 g g⁻¹ of PEG3000, 0.063 g g⁻¹ of phosphate and without sodium chloride separates P. sapidus laccases from T. versicolor laccases with clearance factors of 5.23 and 6.45, respectively. The other mode of operation with 0.124 g g⁻¹ of PEG3000, 0.063 g g⁻¹ of phosphate and 0.013 g g⁻¹ of sodium chloride enables a partitioning of both laccases into the bottom phase of the ATPS resulting in a purification factor of 2.74 and 96% activity recovery.     

Detoxification of Indigo carmine using a combined treatment via a novel trimeric thermostable laccase and microbial consortium

For the first time, the investigation of Indigo carmine decolorization was done using an atypical Scytalidium thermophilum laccase. Crude and purified laccases required high temperatures and slight acidic pH to achieve maximum Indigo decolorization. Kinetic parameters (K_m and k_cat) of the homotrimeric laccase toward Indigo carmine were determined and laccase efficacy toward repeated dye decolorization process was studied. For the first time, 5 g l⁻¹ as initial Indigo carmine concentration were efficiently transformed up to 50% within 6 h of incubation using 0.1 U ml⁻¹ of laccase and without presence of any mediators. In this study, we showed that the atypical laccase transformed the indigoid dye structure, confirmed by the color changing from blue to red. This intermediate (red) was a subject to an efficient microbial consortium treatment monitored by measuring the decrease in optical density and the total organic carbon removal efficiencies. Toxicological studies via micro-toxicity test showed that the released enzymatic and adapted consortium degradation products were both non-toxic while the initial product was toxic.     

Bench-scale fermentation of Trichoderma viride on wastewater sludge: Rheology,lytic enzymes and biocontrol activity

Conidiation and lytic enzyme production by Trichoderma viride at different solids concentration of pre-treated municipal wastewater sludge was examined in a 15-L fermenter. The maximum conidia concentration (5.94 × 10⁷ CFU mL⁻¹ at 96 h) was obtained at 30 g L⁻¹ suspended solids. The maximum lytic enzyme activities were achieved around 12–30 h of fermentation. Bioassay against a fungal phytopathogen, Fusarium sp. showed maximum activity in the sample drawn around 96 h of fermentation at 30 g L⁻¹ suspended solids concentration. Entomotoxicity against spruce budworm larvae showed maximum value ≈17290 SBU μL⁻¹ at 30 g L⁻¹ suspended solids concentration at the end of fermentation (96 h). Plant bioassay showed dual action of T. viride, i.e., disease prevention and growth promotion. The rheological analyses of fermentation sludges showed the pseudoplastic behaviour. In order to maintain required dissolved oxygen concentration ≥30%, the agitation and aeration requirements significantly increased at 35 g L⁻¹ compared to 30 and 25 g L⁻¹. The oxygen uptake rate and volumetric oxygen mass transfer coefficient, k_La at 35 g L⁻¹ did not increase in comparison to 30 g L⁻¹ due to rheological complexity of the broth during fermentation. Thus, the successful fermentation operation of the biocontrol fungus T. viride is a rational indication of its potential for mass-scale production for agriculture and forest sector as a biocontrol agent.     

Galactose-limited fed-batch cultivation of Escherichia coli for the production of lacto-N-tetraose

Lacto-N-tetraose (Gal(β1-3)GlcNAc(β1-3)Gal(β1-4)Glc) is one of the most abundant oligosaccharide structures in human milk. We recently described the synthesis of lacto-N-tetraose by a whole-cell biotransformation with recombinant Escherichia coli cells. However, only about 5% of the lactose was converted into lacto-N-tetraose by this approach. The major product obtained was the intermediate lacto-N-triose II (GlcNAc(β1-3)Gal(β1-4)Glc).In order to improve the bioconversion of lactose to lacto-N-tetraose, we have investigated the influence of the carbon source on the formation of lacto-N-tetraose and on the intracellular availability of the glycosyltransferase substrates, UDP-N-acetylglucosamine and UDP-galactose. By growth of the recombinant E. coli cells on D-galactose, the yield of lacto-N-tetraose (810.8 mg L⁻¹ culture) was 3.6-times higher compared to cultivation on D-glucose.Using fed-batch cultivation with galactose as sole energy and carbon source, a large-scale synthesis of lacto-N-tetraose was demonstrated. During the 26 h feeding phase the growth rate (μ = 0.05) was maintained by an exponential galactose feed. In total, 16 g L⁻¹ lactose were fed and resulted in final yields of 12.72 ± 0.21 g L⁻¹ lacto-N-tetraose and 13.70 ± 0.10 g L⁻¹ lacto-N-triose II. In total, 173 g of lacto-N-tetraose were produced with a space-time yield of 0.37 g L⁻¹ h⁻¹.     

Laccase mediator system for activation of agarose gel: Application for immobilization of proteins

Cross-linked Sepharose beads were treated with laccase–TEMPO system for oxidation of the primary alcohol groups on the sugar moieties. Optimal activation conditions using Trametes versicolor laccase were at pH 5 and 22 °C, giving an aldehyde content of 55 μmol g⁻¹ Sepharose with 28 units g⁻¹ of laccase and 12.5 mM TEMPO. The activated Sepharose was used for immobilization of trypsin as model protein. Highest degree of immobilization was obtained at pH 10.5 but the activity yield was only 31% of that loaded on the gel. The yield of gel bound trypsin activity was increased to 76% (corresponding to about 43 U g⁻¹ Sepharose) when the immobilization was performed in the presence of trypsin inhibitor, benzamidine. The immobilization yields were comparable to that obtained on the matrix activated using sodium periodate (containing 72 μmol aldehyde per g Sepharose). Recycling and storage of the immobilized trypsin preparations showed high stability of the enzyme bound to laccase–TEMPO activated gel.     

Poly-β-hydroxybutyrate/ectoine co-production by ectoine-excreting strain Halomonas salina

The ectoine-excreting bacterial strain of Halomonas salina was employed in the co-production of poly-β-hydroxybutyrate (PHB) and ectoine (Ect) during a fermentation process (PHB/Ect co-production). An efficient PHB/Ect co-production process was carried out at low NaCl concentration (30 g L⁻¹). It was established using ¹H Nuclear Magnetic Resonance spectroscopy that H. salina produces PHB. The effects of the NaCl concentration, the initial C/N ratio, the phosphate concentration and mixed carbon sources were investigated with respect to PHB/Ect co-production. The PHB/Ect co-production system comprised growing and non-growing cell phases and was developed with NaCl concentration of 30 g L⁻¹. The optimal conditions for PHB/Ect co-production by the ectoine-excreting strain of H. salina were 30 g L⁻¹ NaCl, with an initial C/N ratio of 15, an initial phosphate concentration of 12 g L⁻¹ and mixed carbon sources of 55 g L⁻¹ glucose and 25 g L⁻¹ monosodium glutamate. Using a PHB/Ect co-production system with growing and non-growing cell phases prevents the inhibition of PHB synthesis by high concentration of NaCl and significantly reduces ectoine degradation. PHB and ectoine concentrations as high as 35.3 g L⁻¹ and 8.6 g L⁻¹, respectively, were achieved. The efficient co-production of PHB and ectoine at a low NaCl concentration has been realised.     

Improving the lactic acid production of Actinobacillus succinogenes by using a novel fermentation and separation integration system

This work describes the development of a novel integrated system for lactic acid production by Actinobacillus succinogenes. Fermentation and separation were integrated with the use of a microfiltration (MF) membrane, and lactic acid was recovered by resin adsorption following MF. The fermentation broth containing residual sugar and nutrients was then recycled back into the fermenter after lactic acid adsorption. This novel approach overcame the problem of product inhibition and extended the cell growth period from 41 h to 120 h. Production of lactic acid was improved by 23% to 183.4 g L⁻¹. The overall yield and productivity for glucose were 0.97 g g⁻¹ and 1.53 g L⁻¹ h⁻¹, respectively. These experimental results indicate that the integrated system could benefit continuous production of lactic acid at high levels.     

d- and l-lactic acid production from fresh sweet potato through simultaneous saccharification and fermentation

The aim of this study was to develop a bioprocess for l- and d-lactic acid production from raw sweet potato through simultaneous saccharification and fermentation by Lactobacillus paracasei and Lactobacillus coryniformis, respectively. The effects of enzyme and nitrogen source concentrations as well as of the ratio of raw material to medium were investigated. At dried material concentrations of 136.36–219.51 g L⁻¹, yields of 90.13–91.17% (w/w) and productivities of 3.41–3.83 g L⁻¹ h⁻¹ were obtained with lactic acid concentrations as high as 198.32 g L⁻¹ for l-lactic acid production. In addition, d-lactic acid was produced with yields of 90.11–84.92% (w/w) and productivities of 2.55–3.11 g L⁻¹ h⁻¹ with a maximum concentration of 186.40 g L⁻¹ at the same concentrations of dried material. The simple and efficient process described in this study will benefit the tuber and root-based lactic acid industries without requiring alterations in plant equipment.     

Continuous succinic acid production by Actinobacillus succinogenes in a biofilm reactor: Steady-state metabolic flux variation

Continuous anaerobic fermentations were performed in a novel external-recycle, biofilm reactor using d-glucose and CO₂ as carbon substrates. Succinic acid (SA) yields were found to be an increasing function of glucose consumption with the succinic acid to acetic acid ratio increasing from 2.4 g g⁻¹ at a glucose consumption of 10 g L⁻¹, to 5.7 g g⁻¹ at a glucose consumption of 50 g L⁻¹. The formic acid to acetic acid ratio decreased from an equimolar value (0.77 g g⁻¹) at a glucose consumption of 10 g L⁻¹ to a value close to zero at 50 g L⁻¹. The highest SA yield on glucose and highest SA titre obtained were 0.91 g g⁻¹ and 48.5 g L⁻¹ respectively. Metabolic flux analysis based on the established C₃ and C₄ metabolic pathways of Actinobacillus succinogenes revealed that the increase in the succinate to acetate ratio could not be attributed to the decrease in formic acid and that an additional source of NADH was present. The fraction of unaccounted NADH increased with glucose consumption, suggesting that additional reducing power is present in the medium or is provided by the activation of an alternative metabolic pathway.     

Volatile fatty acids accumulation and rhamnolipid generation in situ from waste activated sludge fermentation stimulated by external rhamnolipid addition

The solubilization and acidification of waste activated sludge (WAS) were apparently enhanced by external rhamnolipid (RL) addition. The maximum solute carbohydrate concentrations increased linearly from 48 ± 5 mg COD L⁻¹ in the un-pretreated WAS (blank) to 566 ± 19 mg COD L⁻¹, and protein increased from 1050 ± 8 to 3493 ± 16 mg COD L⁻¹ at RL dosage of 0.10 g g⁻¹ TSS. The highest VFAs concentration peaked at 3840 mg COD L⁻¹ at RL dosage of 0.04 g g⁻¹ TSS, which was 4.24-fold higher than the blank test. RL was generated in situ during WAS fermentation when external RL was added. It was detected that RL concentration was increased from initial 880 ± 92 mg L⁻¹ to 1312 ± 7 mg L⁻¹ at the end of 96 h with RL dosage of 0.04 g g⁻¹ TSS, which was increased to 1.49-fold. Meanwhile, methane production was notably reduced to a quite low level of 2.0 mL CH₄ g⁻¹ VSS, showing effective inhibition of methanogens by RL (58.8 mL CH₄ g⁻¹ VSS in the blank). In addition, the activity of hydrolytic enzymes (protease and α-glucosidase) was enhanced accordingly. VFAs accumulation and RL generation in situ demonstrated that the additional RL substantially performed enhanced biological effects for waste activated sludge fermentation.     

Comparison of salinity tolerance of three Atriplex spp. in well-watered and drying soils

Members of the Chenopodiaceae are well adapted to both salt and drought stress and can serve as model species to understand the mechanisms of tolerance in plants. We grew Atriplex hortensis (ATHO), A. canescens (ATCA), and A. lentiformis (ATLE) along a NaCL salinity gradient under non-water-limited conditions and in drying soils in greenhouse experiments. The species differed in photosynthetic carbon fixation pathway, capacity for sodium uptake, and habitat preferences. Under non-water-limited conditions, ATLE (C4) maintained high growth rates up to 30 g L⁻¹ NaCl. ATHO (C3) had lower growth than ATLE at high salinities, while ATCA (C4) grew more slowly than either ATLE or ATHO and showed no net growth above 20 g L⁻¹ NaCl. ATHO and ATLE accumulated twice as much sodium in their shoots as ATCA, but all three species had increasing sodium levels at higher salinities. Potassium, magnesium and calcium levels were relatively constant over the salinity gradient. All three species showed marked accumulation of chloride across the salinity gradient, whereas nitrate, phosphorous and sulfate decreased with salinity. The effect of drought was simulated by growing plants in sealed pots with an initial charge of water plus NaCl, and allowing them to grow to the end point at which they no longer were able to extract water from the soil solution. Drought and salinity were not additive stress factors for Atriplex spp. in this experiment. NaCl increased their ability to extract water from the soil solution compared to fresh water controls. ATLE showed increased shoot dry matter production and increased water use efficiency (WUE) as initial salinity levels increased from 0 to 30 g L⁻¹ NaCl, whereas dry matter production and WUE peaked at 5 g L⁻¹ for ATHO and ATCA. Final soil moisture salinities tolerated by species were 85 g L⁻¹, 55 g L⁻¹ and 160 g L⁻¹ NaCl for ATHO, ATCA and ATLE, respectively. C4 photosynthesis and sodium accumulation in shoots were associated with high drought and salt tolerance.     

Purification and characterization of yellow laccase from Trametes hirsuta MTCC-1171 and its application in synthesis of aromatic aldehydes

A yellow laccase from the culture filtrate of Trametes hirsuta MTCC-1171 has been purified. The purification methods involved concentration of the culture filtrate by ammonium sulphate precipitation and an anion exchange chromatography on diethylaminoethyl cellulose. The sodium dodecyl sulphate polyacrylamide gel electrophoresis (SDS-PAGE) and native polyacrylamide gel electrophoresis gave single protein band indicating that the enzyme preparation was pure. The molecular mass of the enzyme determined from SDS-PAGE analysis was 55.0 kDa. Using 2,6-dimethoxyphenol, 2,2′[azino-bis-(3-ethylbonzthiazoline-6-sulphonic acid) diammonium salt] and 3,5-dimethoxy-4-hydroxybenzaldehyde azine as the substrates, the K_m, k_cat and k_cat/K_m values of the laccase were found to be 420 μM, 13.04 s⁻¹, 3.11 × 10⁴ M⁻¹ s⁻¹, 225 μM, 13.03 s⁻¹, 1.3 × 10⁵ M⁻¹ s⁻¹ and 100 μM, 13.04 s⁻¹, 5.8 × 10⁴ M⁻¹ s⁻¹, respectively. The pH and temperature optima were 4.5 and 60 °C, respectively while pH and temperature stabilities were pH 4.5 and 50 °C. The activation energy for thermal denaturation of the enzyme was 18.6 kJ/mol/K. The purified laccase has yellow colour and does not show absorption band around 610 nm like blue laccases. The purified laccase transforms toluene, 3-nitrotoluene, 4-nitrotoluene, 3-chlorotoluene, 4-chlorotoluene and 3,4-dimethoxytoluene to benzaldehyde, 3-nitrobenzaldehyde, 4-nitrobenzaldehyde, 3-chlorobenzaldehyde, 4-chlorobenzaldehyde and 3,4-dimethoxybenzaldehyde in the absence of mediator molecules in high yields.     

Production of specific-molecular-weight hyaluronan by metabolically engineered Bacillus subtilis 168

Low-molecular-weight hyaluronan (LMW-HA) has attracted much attention because of its many potential applications. Here, we efficiently produced specific LMW-HAs from sucrose in Bacillus subtilis. By coexpressing the identified committed genes (tuaD, gtaB, glmU, glmM, and glmS) and downregulating the glycolytic pathway, HA production was significantly increased from 1.01 g L⁻¹ to 3.16 g L⁻¹, with a molecular weight range of 1.40×10⁶–1.83×10⁶ Da. When leech hyaluronidase was actively expressed after N-terminal engineering (1.62×10⁶ U mL⁻¹), the production of HA was substantially increased from 5.96 g L⁻¹ to 19.38 g L⁻¹. The level of hyaluronidase was rationally regulated with a ribosome-binding site engineering strategy, allowing the production of LMW-HAs with a molecular weight range of 2.20×10³–1.42×10⁶ Da. Our results confirm that this strategy for the controllable expression of hyaluronidase, together with the optimization of the HA synthetic pathway, effectively produces specific LMW-HAs, and could also be used to produce other LMW polysaccharides.     

Simultaneous saccharification and fermentation of kraft pulp by recombinant Escherichia coli for phenyllactic acid production

Simultaneous saccharification and fermentation (SSF) of renewable cellulose for the production of 3-phenyllactic acid (PhLA) by recombinant Escherichia coli was investigated. Kraft pulp recovered from biomass fractionation processes was used as a model cellulosic feedstock and was hydrolyzed using 10–50 filter paper unit (FPU) g⁻¹ kraft pulp of a commercial cellulase mixture, which increased the glucose yield from 21% to 72% in an enzyme dose-dependent manner. PhLA fermentation of the hydrolyzed kraft pulp by a recombinant E. coli strain expressing phenylpyruvate reductase from Wickerhamia fluorescens TK1 produced 1.9 mM PhLA. The PhLA yield obtained using separate hydrolysis and fermentation was enhanced from 5.8% to 42% by process integration into SSF of kraft pulp (20 g L⁻¹) in a complex medium (pH 7.0) at 37 °C. The PhLA yield was negatively correlated with the initial glucose concentration, with a five-fold higher PhLA yield observed in culture medium containing 10 g L⁻¹ glucose compared to 100 g L⁻¹. Taken together, these results suggest that the PhLA yield from cellulose in kraft pulp can be improved by SSF under glucose-limited conditions.     

A new bioprocess for the production of prebiotic lactosucrose by an immobilized β-galactosidase

A new bioprocess for the synthesis of lactosucrose was studied using a covalently immobilized β-galactosidase on macrospheres of chitosan. The effects of temperature and pH on the production of lactosucrose and other oligosaccharides were evaluated. At 30 °C and pH 7.0, the maximum concentration of lactosucrose reached to 79 g L⁻¹. The change of the reaction conditions allowed to modify the qualitative profile of the final products without quantitative change in the total of oligosaccharides produced. At pH 7 and 30 °C, products profile was 79 g L⁻¹ of lactosucrose, 37 g L⁻¹ of galactooligosaccharides and 250 g L⁻¹ of total oligosaccharides, while at pH 5 and 64 °C the concentrations for the same compounds were 40, 62 and 250 g L⁻¹, respectively. The immobilization increased the thermal stability up to 260-fold. Using 300 g L⁻¹ of sucrose and 300 g L⁻¹ of lactose, and 8.5 mg of chitosan mL⁻¹, 30 cycles of reuse were performed and the biocatalyst kept the maximal lactosucrose synthesis. These results fulfill some important aspects for the enzyme immobilization and oligosaccharides synthesis: the simplicity of the protocols, the high operational stability of the enzyme and the possibility of driving the final products.     

Optimized endodextranase-epoxy CIM® disk reactor for the continuous production of molecular weight-controlled prebiotic isomalto-oligosaccharides

An epoxy-activated monolithic Convective Interaction Media (CIM^®) disk was used for the immobilization of endodextranase D8144 from Penicillium sp. (EC 3.2.1.11) in order to produce on-line isomalto-oligosaccharides (IMOs) from Dextran T40. Enzymatic parameters, molecular weight of IMOs and performance of the IMmobilized Enzymes Reactor (IMER) were investigated. The immobilization yield of enzymes was about 45.3% (w/w), and the real specific activity close to 3.26 U mg⁻¹. The K_m values did not significantly change between free (12.8 g L⁻¹) and immobilized enzymes (14.2 g L⁻¹), due to the absence of diffusional limitation. The IMER system presented more than 80% of its residual activity after 5000 column volumes, highlighting the high stability of the immobilized endodextranases. Response surface methodology was used to enhance the performance of the IMER. Depending on dextran concentrations and flow rates, specific patterns of IMOs distributions were observed during the enzymatic hydrolysis. Finally, prebiotic activity was also investigated on IMOs produced by medium conditions (flow rate 0.3 mL min⁻¹ and dextran concentrations 4% w/w) against Lactobacillus rhamnosus GG (ATCC 53103). Their scores were at least as good as two commercialized fructo-oligosaccharides (FOS), Fibrulose^® F97 and Orafti^® P95.     

Design,synthesis and structure–activity relationship of novel diphenylamine derivatives

Diphenylamine derivatives have been reported with good fungicidal, insecticidal, acaricidal, rodenticidal and/or herbicidal activities. To find new lead compound of this kind, a series of novel diphenylamine derivatives were designed and synthesized by the approach of Intermediate Derivatization Methods. All compounds were identified by ¹H NMR and elemental analysis. Bioassays demonstrated that some compounds substituted at 2,4,6-positions or 2,4,5-positions of phenyl ring B exhibited excellent fungicidal activities. The optimal compounds P30 and P33 showed 80% and 85% control respectively against cucumber downy mildew at 12.5 mg L⁻¹, both 100% control against rice blast at 0.3 mg L⁻¹ and both 100% control against cucumber gray mold at 0.9 mg L⁻¹. The relationship between structure and fungicidal activities was discussed as well.     

Continuous succinic acid fermentation by Actinobacillus succinogenes

Fermentations were performed in an external recycle bioreactor using CO₂ and d-glucose at feed concentrations of 20 and 40 g L⁻¹. Severe biofilm formation prevented kinetic analysis of suspended cell (‘chemostat’) fermentation, while perlite packing enhanced the volumetric productivity by increasing the amount of immobilised cells. The highest productivity of 6.35 g L⁻¹ h⁻¹ was achieved at a dilution rate of 0.56 h⁻¹. A constant succinic acid yield of 0.69 ± 0.02 g/(g of glucose consumed) was obtained and found to be independent of the dilution rate, transient state and extent of biofilm build-up – approximately 56% of the carbon that formed phosphoenolpyruvate ended up as succinate. Byproduct analysis indicated that pyruvate oxidation proceeded solely via the formate-lyase pathway. Cell growth and corresponding biofilm formation were rapid at dilution rates higher than 0.35 h⁻¹ when the product concentrations were low (succinic acid < 10 g L⁻¹), while minimal growth was observed at succinic acid concentrations above this threshold.     

Isolation and bioelectrochemical characterization of novel fungal sources with oxidasic activity applied in situ for the cathodic oxygen reduction in microbial fuel cells

Brazilian filamentous fungi Rhizopus sp. (SIS-31), Aspergillus sp. (SIS-18) and Penicillium sp. (SIS-21), sources of oxidases were isolated from Caatinga's soils and applied during the in situ cathodic oxygen reduction in fuel cells. All strains were cultivated in submerged cultures using an optimized saline medium enriched with 10 g L⁻¹ of glucose, 3.0 g L⁻¹ of peptone and 0.0005 g L⁻¹ of CuSO₄ as enzyme inducer. Parameters of oxidase activity, glucose consumption and microbial growth were evaluated. In-cell experiments evaluated by chronoamperometry were performed and two different electrode compositions were also compared. Maximum current densities of 125.7, 98.7 and 11.5 μA cm⁻² were observed before 24 h and coulombic efficiencies of 56.5, 46.5 and 23.8% were obtained for SIS-31, SIS-21 and SIS-18, respectively. Conversely, maximum power outputs of 328.73, 288.80 and 197.77 mW m⁻³ were observed for SIS-18, SIS-21 and SIS-31, respectively. This work provides the primary experimental evidences that fungi isolated from the Caatinga region in Brazil can serve as efficient biocatalysts during the oxygen reduction in air-cathodes to improve electricity generation in MFCs.