Simultaneous enhancement of CO2 fixation and lutein production with thermo-tolerant Desmodesmus sp. F51 using a repeated fed-batch cultivation strategy

This study aimed to improve lutein production using a thermo-tolerant lutein-rich microalga Desmodesmus sp. F51. To achieve this goal, four fed-batch cultivation strategies were investigated for CO₂ fixation and lutein production of Desmodesmus sp. F51. Among them, Fed-batch IV showed the best performance, giving the highest CO₂ fixation rate and lutein productivity of 1582.4 mg/L/d and 3.91 mg/L/d, respectively. Both increasing the light intensity and limiting the nutrients led to a lower carotenoids content in the microalga, with a higher proportion of lutein and lower proportion of β-carotene being obtained in the carotenoids. The carotenoid present in the biomass was mainly lutein, accounting for 50–66% of total carotenoids. Repeated operations of the Fed-batch IV strategy could effectively improve CO₂ fixation and lutein production of Desmodesmus sp. F51, giving the best results of 1826.0 mg/L/d, and 4.61 mg/L/d, respectively. This performance is better than most of the previously reported values.     

Cultivation of Chlorella vulgaris in tubular photobioreactors: A lipid source for biodiesel production

Chlorella vulgaris was cultivated in two different 2.0 L-helicoidal and horizontal photobioreactors at 5 klux using the bicarbonate contained in the medium and ambient air as the main CO₂ sources. The influence of bicarbonate concentration on biomass growth as well as lipid content and profile was first investigated in shake flasks, where the stationary phase was achieved in about one half the time required by the control. The best NaHCO₃ concentration (0.2 g L⁻¹) was then used in both photobioreactors. While the fed-batch run performed in the helicoidal photobioreactor provided the best result in terms of biomass productivity, which was (84.8 mg L⁻¹ d⁻¹) about 2.5-fold that of the batch run, the horizontal configuration ensured the highest lipid productivity (10.3 mg L⁻¹ d⁻¹) because of a higher lipid content of biomass (22.8%). These preliminary results suggest that the photobioreactor configuration is a key factor either for the growth or the composition of this microalga. The lipid quality of C. vulgaris biomass grown in both photobioreactors is expected to meet the standards for biodiesel, especially in the case of the helicoidal configuration, provided that further efforts will be made to optimize the conditions for its production as a biodiesel source.     

Continuous production of selenomethionine-enriched Chlorella sorokiniana biomass in a photobioreactor

This article describes the enrichment of the fresh-water green microalga Chlorella sorokiniana in selenomethionine (SeMet). The microalga was cultivated in a 2.2 L glass-vessel photobioreactor, in a culture medium supplemented with selenate (SeO₄^2?) concentrations ranging from 5 to 50 mg L^?1. Although selenate exposure lowered culture viability, C. sorokiniana grew well at all tested selenate concentrations, however cultures supplemented with 50 mg L^?1 selenate did not remain stable at steady state. A suitable selenate concentration in fresh culture medium for continuous operation was determined, which allowed stable long-term cultivation at steady state and maximal SeMet productivity. In order to do that, the effect of dilution rate on biomass productivity, viability and SeMet content of C. sorokiniana at several selenate concentrations were determined in the photobioreactor. A maximal SeMet productivity of 21 μg L^?1 day^?1 was obtained with 40 mg L^?1 selenate in the culture medium. Then a continuous cultivation process at several dilution rates was performed at 40 mg L^?1 selenate obtaining a maximum of 246 μg L^?1 day^?1 SeMet at a low dilution rate of 0.49 day^?1, calculated on total daily effluent volume. This paper describes for the first time an efficient long-term continuous cultivation of C. sorokiniana for the production of biomass enriched in the high value amino acid SeMet, at laboratory scale.     

Effect of lignocellulose degradation products on microbial biomass and lipid production by the oleaginous yeast Cryptococcus curvatus

This work investigated effects of lignocellulose degradation products on cell biomass and lipid production by Cryptococcus curvatus. Furfural was found to have the strongest inhibitory effect. For the three phenolic compounds tested, vanillin was the most toxic, while PHB and syringaldehyde showed comparable inhibitions in the concentration range of 0–1.0 g/L. Generally little significant differences on the relative cell biomass and lipid contents at the same concentrations of tested compounds were observed between glucose and xylose as a sole carbon source. At 1.0 g/L of furfural, the cell biomass and lipid content decreased by 78.4% and 61.0% for glucose as well as 72.0% and 59.3% for xylose, respectively. C. curvatus ceased to grow at concentrations of PHB over 1.0 g/L or vanillin over 1.5 g/L. The strain could survive in the presence of syringaldehyde up to 2.0 g/L for glucose or 1.5 g/L for xylose. The compounds’ negative impact was reduced by an increase in inoculum size and a 10% (v/v) seed was detected to be optimal for cell biomass and lipid production. The results demonstrated C. curvatus could effectively utilize most of the dominant monosaccharides and cellobiose existing in lignocellulosic biomass hydrolysate in the presence of toxic compounds.     

A laboratory study of producing docosahexaenoic acid from biodiesel-waste glycerol by microalgal fermentation

Crude glycerol is the primary by-product in the biodiesel industry, which is too costly to be purified into to higher quality products used in the health and cosmetics industries. This work investigated the potential of using the crude glycerol to produce docosahexaenoic acid (DHA, 22:6 n-3) through fermentation of the microalga Schizochytrium limacinum. The results showed that crude glycerol supported alga growth and DHA production, with 75–100 g/L concentration being the optimal range. Among other medium and environmental factors influencing DHA production, temperature, trace metal (PI) solution concentration, ammonium acetate, and NH₄Cl had significant effects (P < 0.1). Their optimal values were determined 30 mL/L of PI, 0.04 g/L of NH₄Cl, 1.0 g/L of ammonium acetate, and 19.2 °C. A highest DHA yield of 4.91 g/L with 22.1 g/L cell dry weight was obtained. The results suggested that biodiesel-derived crude glycerol is a promising feedstock for production of DHA from heterotrophic algal culture.     

Efficient oleaginous yeasts for lipid production from lignocellulosic sugars and effects of lignocellulose degradation compounds on growth and lipid production

Microbial lipid production using lignocellulosic biomass is considered an alternative for biodiesel production. In this study, 418 yeast strains were screened to find efficient oleaginous yeasts which accumulated large quantities of lipid when cultivated in lignocellulosic sugars. Preliminary screening by Nile red staining revealed that 142 strains contained many or large lipid bodies. These strains were selected for quantitative analysis of lipid accumulation by shaking flask cultivation in nitrogen-limited medium II containing 70 g/L glucose or xylose or mixture of glucose and xylose in a ratio of 2:1. Rhodosporidium fluviale DMKU-SP314 produced the highest lipid concentration of 7.9 g/L when cultivated in the mixture of glucose and xylose after 9 days of cultivation, which was 55.0% of dry biomass (14.3 g/L). The main composition of fatty acids were oleic acid (40.2%), palmitic acid (25.2%), linoleic acid (17.9%) and stearic acid (11.1%). Moreover, the strain DMKU-SP314 could grow and produce lipid in a medium containing predominantly lignocellulose degradation products, namely, acetic acid, formic acid, furfural, 5-hydroxymethylfurfural (5-HMF) and vanillin, with however, some inhibitory effects. This strain showed high tolerance to acetic acid, 5-HMF and vanillin. Therefore, R. fluviale DMKU-SP314 is a promising strain for lipid production from lignocellulosic hydrolysate.     

Dual purpose system that treats anaerobic effluents from pig waste and produce Neochloris oleoabundans as lipid rich biomass

Dual purpose systems that treat wastewater and produce lipid rich microalgae biomass have been indicated as an option with great potential for production of biodiesel at a competitive cost. The aim of the present work was to develop a dual purpose system for the treatment of the anaerobic effluents from pig waste utilizing Neochloris oleoabundans and to evaluate its growth, lipid content and lipid profile of the harvested biomass and the removal of nutrients from the media. Cultures of N. oleoabundans were established in 4 L flat plate photobioreactors using diluted effluents from two different types of anaerobic filters, one packed with ceramic material (D1) and another one packed with volcanic gravel (D2). Maximum biomass concentration in D1 was 0.63 g L⁻¹ which was significantly higher than the one found in D2 (0.55 g L⁻¹). Cultures were very efficient at nutrient removal: 98% for NNH₄⁺ and 98% for PO₄³⁻. Regarding total lipid content, diluted eflluents from D2 promoted a biomass containing 27.4% (dry weight) and D1 a biomass containing 22.4% (dry weight). Maximum lipid productivity was also higher in D2 compared to D1 (6.27 ± 0.62 mg L⁻¹ d⁻¹ vs. 5.12 ± 0.12 mg L⁻¹ d⁻¹). Concerning the FAMEs profile in diluted effluents, the most abundant one was C18:1, followed by C18:2 and C16:0. The profile in D2 contained less C18:3 (linolenic acid) than the one in D1 (4.37% vs. 5.55%). In conclusion, this is the first report demonstrating that cultures of N. oleoabundans treating anaerobic effluents from pig waste are very efficient at nutrient removal and a biomass rich in lipids can be recovered. The maximum total lipid content and the most convenient FAMEs profile were obtained using effluents from a digester packed with volcanic gravel.     

Kinetic modeling and implementation of superior process strategies for β-galactosidase production during submerged fermentation in a stirred tank bioreactor

This paper reports development and implementation of superior fermentation strategies for β-galactosidase production by Lactobacillus acidophilus in a stirred-tank bioreactor. Process parameters (aeration and agitation) were optimized for the process by application of Central Composite Design. Aeration rate of 0.5 vvm and agitation speed of 250 rpm were most suitable for β-galactosidase production (2001.2 U/L). Further improvement of the operation in pH controlled environment resulted in 2135 U/L of β-galactosidase with productivity of 142.39 U/L h. Kinetic modeling for biomass and enzyme production and substrate utilization were carried out at the aforementioned pH controlled conditions. The logistic regression model (X₀ = 0.01 g/L; X_max = 2.948 g/L; μ_max = 0.59/h; R² = 0.97) was used for mathematical interpretation of biomass production. Mercier's model proved to be better than Luedeking–Piret model in describing β-galactosidase production (P₀ = 0.7942 U/L; P_max = 2169.3 U/L; P_r = 0.696/h; R² = 0.99) whereas the latter was more efficient in mathematical illustration of lactose utilization (m = 0.187 g/g h; Y_x/s = 0.301 g/L; R² = 0.98) among the two used in this study. Strategies like fed-batch fermentation (3694.6 U/L) and semi-continuous fermentation (5551.9 U/L) further enhanced β-galactosidase production by 1.8 and 2.8 fold respectively.     

Statistical media optimization for growth and PHB production from methanol by a methylotrophic bacterium

Media components were optimized by statistical design for cell growth and PHB production of Methylobacterium extorquens DSMZ 1340. Four important components of growth media were optimized by central composite design. The growth increased from an OD = 1.35 for Choi medium as control to an OD = 2.15 for optimal medium. Then media components for PHB production were optimized. Optimization of five important factors was conducted by response surface method. The optimal composition of PHB production medium was found to be at 7.8 (g/L) Na₂HPO₄ · 12H₂O, and surprisingly at zero concentration of (NH₄)₂SO₄, KH₂PO₄, MgSO₄ and MnSO₄. The PHB production was found to be 2.95 (g/L) at this medium. RSM results indicated that a deficiency of nitrogen and magnesium is crucial for PHB accumulation in this microorganism. Also, PHB production was carried out in a 5 L fermentor at the optimum condition which resulted in 9.5 g/L PHB and 15.4 g/L cell dry weight with 62.3% polymer content.     

Batch culture and repeated-batch culture of Cunninghamella bainieri 2A1 for lipid production as a comparative study

This research was performed based on a comparative study on fungal lipid production by a locally isolated strain Cunninghamella bainieri 2A1 in batch culture and repeated-batch culture using a nitrogen-limited medium. Lipid production in the batch culture was conducted to study the effect of different agitation rates on the simultaneous consumption of ammonium tartrate and glucose sources. Lipid production in the repeated-batch culture was studied by considering the effect of harvesting time and harvesting volume of the culture broth on the lipid accumulation. The batch cultivation was carried out in a 500 ml Erlenmeyer flask containing 200 ml of the fresh nitrogen-limited medium. Microbial culture was incubated at 30 °C under different agitation rates of 120, 180 and 250 rpm for 120 h. The repeated-batch culture was performed at three harvesting times of 12, 24 and 48 h using four harvesting cultures of 60%, 70%, 80% and 90%. Experimental results revealed that nitrogen source (ammonium tartrate) was fully utilized by C. bainieri 2A1 within 24 h in all agitation rates tested. It was also observed that a high amount of glucose in culture medium was consumed by C. bainieri 2A1 at 250 rpm agitation speed during the batch fermentation. Similar results showed that the highest lipid concentration of 2.96 g/L was obtained at an agitation rate of 250 rpm at 120 h cultivation time with the maximum lipid productivity of 7.0 × 10⁻² mg/ml/h. On the other hand, experimental results showed that the highest lipid concentration produced in the repeated-batch culture was 3.30 g/L at the first cycle of 48 h harvesting time using 70% harvesting volume, while 0.23 g/L gamma-linolenic acid (GLA) was produced at the last cycle of 48 h harvesting time using 80% harvesting volume.     

Development of Halomonas TD01 as a host for open production of chemicals

Genetic engineering of Halomonas spp. was seldom reported due to the difficulty of genetic manipulation and lack of molecular biology tools. Halomonas TD01 can grow in a continuous and unsterile process without other microbial contaminations. It can be therefore exploited for economic production of chemicals. Here, Halomonas TD01 was metabolically engineered using the gene knockout procedure based on markerless gene replacement stimulated by double-strand breaks in the chromosome. When gene encoding 2-methylcitrate synthase in Halomonas TD01 was deleted, the conversion efficiency of propionic acid to 3-hydroxyvalerate (3HV) monomer fraction in random PHBV copolymers of 3-hydroxybutyrate (3HB) and 3HV was increased from around 10% to almost 100%, as a result, cells were grown to accumulate 70% PHBV in dry weight (CDW) consisting of 12 mol% 3HV from 0.5 g/L propionic acid in glucose mineral medium. Furthermore, successful deletions on three PHA depolymerases eliminate the possible influence of PHA depolymerases on PHA degradation in the complicated industrial fermentation process even though significant enhanced PHA content was not observed. In two 500 L pilot-scale fermentor studies lasting 70 h, the above engineered Halomonas TD01 grew to 112 g/L CDW containing 70 wt% P3HB, and to 80 g/L CDW with 70 wt% P(3HB-co-8 mol% 3HV) in the presence of propionic acid. The cells grown in shake flasks even accumulated close to 92% PHB in CDW with a significant increase of glucose to PHB conversion efficiency from around 30% to 42% after 48 h cultivation when pyridine nucleotide transhydrogenase was overexpressed. Halomonas TD01 was also engineered for producing a PHA regulatory protein PhaR which is a robust biosurfactant.     

Enhanced production of insect raw-starch-digesting alpha-amylase accompanied by high erythritol synthesis in recombinant Yarrowia lipolytica fed-batch cultures at high-cell-densities

Recently we reported on raw-starch-digesting ability of alpha-amylase from an insect Sitophilus oryzae (SoAMY) expressed in recombinant Yarrowia lipolytica cells, and demonstrated its usefulness in simultaneous saccharification and fermentation processes with industrial yeasts. In this study we applied fed-batch cultures of Y. lipolytica 4.29 strain reaching high-cell-densities (up to 70 [g_DCW/L]), to enhance SoAMY production. SoAMY activity in the medium reached the peak value of 22,979.23 ± 184 [AU/L], at volumetric productivity of 121.58 ± 1.75 [AU/L/h], and yield of 71.83 ± 3.08 [AU/g_glycerol], constituting roughly 160-fold improvement, compared to the best previous result. The cultivations were accompanied by high production of erythritol (83.58 [g/L]), at the marginal production of mannitol (5.46 [g/L]). Elementary analyses of media constituents, the enzyme and the yeast biomass gave better insight into carbon and nitrogen fluxes distribution. Due to application of genetic engineering and bioprocess engineering strategies, the insect-derived enzyme can be produced at the quantities competitive to microbial catalysts.     

Enhancing production of prodigiosin from Serratia marcescens C3 by statistical experimental design and porous carrier addition strategy

Serratia marcescens C3 produces a natural red-pigment, prodigiosin, which exhibits immunosuppressive properties, in vitro apoptotic effects, and in vivo anti-tumor activities. This work seeks to improve the production of prodigiosin by S. marcescens C3 using various strategies. Starch and peptone were identified as the optimized carbon and nitrogen sources for the production of prodigiosin, yielding a prodigiosin concentration of 2.3 g/L. This value was significantly increased to 6.7 g/L using a carbon/nitrogen ratio of 6/4 (starch/peptone = 16 g/L/10.67 g/L). To enhance prodigiosin production even further, a statistical experimental design methodology was utilized to optimize the composition of the culture medium that is utilized in the production of prodigiosin. Prodigiosin production of 7.07 g/L was achieved when the concentrations of two trace compounds, FeSO₄·4H₂O and MnSO₄·4H₂O, were optimized using the statistical experimental design methodology. Their optimal concentrations were 0.56 mM and 3.25 mM, respectively. Ultimately, the production of prodigiosin was increased from 2.3 g/L to 15.6 g/L, or by a factor of nearly seven by immobilizing microorganisms in 3% calcium alginate beads.     

Pectinase production by Aspergillus niger LB-02-SF is influenced by the culture medium composition and the addition of the enzyme inducer after biomass growth

The production of pectinase by Aspergillus niger LB-02-SF was focused on a submerged cultivation, before it was evaluated in a solid-state process. This study involved the creation of a defined culture medium and an evaluation of the effects of the addition of the enzyme inducer, citrus pectin, to the medium after the intense biomass growth phase. A culture medium formulated without glucose allowed a reduction of biomass growth and greater pectinase production, facilitated by the control of process parameters such as mixing, pH and oxygen supply. The addition of pectin when a minimum pH of 2.7 was reached at 22 h of cultivation did not affect fungal growth. The maximum biomass concentration was 11.0 g/L at 48 h, a value similar to that observed for the control, in which pectin was included in the medium at the beginning of the process (11.5 g/L, at 41 h). However, this condition favored the production of 14 U/mL pectinase, which was approximately 40% higher than the value observed for the control. These results show that pectinase production by A. niger in a submerged cultivation is strongly affected by the medium composition as well as the delayed addition of pectin to the fermentation broth.     

Growth and loss of distal tissue in blades of Lessonia nigrescens and Lessonia trabeculata (Laminariales)

Meristematic growth and loss of distal tissue from blades of two ecologically important species in the south-east Pacific, Lessonia nigrescens and Lessonia trabeculata, was evaluated during 1 year. Comparative growth was determined by a hole-punch method, loss of distal tissue from the blades was determined by subtracting final blade length (with loss) from expected blade lengths (without loss); growth and tissue loss were transformed to fresh biomass units for calculation of inter-algae differences. The results showed that blade elongation rate increased at the beginning of spring, and declined towards the end of summer, with mean values between 0.40 and 0.08 cm day⁻¹ for L. nigrescens, and 0.65–0.17 cm day⁻¹ for L. trabeculata. Loss of distal tissue varied seasonally when examined as length units for both species; with mean values between 0.24 and 0.10 cm day⁻¹ for L. nigrescens, and 0.51–0.25 cm day⁻¹ for L. trabeculata. Variations in fresh biomass units were only observed in Lessonia trabeculata, increasing in spring, with mean values to 0.13 g (fresh weight) day⁻¹. Annual growth and loss of distal tissue were higher in L. trabeculata (0.41 and 0.39 cm day⁻¹, respectively) than in L nigrescens (0.19 and 0.15 cm day⁻¹). When growth and tissue loss were considered as fresh biomass, monthly gains significantly outweighed loss of distal tissue in both species, but parallel results based on length data followed a different trend. L. trabeculata released about 50% of its growth biomass as particulate organic matter, while the comparative value for L. nigrescens was about 20%.     

Optimisation and scale-up of α-glucuronidase production by recombinant Saccharomyces cerevisiae in aerobic fed-batch culture with constant growth rate

α-Glucuronidase (EC 3.2.1.139) of family GH 115 from Scheffersomyces stipitis is a valuable enzyme for the modification of water-soluble xylan into insoluble biopolymers, due to its unique ability to act on polymeric xylans. The influence of growth rate on the production of α-glucuronidase by recombinant Saccharomyces cerevisiae MH1000pbk10D-glu in glucose-limited fed-batch culture was studied at 14 and 100 L scale. At and below the critical specific growth rate (μ_crit) of 0.12 h⁻¹ at 14 L scale, the biomass yield coefficient (Y_x/s) remained constant at 0.4 g g⁻¹ with no ethanol production, whereas ethanol yields relative to biomass (k_eth/x) of up to 0.54 g g⁻¹ and a steady decrease in Y_x/s were observed at μ > 0.12 h⁻¹. Production of α-glucuronidase was growth associated at a product yield (k_α-glu/x) of 0.45 mg g⁻¹, with the highest biomass (37.35 g/L) and α-glucuronidase (14.03 mg/L) concentrations, were recorded during fed-batch culture at or near to μ_crit. Scale-up with constant k_La from 14 to 100 L resulted in ethanol concentrations of up to 2.5 g/L at μ = 0.12 h⁻¹. At this scale, α-glucuronidase yield could be maximised at growth rates below μ_crit, to prevent localised high glucose concentration pockets at the feed entry zone that would induce oxido-reductive metabolism. This is the first report where recombinant production of α-glucuronidase (EC 3.2.1.139) by S. cerevisiae was optimised for application at pilot scale.     

Effect of modified MRS medium on production and purification of antimicrobial peptide ST4SA produced by Enterococcus mundtii

Highest antimicrobial activity of peptide ST4SA (51,200 AU/mL) was recorded after 14 h of growth in MRS broth with optimal production at pH 6.0 or 6.5. Growth of strain ST4SA in the presence of tryptone, yeast extract, or a combination of the two, yielded 102,400 AU/mL. An increase in production of peptide ST4SA to 102,400 AU/mL was recorded in the presence of 20.0 g/L fructose, but decreased to 25,600 AU/mL in the presence of lactose (20.0 g/L) or mannose (20.0 g/L) as sole carbon source. Lower activity (25,600 AU/mL) was recorded when 2.0 g/L K₂HPO₄ was replaced by 2.0 g/L KH₂PO₄ in MRS broth. An increase of K₂HPO₄ to 10.0 g/L and 20.0 g/L resulted in higher activity (102,400 AU/mL). Addition of glycerol to MRS broth had a negative effect on peptide ST4SA production. Production of peptide ST4SA required the presence of magnesium sulphate, manganese sulphate and 5.0 g/L sodium acetate. Exclusion of tri-ammonium citrate from the medium resulted in reduction of activity to 3,200 AU/mL. Maximum activity (102,400 AU/mL) was recorded in MRS supplemented with 1.0 ppm Vit. C, DL-6,8-thioctic acid or thiamine, respectively. Growth of Listeria ivanovii susbp. ivanovii ATCC 19119 in the presence of peptide ST4SA (12,800 AU/mL) resulted in 99% cell lysis after 18 h. Improved production of peptide ST4SA was recorded in MRS broth (Biolab) pre-treated with Amberlite XAD-1180. Precipitation with ammonium sulphate, followed by gel filtration chromatography, yielded the highest level of peptide ST4SA. This paper describes the partially deproteination of growth medium to facilitate peptide ST4SA purification.     

Evaluation of single cell oil from Aureobasidium pullulans var. melanogenum P10 isolated from mangrove ecosystems for biodiesel production

In this study, the yeast strain P10 which was identified to be a member of Aureobasidium pullulans var. melanogenum isolated from the mangrove ecosystems was found to be able to accumulate high content of oil in its cells. After optimization of the medium for lipid production and cell growth by the yeast strain P10, it was found that 8.0 g of glucose per 100 ml, 0.02 g of yeast extract per 100 ml, 0.02 g of ammonium sulfate per 100 ml, pH 6.0 in the medium were the most suitable for lipid production. During 10-l fermentation, a titer was 66.3 g oil per 100 g of cell dry weight, cell mass was 1.3 g per 100 ml, a yield was 0.11 g of oil per g of consumed sugar and a productivity was 0.0009 g of oil per g of consumed sugar per h within 120 h. At the same time, only 0.07 g of reducing sugar per 100 ml was left in the fermented medium. The compositions of the fatty acids produced were C_16:0 (26.7%), C_16:1(1.7%), C_18:0 (6.1%), C_18:1 (44.5%), and C_18:2 (21.0%). The biodiesel produced from the extracted lipid could be burnt well.     

Optimization of the medium for glutathione production in Saccharomyces cerevisiae

As a powerful statistical experimental design, uniform design (UD) method has been successfully applied in various fields such as fermentation industry, pharmaceuticals, and others. In this paper, UD was applied to optimize the medium composition for glutathione production in shake-flask culture of Saccharomyces cerevisiae T65. The experiments of nine factors (glucose, yeast extract, peptone, malt extract, molasses, MgSO₄, ZnSO₄, (NH₄)₂HPO₄ and thiamine) and nine levels were carried out according to the uniform design table U₂₇(9⁹). The experimental data was analyzed to obtain the regression model and the optimal medium composition was achieved by optimization with UD 3.0 software. The optimal medium consisted of 70 g/L glucose, 3 g/L yeast extract, 5 g/L peptone, 70 g/L malt extract, 20 g/L molasses, 5.6 g/L MgSO₄, 16 mg/L ZnSO₄, 7 g/L (NH₄)₂HPO₄ and 0.2 mg/L thiamine. The GSH yield at the optimal point achieved 74.6 mg/L, which was 1.81 times higher than that of the control. The application of UD method resulted in enhancement in GSH production.     

l-Lactic acid production from liquefied cassava starch by thermotolerant Rhizopus microsporus: Characterization and optimization

The thermotolerant Rhizopus microsporus DMKU 33 capable of producing l-lactic acid from liquefied cassava starch was isolated and characterized for its phylogenetic relationship and growth temperature and pH ranges. The concentrations of (NH₄)₂SO_4, KH₂PO₄, MgSO₄ and ZnSO₄·7H₂O in the fermentation medium was optimized for lactic acid production from liquefied cassava starch by Rhizopus microsporus DMKU 33 in shake-flasks at 40 °C. The fermentation was then studied in a stirred-tank bioreactor with aeration at 0.75 vvm and agitation at 200 rpm, achieving the highest lactic acid production of 84 g/L with a yield of 0.84 g/g at pH 5.5 in 3 days. Lactic acid production was further increased to 105–118 g/L with a yield of 0.93 g/g and productivity of 1.25 g/L/h in fed-batch fermentation. R. microsporus DMKU 33 is thus advantageous to use in simultaneous saccharification and fermentation for l-lactic acid production from low-cost starchy substrates.