Ultrasound assisted synthesis of CaF2:Eu3+ phosphor nanoparticles

In this work, the optical and structural properties of ultrasonically prepared CaF₂:Eu³⁺ nanoparticles have been reported. Ultrasonically prepared CaF₂:Eu³⁺ phosphor shows orange, red emission bands at 591 nm and 612 nm, respectively, when it is excited by 394 light‐emitting diode (LED) excitation wavelengths. Further phosphor materials are well characterized by X‐ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy and transmission electron microscopy (TEM) techniques to confirm the phase purity, metal oxygen (MO) bonding and crystallites size of the materials. Here synthesized materials show a tube‐like structure under 100 nm resolution and 0.1 mol% is the best doping value of the europium ion (Eu³⁺) in calcium fluoride (CaF₂) that shows highest intensity when prepared with an ultrasound assisted method.     

Microwave‐assisted sintering synthesis of greenish‐yellow emitting Sr2SiO4:Eu2+ phosphors

Europium ion (Eu²⁺) doped Sr₂SiO₄ phosphors with greenish‐yellow emission were synthesized using microwave‐assisted sintering. The phase structure and photoluminescence (PL) properties of the obtained phosphor samples were investigated. The PL excitation spectra of the Sr₂SiO₄:Eu²⁺ phosphors exhibited a broad band in the range of 260 nm to 485 nm with a maximum at 361 nm attributed to the 5f‐4d allowed transition of the Eu²⁺ ions. Under an excitation at 361 nm, the Sr₂SiO₄:Eu²⁺ phosphor exhibited a greenish‐yellow emission peak at 541 nm with an International‐Commission‐on‐Illumination (CIE) chromaticity of (0.3064, 0.4772). The results suggest that the microwave‐assisted sintering method is promising for the synthesis of phosphors owing to the decreased sintering time without the use of additional reductive agents.     

Synthesis and photoluminescence properties of Eu3+‐activated Ba2Mg(PO4)2 phosphor

In this paper, we have reported the photoluminescence (PL) properties of the Ba₂Mg(PO₄)₂:Eu³⁺ phosphor synthesized using a wet chemical method. The preliminary scanning electron microscopy (SEM) investigation of the sample revealed irregular surface morphology with particle sizes in the 10–50 μm range. The strongest PL excitation peak was observed at 396 nm. The emission spectra indicated that this phosphor can be effectively excited by the 396 nm wavelength. Upon 396 nm excitation, the emission spectrum showed characteristics peaks located at 592 nm and 615 nm. These intense orange‐red emission peaks were obtained due to f→f transitions of Eu³⁺ ions. The emission peak at 592 nm is referred to as the magnetic dipole ⁵D₀→⁷F₁ transition and the emission peak at 615 nm corresponded to the electric dipole ⁵D₀→⁷F₂ transition of Eu³⁺. The Commission Internationale de l’Eclairage (CIE) coordinates of the Ba₂Mg(PO₄)₂:Eu³⁺ phosphor were found to be (0.586, 0.412) for wavelength 592 nm and (0.680, 0.319) for wavelength 615 nm situated at the edge of the CIE diagram, indicating high colour purity of phosphors. Due to the high emission intensity and a good excitation profile, Eu³⁺‐doped Ba₂Mg(PO₄)₂ phosphor may be a promising orange‐red phosphor candidate for solid‐state lighting applications.     

Eu2+ luminescence in SrCaP2O7 pyrophosphate phosphor

A series of Eu²⁺ activated SrCaP₂O₇ pyrophosphate phosphors were synthesized by the modified solid‐state reaction method. The X‐ray diffraction (XRD) and photoluminescence (PL) properties of these phosphors were investigated at room temperature. The excitation spectra indicate that these phosphors can be effectively excited by Hg‐free excitation. The emission spectra exhibit strong blue performance, which is due to the 4f⁶5d¹→4f⁷ transition of Eu²⁺. The Fourier transform infrared spectrum at room temperature was investigated and surface morphology has been studied by scanning electron microscope. The prepared phosphor exhibited intense blue emission at the 427 nm owing to Eu²⁺ ion by Hg‐free excitation at 330 nm, that is, solid‐state lighting excitation. Hence, the availability of such a phosphor will significantly help in the growth of blue‐emitting solid‐state lighting applications. Copyright © 2012 John Wiley & Sons, Ltd.     

Luminescence in Li3Al2(PO4)3:Eu2+

A series of efficient Li₃Al₂(PO₄)₃:Eu²⁺ novel phosphors were synthesized by the facile combustion method. The effects of dopant on the luminescence behavior of Li₃Al₂(PO₄)₃ phosphor were also investigated. The phosphors were characterized by X‐ray diffraction, field emission scanning electron microscope and photoluminescence techniques. The result shows that all samples can be excited efficiently by near‐ultraviolet excitation under 310 nm. The emission was observed for Li₃Al₂(PO₄)₃:Eu²⁺ phosphor at 425 nm, which corresponded to the d → f transition. The concentration quenching of Eu²⁺ was observed in Li₃Al₂(PO₄)₃:Eu²⁺ when the Eu concentration was at 0.5 mol%. The prepared powders exhibited intense blue emission at the 425 nm owing to the Eu²⁺ ion by Hg‐free excitation at 310 nm (i.e., solid‐state lighting excitation). Consequently, the availability of such a phosphor will significantly help in the development of blue‐emitting solid‐state lighting applications. Copyright © 2012 John Wiley & Sons, Ltd.     

Photoluminescence properties of a novel phosphor CaB2O4:Eu3+ under NUV excitation

The new borate phosphor CaB₂O₄:Eu³⁺ was synthesized by solid‐state method and their photoluminescence properties were investigated. The results show that the pure phase of CaB₂O₄ could be available at 900°C, CaB₂O₄:Eu³⁺ phosphor could be effectively excited by the near ultraviolet light (NUV) (392 nm), and the luminescent intensity of CaB₂O₄:Eu³⁺ phosphor reached to the highest when the doped‐Eu³⁺ content was 4 mol%. The emission spectra of CaB₂O₄:Eu³⁺ phosphor could exhibit red emission at 612 nm and orange emission at 588 nm, which are ascribed to the ⁵D₀–⁷F₂ and ⁵D₀–⁷F₁ transitions of Eu³⁺ ions. Copyright © 2009 John Wiley & Sons, Ltd.     

Structural characterization and optical properties of Ca2MgSi2O7:Eu2+,Dy3+ phosphor by solid‐state reaction method

Ca₂MgSi₂O₇:Eu²⁺,Dy³⁺ phosphor was prepared by the solid‐state reaction method under a weak reducing atmosphere. The obtained phosphor was characterized using X‐ray diffraction (XRD), transmission electron microscopy (TEM), field emission scanning electron microscopy (FESEM), energy dispersive X‐ray spectroscopy (EDX) and Fourier transform infrared (FT‐IR) techniques. The phase structure of the Ca₂MgSi₂O₇:Eu²⁺,Dy³⁺ phosphor was akermanite type, which is a member of the melilite group. The surface morphology of the sintered phosphor was not uniform and phosphors aggregated tightly. EDX and FT‐IR spectra confirm the elements present in the Ca₂MgSi₂O₇:Eu²⁺,Dy³⁺ phosphor. Under UV excitation, a broadband emission spectrum was found. The emission spectra observed in the green region centered at 535 nm, which is due to the 4f–5d transition. The mechanoluminescence (ML) intensity of the prepared phosphor increased linearly with increases in the mechanical load. The ML spectra were similar to the photoluminescence (PL), which indicates that ML is emitted from the same emitting center of Eu²⁺ ions as PL. Copyright © 2014 John Wiley & Sons, Ltd.     

Luminescence of the near‐ultraviolet blue‐emitting Ba9Al2Si6O24:Ce3+ phosphor

A near‐ultraviolet (NUV) blue‐emitting phosphor Ba₉Al₂Si₆O₂₄:Ce³⁺ (BAS:Ce³⁺) was synthesized using a high‐temperature solid‐state reaction. BAS:Ce³⁺ had an excitation band peak at about 328 nm and showed a blue emission band. The NUV‐blue emission band had a peak at about 386 nm with a band width of about 60 nm, attributed to the 5d–4f transition of Ce³⁺. Fluorescent decay showed an exponential model with a lifetime of 27.2 nsec. At 150°C, the luminescence intensity decreased to 68.7% compared with the intensity at room temperature.     

Characterization and luminescence properties of CaMgSi2O6:Eu2+ blue phosphor

A blue CaMgSi₂O₆:Eu²⁺ phosphor was prepared by the solid‐state reaction method and the phosphor characterized in terms of crystal structure, particle size, photoluminescence (PL), thermoluminescence (TL) and mechanoluminescence (ML) properties using X‐ray diffraction (XRD), transmission electron microscopy (TEM), PL spectroscopy, TLD reader and ML impact technique. The XRD result shows that phosphor is formed in a single phase and has a monoclinic structure with the space group C2/c. Furthermore, the PL excitation spectra of Eu²⁺‐doped CaMgSi₂O₆ phosphor showed a strong band peak at 356 nm and the PL emission spectrum has a peak at 450 nm. The depths and frequency factors of trap centers were calculated using the TL glow curve by deconvolution method in which the trap depths were found to be 0.48 and 0.61 eV. The formation of CaMgSi₂O₆:Eu²⁺ phosphor was confirmed by Fourier transform infrared spectroscopy. The ML intensity increased linearly with the impact velocity of the piston used to deform the phosphor. It was shown that the local piezoelectricity‐induced electron bombardment model is responsible for the ML emission. Finally, the optical properties of CaMgSi₂O₆:Eu²⁺ phosphors are discussed. Copyright © 2015 John Wiley & Sons, Ltd.     

Optically stimulated luminescence in LiCaAlF6:Eu2+ phosphor

Results on optically stimulated luminescence (OSL) in LiCaAlF₆:Eu²⁺ are reported. Continuous wave OSL signal as recorded using blue (470 nm) stimulation was found to be ~31% that of standard phosphor lithium magnesium phosphate. The rate of OSL depletion for standard phosphor lithium magnesium phosphate is only three times less as compared with that of LiCaAlF₆:Eu²⁺. Strong photoluminescence (PL) in the near ultraviolet region is observed for LiCaAlF₆:Eu²⁺ with the characteristic Eu²⁺ emission at 369 nm for 254 nm excitation. The thermoluminescence (TL) glow peak for LiCaAlF₆:Eu²⁺ was observed at around 180°C. The glow peak was about six times more intense compared with the dosimetric peak of the well known thermoluminescence dosimetric (TLD) phosphor LiF‐TLD 100. Thus this phosphor deserves much more attention than it has received until now and may be useful as a dosimetric material in radiation dosimetry. Copyright © 2015 John Wiley & Sons, Ltd.     

Synthesis and luminescence properties of blue‐emitting phosphor Ca12Al14O32F2:Eu2+ for white light‐emitting diode

A blue‐emitting phosphor Ca₁₂Al₁₄O₃₂F₂:Eu²⁺ was synthesized using a high‐temperature solid‐state reaction under a reductive atmosphere. The X‐ray diffraction measurements indicate that a pure phase Ca₁₂Al₁₄O₃₂F₂:Eu²⁺ can be obtained for low doping concentration of Eu²⁺. The phosphor has a strong absorption in the range 270–420 nm with a maximum at ~340 nm and blue emission in the range 400–500 nm with chromatic coordination of (0.152, 0.045). The optimal doping concentration is ~0.24. In addition, the luminescence properties of the as‐synthesized phosphor were evaluated by comparison with those of Ca₁₂Al₁₄O₃₂Cl₂:Eu²⁺ and the commercially available phosphor BaMgAl₁₀O₁₇:Eu²⁺. The emission intensity of Ca₁₂Al₁₄O₃₂F₂:Eu²⁺ was ~72% that of BaMgAl₁₀O₁₇:Eu²⁺ under excitation at λ = 375 nm. The results indicate that Ca₁₂Al₁₄O₃₂F₂:Eu²⁺ has potential application as a near‐UV‐convertible blue phosphor for white light‐emitting diodes.     

Novel blue‐emitting SrMg2Al16O27:Eu2+ phosphor for solid‐state lighting

Eu²⁺‐activated SrMg₂Al₁₆O₂₇ novel phosphor was synthesized by a combustion method (550°C furnace). The prepared phosphor was first characterized by X‐ray diffraction (XRD) for confirmation of phase purity. SEM analysis showed the morphology of the phosphor. The photoluminescence characteristics showed broad‐band excitation at 324 nm, which was monitored at 465 nm emission wavelength. The SrMg₂Al₁₆O₂₇:Eu²⁺ phosphor shows broad blue emission centred at 465 nm, emitting a blue light corresponding to 4f⁶5d¹ → 4f⁷ transition. Here we report the photoluminescence characteristics of the prepared phosphor and compare it with commercial BAM:Eu²⁺ phosphor. Copyright © 2011 John Wiley & Sons, Ltd.     

Luminescence properties of green‐emitting Ca2MgSi2O7:Eu2+ phosphor by a solid‐state reaction method

A europium (Eu)‐doped di‐calcium magnesium di‐silicate phosphor, Ca₂MgSi₂O₇:Eu²⁺, was prepared using a solid‐state reaction method. The phase structure, particle size, surface morphology, elemental analysis, different stretching mode and luminescence properties were analyzed by X‐ray diffraction (XRD), transmission electron microscopy (TEM), field emission scanning electron microscopy (FESEM) with energy dispersive X‐ray spectroscopy (EDX), Fourier transform infrared (FTIR) spectroscopy, photoluminescence (PL) and mechanoluminescence (ML). The phase structure of Ca₂MgSi₂O₇:Eu²⁺ was an akermanite‐type structure, which belongs to the tetragonal crystallography with space group P4?2₁m; this structure is a member of the melilite group and forms a layered compound. The surface of the prepared phosphor was not found to be uniform and particle distribution was in the nanometer range. EDX and FTIR confirm the components of Eu²⁺‐doped Ca₂MgSi₂O₇ phosphor. Under UV excitation, the main emission peak appeared at 530 nm, belonging to the broad emission ascribed to the 4f⁶5d¹→4f⁷ transition of Eu²⁺. The ML intensity of the prepared phosphor increased linearly with increasing impact velocity. A CIE color chromaticity diagram and ML spectrum confirmed that the prepared Ca₂MgSi₂O₇:Eu²⁺ phosphor would emit green color and the ML spectrum was similar to that of PL, which indicated that ML is emitted from the same center of Eu²⁺ ions. Copyright © 2015 John Wiley & Sons, Ltd.     

Synthesis and luminescence properties of a novel blue emitting phosphor NaMgPO4:Eu2+

A novel blue‐emitting phosphor of Eu²⁺‐activated NaMgPO₄ was prepared by combustion‐assisted synthesis. Sodium dihydrogen phosphate and magnesium nitrate were used as the source of Na, P and Mg, respectively. The ratios of magnesium and phosphorus components that were dissolved into the combustion solution were changed from 1:1 to 1:1.3. Their effect on the crystallinities and photoluminescence spectra of the phosphor particles were investigated. The post‐heated phosphor particles had a broad excitation wavelength that ranged from 240 to 410 nm. The phosphor particles prepared from the combustion solution with a 1:1.2 ratio of magnesium to phosphorus had maximum emission intensity under ultraviolet excitation. The effect of doped Eu²⁺ concentration on the emission intensity of NaMgPO₄:Eu²⁺ was also investigated.     

Design,synthesis and luminescence properties of Ba2YB2O6Cl‐ and Ba2YB2O6F‐based phosphors

Using a high‐temperature solid‐state reaction, the chlorine in Ba₂YB₂O₆Cl is gradually replaced by F, and a new compound with the nominal chemical formula Ba₂YB₂O₆F and two phosphors doped with Ce³⁺ and Eu³⁺, respectively, are obtained. X‐Ray diffraction and photoluminescence spectroscopy are used to characterize the as‐synthesized samples. The as‐synthesized Ba₂YB₂O₆Cl exhibits bright blue emission in the spectral range ~ 330–410 nm with a maximum around 363 nm under X‐ray or UV excitation. Ba₂YB₂O₆F:0.01Ce³⁺ exhibits blue emission in the range ~ 340–570 nm with a maximum around 383 nm. Ba₂YB₂O₆F:0.01Eu³⁺ exhibits a predominantly ⁵D₀–⁷ F₂ emission (~610 nm) and the relative intensities of the ⁵D₀–⁷ F_0,1,2 emissions are tunable under different wavelength UV excitation. The luminescence behaviors of the two phosphors are explained simply in terms of the host composition and site occupancy probability of Ce³⁺ and Eu³⁺, respectively. The results indicate that these phosphors have potential application as a blue phosphor or as a red phosphor. Copyright © 2014 John Wiley & Sons, Ltd.     

Synthesis and characterization of Ba3Si6O12N2:Eu2+ phosphor

Eu²⁺‐doped Ba₃Si₆O₁₂N₂ phosphors were prepared successfully via a modified solid‐state diffusion method. The phosphors were characterized by X‐ray diffraction (XRD), scanning electron microscopy (SEM) and photoluminescence measurements. These phosphors were effectively excited at 355 nm and an intense emission peaking in the range 480 nm to 525 nm in the blue region was observed. The optimized dopant concentration was determined to be 1 mol% of Eu²⁺ ion. The colour coordinates for phosphor were found to be (0.196, 0.326) in the blue region. This phosphor may find application for near‐ultraviolet (NUV) excited lamp phosphors. The thermoluminescence study shows the complex glow curve. Trapping parameters (activation energy and frequency factor) were calculated for individual deconvoluted peaks by Chen's peak shape method, the initial rise method and the whole glow peak method. Copyright © 2015 John Wiley & Sons, Ltd.     

Thermal quenching of luminescence of LiSr4(BO3)3:Eu2+ orange‐emitting phosphor

An orange‐emitting phosphor, Eu²⁺‐activated LiSr₄(BO₃)₃, was synthesized using the conventional solid‐state reaction. The photoluminescence excitation and emission spectra, and temperature dependence of the luminescence intensity of the phosphor were investigated. The results showed that LiSr₄(BO₃)₃:Eu²⁺ could be efficiently excited by incident light of 250–450 nm, and emits a strong orange light. With increasing temperature, the emission bands of LiSr₄(BO₃)₃:Eu²⁺ show an abnormal blue‐shift with broadening bandwidth and decreasing emission intensity. Copyright © 2013 John Wiley & Sons, Ltd.     

Insights into the discrepant luminescence for BaSiO3:Eu2+ phosphors prepared by solid‐state reaction and precipitation reaction methods

Two synthesis routes, solid‐state reaction and precipitation reaction, were employed to prepare BaSiO₃:Eu²⁺ phosphors in this study. Discrepancies in the luminescence green emission at 505 nm for the solid‐state reaction method sample and in the yellow emission at 570 nm for the sample prepared by the precipitation reaction method, were observed respectively. A detail investigation about the discrepant luminescence of BaSiO₃:Eu²⁺ phosphors was performed by evaluation of X‐ray diffraction (XRD), photoluminescence (PL)/photoluminescence excitation (PLE), decay time and thermal quenching properties. The results showed that the yellow emission was generated from the BaSiO₃:Eu²⁺ phosphor, while the green emission was ascribed to a small amount of Ba₂SiO₄:Eu²⁺ compound that was present in the solid‐state reaction sample. This work clarifies the luminescence properties of Eu²⁺ ions in BaSiO₃ and Ba₂SiO₄ hosts.     

Luminescent properties of Ca3SiO4Cl2 co‐doped with Ce3+ and Eu2+ for near‐ultraviolet light‐emitting diodes

Ca₃SiO₄Cl₂ co‐doped with Ce³⁺,Eu²⁺ was prepared by high temperature reaction. The structure, luminescent properties and the energy transfer process of Ca₃SiO₄Cl₂: Ce³⁺,Eu²⁺ were investigated. Eu²⁺ ions can give enhanced green emission through Ce³⁺ → Eu²⁺ energy transfer in these phosphors. The green phosphor Ca_2.9775SiO₄Cl₂:0.0045Ce³⁺,0.018Eu²⁺ showed intense green emission with broader excitation in the near‐ultraviolet light range. A green light‐emitting diode (LED) based on this phosphor was made, and bright green light from this green LED could be observed by the naked eye under 20 mA current excitation. Hence it is considered to be a good candidate for the green component of a three‐band white LED. Copyright © 2015 John Wiley & Sons, Ltd.     

Zn‐doped CaTiO3:Eu3+ red phosphors for enhanced photoluminescence in white LEDs by solid‐state reaction

Zn‐doped CaTiO₃:Eu³⁺ red phosphors for enhanced photoluminescence in white light‐emitting diodes (LEDs) were synthesized by a solid‐state method. The structure and morphology of the obtained phosphor samples were observed by X‐ray diffraction (XRD) and scanning electron microscopy (SEM), and the impact of Ca, Zn and Eu content on their photoluminescence properties was studied. The results indicated that Zn not only participates in the formation of defects in suitable lattice matrices but also has a role in flux in the transformation from ZnO to Zn₂TiO₄, which is beneficial for the enhancement of photoluminescence properties. Photoluminescence test data showed that the Zn‐doped phosphor is excited efficiently by near‐ultraviolet (NUV) light at wavelengths around 398 nm and emits an intense red light with a broad peak around 616 nm corresponding to the ⁵D₀→⁷F₂ transition of Eu³⁺. The intensity of this phosphor emission is three times stronger than that without Zn‐doping. Furthermore, this phosphor has very good thermal stability, high color purity and a low sintered temperature, all of which suggest its potential as a promising red phosphor for white LEDs. Copyright © 2015 John Wiley & Sons, Ltd.