Possibility of using waste tire composites reinforced with rice straw as construction materials

Agricultural lignocellulosic fiber (rice straw)-waste tire particle composite boards were manufactured for use as insulation boards in construction, using the same method as that used in the wood-based panel industry. The manufacturing parameters were: a specific gravity of 0.8 and a rice straw content (10/90, 20/80 and 30/70 by wt.% of rice straw/waste tire particle). A commercial polyurethane adhesive for rubber was used as the composite binder. The water proof, water absorption and thickness swelling properties of the composite boards were better than those of wood particleboard. Furthermore, the flexibility and flexural properties of the composite boards were superior to those of other wood-based panel products. The composite boards also demonstrated good acoustical insulation, electrical insulation, anti-caustic and anti-rot properties. These boards can be used to prevent impact damage, are easily modifiable and are inexpensive. They are able to be used as a substitute for insulation boards and other flexural materials in construction.     

Comparison of genetic damage in Brazilian footwear-workers exposed to solvent-based or water-based adhesive

Research has shown that workers employed in footwear manufacture are at increased risk of some cancers, the strongest evidence being for nasal cancer and leukemia. Footwear-workers are routinely exposed to complex mixtures of solvents in degreasers, cleaners, primers, and adhesives used in the production process as toluene, n-hexane, acetone, and possibly dust particles, additives in shoe materials and degradation products of materials. The recognition of the potential health-hazards of solvent-based adhesives (SBAs) has lead to the development of adhesives with no organic solvents, the water-based adhesives (WBA). We investigated footwear-workers (all males) exposed to SBA (n=29) (for 3.98+/-4.13 years), and WBA (n=16), which had spent the six months previous to the study employed in an experimental section which used only water-based adhesives, although they had previously worked in sections which used solvent-based adhesives (for 5.80+/-4.03 years); 25 healthy subjects were used as controls. The Comet assay and the micronucleus test were used as endpoints, while the traditional parameters for assessing exposure to toluene in organic mixtures by measuring the concentration of urinary hippuric acid were also assessed. Our results showed a significantly lower mean concentration of hippuric acid in the control group than found in the SBA (P<0.001) and WBA (P<0.05) groups. The Comet assay results showed that there was a significant increase in the mean damage index for the SBA (P<0.001) group in comparison to the WBA group and control (P<0.05). For the micronucleus test in binucleated lymphocytes and exfoliated buccal cell, the three groups were not statistically different. Our study demonstrated that water-based adhesives are clearly a better option for safeguarding the health of footwear-workers, even with possibility of isocyanate presence, while the positive results observed in SBA group might be explained by chloroprene presence in the adhesive.     

Solid residues from<Emphasis Type="Italic"> Ruminococcus</Emphasis> cellulose fermentations as components of wood adhesive formulations

Residues from the fermentation of cellulose by the anaerobic bacteria Ruminococcus albus (strain 7) or Ruminococcus flavefaciens (strains FD-1 or B34b) containing residual cellulose, bacterial cells and their associated adhesins, were examined for their ability to serve as components of adhesives for plywood fabrication. The residues contained differing amounts of protein (0.4–4.2% of dry weight), but the ratios of monosaccharides recovered following two-stage treatment of the residue with detergent (pH 7) and TFA were similar for all three strains (0.71 glucose:0.18 xylose:0.08 mannose:0.02 galactose), suggesting similarities in exopolysaccharide composition. Three-ply aspen panels prepared with fermentation residues (FR) displayed better shear strength and wood failure under dry conditions than following a vacuum/pressure/soak/dry treatment, but adhesive properties were inferior to those prepared with conventional phenol-formaldehyde (PF) adhesives. However, panels prepared by incorporating the R. albus 7 FR into PF formulation, at 73% by weight of the total adhesive, exhibited shear strength and wood failure similar to that obtained with PF adhesive alone. Use of residues from fermentations by these bacteria as components of adhesives may add value to biomass fermentations aimed primarily at producing ethanol and other chemical products.Mention of specific products is for informational purposes only and does not imply an endorsement or warranty by the United States Department of Agriculture, over similar products that may also be suitable.     

Modification of lignin for the production of new compounded materials

The cell walls of woody plants are compounded materials made by in situ polymerization of a polyphenolic matrix (lignin) into a web of fibers (cellulose), a process that is catalysed by polyphenoloxidases (laccases) or peroxidases. The first attempt to transform the basic strategy of this natural process for use in human craftsmanship was the ancient lacquer method. The sap of the lacquer tree (Rhus verniciflua) contains large amounts of a phenol (urushiol), a polysaccharide and the enzyme laccase. This oil-in-water emulsion solidifies in the presence of oxygen. The Chinese began using this phenomenon for the production of highly creative artwork more than 6,000 years ago. It was the first example of an isolated enzyme being used as a catalyst to create an artificial plastic compound. In order to apply this process to the production of products on an industrial scale, an inexpensive phenol must be used, which is transferred by an enzyme to active radicals that react with different components to form a compounded material. At present, the following approaches have been studied: (1) In situ polymerization of lignin for the production of particle boards. Adhesive cure is based on the oxidative polymerization of lignin using phenoloxidases (laccase) as radical donors. This lignin-based bio-adhesive can be applied under conventional pressing conditions. The resulting particle boards meet German performance standards. By this process, 80% of the petrochemical binders in the wood-composite industry can be replaced by materials from renewable resources. (2) Enzymatic copolymerization of lignin and alkenes. In the presence of organic hydroperoxides, laccase catalyses the reaction between lignin and olefins. Detailed studies on the reaction between lignin and acrylate monomers showed that chemo-enzymatic copolymerization offers the possibility to produce defined lignin-acrylate copolymers. The system allows control of the molecular weights of the products in a way that has not been possible with chemical catalysts. This is a novel attempt to enzymatically induce grafting of polymeric side chains onto the lignin backbone, and it enables the utilization of lignin as part of new engineering materials. (3) Enzymatic activation of the middle-lamella lignin of wood fibers for the production of wood composites. The incubation of wood fibers with a phenol oxidizing enzyme results in oxidative activation of the lignin crust on the fiber surface. When such fibers are pressed together, boards are obtained which meet the German standards for medium-density fiber boards (MDF). The fibers are bound together in a way that comes close to that by which wood fibers are bound together in naturally grown wood. This process will, for the first time, yield wood composites that are produced solely from naturally grown products without any addition of resins.     

三层法FCCL用合成树脂粘合剂的研究进展

结合三层法FCCL的近期发展情况,对三层法FCCL的结构特点和用于三层法FCCL的高分子合成树脂粘合剂的应用与研发状况进行了介绍,并对近年来应用较广的丙烯酸酯体系的粘合荆、环氧树脂体系的粘合剂、聚酰亚胺体系的粘合剂应用和研究状况作了概括性叙述。     

Clinical aspects of the use of dental adhesive materials in patients with chronic xerostomia

doi: 10.1111/j.1741‐2358.2012.00659.x Clinical aspects of the use of dental adhesive materials in patients with chronic xerostomia Adhesives are commonly used by denture wearers to increase the retention and stability of the complete denture, to improve the chewing and masticatory abilities and to psychologically support the patient to make the complete denture more acceptable. Denture fixatives can be especially recommended for use and to aid retention for patients with dryness of the mouth, poor secretion of saliva and xerostomia (e.g. diabetes mellitus). Dental adhesives may be contaminated with bacteria, yeast and fungi during the manufacturing process, and they have been shown to initiate and promote microbial growth. Some products have been shown to release formaldehyde, which is cytotoxic to cell culture and fibroblasts and is a potent allergen. Patients with chronic xerostomia may use denture adhesives during the course of the treatment and disease. These patients are often immunocompromised, and microorganisms they are exposed to must be considered potential pathogens.     

Mechanical properties of biomimetic tissue adhesive based on the microbial transglutaminase-catalyzed crosslinking of gelatin

Fibrin sealants are a type of soft tissue adhesive that employs biochemical reactions from the late stages of the blood coagulation cascade. Intrinsic to these adhesives are a structural protein and a transglutaminase crosslinking enzyme. We are investigating an alternative biomimetic adhesive based on gelatin and a calcium-independent microbial transglutaminase (mTG). Rheological measurements show that mTG catalyzes the conversion of gelatin solutions into hydrogels, and gel times are on the order of minutes depending on the gelatin type and concentration. Tensile static and dynamic loading of the adhesive hydrogels in bulk form demonstrated that the Young's modulus ranged from 15 to 120 kPa, and these bulk properties were comparable to those reported for hydrogels obtained from fibrin-based sealants. Lap-shear adhesion tests of porcine tissue were performed using a newly published American Society for Testing and Materials (ASTM) standard for tissue adhesives. The gelatin-mTG adhesive bound the opposing tissues together with ultimate adhesive strengths of 12-23 kPa which were significantly higher than the strength observed for fibrin sealants. Even after failure, strands of the gelatin-mTG adhesive remained attached to both of the opposing tissues. These results suggest that gelatin-mTG adhesives may offer the benefits of fibrin sealants without the need for blood products.     

Applications of biopolymers and other biotechnological products in building materials

Bio admixtures are functional molecules used in building products to optimize material properties. They include natural or modified biopolymers, biotechnological and biodegradable products. Concrete and dry-mix mortars (e.g. wall plasters or tile adhesives) represent two major applications for bio admixtures. Examples of bio products used in concrete are lignosulfonate, sodium gluconate, pine root extract, protein hydrolysates and Welan gum; and in dry-mix mortar methyl hydroxypropyl cellulose, hydroxypropyl starch, guar gum, tartaric acid, casein, succinoglycan and Xanthan gum. In a number of applications, bio admixtures compete well with synthetic admixtures. Sometimes, they are indispensable in the formulation of certain building products. Their market share is expected to increase because of technological advances, particularly in the field of microbial biopolymers, and because of the growing trend to use naturally based or biodegradable products in building materials.     

Alternate industrial feedstocks from agriculture

Before the rapid development of the petrochemical industry, many feedstocks for manufacturing paints, plastics, fibers, lubricants, adhesives, and a host of other products were derived from agriculture. Good examples are linseed, castor, tung, tall, and soybean oils; natural rubber, gums, starch and cellulose, and many sources of fiber from the plant kingdom, as well as hides, bones, and fats and oils from the animal kingdom. In addition to these traditional agricultural materials, several new plant sources have been developed through new crops research. Also, new ways have been developed for converting existing agricultural products to better chemical intermediates. Availability of farm land, economics of crop production, and competition with petroleum are such that agriculture should be considered seriously as a viable alternative for at least part of our chemical feedstock requirements.     

Impact of disinfecting nesting boards on chalkbrood control in the alfalfa leafcutting bee

The alfalfa leafcutting bee, Megachile rotundata (F.), is a solitary, cavity-nesting bee that has been managed in large numbers to pollinate alfalfa, Medicago spp., seed crops since the 1960s. Propagation of these bees from 1 yr to the next has been seriously hampered by chalkbrood, a larval disease caused by the fungus Ascosphaera aggregata Skou. In the United States, attempts to control the disease have been fairly unsuccessful, but include removing nests from the nesting boards and then disinfecting the boards with heat treatments or a fumigant. The problem is that many boards are made of polystyrene (so heat cannot be used), and very few fumigants are registered for this use. In this study, ozone was tested as a fumigant and compared with heat treatments and methyl bromide fumigation. Ozone was found to be inadequate for killing A. aggregata spores and for reducing chalkbrood levels in the field. Methyl bromide and heat treatments did greatly reduce spore viability in the boards, but did not reduce chalkbrood levels in the field. Surprisingly, larvae in new nesting boards (boards free of contamination) and chalkbrood infection levels were similar to those from nests in contaminated, used boards. Disinfecting nesting boards may be necessary for controlling chalkbrood, but the results reported here indicate that it is not sufficient in and of itself. Some other source of spores was present in the field that was greater than the effect of contamination from the boards, but the source still needs to be determined.     

A Chitosan Based,Laser Activated Thin Film Surgical Adhesive, 'SurgiLux': Preparation and Demonstration

Sutures are a 4,000 year old technology that remain the ''gold-standard'' for wound closure by virtue of their repair strength (~100 KPa). However, sutures can act as a nidus for infection and in many procedures are unable to effect wound repair or interfere with functional tissue regeneration.¹ Surgical glues and adhesives, such as those based on fibrin and cyanoacrylates, have been developed as alternatives to sutures for the repair of such wounds. However, current commercial adhesives also have significant disadvantages, ranging from viral and prion transfer and a lack of repair strength as with the fibrin glues, to tissue toxicity and a lack of biocompatibility for the cyanoacrylate based adhesives. Furthermore, currently available surgical adhesives tend to be gel-based and can have extended curing times which limit their application.² Similarly, the use of UV lasers to facilitate cross-linking mechanisms in protein-based or albumin ''solders'' can lead to DNA damage while laser tissue welding (LTW) predisposes thermal damage to tissues.³ Despite their disadvantages, adhesives and LTW have captured approximately 30% of the wound closure market reported to be in excess of US $5 billion per annum, a significant testament to the need for sutureless technology.⁴In the pursuit of sutureless technology we have utilized chitosan as a biomaterial for the development of a flexible, thin film, laser-activated surgical adhesive termed ''SurgiLux''. This novel bioadhesive uses a unique combination of biomaterials and photonics that are FDA approved and successfully used in a variety of biomedical applications and products. SurgiLux overcomes all the disadvantages associated with sutures and current surgical adhesives (see Table 1).In this presentation we report the relatively simple protocol for the fabrication of SurgiLux and demonstrate its laser activation and tissue weld strength. SurgiLux films adhere to collagenous tissue without chemical modification such as cross-linking and through irradiation using a comparatively low-powered (120 mW) infrared laser instead of UV light. Chitosan films have a natural but weak adhesive attraction to collagen (~3 KPa), laser activation of the chitosan based SurgiLux films emphasizes the strength of this adhesion through polymer chain interactions as a consequence of transient thermal expansion.⁵ Without this ''activation'' process, SurgiLux films are readily removed.^6-9 SurgiLux has been tested both in vitro and in vivo on a variety of tissues including nerve, intestine, dura mater and cornea. In all cases it demonstrated good biocompatibility and negligible thermal damage as a consequence of irradiation.^6-10     

Mutagenic action of methyl 2-cyanoacrylate vapor

Alkyl 2-cyanoacrylate adhesives were tested for mutagenicity in Salmonella typhimurium strains TA98, TA100, TA1535 and TA1538. Both a normal spot test and a spot test specially designed to test volatile compounds were used. The adhesives were also tested in the plate incorporation assay. These investigations showed that methyl 2-cyanoacrylate adhesives are mutagenic in strain TA100. The spot test for volatile compounds showed that it is the vapors from the methyl 2-cyanoacrylate monomer that are responsible for the mutagenic effect. One can conclude that working with methyl 2-cyanoacrylate adhesives entails exposure to vapors with a mutagenic effect and may therefore pose a carcinogenic hazard. Because the adhesives are used in industry, their mutagenic effect has a special importance in work environment.     

Lap Shear and Impact Testing of Ochre and Beeswax in Experimental Middle Stone Age Compound Adhesives

The production of compound adhesives using disparate ingredients is seen as some of the best evidence of advanced cognition outside of the use of symbolism. Previous field and laboratory testing of adhesives has shown the complexities involved in creating an effective Middle Stone Age glue using Acacia gum. However, it is currently unclear how efficient different adhesive recipes are, how much specific ingredients influence their performance, and how difficult it may have been for those ingredients to be combined to maximum effect. We conducted a series of laboratory-based lap shear and impact tests, following modern adhesion testing standards, to determine the efficacy of compound adhesives, with particular regard to the ingredient ratios. We tested rosin (colophony) and gum adhesives, containing additives of beeswax and ochre in varying ratios. During both lap shear and impact tests compound rosin adhesives performed better than single component rosin adhesives, and pure acacia gum was the strongest. The large difference in performance between each base adhesive and the significant changes in performance that occur due to relatively small changes in ingredient ratios lend further support to the notion that high levels of skill and knowledge were required to consistently produce the most effective adhesives.     

昆虫趋色性及诱虫色板的研究和应用进展

昆虫与植物之间色彩通讯是彼此信息交流的渠道之一,基于害虫趋色性研发的诱虫板作为一种绿色防控手段,已广泛用于农林害虫的虫情监测、预测预报、大量诱杀以及天敌诱集和指引,效果良好.本文概述了昆虫趋光趋色机理、诱虫板诱杀害虫机制和诱虫板色彩、形状、大小、高度、密度、方向、诱虫时长、植株形态和害虫生理状态等对于诱捕效果的影响,总结了诱虫板在茶园、菜地和大棚等作物环境中的多种实用技术,解析了诱虫板与昆虫性诱剂、植物源引诱剂等配合使用方法及其功效,评价了诱虫板治虫的优缺点并提出改进措施,讨论了诱虫板诱效的评价方法和成本核算.展望了新一代诱虫板研发方向、诱虫板与信息素等产品在有害生物综合治理(IPM)中的集成应用和诱虫板产业前景.     

Poly(vinyl alcohol) acetoacetate-based tissue adhesives are non-cytotoxic and non-inflammatory

Polymer-based tissue adhesives composed of poly(vinyl alcohol) acetoacetate (PVOH acac) and cross-linking amines were investigated for their effects on cell survival and inflammatory cell activation using in vitro mouse cell cultures. Cytotoxicity of tissue adhesives was evaluated by placing adhesives in direct contact with 3T3 fibroblast cells. Tissue adhesives formulated from PVOH acac and 3-aminopropyltrialkoxysilane (APS) were non-cytotoxic to fibroblasts; adhesives formulated from PVOH acac and aminated poly(vinyl alcohol) (PVOH amine) were also non-cytotoxic to fibroblasts. In contrast, a commercial adhesive composed of 2-octyl cyanoacrylate was highly cytotoxic to fibroblasts. The inflammatory potential of tissue adhesives was evaluated by exposing J774 macrophage cells to adhesives, and measuring TNF-α release from macrophages. PVOH acac-based tissue adhesives did not elicit inflammatory TNF-α release from macrophages. These results suggest that PVOH acac-based tissue adhesives are non-cytotoxic and non-inflammatory. Such tissue adhesives represent a promising technology for a variety of medical applications, including surgical wound closure and tissue engineering, and the results are also significant in the design of in vitro cell culture systems to study biomaterials.     

The versatile soybean

China’s most valuable gift to the Western World— the food of millions for centuries and an ingredient in modern adhesives, plastics, foaming solutions, spreaders, waxes, soaps, linoleum, paints and numerous other industrial products.     

Attitudes and usage of denture adhesives by complete denture wearers: a survey in Greece and the Netherlands

doi: 10.1111/j.1741‐2358.2011.00566.x
Attitudes and usage of denture adhesives by complete denture wearers: a survey in Greece and the Netherlands Objective: To explore whether there are differences in usage of and attitudes towards denture adhesives among patients in two countries. Background: There are no multi‐country surveys concerning usage of and attitudes towards denture adhesives from complete denture wearers. Materials and methods: The survey took place in Greece and the Netherlands with a sample of 284 and 165 consecutive complete denture wearers, respectively, by using a 9‐item prepared questionnaire. Statistical analysis relied on chi‐square test at α = 0.05. Results: In this survey, 26 and 20% of Greek and Dutch patients, respectively, had tried denture adhesive, but only 27% of them in Greece as well as in the Netherlands currently used it; 49% of the Greek and 45% of the Dutch participants rated the overall performance of adhesives as good. Between the two populations, no differences were identified in a majority of the research variables, except where 27% of Greeks answered that they did not know the existence of denture adhesives compared to none of the Dutch patients and when 90% of the Dutch contrary to 70% of Greeks reported that they did not need denture adhesives as they could manage their dentures well. Conclusion: The usage of and attitudes towards denture adhesives between the Greek and Dutch sample were similar with only two exceptions concerning the knowledge of existence and the need of using denture adhesives.     

Replanning and analysis of partial setup strategies in printed circuit board assembly systems

This paper considers the operation of component placement equipment for the assembly of printed circuit boards (PCBs) in a medium-volume, medium-variety manufacturing environment. It focuses on the setup management and operational planning issues associated with productive use of these expensive resources. The concept of replanning is introduced to adapt to changes in the production environment by explicitly considering the initial state of the system. The partial setup strategy is suggested as a means of efficient adaptation and as a strategy that subsumes other setup strategies encountered in practice and the literature. These concepts are applied to the optimization of a single-placement machine producing multiple products. The results of using partial setups are compared with other commonly used strategies. Experimental results suggest significant gains at the singlemachine level. Future research is being pursued to improve the solution procedures and extend these replanning concepts to the line level.     

Interactions of polysaccharide-based tissue adhesives with clinically relevant fibroblast and macrophage cell lines

The effects of polysaccharide-based tissue adhesives on cell survival and inflammatory cell activation were determined using in vitro mouse cell cultures. Cytotoxicity of tissue adhesives was evaluated by placing adhesives in direct contact with 3T3 fibroblast cells. Polysaccharide-based tissue adhesives composed of dextran aldehyde and star PEG amine were non-cytotoxic to fibroblasts; in contrast, a commercial adhesive composed of 2-octyl cyanoacrylate was highly cytotoxic to fibroblasts. The inflammatory potential of tissue adhesives was evaluated by exposing J774 macrophage cells to adhesives, and measuring TNF-α release from macrophages. Polysaccharide-based tissue adhesives did not elicit inflammatory TNF-α release from macrophages. These results suggest that polysaccharide-based tissue adhesives are non-cytotoxic and non-inflammatory; the results are therefore significant in the design of in vitro cell culture systems to study biomaterials.     

Marine adhesive proteins: natural composite thermosets

Marine environments are severely challenging for the performance and durability of synthetic adhesives. Factors commonly associated with adhesive failure are weak boundary layers (water, oxides), adhesive erosion and swelling. For many permanently attached marine organisms such as barnacles, mussels, oysters, etc., however, underwater adhesion is 'business-as-usual'. Knowledge about the chemistry and bioprocessing of these marine adhesives will provide profound insights for the evolution of a new generation of environmentally safe, water-resistant adhesives. Despite their apparent structural diversity, marine adhesives are essentially analogous to composite thermosets, that is, the adhesive consists of fibre, filler and catalyst molecules that are dispersed in a cross-linked resin rendering it resistant to heat and solvents. The fibres and fillers in these composites are variable. e.g. collagen, fibroin, chitin present as fibres, and sand, shell, air and water present as fillers. The precured resins of seven organisms including members of the Mollusca, Annelida, and Platyhelminthes have now been isolated and partially sequenced. These are proteins with basic isoelectric points, high levels of the amino acid 3,4-dihydroxyphenyl-L-alanine (DOPA), and an extended, flexible conformation. The DOPA functional group in particular is thought to play a key role in (a) the chemisorption of these polymers to surface underwater, and (b) covalent cross-linking or setting of the adhesive, the latter reaction catalysed by the enzyme catecholoxidase. Much more needs to be done to explore the details of the adhesive processing and delivery strategies used by these organisms.