The use of a triton X-100-based scintillant for counting fractions from density gradients

The properties of an aqueous scintillation mixture containing butyl-PBD as the sole scintillant and using Triton X-100 as emulsifier are described. This counting mixture, which is considerably cheaper than other published mixtures for aqueous samples, is shown to perform extremely satisfactorily with polysomes and RNA labeled by prior injection of [¹⁴C]orotic acid. When, however, this counting mixture is used with ³H-labeled samples, the density gradient solutes sucrose and cesium chloride are shown to quench the counting of RNA and polysomes but not of toluene or orotic acid.     

Liquid scintillation counting of aqueous solutions of potassium salts in a Triton X-100/toluene scintillant

The use of a toluene/Triton X-100 scintillant for counting ¹⁴C in aqueous solutions of potassium salts including potassium hydroxide has been investigated. Suitable conditions for the counting of CO₂ entrapped in potassium hydroxide are described. Quench correction by automatic external standard channels ratio procedures has been found to be of value with optimised conditions of counting.     

A note on two liquid scintillation fluors useful for primary production work

Summary Two liquid scintillation fluors, the first using a 2-methoxyethanol/toluene solvent, the second a Triton X-100/toluene solvent, are discussed. Data presented indicate that the technique using the 2-methoxyethanol/toluene solvent produces higher d.p.m. than does solid support counting. The Triton X-100/toluene solvent fluor is suggested for measuring aqueous samples such as algal excretion products and ¹⁴C stock solutions.     

Tritosol: A new scintillation cocktail based on Triton X-100

A scintillation cocktail consisting of 3.0 g PPO, 257 ml Triton X-100, 106 ml ethanol, 37 ml ethylene glycol, and 600 ml xylene is described. A linear relationship between counting efficiency and the external standard ratio could be demonstrated over a wide range of quenching. The counting efficiencies (unquenched) for³H are about 47%, for¹⁴C about 87%, and for⁴⁵Ca about 80%.     

An improved scintillation cocktail of high-solubilizing power

A scintillation cocktail containing 25% Triton X-114 in xylene is considered for a broad range of scintillation counting applications. The cocktail gives good counting efficiencies for ³H (47%) and ¹⁴C (93%). It will accept up to 30% (v/v) aqueous sample. The scintillation fluid is also used effectively with samples which are difficult to solubilize, such as the degradation products from the solubilization of polyacrylamide gels. The cocktail can be formulated for less than $2.00 per gallon.     

Liquid scintillation counting of aqueous samples using Triton-containing scintillants

Markedly unstable count rates were observed using a toluene-Triton (2:1, $\text{v}\text{v}$) scintillant during counting of water-soluble radioactive compounds when < 5% ($\text{v}\text{v}$) water was present, because of the separation of phases. Efficiency correction in these instances could not be made by using ³H₂O as internal standard, because under the same conditions count rates with tritiated water were stable. Increasing water to ≥6% stabilized the count rates. With toluene-Triton (2:1, $\text{v}\text{v}$) scintillant, the water level should preferably be maintained between either 6 and 12 or 18 and 24% for ¹⁴C- and ³H-labeled compounds for counting at 6°C or at ambient temperature (but only between 6 and 12% for ³H counting at room temperature). With a “Tritosol” (Anal. Biochem.63, 555 (1975) modified to contain 35 ml of ethylene glycol, 140 ml of ethanol, 250 ml of Triton X-100, 575 ml of xylene, 3 g of PPO, and ±200 mg of POPOP, water levels of up to 23% were acceptable for ¹⁴C and ³H for counting at room temperature or at 6°C. Within these limitations, with the toluene-Triton or with the modified Tritosol as scintillant, both polar and apolar radioactive compounds exhibited similar efficiencies and gave quench-correction curves, based on the external standard ratio, that were linear for both ¹⁴C and ³H-labeled compounds.     

A simple method for the liquid scintillation counting of precipitated protein from red blood cells

A method for the liquid scintillation counting of precipitated protein from red cells in 0.1–1.0 ml of blood is described. Precipitate is incubated for 0.5 hr at 100°C with equal volumes of acetic acid, ethyl acetate, and hydrogen peroxide; an equal volume of hydrochlorie acid is then added, followed by a toluene/Triton X-100 scintillation mixture containing primary and secondary scintillators. Maximum counting efficiencies with precipitate from 0.2 ml of blood were 90% for ¹⁴C and 35% for ³H. Recovery of labeled amino acid was not less than 90%. Chemiluminescence decayed to not more than 15 cpm above background in 45 min.     

An improved technique for measuring assimilation efficiency by the 51Cr−14C twin tracer method

Summary Calow and Fletcher have shown that assimilation efficiency can be calculated from the ratios of an assimilated radiotracer (e.g. ¹⁴C) and a non-assimilated tracer (e.g. ⁵¹Cr) in the food and faeces of freshwater pulmonates [Oecologia (Berl.) 9, 155–170 (1972)]. It is suggested that their counting methods have limitations and are not wholly suitable for wide biological application. An alternative technique was tested using third instar larvae of a Kenyan cetoniid, Pachnoda ephippiata (Gerst.) (Coleoptera, Scarabaeidae), fed on an artificial food medium labelled with ¹⁴C-glucose and ⁵¹CrCl₃. The activity of both tracers in food and faeces was estimated from simultaneous counts of the emissions recorded by a liquid scintillation spectrometer. The scintillant solution, toluene—Triton X-100—PPO, extracted virtually all of the labelled tracers from 0.2 g samples of the agar-cellulose-water food medium. The calculated assimilation efficiency values for glucose increased from 50.2% to 78.6% over the 6 days following exposure to the labelled food. 90.8% of the total ⁵¹Cr recovered was egested during these 6 days, 76.8% during the first 3. An ecologically more meaningful estimate of assimilation efficiency was calculated by integrating the ¹⁴C and ⁵¹Cr counts over the 15 days that faeces were collected. The applications of this approach to measuring assimilation efficiency are wide. They include the possibility of measuring how much excreta are produced from a given amount of Ingesta and of determining the role of gut-microorganisms in the assimilation of their host's food.     

Agarose-DTNB column for binding sulfhydryl-containing proteins and peptides.

The counting rate of [1-¹⁴C]trichloroacetic acid (TCA) was not stable in a standard toluene/Triton X-100 liquid scintillation solution because this compound becomes partially degraded to ¹⁴CO₂ and CHCl₃. Both toluene and Triton were contributing factors in causing this degradation. The NCS solubilizer added to the toluene/Triton scintillation solution trapped ¹⁴CO₂ and stabilized counting rates of [1-¹⁴C]TCA. When [2-¹⁴C]TCA was used, ¹⁴CHCl₃ remained in the scintillation solution resulting in stable counting rates without the addition of NCS.     

Molecular Forms of Acetylcholinesterase in Bovine Caudate Nucleus and Superior Cervical Ganglion: Solubility Properties and Hydrophobic Character

Abstract: In the present paper, we report an analysis of acetylcholinesterase molecular forms in the bovine caudate nucleus and superior cervical ganglion. We show that: (1) The superior cervical ganglion contains a significant proportion (～ 15%) of collagen-tailed forms (mostly A₁₂ and A₈), but these molecules are found only as traces (ca. 0.002%) in the caudate nucleus, even in favorable extraction conditions (i.e., in the presence of 1 m -NaCl, 5 mm -EDTA, 1% Triton X-100). (2) The bulk of acetylcholinesterase corresponds to globular forms, mostly the tetrameric G₄ and the monomeric G₁ forms, with a smaller proportion of the dimeric G₂ form. (3) The tetrameric enzyme exists as a minor soluble component (G^S₄) that does not interact with Triton X-100, and a major hydrophobic component (G^H₄) that is partially solubilized in the absence of detergent in the caudate nucleus, but not in the superior cervical ganglion. (4) The monomeric G₁ form presents a marked hydrophobic character, as indicated by its interaction with Triton X-100, although it may be solubilized in large part in the absence of detergent in both tissues. (5) The detergentsolubilized forms aggregate upon removal of detergent. This property disappears after partial purification of G₄) that does not interact with Triton X-100, and a major hydrophobic component (G^H₄, but is restored upon addition of an inactivated crude extract, indicating that it is attributable to interactions with other hydrophobic components. (6) The proportions of molecular forms solubilized in detergent-free buffers vary with the ionic composition of the medium. Repeated extractions of caudate nucleus in Tris-HCl buffer produce a larger overall yield of G₁ form (e.g., 40%) than appears in a single quantitative detergent solubilization (<15%). This G₁ form apparently derives in part from a pool of G^H₄ form. (7) However, detergents that allow a quantitative solubilization of acetylcholinesterase yield the same proportions of forms (about 85% G₄) independently of the ionic conditions. (8) Modifications of the molecular forms occur spontaneously during purification, or storage of the crude aqueous ex-tracts, in a manner that depends on the ionic conditions. In Tris-HCl buffer, G₁ is converted into a well-defined 7.5S form. In Ringer, polydisperse components are formed. The effects observed in Ringer cannot be reproduced by addition of 5 mm -Ca_2- to the Tris buffer either during or after extraction. (9) Proteases, such as pronase, convert the hydrophobic forms into molecules that do not appear to interact with Triton X-100, and do not aggregate in its absence. These results raise fundamental questions regarding the status of acetylcholinesterase in situ, the structure and interactions of its molecular forms. They are discussed with reference to previous publications.     

Irreversible inactivation of the membrane-bound enzyme IIlac of the lactose phosphotransferase system of Staphylococcus aureus by triton X-100 and protection by substrates

Enzyme II^lac, the membrane-bound component of the lactose phosphotransferase system of Staphylococcus aureus, catalyzes the phosphorylation-transport reaction below:

(The sugar can be lactose or one of its analogs.) The effects of the non-ionic detergents Triton X-100, Brij 35, and Tween 40 on the activity of Enzyme II^lac were studied. Especially striking effects were observed using Triton X-100, a detergent previously used to solubilize and isolate this enzyme. A systematic study of Triton effects over a range of concentrations and temperatures demonstrated three aspects of Triton-membrane interaction. At 0.1% Triton and 25° C Enzyme II^lac is activated, but remains particulate. At 0.5% Triton and 25° C, it is almost completely solubilized, with good retention of activity. At 0.5% Triton and 37° C, it is rapidly and irreversibly inactivated. Sugar substrates and inhibitory sugar analogs protect Enzyme II^lac against inactivation; the effect is specific for β-galactosides. The other substrates of Enzyme II^lac, phospho-Factor III^lac, does not affect Triton inactivation, and the product analog galactose 6-phosphate slightly enhances the inactivation rate.     

DNA synthetic activity of nuclei isolated from differentiating cardiac muscle and association of DNA polymerase alpha with the outer nuclear membrane

[³H]dTMP incorporation into DNA of nuclei isolated from differentiating cardiac muscle of the rat has been characterized. Nuclei prepared at different times during the terminal phase of differentiation by a procedure not involving a detergent (Triton X-100) wash show a progressively diminished capacity to support in vitro [³H]dTMP incorporation; this diminution parallels the loss of DNA polymerase α from cardiac muscle. The rate of incorporation of [³H]dTMP into DNA of nuclei washed twice with 0.5% Triton X-100 does not correlate with the in vivo DNA synthetic activity. As determined by electron microscopy the Triton X-100 wash removes the outer nuclear membrane; the pellet obtained by centrifuging the Triton X-100 extract of these nuclei consists of circular membrane vesicles. The predominant DNA polymerase activity in these preparations was characterized using pH optimum, N-ethylmaleimide sensitivity, and correlation to in vivo DNA synthetic activity as criteria. DNA polymerase α activity predominated in the non-Triton X-100-extracted nuclei and in the outer nuclear membrane fraction; DNA polymerase β activity was the predominant activity observed in Triton X-100-extracted nuclei. These data emphasize that the procedure which is used to isolate nuclei from proliferating cells can greatly influence the nature of the DNA synthetic activity that is observed in vitro, suggest that DNA polymerase α is associated with the outer nuclear membrane, and add support to the idea that this enzyme is involved in eukaryotic DNA replication.     

Liquid scintillation counting of polyacrylamide gels crosslinked with N,N′-methylene-bis-acrylamide and N,N′-diallyltartardiamide

Tritium (³H)-labeled material within polyacrylamide gel slices is commonly quantified by four general liquid scintillation counting methods: combustion, gel solubilization, selective solubilization of modified crosslinked gels, and elution. Of these four methods examined in this study, only combustion ensured complete recovery of ³H label; however, a less expensive and more convenient elution method yielding both a high recovery and cocktail counting efficiency was the use of Soluene-350 with 0.55% Permablend III in toluene. This particular solubilizer-cocktail system eliminates almost all chemiluminescence as does combustion.     

The Non-Ionic Detergent Brij 58 Conserves the Structure of the Tonoplast H+-ATPase of Mesembryanthemum crystallinum L. During Solubilization and Partial Purification

The effects of solubilization with Triton X-100 or Brij 58 on the polypeptide composition and the substrate affinity of the tonoplast H⁺-ATPase of plants of Mesembryanthemum crystallinum performing C₃ photosynthesis or crassulacean acid metabolism (CAM) have been compared. Although all known subunits of the tonoplast H⁺-ATPase were present in the fraction of solubilized proteins after treatment with Brij 58 or Triton X-100, with Triton X-100 the apparent K_M value for ATP hydrolysis was increased by a factor of 1.8 and 1.5 in preparations from C₃ and CAM plants, respectively, even at low concentrations in contrast to treatment with Brij 58. This is explained by structural changes of the tonoplast H⁺-ATPase due to the Triton X-100 treatment. After solubilization with Brij 58 the tonoplast H⁺-ATPase was partially purified by Superose-6 size-exclusion FPLC. When Brij 58 was present, addition of lipids to the chromatography buffer was not necessary to conserve enzyme activity in contrast to previously described purification methods using Triton X-100. The substrate affinity of the partial purified H⁺-ATPase was similar to the substrate affinity obtained for ATP-hydrolysis of native tonoplast vesicles, indicating that the enzyme structure during partial purification was conserved by using Brij 58. The results underline that the lipid environment of the tonoplast H⁺-ATPase is important for enzyme structure and function.     

Characteristics of phospholipase D in reverse micelles of Triton X-100 and phosphatidylcholine in diethyl ether

Summary Phospholipase D, from cabbage, is active in reverse micelles formed from its substrate phosphatidylcholine and Triton X-100 in diethyl ether. The activity is optimum at w₀=12.5. The increase of the molar ratio of Triton X-100/substrate from 1:4 to 2:1 results in an activity decrease by 25 %. At 136 mM Triton X-100 the K_M value in reverse micelles is 136 mM, whereas it is 0.40 mM in the aqueous system containing SDS.     

The effects of cations on the structure and photochemistry of the photosystem II core complex

We have studied the effects of cations and detergents on the structure (molecular weight) and photochemistry of Triton X-100 Photosystem II subchloroplast particles (TSF-IIa). The effect of Mg²⁺ ions on activity depended on the Triton X-100 content of the preparation. If the residual Triton X-100 was not removed prior to assay, MgCl₂ increased the rate of electron transport, acting at a site on the reducing side of Photosystem II. Lowering the pH also increased the rate of electron transport. If the Triton X-100 was removed from the particles, both MgCl₂ and NaCl caused a decrease in the rate of electron transport. Addition of Triton X-100 caused a reversible decrease in the number of active Photosystem II reaction centers. Both cations and Triton X-100 had a profound effect on the molecular weight of the Photosystem II particles as determined by gel filtration. At 20 °C, addition of 0.05% Triton X-100 decreased the molecular weight from a high value (≥800,000) to 250,000. At 4 °C, addition of 1 mm MgCl₂ or 100 mm NaCl increased the molecular weight of the complex. In the absence of these salts 67% of the protein eluted with a molecular weight of 460,000 (the rest was >800,000-in the void volume). In the presence of these salts all of the material had a molecular weight of ≥800,000. A similar effect was observed when the pH was lowered from 8 to 6. Further work is needed to determine whether there is a correlation between the changes in molecular weight and activity.     

Simultaneous phenanthrene and cadmium removal from contaminated soil by a ligand/biosurfactant solution

Surfactants and inorganic ligands are pointed as efficient to simultaneous removal of heavy metals and hydrophobic organic pollutants from soil. However, the biosurfactants are potentially less toxic to soil organisms than other chemical agents. Thus, in this study the efficiency of combinations of iodide (I⁻) ligand and surfactants produced by different bacterial species in the simultaneous removal of cadmium (Cd²⁺) and phenanthrene in a Haplustox soil sample was investigated. Four microbial surfactants and the synthetic surfactant Triton X-100 were tested with different concentrations of ligand. Soil samples contaminated with Cd²⁺ and phenanthrene underwent consecutive washings with a surfactant/ligand solution. The removal of Cd²⁺ increased with increased ligand concentration, particularly in solutions containing biosurfactants produced by the bacterial strains Bacillus subtilis LBBMA155 (lipopeptide) and Flavobacterium sp. LBBMA168 (mixture of flavolipids) and Triton X-100. Maximum Cd²⁺ removal efficiency was 99.2% for biosurfactant produced by Arthrobacter oxydans LBBMA 201 (lipopeptide) and 99.2% for biosurfactant produced by Bacillus sp. LBBMA111A (mixed lipopeptide) in the presence of 0.336 mol iodide l⁻¹, while the maximum efficiency of Triton X-100 removal was 65.0%. The biosurfactant solutions removed from 80 to 88.0% of phenanthrene in soil, and the removal was not influenced by the presence of the ligand. Triton X-100 removed from 73 to 88% of the phenanthrene and, differently from the biosurfactants, iodide influenced the removal efficiency. The results indicate that the use of a single washing agent, called surfactant-ligand, affords simultaneous removal of organic contaminants and heavy metals.     

Semliki Forest virus membrane proteins, preparation and characterization of spike complexes soluble in detergent-free medium

After Triton X-100 delipidation and subsequent Triton X-100 removal in a sucrose gradient the membrane protein spikes of Semliki Forest virus remained soluble in aqueous buffers. It was shown they were present as octameric complexes with a molecular weight of 95 · 10⁴ and that they contain less than 4% lipid and detergent by weight. In electron microscopy after negative staining they appeared as “rosette”-shaped particles. Part of the protein could also be found associated in ordered paracrystalline arrays.     

Phospholipid requirement of microsomal chitinase fromMucor mucedo

Microsomal and supernatant chitinase activities have been prepared from mycelial cultures ofMucor mucedo. Studies of their responses to changing temperature and phospholipid composition indicate that the lipid environment is important in regulating membrane-bound chitinase activity, but that supernatant chitinase activity does not have a phospholipid requirement. Membrane-bound chitinase was solubilized by different types of non-denaturing detergents. Maximum solubilization was achieved with 1 mM Zwittergent-14 or 1.2% Triton X-100 (93% and 90% solubilization, respectively). This solubilized chitinase activity could not be activated by protease treatment, i.e., was nonzymogenic, as was the supernatant chitinase. The insoluble residual chitinase activity was, however, zymogenic after treatment with 1.2% Triton X-100, but fully active after treatment with 3% Triton X-100.     

A comparative study of the effect of various detergents on the structure and function of sarcoplasmic reticulum vesicles

Summary The effects produced by the detergents Triton X-100, sodium dodecylsulphate and sodium cholate on sarcoplasmic reticulum vesicles have been comparatively studied. In all cases, maximal effects are found 5 min after detergent addition. Triton X-100 and SDS are approximately ten times more effective than cholate in protein and phospholipid solubilization. Both Triton X-100 and SDS maintain Ca⁺⁺ accumulation in SR vesicles at detergent concentrations below 10^–3 M; higher concentrations cause a strong inhibition. On the other hand, cholate produces a gradual inhibition of Ca⁺⁺ accumulation in the concentration range between 10^–4 M and 2.5 × 10^–2 M. Triton X-100 and SDS produce a gradual solubilization of the specific Ca⁺⁺-ATPase activity up to a 10^–3 M detergent concentration, above which a strong inactivation occurs, while the enzyme solubilization increases with the presence of cholate in the whole concentration range under study. The different behaviour of sodium cholate, when compared to SDS or Triton X-100, is discussed in relation to the surfactant molecular structures. The possibility of membrane lysis and reassembly in the presence of some detergents is also considered.Abbreviations SR sarcoplasmic reticulum - SDS sodium dodecylsulphate - DTT dithiothreitol - EGTA ethyleneglycoltetraacetate - PEP phosphoenolpyruvate