Methods for MAG3 conjugation and 99mTc radiolabeling of biomolecules

The chelator mercaptoacetyltriglycine (MAG3) forms a single stable chelate with technetium-99m (99mTc) oxotechnetate. The bifunctional N-hydroxysuccinimidyl ester of mercaptoacetyltriglycine with S-acetyl protection of the sulfhydryl group may be used to conjugate MAG3 to primary amine functionalized biomolecules for the purpose of radiolabeling with 99mTc for gamma detection or single photon emission computed tomography imaging (SPECT). We report here an improved MAG3 conjugation and 99mTc radiolabeling method capable of generating high radiochemical yield and high specific radioactivity. Post-labeling purification will not be needed if the protocol is followed as presented. Apart from the preparation of reagents, the conjugation and purification requires about 4 h, while the labeling with 99mTc requires about an additional 30 min.     

Improving the labeling of S-acetyl NHS-MAG(3)-conjugated morpholino oligomers

S-Acetyl MAG(3) (S-acetylmercaptoacetyltriglycine) has been used as a chelator for the (99m)Tc labeling of a variety of biomolecules. The objective of this study was to improve upon the labeling of morpholino (MORF), a DNA analogue, as a model biomolecule. A 15mer MORF with a primary amine was conjugated with NHS-MAG(3) in the usual manner, and the MORF-MAG(3) was purified over a P4 column as before. The conjugate was radiolabeled using stannous ion as usual, and the impurities were identified using size exclusion high-performance liquid chromatography (SE HPLC). Various methods were then investigated to remove the impurities. With tartrate as the transchelator, two impurities were identified as labeled MAG(3) and labeled tartrate. The labeled MAG(3) could not be removed by simply repurifying the conjugate using the usual pH 5.2 NH(4)OAc buffer before labeling. However, this impurity could be completely removed if the conjugate was adjusted to pH 7.6 and heated before repurification. The labeled tartrate impurity was removed by heating during labeling. On the basis of these observations, the following procedure for purification of the conjugation mixture and subsequent labeling was adopted. After MORF was conjugated with NHS-MAG(3) and purified over P4 with pH 5.2 NH(4)OAc eluant, the oligomer fractions were combined, adjusted to pH 7.6, and heated in a boiling water bath for 20 min. The conjugated oligomer was then repurified over P4 for storage at refrigerator temperatures. Labeling is achieved simply by adding fresh stannous ion to a solution of the MORF-MAG(3) in pH 7.6 containing tartrate followed by (99m)Tc-pertechnetate. After the mixture is heated for 20 min in boiling water, the labeling efficiency is always over 90% as determined by size exclusion HPLC and paper chromatography and the specific activities can exceed 7 mCi/microg. By making several relatively simple changes to the routine procedure used to conjugate and radiolabel biomolecules with (99m)Tc via MAG(3), a modified procedure was developed that results in labeling efficiency high enough to avoid postlabeling purification.     

DOTA derivatives for site-specific biomolecule-modification via click chemistry: synthesis and comparison of reaction characteristics

Due to the high stability of its complexes with many M(2+) and M(3+)-ions, DOTA (1,4,7,10-tetraazacyclododecane-N,N',N″,N?-tetraacetic acid) is the most commonly used chelator for the derivatization and radiolabeling of bioactive molecules. Most of the currently used DOTA derivatives comprise amine-reactive functionalities, limiting their application to the derivatization of fully protected molecules or otherwise resulting in randomly distributed conjugation sites of undefined number. Click chemistry reactions are a valuable alternative to this unspecific conjugation as they proceed efficiently and chemoselectively under mild conditions allowing a site-specific derivatization of unprotected biomolecules. In this work, we describe straightforward syntheses of DOTA derivatives containing thiol, maleimide, aminooxy, aldehyde, alkyne, and azide functionalities, amenable to the currently most often used click chemistry reactions. Furthermore, the efficiency of the respective click reactions introducing DOTA into bioactive molecules was investigated. For each of the synthesized DOTA synthons, the site-specific and efficient conjugation to Tyr(3)-octreotate could be shown. Among these, the addition and oxime formation reactions proceeded fast and without side reactions, giving the products in high yields of 64-83% after purification. The copper-catalyzed triazole formation reactions produced some side-products, giving the desired products in lower, but still reasonable overall yields of 19-25%. All synthesized peptide-DOTA-conjugates were labeled with (68)Ga in high radiochemical yields of 96-99% and high specific activities providing compounds of high purity, demonstrating the applicability of all synthons for biomolecule modification and subsequent radiolabeling.     

Preparation and properties of 99mTc(CO)3+-labeled N,N-bis(2-pyridylmethyl)-4-aminobutyric acid

Labeling biomolecules with (99m)Tc(CO)(3)(+) ((99m)Tc tricarbonyl) is attracting increasing attention. Although histidine is often considered an ideal bifunctional chelator for (99m)Tc (or (188)Re) tricarbonyl, the family of dipicolylamine carboxylate chelators may be a useful alternative because of the expected ease of synthesis and because the structure provides a pendent carboxylate for potential conjugation to biomolecules. The dipicolylamine chelator N,N-bis(2-pyridylmethyl)-4-aminobutyric acid (BPABA) was synthesized using 4-aminobutyric acid in place of glycine or aminopropionic acid in the literature, to avoid possible involvement of the carboxylate in the complex formation process by forming five- or six-membered chelation rings. Using a commercial tricarbonyl kit (Mallinckrodt), the complex formation properties of both BPABA and commercial histidine with (99m)Tc tricarbonyl were investigated, and the in vitro complex stabilities in saline and in serum were compared. Stability in vivo was also examined following i.v. administration to normal mice. BPABA was synthesized simply and quantitatively by reacting picolyl chloride with aminobutyric acid in one step. On RP HPLC, the product eluted essentially in one peak and the structure was confirmed by ESI-MS. After labeling, both BPABA and histidine were shown by RP HPLC to form tricarbonyl complexes. In both cases, after incubation at 100 degrees C for 20 min, only one predominant peak of (99m)Tc(CO)(3)(+)-histidine or (99m)Tc(CO)(3)(+)-BPABA was apparent, and both complexes were stable at room temperature in saline for at least 24 h. After incubation for 24 h in 37 degrees C serum, by SE HPLC, 20% of the (99m)Tc(CO)(3)(+)-histidine was bound to serum protein compared to less than 10% for (99m)Tc(CO)(3)(+)-BPABA. A 5000 molar excess of histidine at 100 degrees C for 6 h was unable to dissociate (99m)Tc(CO)(3)(+)-BPABA. By contrast, BPABA easily dissociated (99m)Tc(CO)(3)(+)-histidine under the same conditions. Both complexes were stable in vivo in mice, and (99m)Tc(CO)(3)(+)-BPABA showed rapid and specific hepatobiliary clearance while (99m)Tc(CO)(3)(+)-histidine was cleared through the kidneys. In conclusion, BPABA was easily synthesized and was shown to possess properties comparable to histidine for labeling of biomolecules with (99m)Tc tricarbonyl. However, it was found that the chelator concentration required for quantitative (99m)Tc tricarbonyl labeling with both BPABA and histidine were 2 orders higher than that required with more conventional labeling using MAG(3). Finally, the complex (99m)Tc(CO)(3)(+)-BPABA itself was found to clear exclusively via the hepatobiliary pathway and may have value as a potential hepatobiliary imaging agent.     

Conjugation of DOTA-like chelating agents to peptides and radiolabeling with trivalent metallic isotopes

Peptides can be labeled with various trivalent radiometals for imaging or targeted radionuclide-therapy applications. The peptide is first conjugated to a chelating agent that is able to form stable complexes with the radionuclide of interest. This conjugation step can be carried out as part of the solid-phase peptide synthesis, or it can be undertaken in the solution phase after synthesis and purification of the peptide. The latter route, described here, involves reacting a molar excess of the activated tri-tert-butyl ester-derivatized chelator with a designated free amino group of a peptide analog, in which all other reactive amines are protected, in the presence of a coupling agent. The conjugate molecule is then purified prior to deprotection and further purification by HPLC. The product can be radiolabeled by addition of a suitable metal salt, followed, if necessary, by removal of the unchelated metal. The entire process of conjugation, purification and radiolabeling should take approximately 12.5 h.     

"Click-to-chelate": in vitro and in vivo comparison of a 99mTc(CO)3-labeled N(tau)-histidine folate derivative with its isostructural, clicked 1,2,3-triazole analogue

A side-by-side comparison of the synthesis, radiolabeling, and in vitro and in vivo characterization of two new and isostructural (99m)Tc-tricarbonyl folic acid radiotracers comprising either a N(tau)-functionalized histidine (His) chelator or a 1,4-bifunctionalized 1,2,3-triazole His analogue is described. The 1,2,3-triazole-containing folic acid derivative was synthesized in approximately 80% yield by a short reaction sequence including application of click chemistry (the Cu(I)-catalyzed cycloaddition of azides and terminal alkynes). The synthesis of the ligand system and the functionalization of the folic acid derivative were accomplished simultaneously, which prompted us to call this approach "click-to-chelate". In comparison, the reported regioselective synthesis of the N(tau)-His compound provided the final product in only very low yields (<1%). While the efficiency of the syntheses differs considerably, the two isostructural folate derivatives exhibit virtually identical properties with respect to Tc-99m radiolabeling and in vitro and in vivo characteristics as shown by experiments performed with FR-positive KB cells and xenografted mice bearing folate receptor overexpressing tumors. We have demonstrated herein for the first time that a ligand system known to be an excellent chelator for the stable complexation of the organometallic core [M(CO)3] (+) (M = Tc-99m, Re) can be replaced by an isostructural 1,2,3-triazole analogue without influencing the characteristics of the radiometal conjugate. The "click-to-chelate" strategy provides a highly efficient and convenient entry to metal conjugates suitable for diagnostic and potentially therapeutic applications. The described procedures should be readily applicable to any azide-functionalized (bio)molecule and, thus, are likely to represent the method of choice for the future development of radiopharmaceuticals radiolabeled with the organometallic precursors [M(CO)3(H2O)3] (+) (M = (99m)Tc, (188)Re).     

Synthesis and properties of a nonhydrolyzable adenosine phosphosulfate analog

Initial activation of inorganic sulfate for subsequent synthesis of sulfated biomolecules requires the action of ATP-sulfurylase to generate adenosine 5'-phosphosulfate (APS). This activated sulfate intermediate is both chemically labile and susceptible to enzymatic degradation. Consequently, it has not proven useful as a ligand for either purification or characterization of the various APS-utilizing enzymes. For these purposes, a stable analog of APS was required. This paper describes the simple and efficient synthesis and structural confirmation of a nonhydrolyzable APS analog, beta-methylene APS, with an overall molar yield of 40-50%. The method involves nucleophilic substitution of the chlorine moiety of a 5'-chloromethylphosphonate ester of 2',3'-O-isopropylidene adenosine by a sulfite ion. We also report the initial utilization of this compound as an inhibitor in kinetic trials of both ATP-sulfurylase and APS kinase and as an affinity ligand for the purification of these two APS-utilizing enzymes from cartilaginous tissue.     

Rapid and simple one-step F-18 labeling of peptides

Labeling biomolecules with 1?F is usually done through coupling with prosthetic groups, which requires several time-consuming radiosynthesis steps and therefore in low labeling yield. In this study, we designed a simple one-step 1?F-labeling strategy to replace the conventional complex and the long process of multiple-step radiolabeling procedure. Both monomeric and dimeric cyclic RGD peptides were modified to contain 4-NO?-3-CF? arene as precursors for direct 1?F labeling. Binding of the two functionalized peptides to integrin α(v)β? was tested in vitro using the MDA-MB-435 human breast cell line. The most promising functionalized peptide, the dimeric cyclic RGD, was further evaluated in vivo in an orthotopic MDA-MB-435 tumor xenograft model. The use of relatively low amount of precursor (~0.5 μmol) gave reasonable yield, ranging from 7 to 23% (decay corrected, calculated from the start of synthesis) after HPLC purification. Overall reaction time was 40 min, and the specific activity of the labeled peptide was high. Modification of RGD peptides did not significantly change the biological binding affinities of the modified peptides. Small animal PET and biodistribution studies revealed integrin specific tumor uptake and favorable biokinetics. We have developed a novel one-step 1?F radiolabeling strategy for peptides that contain a specific arene group, which shortens reaction time and labor significantly, requires low amount of precursor, and results in specific activity of 79 ± 13 GBq/μmol. Successful introduction of 4-fluoro-3-trifluoromethylbenzamide into RGD peptides may be a general strategy applicable to other biologically active peptides and proteins.     

Chemical modification to reduce renal uptake of disulfide-bonded variable region fragment of anti-Tac monoclonal antibody labeled with 99mTc.

The anti-Tac disulfide-bonded variable region fragment (dsFv) is a genetically engineered, 25 kDa, murine monoclonal antibody fragment that recognizes the alpha subunit of the interleukin-2 receptor (IL-2Ralpha). The dsFv radiolabeled with the tetrafluorophenyl ester (TFP) of [99mTc]mercaptoacetyltriglycine ([99mTc]MAG3-TFP) showed rapid tumor uptake and fast blood clearance in mice, resulting in high tumor-to-nontumor background ratios. However, its high renal uptake was a problem. In this study, we tested the effect of lowering the isoelectric point (pI) of dsFv to <9.3 on renal and tumor uptake. To lower the pI, dsFv was acylated simultaneously with both [99mTc]MAG3-TFP and TFP-glycolate. The acylation of dsFv decreased its pI and its immunoreactivity inversely proportional to the molar ratio of TFP-glycolate to dsFv, whereas the conjugation of [99mTc]MAG3-TFP alone did not. When biodistribution studies were performed in nude mice, the effect of the lowered pI was reflected primarily in decreased kidney uptake and whole-body retention, with its highest effect seen at the earliest time point (15 min) after injection. In tumor-bearing nude mice, glycolated [99mTc]MAG3-dsFv with a pI range of 4.9 to 6.5 accumulated selectively into IL-2 receptor-positive SP2/Tac tumor similar to that of the control [125I]dsFv labeled by the Iodo-Gen method, whereas its renal uptake was 25% of [125I]dsFv at 15 min. At 90 min, the ratios of tumor to receptor-negative SP2/0 tumor, liver, kidney, stomach, and blood had peaked at 10.9, 8.5, 0.3, 5.0, and 6.2, respectively, for the glycolated [99mTc]MAG3-dsFv. The corresponding ratios for [125I]dsFv were 3.7, 5.0, 0.1, 1.5, and 2.1, respectively.     

A trithiolate tripodal bifunctional ligand for the radiolabeling of peptides with gallium(III)

A tripodal bifunctional chelator for gallium has been prepared with a chelation core consisting of three thiols and a tertiary amine. The synthesis proceeds in 13 steps with an overall yield of 22%. An aromatic amine is available for conjugation to peptides through carbodiimide coupling. Gallium(III) complexes were readily prepared from both the bifunctional chelator and a phenylalanine-conjugated system. These complexes underwent stability evaluation and were found to be stable to ligand exchange and enzymatic hydrolysis. This bifunctional chelator appears to be suitable for conjugation to peptides for the preparation of gallium radiopharmaceuticals.     

An improved synthesis of a key intermediate for (+)-biotin from D-mannose

An efficient and reproducible process for the synthesis of methyl 2,3,4,5-tetradeoxy-7,8-O-isopropylidene-D-arabino-nanonate (2), a key intermediate in the total synthesis of (+)-biotin (1), starting from readily available D-mannose is described. The crucial part of this synthesis was the development of a practical route to a novel O-benzyl protected unsaturated ester methyl (benzyl 5,6,7,8-tetradeoxy-2,3-O-isopropylidene-alpha-D-lyxo-nona-5,7-dienofuranosid) uronate (7), allowing the one-step preparation of hydroxy ester methyl 5,6,7,8-tetradeoxy-2,3-O-isopropylidene-alpha-D-lyxo-nanofuranuronate (8) by the catalytic debenzylation and hydrogenation over palladium on carbon catalyst. This procedure requires no chromatographic purification, which makes it ideal for synthetic preparation on an industrial scale.     

De novo synthesis of a new diethylenetriaminepentaacetic acid (DTPA) bifunctional chelating agent

Diethylene triamine pentaacetic acid (DTPA) has been in extensive use as a metal chelator in the development of radiopharmaceuticals and contrast agents. The former application uses DTPA mostly as a bifunctional chelating agent (BCA) conjugated to tumor-targeting vehicles (TTVs) such as monoclonal antibodies (MAbs) and receptor-directed peptides. A new bifunctional DTPA derivative was synthesized by a fully organic scheme. This compound, N(4),N(alpha),N(alpha),N(epsilon),N(epsilon)-[pentakis(carboxymethyl)]-N(4)-(carboxymethyl)-2,6-diamino-4-azahexanoic hydrazide (20) was prepared by a convergent synthesis strategy using N(alpha)-benzyloxycarbonyl-2,3-diaminopropionic acid as the starting compound. This commercially available material was used to build a functionalized triamine which served as the molecular core template for assembling the target molecule. To evaluate the conjugation and radiolabeling capabilities of this new molecule, it was covalently attached to the anti-TAG-72 MAb, Delta CH2HuCC49, and the conjugate was radiolabeled in near-quantitative yields with yttrium-90 ((90)Y) and lutetium-177 ((177)Lu). Biodistribution of the (177)Lu-labeled DTPA-Delta CH2HuCC49 in tumor-bearing nude mice demonstrated preservation of the immunoreactivity of the MAb as indicated by high tumor uptake. In addition to the introduction of a new bifunctional DTPA, this work reports on a novel synthetic approach for preparation of this useful metal chelator and introduces a new conjugation protocol.     

Production of [F-18]fluoroannexin for imaging apoptosis with PET

Recombinant human-annexin-V was conjugated with 4-[F-18]fluorobenzoic acid (FBA) via its reaction with the N-hydroxysuccinimidyl ester (FBA-OSu) at pH 8.5. A series of reactions using varying amounts of annexin-V, unlabeled FBA-OSu, and time produced products with different conjugation levels. Products were characterized by mass spectrometry and a cell-binding assay to assess the effect of conjugation. In each case, the conjugated protein was a mixture of proteins with a range of conjugation. Annexin-V could be conjugated with an average of two FBA mole equivalents without decreasing its affinity for red blood cells (K(d) 6-10 nM) with exposed phosphatidylserine. An average conjugation of 7.7 (range 3-13) diminished the binding 3-fold. Large-scale production and purification of [F-18]FBA-OSu from [F-18]fluoride was accomplished within 90 min and in 77% radiochemical yield (decay-corrected to the end of cyclotron bombardment). The conjugation reaction of annexin with [F-18]FBA-OSu was studied with respect to activity level, protein mass, and concentration. Under the most favorable conditions, >25 mCi [F-18]fluoroannexin (FAN) was isolated in 64% yield (decay-corrected for a 22 min conjugation process) from labeling 1.1 mg of annexin-V. A pilot PET imaging study of [F-18]fluoroannexin in normal rats showed high uptake in the renal excretory system and demonstrated sufficient clearance from most other internal organs within 1 h. [F-18]Fluoroannexin should prove useful in imaging targeted apoptosis.     

Conjugation of DOTA using isolated phenolic active esters: the labeling and biodistribution of albumin as blood pool marker

A convenient method for the functionalization of proteins with DOTA (1,4,7,10-tetraazacyclododecane-1,4,7,10-tetraacetic acid) has been developed. For this purpose DOTA was converted into a series of different monoreactive activated phenolic esters. The esters were prepared in a single step from commercially available DOTA, using 1-ethyl-3-[3-(dimethylamino)propyl]carbodiimide or 1,3-dicyclohexylcarbodiimide as coupling agent. The resulting activated esters were isolated by HPLC, lyophilized, and stored for future applications. In solid form the compounds exhibit high hydrolytic stability. The reactions with proteins proceeded in good yields. The conjugation and subsequent radiolabeling of the 4-nitrophenol ester of DOTA with 67Ga was investigated with rat serum albumin. A time-dependent biodistribution study in tumor bearing rats was conducted to demonstrate the integrity of the albumin conjugate. These results suggest that phenolic esters of DOTA represent versatile reagents to conjugate DOTA with proteins and other biomolecules in high yields.     

An N2S2 bifunctional chelator for technetium-99m and rhenium: complexation, conjugation, and epimerization to a single isomer.

A bifunctional chelator 6 was prepared bearing an N2S2 core for binding rhenium or technetium and a carboxylic acid group for conjugation to amino groups of biomolecules. Complexation of 6 with rhenium(V) resulted in two kinetic isomers, anti-7 and syn-7, being formed in approximately equal amounts. Epimerization with 0.5 M NaOH yields a single isomer anti-7, as determined by NMR spectroscopy and single-crystal X-ray analysis. The 99mTc complex was prepared at the tracer level by reaction of the ligand with 99mTcO4-, tin(II) chloride and sodium gluconate giving a mixture of two isomers, but showing a preference for the anti isomer. Chelation in the presence of 1 M NaOH results in anti-8 being formed as the sole product. The bifunctional ability of the ligand was explored by amide formation with (S)-alpha-phenethylamine, either by direct DCC coupling or through the N-hydroxy succinimidyl ester 9 intermediate. The deprotected bioconjugate 11 was complexed with rhenium, yielding similar amounts of two isomeric rhenium complexes, anti-12 and syn-12, which were isolated and characterized by NMR spectroscopy. Treatment of the kinetic mixture of anti-12 and syn-12 with 1 M NaOH resulted in quantitative conversion to a single rhenium complex anti-12. With technetium-99m in 0.1 M sodium acetate, bioconjugate 11 yielded both technetium-99m complexes anti-13 and syn-13, in a 2:1 ratio, respectively. In contrast, complexation in the presence of 1 M NaOH gave only one technetium-99m complex, assigned the structure anti-13.     

Solid-phase synthesis of 2-[18F]fluoropropionyl peptides

The 2-[(18)F]fluoropropionic (2-[(18)F]FPA) acid is used as a prosthetic group for radiolabeling proteins and peptides for targeted imaging using positron emission tomography (PET). Radiolabeling of compounds with more than one acylable functional group can lead to complex mixtures of products; however, peptides can be labeled regioselectively on the solid phase. We investigated the use of a solid-phase approach for the preparation of 2-[(18)F]fluoropropionyl peptides. [(18)F]FPA was prepared and conjugated to the peptides attached to the solid phase support. The (18)F-labeled peptides were obtained in 175 min with decay corrected yields of 10% (related to [(18)F]fluoride) and with a purity of 76-99% prior HPLC purification. The suitability of various coupling reagents and solid supports were tested for radiolabeling of several peptides of various lengths.     

PEGylation and biodistribution of an anti-MUC1 aptamer in MCF-7 tumor-bearing mice

Aptamers are characterized by a rapid renal clearance leading to a short in vivo circulating half-life. In order to use aptamers as anticancer therapeutic agents, their exposure time to the tumor has to be enhanced via increasing residency in the bloodstream. A way to achieve this goal is by conjugating the aptamer to poly(ethylene glycol) (PEG). Herein, we present the conjugation of a bifunctionalized anti-MUC1 aptamer (NH(2)-AptA-SR) with the (99m)Tc coordinating moiety MAG2 and either a conventional branched PEG or the comb-shaped PolyPEG via a two-step synthesis. The isolated products were radiolabeled with (99m)Tc and their biodistribution and tumor-targeting properties in MCF-7 tumor bearing mice were analyzed and compared.     

Rapid and efficient production of radiolabeled antibody conjugates using vacuum diafiltration guided by mathematical modeling

Increasing interest in the use of radiolabeled antibodies for cancer imaging and therapy drives the need for more efficient production of the antibody conjugates. Here, we illustrate a method for rapid and efficient production of radiolabeled antibody conjugates using vacuum diafiltration guided by mathematical modeling. We apply this technique to the production of 1,4,7,10-tetraazacyclododecane-1,4,7,10-tetraacetic acid (DOTA)-conjugated antibodies at the milligram and gram production scale and achieve radiolabeling efficiencies >95% using In-111. Using vacuum diafiltration, antibody-chelate conjugation and purification can be accomplished within the same vessel, and the entire process can be completed in <24 h. Vacuum diafiltration also offers safer and gentler processing conditions by eliminating the need to keep the retentate vessel under positive pressure through applied gas pressure or shear-inducing restriction points in the retentate flow path. Experimental data and mathematical model calculations suggest there exists a weak binding affinity (approximately 10(4)M(-1)) between the charged chelate molecules (e.g., DOTA) and the antibodies that slows the removal of excess chelate during purification. By analyzing the radiolabeling efficiency as a function of the number of diavolumes, we demonstrate the importance of balancing the removal of free chelate with the introduction of metal contaminants from the diafiltration buffer and also illustrate how to optimize radiolabeling of antibody conjugates under a variety of operating conditions. This methodology is applicable to the production of antibody conjugates in general.     

Efficient formation of heterodimers from peptides and proteins using unsymmetrical polyfluorophenyl esters of dicarboxylic acids

An efficient method for the heteroconjugation of biomolecules carrying free amino groups was reported previously, where mixed polyfluorophenyl diesters of dicarboxylic acids with varied aliphatic chain length were shown to be efficient reagents for the conjugation of a variety of model biomolecules. The concept was based on the differential reactivity of the esters towards amines. The concept has now been further optimized, and a 2,6‐difluorophenyl‐pentafluorophenyl diester combination has been demonstrated to be the most efficient, both with respect to selectivity and to reaction rate. A pentafluorophenyl ester reacts faster with an amino group and requires a weaker base than a 2,6‐difluorophenyl ester that requires a stronger base and longer reaction time. With the use of this combination of esters, we obtained considerably shortened reaction times compared with those reported previously, yet still retaining the desired selectivity in heteroconjugation. The increased reactivity of the bifunctional reagent allowed the construction of sophisticated peptide heteroconjugates from peptides, carbohydrates and proteins, showing a wide scope of applicability in the field of assembling functional bioconjugates. Copyright © 2012 European Peptide Society and John Wiley & Sons, Ltd.     

Synthesis of stable hydrazones of a hydrazinonicotinyl-modified peptide for the preparation of 99mTc-labeled radiopharmaceuticals.

Hydrazones of a 6-hydrazinonicotinyl-modified cyclic peptide IIb/IIIa receptor antagonist were prepared in order to protect the hydrazine moiety from reaction with trace aldehyde and ketone impurities encountered during the process of manufacturing and compounding lyophilized kits used in radiolabeling with (99m)Tc. Hydrazones were prepared by either a direct reaction of the 6-hydrazinonicotinyl-modified cyclic peptide with carbonyl compounds or by conjugation of the cyclic peptide with hydrazones of succinimidyl 6-hydrazinonicotinate. Stability of the hydrazones was evaluated by treatment with formaldehyde. Hydrazones derived from simple aliphatic aldehydes underwent an exchange reaction with formaldehyde, while hydrazones of aromatic aldehydes and ketones provided the greatest level of stability when challenged with formaldehyde. We have been successful in protecting 6-hydrazinonicotinyl-modified cyclic peptides from reacting with formaldehyde, while still allowing sufficient reactivity for radiolabeling with (99m)Tc. The hydrazones of succinimidyl 6-hydrazinonicotinate are convenient and general reagents for forming 6-hydrazinonicotinyl conjugates with amino-functionalized bioactive molecules.