Additional effects of silver nanoparticles on bactericidal efficiency depend on calcination temperature and dip-coating speed

There is an increasing interest in the application of photocatalytic properties for disinfection of surfaces, air, and water. Titanium dioxide is widely used as a photocatalyst, and the addition of silver reportedly enhances its bactericidal action. However, the synergy of silver nanoparticles and TiO(2) is not well understood. The photocatalytic elimination of Bacillus atrophaeus was examined under different calcination temperatures, dip-coating speeds, and ratios of TiO(2), SiO(2), and Ag to identify optimal production conditions for the production of TiO(2)- and/or TiO(2)/Ag-coated glass for surface disinfection. Photocatalytic disinfection of pure TiO(2) or TiO(2) plus Ag nanoparticles was dependent primarily on the calcination temperature. The antibacterial activity of TiO(2) films was optimal with a high dip-coating speed and high calcination temperature (600°C). Maximal bacterial inactivation using TiO(2)/Ag-coated glass was also observed following high-speed dip coating but with a low calcination temperature (250°C). Scanning electron microscopy (SEM) showed that the Ag nanoparticles combined together at a high calcination temperature, leading to decreased antibacterial activity of TiO(2)/Ag films due to a smaller surface area of Ag nanoparticles. The presence of Ag enhanced the photocatalytic inactivation rate of TiO(2), producing a more pronounced effect with increasing levels of catalyst loading.     

基于CdSe掺杂锐钛矿TiO_2的可见光体外灭活HL60细胞实验研究

用超声驱动方法合成了CdSe/TiO_2复合纳米粒子,并通过扫描电镜(SEM)、透射电镜(TEM)、X射线衍射(XRD)、紫外可见光(UV-Vis)吸收光谱和荧光(FS)光谱对CdSe/TiO_2复合纳米粒子进行表征。使用CCK-8法测定CdSe/TiO_2对白血病细胞的可见光光催化活性并通过SEM研究HL60细胞的表面超微结构形态。实验结果表明,用CdSe/TiO_2复合纳米粒子处理的组中观察到明显的HL60细胞生长抑制,并且HL60细胞在CdSe掺杂TiO_2复合纳米粒子作用下的PDT效率显著高于TiO_2,表明可以通过CdSe的修饰有效增强TiO_2的可见光光催化活性。此外,CdSe/TiO_2在可见光辐照下在4μg/m L的终值浓度下显示非常高的光动力效率,达76%。荧光光谱分析表明,CdSe/TiO_2复合纳米粒子可能通过分离光生空穴电子对提高此复合纳米粒子的光催化活性,从而提高CdSe/TiO_2对HL60细胞的PDT灭活效率。     

Proteomic analysis of early response lymph node proteins in mice treated with titanium dioxide nanoparticles

Human exposure to nanoparticles is inevitable from natural and anthropogenic sources. Titanium dioxide (TiO2) nanoparticles are increasingly being used in pharmaceutical and cosmetic products. Previous studies revealed that TiO2 levels were significantly increased in tissues (e.g., lymph nodes) after mice were injected with nanosized TiO2. To identify early response lymph node proteins to TiO2 nanoparticles, groups of mice were intradermally injected with a low dose of DeGussa P25 TiO2 nanoparticles or vehicle alone. The proteomes of lymph nodes at 24 h were quantitatively analyzed using trypsin-catalyzed 16O/18O labeling in conjunction with two-dimensional liquid chromatography separation and tandem mass spectrometry (2DLC-MS/MS). A total of 33 proteins were significantly changed (over 1.3-fold, p<0.05) in the mice treated with TiO2 nanoparticles, which accounted for approximately 1% of the total proteins identified. The differentially expressed proteins mainly involve the immune response (e.g., inflammation), lipid and fatty acid metabolism, mRNA processing, and nucleosome assembly. Regulation of functionally distinct classes of proteins could be mediated by estrogen receptor (ESR1), PPARγ, and c-Myc signalings, etc. The differentially expressed proteins identified in this experiment could represent early response proteins to TiO2 nanoparticle treatment in mouse lymph nodes.     

Photocatalytic activity of MCM-organized TiO(2) materials in the oxygenation of cyclohexane with molecular oxygen

The photooxygenation of cyclohexane by molecular oxygen has been investigated on two mesoporous TiO(2) materials, which have been prepared using colloidal nanoparticles as building blocks. One of the structured systems (mpTiO(2)-50) is a mixture of 50% TiO(2) and 50% SiO(2); the second one (mpTiO(2)-100) is constituted by 100% of TiO(2). Both mpTiO(2)-100 and mpTiO(2)-50 can induce cyclohexane photooxidation in repeated cycles, but with the former the yield in cyclohexanone is higher and only traces of cyclohexanol are observed. The results of experiments with different incident light intensities are reported: contrary to mpTiO(2)-50, the selectivity of mpTiO(2)-100 towards cyclohexanone is not significantly affected by the photonic flux. Based on the substrate conversion rates, incident photonic flux effects, photoluminescence and EPR spectra of the mesoporous materials, we infer that the photoreactivity of mpTiO(2)-100 and mpTiO(2)-50 is mainly controlled by textural effects. In particular, we propose that the inter-particle electron mobility that characterizes the mpTiO(2)-100 material, which is constituted exclusively of TiO(2) nanoparticles, entails a better utilization of electron traps for converting the photogenerated cyclohexyl-peroxide radicals to cyclohexanone.     

Photocatalytic inactivation of influenza virus by titanium dioxide thin film

Titanium dioxide (TiO(2)) under ultraviolet (UV) light produces a strong oxidative effect and may therefore be used as a photocatalytic disinfectant. Although many studies on the photocatalytic inactivation of bacteria have been reported, few studies have addressed virus inactivation. In the present study, we demonstrated the inactivation of influenza virus through TiO(2) photocatalysis using TiO(2) nanoparticles immobilized on a glass plate. The influences of the UV intensity, UV irradiation time and bovine serum albumin (BSA) concentration in the viral suspensions on the inactivation kinetics were investigated. Additionally, we also determined whether the International Organization for Standardization (ISO) methodology for the evaluation of antibacterial activity of TiO(2) photocatalysis could be applied to the evaluation of antiviral activity. The viral titers were dramatically reduced by the photocatalytic reaction. Even with a low intensity of UV-A (0.01 mW cm(-2)), a viral reduction of approximately 4-log(10) was observed within a short irradiation time. The viral inactivation kinetics were associated with the exposure time, the UV intensity and the BSA concentration in virus suspensions. These results show that TiO(2) photocatalysis could be used to inactivate the influenza virus. Furthermore, a minor modification of the ISO test method for anti-bacterial effects of TiO(2) photocatalysis could be useful for the evaluation of antiviral activity.     

Biogenic synthesis and photocatalysis of Pd-PdO nanoclusters reinforced hierarchical TiO2 films with interwoven and tubular conformations

Hierarchical nanocomposite films with Pd-PdO nanoparticles anchored uniformly on the inner surface of TiO2 nanotubes were achieved through a stepwise bioredox/artificial oxygenation approach by using the natural eggshell membrane (ESM) as a template. The Pd content ratio of Pd-PdO loading could be arbitrarily varied from 0 to 53 wt %, and the ESM-morphic nanocomposites Pd-PdO/TiO2 exhibited porous and multiphasic features, facilitating light transport and molecule accessibility to the active site during photocatalytic reactions. The photocatalytic activity of target nanocomposites was determined by the degradation of rhodamine B. The composites with a ratio of 10 wt % TiO2 (5 wt % Pd of Pd-PdO loading) presented a high degradation efficiency of 99.3% and showed good stability with a second run of about 95.3% and a third run of 94.6%. These composites with structural particularity and complexity are expected to find potential applications in various fields, such as photovoltaic devices, gas sensors, antistatic coating, dye-sensitized solar cells, etc.     

核壳结构CdS-TiO_2纳米颗粒体外光催化灭活白血病HL60细胞实验研究

本文研究了核壳结构CdS-TiO_2纳米颗粒光对HL60细胞光催化灭活作用,并初步探讨了CdS量子点增强TiO_2光催化灭活效率的作用机理。实验利用超声法制备了核壳结构CdS-TiO_2纳米颗粒,使用CCK-8法检测了其对白血病HL60细胞的光催化灭活效果,并采用活性氧分析和荧光发光光谱等分析手段对CdS量子点增强TiO_2光催化灭活效率的作用机理进行了分析。细胞实验结果表明,在暗室条件下,随着CdS包裹的TiO_2外壳的增厚,细胞的暗室存活率从28.5%逐渐上升至80%;在可见光照下,细胞的存活率显著下降。CdS-TiO_2纳米颗粒对HL60细胞的光催化灭活率均超过60%,其中CdS-TiO_2样品0.6对HL60细胞的光催化灭活效率最高,达到95%。根据荧光光谱和活性氧含量分析的结果推测,这可能是由于核壳结构的CdS内核与TiO_2外壳之间产生了有效的电子转移,抑制了TiO_2的空穴电子的复合,增强了TiO_2外壳的光催化活性,最终增加了TiO_2对HL60细胞的PDT灭活效果。     

New synthesis of a porous Si/TiO2 photocatalyst: testing its efficiency and stability under visible light irradiation.

TiO(2) nanoparticles were directly coupled with porous silicon and this novel composite material shows very strong photocatalytic activity for the degradation of Rhodamine B with high photochemical stability under visible light irradiation.     

Assessment of antimicrobial activity of nanosized Ag doped TiO2 colloids

In the present research, the antimicrobial effects of nanosized silver (Ag) doped TiO(2) colloidal solutions prepared using a sol-gel technique were investigated. In order to determine the solution characteristics, the turbidity, viscosity and pH of the colloidal solutions were measured. Differential thermal analysis-thermogravimetry equipment was used to determine the chemical structures and reaction types of the films formed from these solutions. The morphology of Ag doped TiO(2) nanoparticles was evaluated by atomic force microscopy. The disc diffusion method was employed to explore antimicrobial activity, and the Broth Microdilution method was used to obtain MIC values of nanosized Ag doped TiO(2) colloidal solutions against the test microorganisms Escherichia coli, Staphylococcus aureus, Candida albicans, Bacillus subtilis, and Salmonella typhimurium. It was found that the silver doped TiO(2) nanoparticles inhibited the growth and multiplication of the test microorganisms, including the fungus C. albicans. Antimicrobial activity was observed against all tested microorganisms at a very low concentration of 1.125-2.81 μg/ml of nano silver in 1-25 % Ag-TiO(2) solutions.     

Removal of benzene and toluene by carbonized bamboo materials modified with TiO2

Carbonized moso bamboo (Phyllostachys pubescens) was coated with TiO(2) nanoparticles to enhance its removal efficiency of harmful gases. Carbonized bamboo-TiO(2) composite (CBC) was prepared by heating mixtures of carbonized bamboo powder (CB) and TiO(2) nanoparticles, denoted as CBM, under nitrogen condition. TiO(2) nanoparticle and carbonized bamboo powder were mixed with the mass ratios of 1/1 and 2/1, respectively. At the same mass ratio of TiO(2) to CB, the benzene and toluene removal efficiencies follow the trend: CBC>CBM>CB, which is consistent with the amount of TiO(2) validated by elemental analysis. Sorption mechanism of benzene and toluene by CB, CBM and CBC might belong to hydrophobic-hydrophobic interaction, observed by depletion of untreated bamboo (UB) carbohydrates during carbonization. Sorption kinetics was further analyzed, and optimal correlation was found by fitting with the Elovich kinetic equation.     

Photoelectrocatalytic treatment of pentachlorophenol in aqueous solution using a rutile nanotube-like TiO2/Ti electrode.

Taking pentachlorophenol (PCP) as a reference, we investigated the photoelectrocatalytic degradation of organic pollutants using a rutile nanotube-like TiO(2)/Ti film electrode. The nanotube-like TiO2 electrode was prepared by first oxidizing the surface of a titanium sheet to form rutile TiO2 and then treating it to form the tubular structure in NaOH aqueous solution. The occurrence of PCP degradation was indicated by the decrease in pH, concentration of PCP and TOC, and by the formation of chloride ions. The photoelectrochemical (PEC) efficiency of the nanotube-like TiO2/Ti electrode has been determined in terms of degradation of PCP and the incident photo-to-current conversion efficiency (IPCE). The experimental results showed that PCP could be degraded more efficiently by a photoelectrocatalytic process than by a photocatalytic or electrochemical oxidation alone. A significant photoelectrochemical synergetic effect was observed. The kinetic constant of PEC degradation of PCP using a nanotube-like TiO2 electrode was over 60% higher than that using a TiO2 film electrode. It is noted that chloride ion and hydrogen ion concentration increased with irradiation time in the PEC degradation of PCP; PCP was gradually mineralized and the complete minimization of PCP took more time than its degradation.     

High-value chemicals obtained from selective photo-oxidation of glucose in the presence of nanostructured titanium photocatalysts

Glucose was oxidized in the presence of powdered TiO(2) photocatalysts synthesized by an ultrasound-promoted sol-gel method. The catalysts were more selective towards glucaric acid, gluconic acid and arabitol (total selectivity approx. 70%) than the most popular photocatalyst, Degussa P-25. The photocatalytic systems worked at mild reaction conditions: 30°C, atmospheric pressure and very short reaction time (e.g. 5 min). Such relatively good selectivity towards high-valued molecules are attributed to the physico-chemical properties (e.g. high specific surface area, nanostructured anatase phase, and visible light absorption) of novel TiO(2) materials and the reaction conditions. The TiO(2) photocatalysts have potential for water purification and energy production and for use in the pharmaceutical, food, perfume and fuel industries.     

Visible-light-induced bactericidal activity of a nitrogen-doped titanium photocatalyst against human pathogens

The antibacterial activity of photocatalytic titanium dioxide (TiO(2)) substrates is induced primarily by UV light irradiation. Recently, nitrogen- and carbon-doped TiO(2) substrates were shown to exhibit photocatalytic activities under visible-light illumination. Their antibacterial activity, however, remains to be quantified. In this study, we demonstrated that nitrogen-doped TiO(2) substrates have superior visible-light-induced bactericidal activity against Escherichia coli compared to pure TiO(2) and carbon-doped TiO(2) substrates. We also found that protein- and light-absorbing contaminants partially reduce the bactericidal activity of nitrogen-doped TiO(2) substrates due to their light-shielding effects. In the pathogen-killing experiment, a significantly higher proportion of all tested pathogens, including Shigella flexneri, Listeria monocytogenes, Vibrio parahaemolyticus, Staphylococcus aureus, Streptococcus pyogenes, and Acinetobacter baumannii, were killed by visible-light-illuminated nitrogen-doped TiO(2) substrates than by pure TiO(2) substrates. These findings suggest that nitrogen-doped TiO(2) has potential application in the development of alternative disinfectants for environmental and medical usages.     

Preparation and characterization of novel nanocomposite films formed from silk fibroin and nano-TiO2

This paper describes the synthesis and characterization of new regenerated silk fibroin (SF)/nano-TiO(2) composite films. The preparation method, based on the sol-gel technique using butyl titanate as oxide precursor, could avoid reagglomeration of the prepared nanoparticles. Samples were characterized mainly by X-ray diffraction (XRD), ultra-violet (UV) spectroscopy, atomic force microscopy (AFM), Fourier transform infrared (FT-IR) spectroscopy, and thermogravimetric analysis (TGA). The UV and AFM results indicated that TiO(2) nanoparticles could be well dispersed inside the SF film, and the size of TiO(2) was about 80nm. The XRD and FT-IR analysis implied that the formation of nano-TiO(2) particles may induce the conformational transition of silk fibroin to a typical Silk II structure partly with the increasing of crystallinity in the composite films. Compared to the pure SF films, the mechanical and thermal properties of composite films were improved, and the solubility in water was decreased due to the conformational transition of silk fibroin to Silk II structure.     

Formation of potential titanium antigens based on protein binding to titanium dioxide nanoparticles

Degradation products of titanium implants include free ions, organo-metallic complexes, and particles, ranging from nano to macro sizes. The biological effects, especially of nanoparticles, is yet unknown. The main objective of this study was to develop Ti-protein antigens in physiological solutions that can be used in testing of cellular responses. For this purpose, 0.1% TiO2 nanoparticles less than 100 nm were mixed with human serum albumin (HSA), 0.1% and 1%, in cell culture medium (DMEM, pH 7.2). The Ti concentrations in the resulting solutions were analyzed by inductively coupled plasma mass spectrometry. The stability of the nanoparticles in suspension was analyzed by UV-vis spectrophotometer and Dynamic Light Scattering. The concentration of Ti in suspension was dependent on the presence and concentration of HSA. Albumin prevented high aggregation rate of TiO2 nanoparticles in cell culture medium. It is shown that nano TiO2-protein stable aggregates can be produced under physiological conditions at high concentrations, and are candidates for use in cellular tests.     

Protein structural deformation induced lifetime shortening of photosynthetic bacteria light-harvesting complex LH2 excited state

Photosynthetic bacterial light-harvesting antenna complex LH2 was immobilized on the surface of TiO(2) nanoparticles in the colloidal solution. The LH2/TiO(2) assembly was investigated by the time-resolved spectroscopic methods. The excited-state lifetimes for carotenoid-containing and carotenoidless LH2 have been measured, showing a decrease in the excited-state lifetime of B850 when LH2 was immobilized on TiO(2). The possibility that the decrease of the LH2 excited-state lifetime being caused by an interfacial electron transfer reaction between B850 and the TiO(2) nanoparticle was precluded experimentally. We proposed that the observed change in the photophysical properties of LH2 when assembled onto TiO(2) nanoparticles is arising from the interfacial-interaction-induced structural deformation of the LH2 complex deviating from an ellipse of less eccentric to a more eccentric ellipse, and the observed phenomenon can be accounted by an elliptical exciton model. Experiment by using photoinactive SiO(2) nanoparticle in place of TiO(2) and core complex LH1 instead of LH2 provide further evidence to the proposed mechanism.     

Specific nitration at tyrosine 430 revealed by high resolution mass spectrometry as basis for redox regulation of bovine prostacyclin synthase

Treatment of bovine aortic microsomes containing active prostacyclin synthase (PGI(2) synthase) with increasing concentrations of peroxynitrite (PN) up to 250 microm of PN yielded specific staining of this enzyme on Western blots with antibodies against 3-nitrotyrosine (3-NT), whereas above 500 microm PN staining of additional proteins was also observed. Following treatment of aortic microsomes with 25 microm PN, PGI(2) synthase was about half-maximally nitrated and about half-inhibited. It was then isolated by gel electrophoresis and subjected to proteolytic digestion with several proteases. Digestion with thermolysin for 24 h provided a single specific peptide that was isolated by high performance liquid chromatography and identified as a tetrapeptide Leu-Lys-Asn-Tyr(3-nitro)-COOH corresponding to positions 427-430 of PGI(2) synthase. Its structure was established by precise mass determination using Fourier transform-ion cyclotron resonance-nanoelectrospray mass spectrometry and Edman microsequencing and ascertained by synthesis and mass spectrometric characterization of the authentic Tyr-nitrated peptide. Complete digestion by Pronase to 3-nitrotyrosine was obtained only after 72 h, suggesting that the nitrated Tyr-430 residue may be embedded in a tight fold around the heme binding site. These results provide evidence for the specific inhibition of PGI(2) synthase by nitration at Tyr-430 that may occur already at low levels of PN as a consequence of endothelial co-generation of nitric oxide and superoxide.     

Development of a self-sterilizing lancet coated with a titanium dioxide photocatalytic nano-layer for self-monitoring of blood glucose

A photocatalyst was applied to a lancet for pricking the finger to obtain an antibacterial property. A photocatalytic and uniform nano-layer of titanium dioxide (TiO2) on the surface of the lancet (0.36 mm x 24.5 mm) was formed by sputtering and annealed for crystallization of the TiO2 layer. By elementary analysis of the TiO2 layer, titanium and oxygen were detected. Next, for the estimation of the antibacterial properties resulting from the photocatalytic effect, the lancet was packed into a capillary tube filled with a suspension of Escherichia coli K-12 (non-spore-forming bacterium), and was continuously rolled in a continuous UV-irradiation system under black-light irradiation. Distinct antibacterial effects after irradiation at 0.5 mW cm(-2) for 45 min were observed in the crystallized TiO2 layer on the lancet. Finally, lancing resistances obtained by pricking an artificial skin sheet were examined using control lancets, and lancets with an unannealed TiO2 layer or an annealed TiO2 layer. The results showed almost the same lancing resistances for the control (0.53+/-0 N, n=3) and the lancet with an annealed TiO2 layer (0.51+/-0.018 N), while the lancet with an unannealed TiO2 layer showed a high lancing resistance compared with the other lancets (0.62+/-0.05 N). In conclusion, the lancet coated with a crystallized, velvety nano-layer of TiO2 obtained by annealing had antibacterial properties and a similar lancing resistance compared with the bare lancet, and showed potential for application in monitoring blood glucose in diabetes.     

Influence of reduction processes on the colour and photochromism of amorphous mesoporous TiO(2) thin films loaded with a silver salt

Silver nanoparticles were created inside mesoporous titania thin films by different reduction processes. We investigated the influence of the reduction method on the colour and photochromism of these amorphous TiO(2) films. The results highlight brown films by optical reduction, gray films by thermal reduction, and red, purple or orange films by chemical reduction. The different size distributions and localizations of the nanoparticles, characterized by UV-visible spectroscopy and electron microscopy, give various photochromic behaviours when exposed to visible laser light. We especially report the bleaching of different film colours under laser exposure.     

Visible-light-induced patterning of Au- and Ag-TiO2 nanocomposite film surfaces on the basis of plasmon photoelectrochemistry.

A novel technique for patterning based on visible light at Au-TiO2 and Ag-TiO2 nanocomposite film surfaces has been developed for the first time. TiO2 films loaded with Au and Ag nanoparticles were modified with hydrophobic thiols to obtain hydrophobic surfaces. The surfaces were converted to hydrophilic by visible light irradiation. Hydrophobic/hydrophilic patterning was also possible by visible light irradiation through a photomask. The patterning was due to removal of the thiol based on plasmon photoelectrochemistry. Visible-light-induced plasmon resonance at the Au and Ag nanoparticles gives rise to charge separation and redox reactions. The thiol is removed from the Au-TiO2 film probably by oxidative desorption, and from the Ag-TiO2 film owing chiefly to oxidation of Ag nanoparticles to Ag+.