Microemulsion electrokinetic chromatographic analysis of some polar compounds

This study presents the optimization of a microemulsion electrokinetic chromatographic (MEEKC) electrolyte solution by using UV detection and with the method, simultaneous separations of chemically, biochemically and pharmaceutically related anionic and cationic compounds. Representatives of the compound groups were from isoflavonoids, benzodiazepines, metanephrines, diuretics and peptide hormones. The MEEKC separations under basic conditions were first optimized using a two-component isoflavonoid mixture as the sample and an electrolyte containing 10 mM tetraborate as the main buffer (pH 9.5). The stable microemulsion phase was adjusted with various amounts of octane, 1-butanol and sodium dodecyl sulfate (SDS). An only acidified electrolyte solution used in the study was made of phosphoric acid (pH 1.8) containing octane, SDS and ethyl acetate. The analyses with isoflavonoids showed that electrophoretic mobilities of the investigated compounds were highly related to the concentrations of SDS and 1-butanol with linear and parabolic correlation, respectively. However, addition of octane gave linear correlation only at low concentrations. In most cases four to six structurally related compounds and even 13 diuretics with various polar properties were separated from each other in basic microemulsion medium. The acidified MEEKC electrolyte gave good resolution for anionic metanephrines.     

Microemulsion and micellar electrokinetic chromatography of steroids

A mixture of ten steroids was separated by microemulsion and micellar (SDS and glycodeoxyholate) electrokinetic chromatography systems. Separations were done on a 50 cm (to the detector) × 50 μm I.D. fused-silica capillary. Complete separation of all the test compounds in the micellar mode was obtained with glycodeoxycholate (50 mM) in 25 mM borate buffer, pH 6.5, as the micelle-forming agent. The best results, however, were obtained using microemulsion electrokinetic chromatography in which higher aliphatic alcohols were used as the microemulsion-forming modifiers. The system consisted of n-hexanol (0.81%), SDS (3.31%) and n-butanol (6.61%) in 20 mM phosphate buffer, pH 10.0 (89.28%, w/w). In the microemulsion mode, linear calibration for steroid standards was obtained in the concentration range 3 × 10⁻⁴ − 3 × 10⁻⁵ mol l⁻¹ with a detection limit of 1 pmol. The method was validated and applied to an 11β-hydroxysteroid dehydrogenase assay in tissues.     

Recovery of proteins from water-in-oil microemulsions in highly concentrated form through dilution techniques

Summary Bovine serum albumin (BSA) was recovered from water/Aerosol-OT (Sodium bis [2-ethylhexyl] sulfosuccinate)/isooctane water-in-oil microemulsion solution as a solid precipitate that was virtually free of surfactant by the addition of isooctane or 0.01 v/v 1-butanol. The recovery was greater when the fractional occupancy of BSA was higher and the extent of dilution greater. Proteins which interact with the microemulsion interface are more likely to be recovered.     

Preparation of submicrometer monodispersed magnetic silica particles using a novel water in oil microemulsion: properties and application for enzyme immobilization

The synthesis of monodispersed magnetic silica nanoparticles (MSN) is described using a water-in-oil reverse microemulsion system that does not require the use of co-surfactants. Sodium silicate, Tween 20 as a neutral surfactant and 1-butanol as the organic phase were used. There are several advantages of the proposed method including a saturation magnetization value of 10 emu/g for the particles obtained, uniformity of size and that they are easily functionalized to bind urease covalently. Moreover, the intra-day, inter-day and long-term stability results confirm that the procedure was successful and the enzyme-linked MSNs were stable over repeated uses and storage retaining more than 75 % activity after 4 months.     

Stripping of nonionic surfactants from the coacervate phase of cloud point system for lipase separation by Winsor II microemulsion extraction with the direct addition of alcohols

Extractive microbial fermentation of lipase by Serratia marcescens ECU1010 in cloud point system was previously carried out in the cloud point system. The direct addition of different alcohols, including iso-butanol, 2-phenylethanol and 1-octanol, into the coacervate phase of the clear supernatant of the fermentation broth formed microemulsion, where the nonionic surfactants and lipase were unevenly partitioned between the different phases in the microemulsion system. The polarity of alcohols strongly affected the microemulsion type at room temperature condition. The results indicated that the Winsor II microemulsion, formed by the addition of iso-butanol or 2-phenylethanol as the organic solvent, favored the stripping of the nonionic surfactant into the O_m phase, whereas the lipase was left in the excess aqueous phase. However, the Winsor I microemulsion, formed by the addition of 1-octanol as the organic solvent, failed to separate the lipase from the nonionic surfactant in the coacervate phase of cloud point system, because the nonionic surfactant and lipase were partitioned into the W_m phase at the same time. Moreover, in the Winsor II microemulsion extraction with 2-phenylethanol as the organic solvent, in which case the protein–surfactant complexes were absent at the interface between the O_m phase and the excess aqueous phase, the high lipase recovery (above 80%) and good nonionic surfactant removal were achieved. The effect of nonionic surfactants on lipase activity was also presented.     

Formulation,Characterization, and Clinical Evaluation of Microemulsion Containing Clotrimazole for Topical Delivery

The objective of the present study was to formulate and evaluate microemulsion systems for topical delivery of clotrimazole (CTM). The solubility of CTM in various oils was determined to select the oil phase of the microemulsion systems. Pseudoternary phase diagrams were constructed to identify the area of microemulsion existence. Five CTM microemulsion formulations (M1–M5) were prepared and evaluated for their thermodynamic stability, pH, refractive index, droplet size, viscosity, and in vitro release across cellulose membrane. Among the prepared microemulsion formulations, M3 (lemon oil/Tween 80/n-butanol/water) and M4 (isopropyl myristate/Tween 80/n-butanol/water) microemulsion systems were found to be promising according to their physical properties and CTM cumulative percentage release. Gel form of M3 and M4 were prepared using 1% Carbopol 940 as the hydrogel matrix. Both formulations were evaluated in the liquid and gel forms for drug retention in the skin in comparison to the marketed CTM topical cream and their stability examined after storage at 40°C for 6 months. Microemulsion formulations achieved significantly higher skin retention for CTM over the CTM cream. Stability studies showed that M4 preparations were more stable than M3. The in vitro anti-fungal activity of M4 against Candida albicans was higher than that of the conventional cream. Moreover, clinical evaluation proved the efficacy and tolerability of this preparation in the treatment of various topical fungal infections.     

Preparation and characterization of soluble starches having different molecular sizes and composition,by acid hydrolysis in different alcohols

Potato and waxy-maize starches were separately modified for 1 h at 65° with 0.36% hydrochloric acid in methanol, ethanol, 2-propanol, and 1-butanol. All of the modified starches were readily soluble in hot water, to give crystal-clear solutions up to a concentration of at least 20% (w/v). The modified granules were studied by light-microscopy and iodine-iodide staining. All of the modified starches retained their granule appearance, although with various degrees of damage that progressively increased from methanol to 1-butanol. Both hydrolysis and alcoholysis occurred, but to different extents in the different alcohols. The highest proportion of alcoholysis occurred in methanol where 50% of the resulting molecules were glycosides, the lowest in 1-butanol where 6% were glycosides. The number-average molecular weights of the modified starches also progressively decreased from 126,670 for the methanol-modified waxy-maize starch to 4,750 for the 1-butanol-modified potato starch. The methanol- and ethanol-modified potato starches were fractionated into amylose and amylopectin components. The 2-propanol- and 1-butanol-modified potato starches gave only an amylopectin component. The amylose components were characterized by gel-permeation chromatography on Bio-Gel A-5m, and the amylopectin components, on Bio-Gels A-150m and A-0.5m. The molecular sizes of the amylose and amylopectin components progressively decreased from methanol- to 1-butanol-modified starches. Furthermore, the polymodal composition of the amylopectin component was decreased to give a more homogeneous product. Waxy-maize starch was modified in methanol and 2-propanol and gave products that were of lower molecular size and more homogeneous than the polymodal native starch. It is shown that the differential effect of the different alcohols on the modification of the starch granules is produced by effecting different concentrations of acid inside the granule, where hydrolysis occurs in the 10–12% of water contained in the granule. It is postulated that 2-propanol and 1-butanol dissolve the double-helical, crystalline regions in the starch granule to give different types of products under otherwise identical conditions of modification.     

Effect of Formulation Components on the In Vitro Permeation of Microemulsion Drug Delivery System of Fluconazole

The purpose of this study was to evaluate the effect of formulation components on the in vitro skin permeation of microemulsion drug delivery system containing fluconazole (FLZ). Lauryl alcohol (LA) was screened as the oil phase of microemulsions. The pseudo-ternary phase diagrams for microemulsion regions were constructed using LA as the oil, Labrasol (Lab) as the surfactant and ethanol (EtOH) as the cosurfactant. The formulation which showed a highest permeation rate of 47.15 ± 1.12 μg cm⁻² h⁻¹ and appropriate physicochemical properties was optimized as containing 2% FLZ, 10% LA, 20% Lab/EtOH (1:1), and 68% double-distilled water (w/w). The efficiency of microemulsion formulation in the topical delivery of FLZ was dependent upon the contents of water and LA as well as Lab/EtOH mixing ratio. It was concluded that the percutaneous absorption of FLZ from microemulsions was enhanced with increasing the LA and water contents, and with decreasing the Lab/EtOH ratio in the formulation. Candida albicans was used as a model fungus to evaluate the antifungal activity of the best formula achieved, which showed the widest zone of inhibition as compared to FLZ reference. The studied microemulsion formulation showed a good stability for a period of 3 months. These results indicate that the studied microemulsion formulation might be a promising vehicle for topical delivery of FLZ.     

芦苇叶水提物的化感活性分析及潜在化感成分的筛选

采用不同溶剂对芦苇﹝Phragmites australis ( Cav.) Trin. ex Steud.﹞叶片水提物进行萃取,并以小麦( Triticum aestivum Linn.)和萝卜( Raphanus sativus Linn.)种子为实验材料对不同萃取物的化感效应进行检测;采用薄层层析和柱层析对抑制作用最强的正丁醇萃取物进行进一步分离,并采用GC-MS法对生物活性较高的组分进行组成成分分析;在此基础上,选择相对含量高并具有代表性的潜在化感成分进行生物活性检测,以期筛选出芦苇叶中的潜在化感成分。结果显示：随质量浓度(20、100和500 mg·L-1)提高,芦苇叶水提物的石油醚、二氯甲烷、乙酸乙酯、正丁醇和水萃取物对小麦和萝卜种子萌发的抑制作用均逐渐增强,其中正丁醇萃取物的抑制作用最强。在正丁醇萃取物的11个组分中,Fr.5、Fr.6、Fr.7、Fr.9和Fr.10组分均能显著抑制萝卜或小麦幼苗的生长,经质量浓度500 mg·L-1各组分处理液处理后萝卜或小麦幼苗的株高、根长及单株鲜质量均显著低于对照(P<0.05)。采用GC-MS法从Fr.5、Fr.6、Fr.7、Fr.9和Fr.10组分中分别鉴定出11、15、15、12和22种成分,分别占各组分总相对含量的83.02%、91.31%、87.36%、97.92%和94.34%,主要成分包括糖类、醇类、有机酸类、酮类、酰胺类和酯类。对14种潜在化感成分生物活性的检测结果显示这些成分对小麦幼苗生长有明显的抑制作用,其中,经质量浓度20 mg·L-1油酸酰胺、棕榈酸甲酯、亚油酸、2-苯乙胺、2-甲基烯丙醇和4-羟基-3-甲氧基苦杏仁酸处理后,小麦幼苗的株高、根长及单株鲜质量显著低于对照。综合分析结果显示：芦苇叶水提物具有较强的化感活性,其潜在的化感成分为油酸酰胺、棕榈酸甲酯、亚油酸、2-苯乙胺、2-甲基烯丙醇和4-羟基-3-甲氧基苦杏仁酸。     

Beta-hydroxysteroid dehydrogenase: activity in microemulsion and extraction from Pseudomonas testosteroni cells with microemulsion

The stability of purified beta-hydroxysteroid dehydrogenase activity measured as a function of time was good in buffered cationic and non-ionic microemulsions. The use of 1-pentanol and 1-hexanol in place of 1-butanol as cosurfactant gave increased activity and stability. The NAD+ Michaelis constant was 0.22 mM in buffer and 3.5 mM in waterpool concentration in microemulsion. Proteins, among them beta-hydroxysteroid dehydrogenase, were extracted from Pseudomonas testosteroni with cationic microemulsion, thus indicating that microemulsions may be utilized in protein release from cells.     

Substrate specificity and stereoselectivity of horse liver alcohol dehydrogenase. Kinetic evaluation of binding and activation parameters controlling the catalytic cycles of unbranched, acyclic secondary alcohols and ketones as substrates of the native and active-site-specific Co(II)-substituted enzyme

1. The steady-state parameters kcat and Km and the rate constants of hydride transfer for the substrates isopropanol/acetone; (S)-2-butanol, (R)-2-butanol/2-butanone; (S)-2-pentanol, (R)-2-pentanol/2-pentanone; 3-pentanol/3-pentanone; (S)-2-octanol and (R)-2-octanol have been determined for the native Zn(II)-containing horse-liver alcohol dehydrogenase (LADH) and the specific active-site-substituted Co(II)LADH. 2. A combined evaluation of steady-state kinetic data and rate constants obtained from stopped-flow measurements, allowed the determination of all rate constants of the following ordered bi-bi mechanism: E in equilibrium E.NAD in equilibrium E.NAD.R1R2 CHOH in equilibrium E.NADH.R1R2CO in equilibrium E.NADH in equilibrium E. 3. On the basis of the different substrate specificities of LADH and yeast alcohol dehydrogenase (YADH), a procedure has been developed to evaluate the enantiomeric product composition of ketone reductions. 2-Butanone and 2-pentanone reductions revealed (S)-2-butanol (86%) and (S)-2-pentanol (95%) as the major products. 4. The observed enantioselectivity implies the existence of two productive ternary complexes; E.NADH.(pro-S) 2-butanone and E.NADH.(pro-R) 2-butanone. All rate constants describing the kinetic pathways of the system (S)-2-butanol, (R)-2-butanol/2-butanone have been determined. These data have been used to estimate the expected enantiomer product composition of 2-butanone reductions using apparent kcat/Km values for the two different ternary-complex configurations of 2-butanone. Additionally, these data have been used for computer simulations of the corresponding reaction cycles. Calculated, simulated and experimental data were found to be in good agreement. Thus, the system (S)-2-butanol, (R)-2-butanol/2-butanone is the first example of a LADH-catalyzed reaction for which the stereochemical course could be described in terms of rate constants of the underlying mechanism. 5. The effects of Co(II) substitution on the different steps of the kinetic pathway have been investigated. The free energy of activation is higher for alcohol oxidation and lower for ketone reduction when catalyzed by Co(II)LADH in comparison to Zn(II)LADH. However, the free energies of binding are affected by metal substitution in such a way that the enantioselectivity of ketone reduction is not significantly changed by the substitution of Co(II) for Zn(II). 6. Evaluation of the data shows that substrate specificity and stereoselectivity result from combination of the free energies of binding and activation, with differences in binding energies as the dominating factors. In this regard, the interactions of substrate molecules with the protein moiety are dominant over the interactions with the catalytic metal ion.     

The effects of the phospholipase D-antagonist 1-butanol on seedling development and microtubule organisation in Arabidopsis

The organisation of plant microtubules into distinct arrays during the cell cycle requires interactions with partner proteins. Having recently identified a 90-kDa phospholipase D (PLD) that associates with microtubules and the plasma membrane [Gardiner et al. (2001) Plant Cell 13: 2143], we exposed seeds and young seedlings of Arabidopsis to 1-butanol, a specific inhibitor of PLD-dependent production of the signalling molecule phosphatidic acid (PA). When added to agar growth media, 0.2% 1-butanol strongly inhibited the emergence of the radicle and cotyledons, while 0.4% 1-butanol effectively blocked germination. When normal seedlings were transferred onto media containing 0.2% and 0.4% 1-butanol, the inhibitor retarded root growth by about 40% and 90%, respectively, by reducing cell elongation. Inhibited plants showed significant swelling in the root elongation zone, bulbous or branched root hairs, and modified cotyledon morphology. Confocal immunofluorescence microscopy of root tips revealed that 1-butanol disrupted the organisation of interphase cortical microtubules. Butanol isomers that do not inhibit PLD-dependent PA production, 2- and 3-butanol, had no effect on seed germination, seedling growth, or microtubule organisation. We propose that production of PA by PLD may be required for normal microtubule organisation and hence normal growth in Arabidopsis.     

Direct enantiomeric resolutions of chiral triazole pesticides by high-performance liquid chromatography

Cellulose-tris (3,5-dimethylphenylcarbamate; CDMPC) was synthesized and coated on aminopropylsilica to prepare chiral stationary phase (CSP). Normal-phase high-performance liquid chromatography (HPLC) methods for the resolutions of five chiral triazole pesticides, diniconazole, tebuconazole, hexaconazole, triadimefon and flutriafol, on the CSP were developed. Several operating parameters such as mobile phase composition, modifier and column temperature were studied for the optimization of the resolutions. Better separations were achieved using 2% iso-butanol for diniconazole, 2% ethanol for tebuconazole, 2% iso-propanol for hexaconazole, 1% n-butanol for triadimefon and 2% n-propanol for flutriafol as modifiers in n-hexane at 0 degrees C with the resolution factors (Rs) of 1.62, 1.66, 2.46, 1.68 and 1.98, respectively. Low temperature was better for the resolutions. Validation of the methods included linearity and precision.     

Development and antifungal evaluation of a food-grade U-type microemulsion

Aims: Food-grade microemulsions have been of increasing interest to researchers as potential delivery systems for bioactive compounds. However, food-grade microemulsions are difficult to formulate and no microemulsion has been documented for antifungal purpose. The physicochemical characterization of a food-grade glycerol monolaurate (GML)/ethanol (EtOH)/Tween 80/potassium sorbate (PS)/water microemulsion system and the antifungal activities against Aspergillus niger and Penicillium italicum have been studied in this paper. Methods and Results: The influence of EtOH and PS on oil solubilization capability was clearly reflected in the phase behaviour of U-type microemulsion systems. One dilution-stable formulation ME (GML/EtOH/Tween 80/PS/water = 3 : 3 : 3·5 : 10·5 : 16) was selected. After 4 days of incubation, ME showed 80%A. niger growth inhibition at 0·2% and 72%P. italicum growth inhibition at 0·1%, respectively, and a delay of conidiation of 2 days compared with the control. In the antifungal activities of the microemulsion, GML and PS made major contributions with similar antifungal activities at a GML/PS weight ratio of 1: 3·5. Conclusions: Food-grade dilution-stable microemulsions prepared with GML as oil phase for antifungal purpose are feasible and solubilization of a hydrotrope contributes to the formation of microemulsions and enhanced antifungal activities. Significance and Impact of the Study: The present report represents the first to develop a food-grade microemulsion system for antifugal purpose.     

Amino Acid Sequences of Glycopeptides from Cucumisin

Oxidation of short-chain iso-alkanes (isobutane, isopentane, 2-methylpentane, and 3-methylpentane) was studied with propane-grown resting mycelia of Scedosporium sp. A-4. Isobutane was oxidized to terf-butanol, but both isobutane and tert-butanol were not used for growth. Isopentane was oxidized to 3-methyl-1-butanol, 2-methyl-2-butanol, and 3-methyl-2-butanol but not to 2-methyl-1-butanol. 2-Methylpentane was oxidized to 4-methyl-1-pentanol, 2-methyl-2-pentanol, and 4-methyl-2-pentanol but not to 2-methyl-1-pentanol or 2-methyl-3-pentanol. 3-Methylpentane was not oxidized. Oxidation of branched alcohols was also studied.     

Anti-yeast activity of a food-grade dilution-stable microemulsion

The anti-yeast activities of a food-grade dilution-stable microemulsion against Candida albicans and Saccharomyces cerevisiae have been studied. The weight ratio of the formulated microemulsion is glycerol monolaurate (GML)/propionic acid/Tween 80/sodium benzoate (SB)/water = 3:9:14:14:24. Results of anti-yeast activity on solid medium by agar diffusion method showed that the anti-yeast activity of the microemulsion at 4.8 mg/ml was comparable to that of natamycin at 0.1 mg/ml as positive control. Results of anti-yeast activity in liquid medium by broth dilution method showed that the growth of both C. albicans and S. cerevisiae was completely inhibited when the liquid medium containing 10⁶ cfu/ml was treated with 1.2 mg/ml microemulsion, which was determined as minimum fungicidal concentration. The kinetics of killing results showed that the microemulsion killed over 90% yeast cells rapidly within 15 min and caused a complete loss of viability in 120 min. Among the components, SB and GML had a similar anti-yeast activity, followed by propionic acid, while Tween 80 exhibited no activity and could not enhance the anti-yeast activities of these components, and it was revealed that the anti-yeast activity of the microemulsion was attributed to a combination of propionic acid, GML, and SB. The anti-yeast activity of the microemulsion was in good agreement with the leakage of 260-nm absorbing materials and the observation of transmission electron microscopy, indicating that the microemulsion induced the disruption and dysfunction of the cell membrane.     

Study of isopropyl myristate microemulsion systems containing cyclodextrins to improve the solubility of 2 model hydrophobic drugs

The objectives of this project were to evaluate the effect of alkanols and cyclodextrins on the phase behavior of an isopropyl myristate microemulsion system and to examine the solubility of model drugs. Triangular phase diagrams were developed for the microemulsion systems using the water titration method, and the solubility values of progesterone and indomethacin were determined using a conventional shake-flask method. The water assimilation capacities were determined to evaluate the effective microemulsion formation in different systems. The alkanols showed higher microemulsion formation rates at higher concentrations. A correlation between the carbon numbers of the alkanol and water assimilation capacity in the microemulsions studied was observed; isobutanol and isopentanol produced the best results. The addition of cyclodextrins showed no effect or had a negative effect on the microemulsion formation based on the type of cyclodextrin used. Isopropyl myristate-based microemulsion systems alone could increase the solubility values of progesterone and indomethacin up to 3300-fold and 500-fold, respectively, compared to those in water. However, the addition of cyclodextrins to the microemulsion systems did not show a synergistic effect in increasing the solubility values of the model drugs. In conclusion, microemulsion systems improve the solubility of progesterone and indomethacin. But the two types of cyclodextrins studied affected isopropyl myristatebased microemulsion systems negatively and did not improve the solubilization of 2 model drugs.     

Pairwise interaction enthalpies of enantiomers of β-amino alcohols in DMSO + H2O mixtures at 298.15 K

The dilution enthalpies of enantiomers of six β-amino alcohols, namely (R)-(-)-2-amino-1-propanol versus (S)-(+)-2-amino-1-propanol, (R)-(-)-2-amino-1-butanol versus (S)-(+)-2-amino-1-butanol, and (R)-(-)-2-amino-1-pentanol versus (S)-(+)-2-amino-1-pentanol in dimethylsulfoxide (DMSO) + H(2)O mixtures (mass fractions of DMSO w = 0 to 0.3) have been determined respectively using an isothermal titration calorimeter (MicroCal ITC200, Northampton, MA, USA) at 298.15 K. According to the McMillan-Mayer theory, the corresponding homochiral enthalpic pairwise interaction coefficients (h(XX)) of the six amino alcohols have been calculated. It is found that across the whole studied composition range of mixed solvent, values of h(XX) for S-enantiomer are almost universally higher than those of R-enantiomer for each amino alcohol and that the variations of h(XX) depend largely on the composition of mixed solvent. The results were interpreted from the point of view of solute-solute interaction mediated by cosolvent DMSO, as well as competition equilibrium between hydrophobic-hydrophobic, hydrophilic-hydrophilic, and hydrophobic-hydrophilic interactions.     

Conformational preference and ligand binding properties of DNA junctions are determined by sequence at the branch

Four-arm DNA branched junctions are stable analogues of Holliday recombinational intermediates. A number of four-arm DNA junctions synthesized from oligonucleotides have now been studied. Gel mobility or chemical footprinting experiments on several immobile four-arm junctions indicate that in the presence of Mg2+, they assume a preferred conformation consisting of two helical domains, each formed by stacking a particular pair of arms on each other. We show here that a junction we designate as J1c that has the same chemical composition as one we have previously studied in detail, J1, but is formed from the four strands complementary to those of the latter, exhibits the reverse stacking preference. The pattern of self-protection of the strands of J1c exposed to Fe(II).EDTA-induced scission reveals that twofold symmetry is preserved, but the opposite pair of strands preferentially cross over. Moreover, the Fe(II).EDTA scission profiles of J1c indicate that this junction exhibits a weaker bias as to which strands cross over than is observed in J1. The preference for the dominant species in J1 is 1.3 times greater than in J1c at 4 degrees C and in the presence of 10 mM Mg2+, based on chemical reactivity data. This is confirmed by a cleavage experiment using the resolvase enzyme, endonuclease I, from bacteriophage T7. This difference could reflect either sequence-dependent differences in the equilibrium among isomers, or in the structure of these junctions. Chemical footprinting experiments using the probes MPE.Fe(II) and (OP)2Cu(I) show that the high-affinity ligand binding site in immobile junctions is determined by junction geometry.     

Characterization of microemulsion structures in the pseudoternary phase diagram of isopropyl palmitate/water/Brij 97:1-butanol

This research was aimed to characterize microemulsion systems of isopropyl palmitate (IPP), water, and 2∶1 Brij 97 and 1-butanol by different experimental techniques. A pseudoternary phase diagram was constructed using water titration method. At 45% wt/wt surfactant system, microemulsions containing various ratios of water and IPP were prepared and identified by electrical conductivity, viscosity, differential scanning calorimetry (DSC), cryo-field emission scanning electron microscopy (cryo-FESEM) and nuclear magnetic resonance (NMR). The results from conductivity and viscosity suggested a percolation transition from water-in-oil (water/oil) to oil-in-water (oil/water) microemulsions at 30% wt/wt water. From DSC results, the exothermic peak of water and the endothermic peak of IPP indicated that the transition of water/oil to oil/water microemulsions occurred at 30% wt/wt water. Cryo-FESEM photomicrographs revealed globular structures of microemulsions at higher than 15% wt/wt water. In addition, self-diffusion coefficients determined by NMR reflected that the diffusability of water increased at higher than 35% wt/wt water, while that of IPP was in reverse. Therefore, the results from all techniques are in good agreement and indicate that the water/oil and oil/water transition point occurred in the range of 30% to 35% wt/wt water.