Biodegradation of Total Petroleum Hydrocarbons from Oily Sludge

The present study concerns the biotreatment of oily sludge of petroleum refineries. Experiments were performed to assess the degradation potential of the microbial species present in the oily sludge through augmentation, and using the augmented microbial inoculums to treat oily sludge in a slurry form containing mineral medium and water. The optimum pH of the slurry was found to be 8 for the biodegradation of oily sludge. The effect of oily sludge concentration, stirring rate, and treatment time on degradation of total petroleum hydrocarbons (TPH) was studied. It was found that the degradation process consists of two consecutive stages and that each stage follows a first-order kinetics. The first stage lasted 4 days followed by a second stage up to 7 days. The faster first stage had a rate constant of 0.1 day^?1, whereas the slower second stage had a rate constant of 0.056 day^?1. The kinetics was found to be time-dependent. The study showed that the mineral medium provided essential nutrients to the microbial species and that the degradation efficiency of the whole microbial species present in the oily sludge was quite high (～90%).     

Fate of Hydrocarbons During Oily Sludge Disposal in Soil

A 1,280-day laboratory simulation of the “landfarming” process explored the fate in soil of polynuclear aromatics (PNAs) and total extractable hydrocarbon residues originating from the disposal of an oily sludge. In addition to the measurement of CO₂ evolution, periodic analyses of PNAs and hydrocarbons monitored biodegradation activity. The estimation of carbon balance and of soil organic matter assessed the fate of residual hydrocarbons. Seven sludge applications during a 920-day active disposal period were followed by a 360-day inactive “closure” period with no further sludge applications. A burst of CO₂ evolution followed each sludge addition, but substantial amounts of undegraded hydrocarbons remained at the end of the study. Hydrocarbon accumulation did not inhibit biodegradation performance. Conversion of hydrocarbons to CO₂ predominated during active disposal; incorporation into soil organic matter predominated during the closure period. In this sludge, the predominant PNAs were degraded more completely (85%) than total hydrocarbons. Both biodegradation and abiotic losses of three- and four-ring PNAs contributed to this result. Some PNAs with five and six rings were more persistent, but these constituted only a small portion of the PNAs in the sludge. The study confirmed that the microbially mediated processes of mineralization and humification remove sludge hydrocarbons from soils of landfarms with reasonable efficiency.     

Enhanced Biodegradation of Petroleum Hydrocarbons in Contaminated Soil

Soil samples taken from a contaminated site in Northern Quebec, Canada, exhibited a low capacity for biodegradation of total petroleum hydrocarbons (TPH), despite a high capacity for the mineralization of aromatic hydrocarbons and a low toxicity of soil leachates as measured by Microtox assay. Toxicity assays directly performed on surface soil, including earthworm mortality and barley seedling emergence, indicated moderate to high levels of toxicity. Soil biostimulation did not improve the removal of petroleum hydrocarbons, while bioaugmentation of soil with a developed enrichment culture increased the efficiency of hydrocarbon removal from 20.4% to 49.2%. A considerable increase in the removal of TPH was obtained in a bioslurry process, enhancing the mass transfer of hydrocarbons from soil to the aqueous phase and increasing the efficiency of hydrocarbon removal to over 70% after 45 days of incubation. The addition of ionic or nonionic surfactants did not have a significant impact on biodegradation of hydrocarbons. The extent of hydrocarbon mineralization during the bioslurry process after 45 days of incubation ranged from 41.3% to 58.9%, indicating that 62.7% to 83.1% of the eliminated TPH were transformed into CO₂ and water.     

Enhanced Biodegradation of Petroleum Hydrocarbons in Contaminated Soil

Soil samples taken from a contaminated site in Northern Quebec, Canada, exhibited a low capacity for biodegradation of total petroleum hydrocarbons (TPH), despite a high capacity for the mineralization of aromatic hydrocarbons and a low toxicity of soil leachates as measured by Microtox assay. Toxicity assays directly performed on surface soil, including earthworm mortality and barley seedling emergence, indicated moderate to high levels of toxicity. Soil biostimulation did not improve the removal of petroleum hydrocarbons, while bioaugmentation of soil with a developed enrichment culture increased the efficiency of hydrocarbon removal from 20.4% to 49.2%. A considerable increase in the removal of TPH was obtained in a bioslurry process, enhancing the mass transfer of hydrocarbons from soil to the aqueous phase and increasing the efficiency of hydrocarbon removal to over 70% after 45 days of incubation. The addition of ionic or nonionic surfactants did not have a significant impact on biodegradation of hydrocarbons. The extent of hydrocarbon mineralization during the bioslurry process after 45 days of incubation ranged from 41.3% to 58.9%, indicating that 62.7% to 83.1% of the eliminated TPH were transformed into CO₂ and water.     

Biodegradation of Petroleum Hydrocarbons in a Soil Polluted Sample by Oil-Based Drilling Cuttings

Microbial degradation of hydrocarbons in soils polluted by oil-based drilling mud and cuttings has been investigated by static methods such as composting or biopiling. Bioremediation of polluted soils by oil-based drilling cuttings through a slurry bioreactor has not previously been reported. The main aim of this work is to monitor hydrocarbon biodegradation in slurry of drilling cuttings and unpolluted soils and the effects of nutrients on it. Indigenous, bacterial-mixed culture isolated from a polluted soil by drilling cuttings adapted to drilling mud concentrations up to 15% (v/v) was done during a 15-month program. The total petroleum hydrocarbons’ (TPHs) removal efficiency in C/N/P 100/5/1 ratio was 90.5 and 79.85% under experimental and control conditions, respectively. The microbial count on the first day, 15 × 10⁷ CFUg^?1, reached 20 × 10⁹ CFUg^?1on the twenty-first day at experimental conditions. The TPH removal efficiency in C/N/P 100/10/2 was 92.5 and 82.25% at experiment and control, respectively. Increasing nitrogen and phosphorous amount couldn't increase microbial count in comparison with C/N/P ratio 100/5/1. The measured biomass contents and microbial counts in experiments were significantly higher than the control and confirmed hydrocarbons’ biodegradation during the time. Results showed that slurry bioreactors could accelerate the biodegradation of TPHs and reduce remediation time in soil polluted by oil-based drilling cuttings.     

石油烃类的微生物降解

石油作为重要能源之一已被世界各国广泛使用,由于在石油的开采、储存、运输、加工和石化产品生产等过程中的漏油以及突发性泄油事故致使大量的石油进入环境造成污染。石油污染的危害主要表现在对土壤生态系统的结构和功能的破坏,严重影响土壤的透气性和渗水性,导致土壤板结、肥力下降;在水体表面形成油膜,致使水中溶氧量急剧下降,造成水生生物的大量死亡,破坏水生生态环境和渔业资源;还可进入地下水系,直接污染地下水源,影响居民用水和农田灌溉;石油中的一些致畸致癌物质还可通过食物链的生物富集作用而直接危害人类健康。随着人们对环境问题的日益关注,石油烃类的微生物降解研究工作也不断得以深入。近十年来这一领域又有许多研究和相关报道,本文对相关工作进行了综述。     

Kinetics of Acetate Metabolism during Sludge Digestion

The quantitative contribution of acetic acid to methane production was studied by use of C(14)-labeled acetic acid. Samples of domestic sewage sludge were incubated anaerobically in Warburg vessels. The rate of methane production in the vessels was 0.033 mumoles per ml per min. C(14)-labeled acetic acid was added, and the turnover rate was calculated. The pool size of acetic acid in the sludge was 4.7 mumoles/ml. The turnover rate was 0.0052 min(-1), giving a rate of formation of acetic acid of 0.024 mumoles per ml per min. Under these conditions, acetic acid would account for approximately 73% of the methane produced by the sludge. Acetic acid was found to exist primarily in an extracellular pool. The turnover rate of the extracellular pool was rapid, and it was concluded that most of the acetic acid must be metabolized to methane by a specialized microflora not involved in the formation of acetic acid.     

Biodegradation of Aromatic Hydrocarbons in an Extremely Acidic Environment

The potential for biodegradation of aromatic hydrocarbons was evaluated in soil samples recovered along gradients of both contaminant levels and pH values existing downstream of a long-term coal pile storage basin. pH values for areas greatly impacted by runoff from the storage basin were 2.0. Even at such a reduced pH, the indigenous microbial community was metabolically active, showing the ability to oxidize more than 40% of the parent hydrocarbons, naphthalene and toluene, to carbon dioxide and water. Treatment of the soil samples with cycloheximide inhibited mineralization of the aromatic substrates. DNA hybridization analysis indicated that whole-community nucleic acids recovered from these samples did not hybridize with genes, such as nahA, nahG, nahH, todC1C2, and tomA, that encode common enzymes from neutrophilic bacteria. Since these data suggested that the degradation of aromatic compounds may involve a microbial consortium instead of individual acidophilic bacteria, experiments using microorganisms isolated from these samples were initiated. While no defined mixed cultures were able to evolve ¹⁴CO₂ from labeled substrates in these mineralization experiments, an undefined mixed culture including a fungus, a yeast, and several bacteria successfully metabolized approximately 27% of supplied naphthalene after 1 week. This study shows that biodegradation of aromatic hydrocarbons can occur in environments with extremely low pH values.     

Kinetics of Endosulfan Biodegradation by Stenotrophomonas maltophilia EN-1 Isolated From Pesticide-Contaminated Soil

Endosulfan is one of the persistent organochlorinated pesticides used extensively throughout the world, particularly in the developing countries. Its microbial metabolic transformation product endosulfan sulphate is more toxic and persistent than the parent compound itself. In order to completely mineralize endosulfan, augmentation of soil microbial community with efficient endosulfan degradation properties could a potentially viable option. In the present study, endosulfan degrading bacterium was isolated from the agriculture-contaminated soil of Shujaabad, Multan, Pakistan by using enrichment technique. The isolated bacterial strain EN-1 (Endosulfan-1) was identified as S. maltophilia by 16S rRNA sequencing and biochemical analysis. EN-1 has demonstrated the ability to utilize endosulfan as sole sulfur source. Kinetics of endosulfan degradation was studied at various initial concentrations ranges from 5 mg/L to 100 mg/L by growth dependent and growth independent kinetic models. Biodegradation kinetics revealed that the bacterium was highly efficient in endosulfan degradation. The average values of kinetic constants i.e. K_s, and µ_max were 13.73 mg/L and 0.210 h^?1 respectively, while µ_max/K_s ratio was 0.015. Addition of sulfur decreased the rate of degradation as the µ_max/K_s was observed to reduce. GC-MS analysis revealed that the bacterium metabolised the endosulfan into non-toxic metabolite i.e. endosulfan diol. The study instigates a complete elucidation of degradation process for commercial applications.     

Distribution and Physiological State of Microorganisms in Petrochemical Oily Sludge

The occurrence, vertical distribution, and physiological state of microorganisms in a petrochemical oily sludge deposit were studied. The total number and the number of viable microbial cells at depths of 0.2 and 3 m were about 10¹⁰ and 10⁸ cells/g dry wt sludge. Most microbial cells taken from the middle (1 m deep) and the bottom (3 m deep) sludge horizons showed a delayed colony-forming ability, which suggested that the cells occurred in a hypometabolic state. The relative number of microaerobic denitrifying microorganisms steeply increased with depth. The amount of microorganisms tolerant to 3, 5, and 10% NaCl and capable of growing at 7 and 40°C varied from 10² to 10⁸ CFU/g dry wt sludge. Petrochemical oily sludge was found to maintain the growth of heterotrophs, among which the degraders of oily sludge and ten different individual polycyclic aromatic hydrocarbons were detected. The occurrence of highly adaptable microorganisms with an adequate metabolic potential in the petrochemical oily sludge deposit implies that its bioremediation is possible without introducing special microorganisms.     

Prepared Bed Land Treatment of Soils Containing Diesel and Crude Oil Hydrocarbons

An ex situ, field-scale, prepared bed land treatment unit (LTU) was used to bio-remediate soils containing petroleum hydrocarbons. Two soils were treated in side-by-side units to compare performance: (1) a clayey silt containing crude oil hydrocarbons from releases 30 to 40 years ago and (2) a silty sand containing diesel fuel hydrocarbons from a leak about three years prior to the bioremediation. The effectiveness of the bioremediation in the LTU was evaluated over a period of 18 months. The results indicated that: (1) prepared bed bioremediation reduced the hydrocarbon concentration, mobility, and relative toxicity in the soil with the diesel fuel, and (2) chemical bioavailability appeared to limit bioremediation of the soil containing the crude oil hydrocarbons. Although the soils containing the crude oil hydrocarbons contained an average of 10,000?mg TPH/kg dry soil, these soils had limited hydrocarbon availability, nontoxic conditions, and low potential for chemical migration. For the soils containing the diesel fuel, active prepared bed bioremediation of about 15 weeks was adequate to reach an environmentally acceptable endpoint. At that time, there was little further TPH loss, no Microtox^TM toxicity, and limited hydrocarbon mobility.     

Biodegradation Rates for Fuel Hydrocarbons and Chlorinated Solvents in Groundwater

Numerous studies presented in the general literature have shown that the key mechanism affecting the rate and extent of migration of a contaminant plume is biodegradation since it removes contaminant mass and reduces average plume concentrations. This paper attempts to address the importance of biodegradation for fuel and chlorinated solvent plumes and to present a comprehensive review of rates of biodegradation obtained from field and laboratory studies. Data from approximately 280 studies are statistically analyzed to determine ranges of biodegradation rates for various contaminants under different redox conditions. A review of 133 studies for fuel hydrocarbons has yielded first-order biodegradation coefficients up to 0.445 day^-1 under aerobic conditions and up to 0.522^-1 under anaerobic conditions in 90% of the cases. A median rate constant for benzene of 0.3% day^-1 was estimated from all studies, while those for toluene, ethylbenzene, and xylenes were estimated to be 4, 0.3, and 0.4% day^-1, respectively. On the other hand, data from 138 studies with chlorinated solvents show that the less chlorinated compounds biodegrade in the 90% of the cases with rate constants lower than 1.35 day^-1 under aerobic conditions and that highly chlorinated compounds biodegrade with decay coefficients up to 1.28 day^-1 in 90% of the anoxic experiments. Median decay coefficients derived from all studies were 4.9, 0.07, 0.42, 0.86, 1.02, 0.44, and 4.7 day^-1 for carbon tetrachloride, dichloroethane (DCA), cis-1,2-dichloroethene (cis-1,2-DCE), tetrachloroethene (PCE), trichloroethane (TCA), trichloroethene (TCE), and vinyl chloride, respectively. The rate constants presented in this study can be used in screening and modeling studies and to guide the assessment of natural attenuation as a viable remedial technology at contaminated sites. represent a compilation of available literature data.     

Activated Sludge Biodegradation of 12 Commercial Phthalate Esters

The activated sludge biodegradability of 12 commercial phthalate esters was evaluated in two test systems: (i) a semicontinuous activated sludge test and (ii) an acclimated 19-day die-away procedure. Both procedures demonstrated that phthalate esters are rapidly biodegraded under activated sludge conditions when loss of the parent phthalate ester (primary degradation) is measured.     

Biodegradation of RDX in Unsaturated Soil

Hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) is a military explosive that is a common soil and groundwater contaminant at facilities that manufacture, handle, and dispose of munitions. One such facility is the U.S. Department of Energy Pantex Plant, the focus of this research in which the feasibility of in situ bioremediation of contaminated soil in the vadose zone was assessed. A batch technique using ¹⁴C-RDX was developed to investigate the degradation of RDX under aerobic, microaerobic, and anaerobic conditions. In addition, the effect of nutrients (organic carbon and phosphorus) on biodegradation rates was studied. The extent of mineralization was quantified by monitoring the production of ¹⁴CO₂, and RDX biodegradation rates were estimated for each environmental condition. The results showed that RDX degraders were indigenous to the contaminated soil and degraded RDX to a significant extent under anaerobic conditions. Little biotransformation was observed under aerobic conditions. The addition of a biodegradable organic carbon source significantly increased the RDX biodegradation rate. Under appropriate environmental conditions, significant mineralization of RDX also was observed. The half-lives for the degradation of RDX under anaerobic conditions were approximately 60 days and decreased to approximately 40 days with nutrient addition. In contrast, the half-life for aerobic degradation was on the order of 1000 days, with an upper 95% confidence interval approaching infinity.     

Biodegradation of Aliphatic vs. Aromatic Hydrocarbons in Fertilized Arctic Soils

The objectives of this study were to (1) test a simple bioremediation treatment strategy in the Arctic and (2) examine the effect of fertilization on the degradation of aliphatic and aromatic hydrocarbons. The site is a coarse sand pad that once supported fuel storage tanks. Concentrations of diesel-range organics at the beginning of the study (July 1996) ranged from 250 to 860 mg/kg soil. Replicate field plots treated with fertilizer yielded final concentrations of 0, 50, 100, or 200 mg N/kg soil. Soil samples were collected three times during the thaw season and analyzed for physical and chemical properties, microbial populations and activities, and concentrations of semivolatile hydrocarbons. Soil pH and soil-water potentials declined as a result of fertilizer application. Addition of fertilizer significantly increased soil respiration potentials, but not the populations of microorganisms measured. Fertilizer addition also resulted in ∼50% loss of measured aliphatic and aromatic hydrocarbons in surface and subsurface soils. For fertilized plots, hydrocarbon loss was not related to the amount of fertilizer added. Losses of aliphatic hydrocarbons were attributed to biotic processes, whereas losses of aromatic hydrocarbons likely were a result of both biotic and abiotic processes.     

Applicability of Coriolopsis rigida for Biodegradation of Polycyclic Aromatic Hydrocarbons

Laccase was produced by Coriolopsis rigida using barley bran as substrate in solid-state fermentation (SSF) and also by submerged fermentation (SmF). The best results were obtained in SSF with twice the amount of laccase production. Laccase could be produced from repeated batch cultures of SSF over 30 days. The laccase degraded several polycyclic aromatic hydrocarbons (PAHs) in vivo and in vitro. The addition of an effective mediator, 1-hydroxybenzotriazol (50 µM), during in vitro treatment increased the degradation rate.     

Chemical Vapor Intrusion from Soil or Groundwater to Indoor Air: Significance of Unsaturated Zone Biodegradation of Aromatic Hydrocarbons

The soil vapor to indoor air exposure pathway is considered in a wide number of risk-based site management programs. In screening-level assessments of this exposure pathway, models are typically used to estimate the transport of vapors from either subsurface soils or groundwater to indoor air. Published studies indicate that the simple models used to evaluate this exposure pathway often over estimate the impact for aromatic hydrocarbons (e.g., benzene, toluene, ethylbenzene, and xy-lene or BTEX), while showing reasonable agreement for estimates of chlorinated hydrocarbon impacts (e.g., PCE, TCE, DCE). Aerobic biodegradation of the petroleum hydrocarbons is most often attributed as the source of this disparity in the model/ data comparisons. This paper looks at the significance of aerobic biodegradation of aromatic hydrocarbons as part of the assessment of chemical vapor intrusion from soil or groundwater to indoor air. A review of relevant literature summarizing the available field data as well as various modeling approaches that include biodegradation is presented. This is followed by a simple modeling analysis that demonstrates the potential importance of biodegradation in the assessment of the soil vapor to indoor air exposure pathway. The paper concludes with brief discussions of other model considerations that are often not included in simple models but may have a significant impact on the intrusion of vapors into indoor air.     

Biodegradation of Oil Tank Bottom Sludge using Microbial Consortia

We present a rationale for the selection of a microbial consortia specifically adapted to degrade toxic components of oil refinery tank bottom sludge (OTBS). Sources such as polluted soils, petrochemical waste, sludge from refinery-wastewater plants, and others were used to obtain a collection of eight microorganisms, which were individually tested and characterized to analyze their degradative capabilities on different hydrocarbon families. After initial experiments using mixtures of these strains, we developed a consortium consisting of four microorganisms (three bacteria and one yeast) selected in the basis of their cometabolic effects, emulsification properties, colonization of oil components, and degradative capabilities. Although the specific contribution each of the former parameters makes is not clearly understood, the activity of the four-member consortium had a strong impact not only on linear alkane degradation (100%), but also on the degradation of cycloalkanes (85%), branched alkanes (44%), and aromatic and sulphur–aromatic compounds (31–55%). The effectiveness of this consortium was significantly superior to that obtained by individual strains, commercial inocula or an undefined mixture of culturable and non-culturable microorganisms obtained from OTBS-polluted soil. However, results were similar when another consortium of four microorganisms, previously isolated in the same OTBS-polluted soil, was assayed.     

Potential for Aerobic and Anaerobic Biodegradation of Petroleum Hydrocarbons in Boreal Subsurface

We studied the role of aerobic and anaerobic petroleum hydrocarbon degradation at a boreal, light-weight fuel and lubrication oil contaminated site undergoing natural attenuation. At the site, anoxic conditions prevailed with high concentrations of CH4 (up to 25% v/v) and CO2 (up to 18% v/v) in the soil gas throughout the year. Subsurface samples were obtained mainly from the anoxic parts of the site and they represented both the unsaturated and saturated zone. The samples were incubated in microcosms at near in situ conditions (i.e. in situ temperature 8 degrees C, aerobic and anaerobic conditions, no nutrient amendments) resulting in the removal of mineral oil (as determined by gas chromatography) aerobically as well as anaerobically. In the aerobic microcosms on average 31% and 27% of the initial mineral oil was removed during a 3- and 4-month incubation, respectively. In the anaerobic microcosms, on average 44% and 15% of the initial mineral oil was removed during a 12- and 10-month anaerobic incubation, respectively, and e.g. n-alkanes from C11 to C15 were removed. A methane production rate of up to 2.5 microg CH4 h(-1) g(-1) dwt was recorded in these microcosms. In the aerobic as well as anaerobic microcosms, typically 90% of the mineral oil degraded belonged to the mineral oil fraction that eluted from the gas chromatograph after C10 and before C15, while 10% belonged to the fraction that eluted after C15 and before C40. Our results suggest that anaerobic petroleum hydrocarbon degradation, including n-alkane degradation, under methanogenic conditions plays a significant role in the natural attenuation in boreal conditions.