Effect of non-feeding period length on the intermittent operation of UASB reactors treating dairy effluents

Recent environmental concerns have prompted a re-evaluation of conventional management strategies and refueled the search of innovative waste management practices. In this sense, the anaerobic digestion of both fat and the remaining complex organic matter present in dairy wastewaters is attractive, although the continuous operation of high rate anaerobic processes treating this type of wastewaters causes the failure of the process. This work accesses the influence of non-feeding period length on the intermittent operation of mesophilic UASB reactors treating dairy wastewater, in order to allow the biological degradation to catch up with adsorption phenomenon. During the experiments, two UASB reactors were subject to three organic loading rates, ranging from 6 to 12 g(COD) x L(-1) x d(-1), with the same daily load applied to both reactors, each one with a different non-feeding period. Both reactors showed good COD removal efficiencies (87-92%). A material balance for COD in the reactors during the feeding and non-feeding periods showed the importance of the feedless period, which allowed the biomass to degrade substrate that was accumulated during the feeding period. The reactor with the longest non-feeding period had a better performance, which resulted in a higher methane production and adsorption capacity for the same organic load applied with a consequent less accumulation of substrate into the biomass. In addition, both reactors had a stable operation for the organic load of 12 g(COD) x L(-1) x d(-1), which is higher than the maximum applicable load reported in literature for continuous systems (3-6 g(COD) x L(-1) x d(-1)).     

High-rate sulfate reduction at high salinity (up to 90 mS.cm(-1)) in mesophilic UASB reactors

Sulfate reduction in salt-rich wastewaters using unadapted granular sludge was investigated in 0.9 L UASB reactors (pH 7.0 +/- 0.2; hydraulic retention time from 8-14 h) fed with acetate, propionate, or ethanol at organic loading rates up to 10 gCOD x L(-1) x day(-1) and in excess sulfate (COD/SO(4) (2-) of 0.5). High-rate sulfate reduction rates (up to 3.7 gSO(4) (2-) x L(-1).day(-1)) were achieved at salinities exceeding 50 gNaCl.L(-1) and 1 gMgCl(2) x L(-1). Sulfate reduction proceeded at a salinity of up to 70 gNaCl x L(-1) and 1 gMgCl(2) x L(-1) (corresponding to a conductivity of about 85-90 mS x cm(-1)), although at lower rates compared to a conductivity of 60-70 mS x cm(-1). Ethanol as well as propionate were suitable substrates for sulfate reduction, with acetate and sulfide as the end products. The successful high-rate treatment was due to the proliferation of a halotolerant incomplete oxidizing SRB population present in the unadapted inoculum sludge. Bioaugmentation of this sludge with the acetate oxidizing halotolerant SRB Desulfobacter halotolerans was unsuccessful, as the strain washed out from the UASB reactor without colonizing the UASB granules.     

Study of microbial community structures in UASB sludge treating municipal wastewater by denaturing gradient gel electrophoresis of 16S rDNA

The structures of microbial communities in lab-scale upflow anaerobic sludge blanket (UASB) reactors for treating municipal wastewater with different ratios of COD soluble/COD total were studied using denaturing gradient gel electrophoresis (DGGE) of 16S rRNA genes.The microbial structure of the inoculum sludge obtained from a full-scale UASB reactor of treating potato processing wastewater was compared with the structures of sludges collected from three lab-scale UASB reactors after eight months feeding with raw municipal wastewater, with CEPS (chemically enhanced primary sedimentation) pretreated municipal wastewater, and with a synthetic municipal sewage, respectively. Computer-aided numerical analysis of the DGGE fingerprints showed that the bacterial community underwent major changes. The sludges for treating raw and CEPS pretreated wastewater had very similar bacterial and archaeal communities (82%and 96% similarity) but were different from that for treating the synthetic sewage. Hence, despite similar % COD in the particulate form in the synthetic and the real wastewater, the two wastewaters were selected for different microbial communities. Prominent DGGE bands of Bacteria and Archaea were purified and sequenced. The 16S rRNA gene sequences of the dominant archaeal bands found in the inoculum, and UASB sludge fed with raw sewage, CEPS pretreated wastewater, and synthetic sewage were closely associated with Methanosaeta concilii. In the UASB sludge fed with synthetic sewage, another dominant band associated with an uncultured archaeon 39-2 was found together with M. concilii.     

Effect of influent pH and alkalinity on the removal of chlorophenols in sequential anaerobic–aerobic reactors

This study was carried out to determine the effect of influent pH and alkalinity on the performance of sequential UASB and RBC reactors for the removal of 2-CP and 2,4-DCP from two different simulated wastewaters. The performance of methanogens at low (<6.0) to high (>8.0) pH values and at sufficiently high alkalinity (1500–3500 mg/l as CaCO₃) is described in this paper. Sequential reactors were capable of handling wastewaters with influent pH, 5.5–8.5. However, with influent pH 7.0 ± 0.1 UASB reactor showed best performance for 2-CP (99%) and 2,4-DCP (88%) removals. Increase in alkalinity/COD ratio in the influent (>1.1) caused gradual decrease in the chlorophenol removal in UASB reactors. The UASB reactors could not tolerate wastewater with higher alkalinity/COD ratio (2.6) and showed significant deterioration of its performance in terms of chlorophenols removal achieving only 74.7% 2-CP and 60% 2,4-DCP removals, respectively.     

Study of microbial community structures in UASB sludge treating municipal wastewater by denaturing gradient gel electrophoresis of 16S rDNA

The structures of microbial communities in lab-scale upflow anaerobic sludge blanket (UASB) reactors for treating municipal wastewater with different ratios of COD_soluble/ COD_total were studied using denaturing gradient gel electrophoresis (DGGE) of 16S rRNA genes. The microbial structure of the inoculum sludge obtained from a full-scale UASB reactor of treating potato processing wastewater was compared with the structures of sludges collected from three lab-scale UASB reactors after eight months feeding with raw municipal wastewater, with CEPS (chemically enhanced primary sedimentation) pretreated municipal wastewater, and with a synthetic municipal sewage, respectively. Computer-aided numerical analysis of the DGGE fingerprints showed that the bacterial community underwent major changes. The sludges for treating raw and CEPS pretreated wastewater had very similar bacterial and archaeal communities (82% and 96% similarity) but were different from that for treating the synthetic sewage. Hence, despite similar % COD in the particulate form in the synthetic and the real wastewater, the two wastewaters were selected for different microbial communities. Prominent DGGE bands of Bacteria and Archaea were purified and sequenced. The 16S rRNA gene sequences of the dominant archaeal bands found in the inoculum, and UASB sludge fed with raw sewage, CEPS pretreated wastewater, and synthetic sewage were closely associated withMethanosaeta concilii. In the UASB sludge fed with synthetic sewage, another dominant band associated with an uncultured archaeon 39-2 was found together withM. concilii.     

Feasibility studies on the treatment of dairy wastewaters with upflow anaerobic sludge blanket reactors

The feasibility of using upflow anaerobic sludge blanket (UASB) reactors for the treatment of dairy wastewaters was explored. Two types of UASBs were used--one operating on anaerobic sludge granules developed by us from digested cowdung slurry (DCDS) and the other on the granules obtained from the reactors of M/s EID Parry treating sugar industry wastewaters. The reactors were operated at HRT of 3 and 12 h and on COD loading rates ranging from 2.4 kg per m3 of digester volume, per day to 13.5 kg m(-3) d(-1). At the 3 h HRT, the maximum COD reduction in the DCDS-seeded and the industrial sludge-seeded reactors was 95.6% and 96.3%, respectively, better than at 12 h HRT (90% and 92%, respectively). In both the reactors, the maximum, the second best, and the third best COD reduction occurred at the loading rates of 10.8, 8.6 and 7.2 kg m3 d(-1), respectively. At loading rates higher than 10.8 kg, the reactor performance dropped precipitously. Whereas in the first few months the reactors operating on sludge from EID Parry achieved better biodegradation of the waste, compared to the reactors operated on DCDS, the performance of the latter gradually improved and matched with the performance of the former.     

Influence of biogas-induced mixing on granulation in UASB reactors

Studies have been carried out to correlate biogas-induced mixing and granulation in upflow anaerobic sludge blanket (UASB) reactors, treating low-strength as well as high-strength biodegradable wastewaters. A dimensionless granulation index (GI) has been framed taking into account the mixing in sludge bed due to produced biogas. Analysis of full-scale, pilot-scale and lab-scale UASB reactors treating actual wastewaters reveals the significance of biogas-induced mixing, represented by GI, on granulation of biomass in the reactors. For obtaining proper granulation in UASB reactors (percentage granules greater than 50%, w/w), resulting in higher chemical oxygen demand (COD) removal efficiency, it is recommended to maintain GI values in the range of 15,000–57,000.     

Kinetics of anaerobic treatment of slaughterhouse wastewater in batch and upflow anaerobic sludge blanket reactor

The kinetics of anaerobic treatment of slaughterhouse wastewater in batch and upflow anaerobic sludge blanket (UASB) reactors was investigated. Different concentrations of organic matter in slaughterhouse wastewater did not change the first order kinetics of the reaction. In batch digesters, methane and nitrogen production stopped after 30-40, 20-30 h, respectively, and in UASB reactors it was terminated after 30-40 days. The constant of velocity was 3.93 and 0.23 h(-1) respectively, for methane and nitrogen production. The yield coefficient, Yp was 343 and 349 ml CH4 per g of chemical oxygen demand at standard temperature and pressure conditions for batch reactors and UASB reactor, respectively.     

Anaerobic Reactor Design Concepts for the Treatment of Domestic Wastewater

Since the earlier anaerobic treatment systems, the design concepts were improved from classic reactors like septic tanks and anaerobic ponds, to modern high rate reactor configurations like anaerobic filters, UASB, EGSB, fixed film fluidized bed and expanded bed reactors, and others. In this paper, anaerobic reactors are evaluated considering the historical evolution and types of wastewaters. The emphasis is on the potential for application in domestic sewage treatment, particularly in regions with a hot climate. Proper design and operation can result in a high capacity and efficiency of organic matter removal using single anaerobic reactors. Performance comparison of anaerobic treatment systems is presented based mostly on a single but practical parameter, the hydraulic retention time. Combined anaerobic reactor systems as well as combined anaerobic and non-anaerobic systems are also presented.     

Treatment of low strength soluble wastewaters in UASB reactors

Low strength wastewaters can be those with chemical oxygen demand (COD) below 2,000 mg/l. The anaerobic treatment of such wastewaters has not been fully explored so far. The suboptimal reaction rates with low substrate concentrations, and the presence of dissolved oxygen in the influent are regarded as possible constraints. In this study, the treatment of low strength soluble wastewaters containing ethanol or whey was studied in lab-scale upflow anaerobic sludged bed (UASB) reactors at 30°C. The high treatment performance obtained demonstrates that UASB reactors are viable for treating both types of wastewaters at low COD concentrations. The treatment of the ethanol containing wastewater resulted in COD removal efficiencies exceeding 95% at organic loading rates (OLR) between 0.3 to 6.8 g COD/l-d with influent concentrations in the range of 422 to 943 mg COD/l. In the case of the more complex whey containing wastewater, COD removal efficiencies exceeded 86% at OLRs up to 3.9 g COD/l·, as long as the COD influent was above 630 mg/l. Lowering the COD influent resulted in decreased efficiency with sharper decrease at values below 200 mg/l. Acidification instead of methanogenesis was found to be the rate limiting step in the COD removal at low concentrations, which was not the case when treating ethanol. The effect of dissolved oxygen in the influent as a potential danger in anaerobic treatment was investigated in reactors fed with and without dissolved oxygen. Compared with the control reactor, the reactor receiving oxygen showed no detrimental effects in the treatment performance. Thus, the presence of dissolved oxygen in dilute wastewaters is expected to be of minor importance in practice.     

Effect of carbon sources and shock loading on the removal of chlorophenols in sequential anaerobic-aerobic reactors

The effect of carbon sources and shock loadings have been studied using two sets of sequential upflow anaerobic sludge blanket (UASB) and rotating biological contactor (RBC) reactors viz., UASB-I followed by RBC-I and UASB-II followed by RBC-II for the removal of two different priority pollutants, 2-CP and 2,4-DCP present in simulated wastewaters. Sodium formate, sodium propionate, glucose and methanol were used separately as four different carbon sources in the feed as co-substrate. Methanol was found to be the best carbon source for UASB reactors showing 95% 2-CP and 81.1% 2,4-DCP removals. The carbon sources formate and propionate were not found suitable in UASB reactors as only 22.6-46.8% 2-CP and 41.9-42.8% 2,4-DCP removals were observed. With glucose as carbon source 93.7% 2-CP and 79.6% 2,4-DCP removals were observed in UASB reactors. For all the four carbon sources more than 97.6% 2-CP and 99.7% 2,4-DCP removals were observed in sequential reactors. Although all the four carbon sources could not serve as good carbon source for UASB reactor alone but could be successfully used by the sequential reactors for the removal of chlorophenols. The Performance of sequential reactors was also evaluated at five different chlorophenolic shock loadings. During shock loading study the concentration of chlorophenols in the wastewaters was increased to 45, 60, 75, 90 and 105 mg/l as compared to the normal feed containing 30 mg/l 2-CP or 2,4-DCP. During shock loading study complete removal of 2-CP and more than 99.6% removal of 2,4-DCP was observed in sequential reactors. Sequential reactors successfully withstood all the shock loadings and produced high quality effluents.     

Anaerobic treatment of the municipal wastewater under psychrophilic conditions

The article discusses possibilities of municipal wastewater treatment in various types of anaerobic reactors (UASB, UAF, AnSBR). The temperature during corresponding laboratory experiments varied between 9–23?°C. Real wastewater from WWTP Bratislava-Petr?alka and synthetic substrate were used in the experiments. The HRT values for reactors were found to be 10–46?h. Treatment of municipal wastewater with the AnSBR and UAF system has shown more positive results in laboratory scale studies then the UASB system. The mean removal efficiency of COD depended on the type of anaerobic reactor, temperature, used HRT and was found between 37–48% (UASB), 56–88% (AnSBR) and 46–90% (UAF).     

对处理不同废水的几种厌氧消化器生物量中优势产甲烷菌的观察

The biomass taken from AF, ABR, and UASB digesters treating municipal wastewater, swine waste and molassese stillage wastewater, municipal and molassese stillage wastewater respectively, were observed by light, epifluorescence microscope and scanning electron microscope. The prevalent methanogens in these digesters were Methanothrix. Exception for ABR carried out to treat swine waste, Methanosarcina with three forms of aggregations, cysts, and granules were presented in other digesters. A suggestion can be made that reactors with packing materials, such as, anaerobic filters, anaerobic contact beds and two-phase methanation digesters can be used to accumulate Methanosarcina due to their morphological, mu max, and Ks characteristics, in order to increase the wastewater treatment efficiency further.     

Statistical modeling and optimization of biomass granulation and COD removal in UASB reactors treating low strength wastewaters

The aim of this work was to study the influence of influent chemical oxygen demand (COD), upflow velocity of wastewater, and cationic polymer additives in inoculum, on biomass granulation and COD removal efficiency in upflow anaerobic sludge blanket (UASB) reactor for treating low strength wastewater. Statistical models were formulated based on these three variables to optimize the biomass granulation and COD removal efficiency in UASB reactors using a two-level, full factorial design. For the thick inoculum used in this study, having suspended solids (SS) >80 g/l and volatile suspended solids (VSS) to SS ratio <0.3, cationic polymer additives in the inoculum showed adverse effect on biomass granulation and COD removal efficiency. It is concluded that for such thick inoculum, granulation can be obtained while treating low strength wastewaters in UASB reactor by selecting proper combination of influent COD and liquid upflow velocity so as to represent the organic loading rate (OLR) greater than 1.0 kg COD/m(3) d. Validation of model predictions for treatment of synthetic wastewater and actual sewage reveals the efficacy of these models for enhancing granulation and COD removal efficiency.     

Removal of chlorophenols in sequential anaerobic-aerobic reactors

Combination of upflow anaerobic sludge blanket (UASB) and aerobic rotating biological contactor (RBC) reactors having higher biomass concentration and higher sludge retention time (SRT) was applied for the sequential treatment of priority pollutant chlorophenol containing wastewater. Target compounds 2-chlorophenol (2-CP) and 2,4-dichlorophenol (2,4-DCP) present in two simulated wastewaters at a concentration of 30 mg/l each individually were sequentially treated in continuous mode by combined UASB-I, RBC-I and combined UASB-II, RBC-II reactors, respectively after the acclimation of their biomass with the corresponding chlorophenol. Reactor combinations took 190 and 215 days for acclimation with 30 mg/l of 2-CP and 2,4-DCP respectively. Hydraulic retention time (HRT) studies showed that 12h HRT of UASB-I and 23 h HRT of RBC-I as well as 12h HRT of UASB-II and 28.8h HRT of RBC-II were the optimum combinations for the treatment of simulated wastewater containing 2-CP and 2,4-DCP respectively. Optimum HRT combinations produced 2-CP and 2,4-DCP effluent having corresponding chlorophenol concentration of below detectable limit (BDL) and 0.1 mg/l respectively. Half velocity coefficients (Ks) for 2-CP and 2,4-DCP biodegradation in UASB reactors were determined to be 5.07 mg 2-CP/l and 6.49 mg 2,4-DCP/l. Optimum ratio of substrate (chlorophenol): co-substrate (sodium acetate) was 1:100.     

Introduction of a de novo bioremediation ability, aryl reductive dechlorination, into anaerobic granular sludge by inoculation of sludge with Desulfomonile tiedjei.

Methanogenic upflow anaerobic granular-sludge blanket (UASB) reactors treat wastewaters at a high rate while simultaneously producing a useful product, methane; however, recalcitrant environmental pollutants may not be degraded. To impart 3-chlorobenzoate (3-CB)-dechlorinating ability to UASB reactors, we inoculated granular sludge in UASB reactors with either a pure culture of Desulfomonile tiedjei (a 3-CB-dechlorinating anaerobe) or a three-member consortium consisting of D. tiejei, a benzoate degrader, and an H2-utilizing methanogen. No degradation occurred in an uninoculated control reactor which was started with the same granular sludge, but inoculated reactors and granules from the inoculated UASB systems rapidly transformed 3-CB (54 mumol/day/g of granule biomass). After several months at a hydraulic retention time of 0.5 day, much shorter than the generation time of D. tiedjei, the reactors still dechlorinated 3-CB. This indicated that the bacteria were immobilized in the reactor granules, and by using an antibody probe for D. tiedjei, we demonstrated that this microorganism had colonized the sludge granules. These results represent the first addition of a pure culture or a defined microbial mixture to a viable waste treatment process to introduce a specific de novo degradative pathway into a granular-sludge consortium.     

Introduction of a de novo bioremediation ability, aryl reductive dechlorination, into anaerobic granular sludge by inoculation of sludge with Desulfomonile tiedjei.

Methanogenic upflow anaerobic granular-sludge blanket (UASB) reactors treat wastewaters at a high rate while simultaneously producing a useful product, methane; however, recalcitrant environmental pollutants may not be degraded. To impart 3-chlorobenzoate (3-CB)-dechlorinating ability to UASB reactors, we inoculated granular sludge in UASB reactors with either a pure culture of Desulfomonile tiedjei (a 3-CB-dechlorinating anaerobe) or a three-member consortium consisting of D. tiejei, a benzoate degrader, and an H2-utilizing methanogen. No degradation occurred in an uninoculated control reactor which was started with the same granular sludge, but inoculated reactors and granules from the inoculated UASB systems rapidly transformed 3-CB (54 mumol/day/g of granule biomass). After several months at a hydraulic retention time of 0.5 day, much shorter than the generation time of D. tiedjei, the reactors still dechlorinated 3-CB. This indicated that the bacteria were immobilized in the reactor granules, and by using an antibody probe for D. tiedjei, we demonstrated that this microorganism had colonized the sludge granules. These results represent the first addition of a pure culture or a defined microbial mixture to a viable waste treatment process to introduce a specific de novo degradative pathway into a granular-sludge consortium.     

Study of microbial community structures in UASB sludge treating municipal wastewater by denaturing gradient gel electrophoresis of 16S rDNA

The structures of microbial communities in lab-scale upflow anaerobic sludge blanket (UASB) reactors for treating municipal wastewater with different ratios of COD soluble/ COD total were studied using denaturing gradient gel electrophoresis (DGGE) of 16S rRNA genes. The microbial structure of the inoculum sludge obtained from a full-scale UASB reactor of treating potato processing wastewater was compared with the structures of sludges collected from three lab-scale UASB reactors after eight months feeding with raw municipal wastewater, with CEPS (chemically enhanced primary sedimentation) pretreated municipal wastewater, and with a synthetic municipal sewage, respectively. Computer-aided numerical analysis of the DGGE fingerprints showed that the bacterial community underwent major changes. The sludges for treating raw and CEPS pretreated wastewater had very similar bacterial and archaeal communities (82% and 96% similarity) but were different from that for treating the synthetic sewage. Hence, despite     

Nitrogen removal from animal waste treatment water by anammox enrichment

The aim of this work was to examine the applicability of the anaerobic ammonium oxidation (anammox) process to three kinds of low BOD/N ratio wastewaters from animal waste treatment processes in batch mode. A rapid decrease of NO(2)(-) and NH(4)(+) was observed during incubation with wastewaters from AS and UASB/trickling filter and their corresponding control artificial wastewaters. This nitrogen removal resulted from the anammox reaction, because the ratio of removed NO(2)(-) and NH(4)(+) was close to the theoretical ratio of the anammox reaction. Comparison of the inorganic nitrogen removal rate of the actual wastewater and that of control artificial wastewater showed that these two kinds of wastewater were very suitable for anammox treatment. Incubation with wastewater from RW did not show a clear anammox reaction; however, diluting it by half enabled the reaction, suggesting the presence of an inhibitory factor. This study showed that the three kinds of wastewater from animal waste treatment processes were suitable for anammox treatment.     

Thermophilic (55-65 degrees C) and extreme thermophilic (70-80 degrees C) sulfate reduction in methanol and formate-fed UASB reactors

The feasibility of thermophilic (55-65 degrees C) and extreme thermophilic (70-80 degrees C) sulfate-reducing processes was investigated in three lab-scale upflow anaerobic sludge bed (UASB) reactors fed with either methanol or formate as the sole substrates and inoculated with mesophilic granular sludge previously not exposed to high temperatures. Full methanol and formate degradation at temperatures up to, respectively, 70 and 75 degrees C, were achieved when operating UASB reactors fed with sulfate rich (COD/SO4(2-)=0.5) synthetic wastewater. Methane-producing archaea (MPA) outcompeted sulfate-reducing bacteria (SRB) in the formate-fed UASB reactor at all temperatures tested (65-75 degrees C). In contrast, SRB outcompeted MPA in methanol-fed UASB reactors at temperatures equal to or exceeding 65 degrees C, whereas strong competition between SRB and MPA was observed in these reactors at 55 degrees C. A short-term (5 days) temperature increase from 55 to 65 degrees C was an effective strategy to suppress methanogenesis in methanol-fed sulfidogenic UASB reactors operated at 55 degrees C. Methanol was found to be a suitable electron donor for sulfate-reducing processes at a maximal temperature of 70 degrees C, with sulfide as the sole mineralization product of methanol degradation at that temperature.