Enzymatic hydrolysis of chitosan films in water and physiological solution

It was shown that the processes of enzymatic hydrolysis of chitosan in aqueous acetic acid and on the surface of chitosan films in a solution of hyaluronidase in acetic acid are described by uniform kinetic constants. Kinetic parameters of enzymatic hydrolysis of the chitosan film samples in water and in physiological solution (Ringer–Locke’s solution) were determined. It was found that the introduction of medicinal agents and low-molecular-weight electrolytes to a chitosan-based film material reduces the rate of enzymatic hydrolysis of the films, which may indicate a possible increase in their service life when used on the wound surface.     

Structural effects on enzymatic degradabilities for poly[(R)-3-hydroxybutyric acid] and its copolymers.

Poly[(R)-3-hydroxybutyric acid] and its copolymers were prepared by biosynthetic and chemosynthetic methods. The films of polyesters were prepared by both the solution-cast and melt-crystallized techniques. The enzymatic degradation of polyester films was carried out at 37 degrees C in an aqueous solution (pH 7.4) of PHB depolymerase from Alcaligenes faecalis. The rate of enzymatic erosion on the solution-cast films increased markedly with an increase in the fraction of second monomer units up to 10-20 mol% to reach a maximum value followed by a decrease in the erosion rate. Analysis of the water-soluble products liberated during the enzymatic degradation of polyester films showed the formation of a mixture of monomers and oligomers of (R)-3HB and hydroxyalkanoic acids units, suggesting that the active site of PHB depolymerase recognizes at least three monomeric units as substrate for the hydrolysis of ester bonds in a polymer chain. The rate of enzymatic erosion of melt-crystallized polyester films decreased with an increase in crystallinity. PHB depolymerase predominantly hydrolyzed the polymer chains in the amorphous phase and subsequently eroded crystalline phase. In addition, the enzymatic degradation of crystalline phase by PHB depolymerase progressed from the edges of crystalline lamellar stacks. The enzymatic erosion rate of crystalline phase in polyester films decreased with an increase in the lamellar thickness.     

Enzymatic, alkaline, and autocatalytic degradation of poly(L-lactic acid): effects of biaxial orientation

The hydrolytic degradation of biaxially oriented and de-oriented (melt-crystallized) poly(l-lactic acid) (PLLA) films was investigated in Tris-HCl-buffered solution (pH 8.6) with proteinase K, alkaline solution, and phosphate-buffered solution (pH 7.4) by the use of gravimetry, gel permeation chromatography, differential scanning calorimetry, and scanning electron microscopy. Biaxial orientation disturbed the proteinase K-catalyzed enzymatic degradation of PLLA films and the effects of biaxial orientation overcame those of crystallinity. The former may be due to the fact the enzyme cannot attach to the extended (strained) chains in the amorphous regions of the biaxially oriented PLLA film or cannot catalyze the cleavage of the strained chains. Another probable cause is that the enzyme can act only at the film surface of the biaxially oriented PLLA film, in marked contrast with the case of the de-oriented PLLA films where enzymatic degradation can proceed beneath the spherulitic crystalline residues. The effects of biaxial orientation on the alkaline and autocatalytic degradation of the PLLA films were insignificant for the periods studied here. The crystallinity rather than the biaxial orientation seems to determine the alkaline and autocatalytic degradation rates of the PLLA films. The accumulation of crystalline residues formed as a result of selective cleavage and removal of the amorphous chains was observed for the de-oriented PLLA films, but not for the biaxially oriented PLLA film, when degraded in the presence of proteinase K. This means the facile release of formed crystalline residues from the surface of the biaxially oriented PLLA film during enzymatic degradation, due to the fact that the crystalline regions of the biaxially oriented PLLA film were oriented with their c axis parallel to the film surface.     

Photocurable liquid biodegradable copolymers: in vitro hydrolytic degradation behaviors of photocured films of coumarin-endcapped poly(epsilon-caprolactone-co-trimethylene carbonate)

Coumarin-endcapped tetrabranched liquid copolymers composed of epsilon-caprolactone and trimethylene carbonate (TMC), prepared using pentaerythritol or four-branched poly(ethylene glycol) (PEG) as an initiator, were ultraviolet irradiated to produce photocured solid biodegradable copolymers. The hydrolytic degradation behaviors of photocured films were determined from the weight loss of the films. The initial hydrolysis rate (determined for up to 24 h using a quartz crystal microbalance) was enhanced with aqueous solutions of higher pH. The hydrolysis rate in the early period of immersion was increased with an increase in TMC content, whereas that in the later period (week order) decreased with a increase in TMC content. This inverse relation of composition dependence on the hydrolysis rate between the early and late periods was discussed. Topological measurements using scanning electron microscopy and atomic force microscopy as well as depth profiles of the fluorescein-stained hydrolyzed layer showed that for the pentaerythritol-initiated copolymer, irrespective of copolymer composition, hydrolysis occurred at surface regions and surface erosion proceeded with immersion time. For PEG-based copolymers, both surface erosion and bulk degradation occurred simultaneously. The hydrolyzed surfaces became highly wettable with water and exhibited noncell adhesivity.     

Change of surface structure of poly(3-hydroxybutyrate) film upon enzymatic hydrolysis by PHB depolymerase

The change in the surface structure of poly[(R)-3-hydroxybutyrate] [PHB] films upon the enzymatic hydrolysis was analyzed by attenuated total reflection infrared [ATR/IR] spectrometry. As enzymes, PHB depolymerases isolated from Ralstonia pickettii T1 and Pseudomonas stutzeri were used. By curve decomposition of the carbonyl stretching band of ATR/IR spectra, the change in the surface crystallinity of PHB films by exposure to buffer containing 0, 1, and 4 microg of PHB depolymerases was estimated. It has been widely believed that the enzymatic hydrolysis first occurs in the amorphous phase, followed by the degradation in the crystalline phase, and extracellular PHB depolymerase can degrade only polymer chains in the surface layer of the film. Therefore, the surface crystallinity had been expected to increase upon the enzymatic degradation. However, the results were contrary to this expectation. The surface crystallinity was decreased by the enzymatic attack. Because ATR/IR spectrometry is sensitive to a small change in molecular structure of the sample surface, the decrease in the crystallinity shown by ATR/IR experiments probably does not indicate the complete loss of regularity of the crystalline phase. Because the chains at crystalline surface are more mobile than those inside the crystals, the C=O band for crystalline surface may appear at a position similar to those of the amorphous or interfacial phase in ATR/IR spectra of PHB. Only the chains inside the crystals may contribute to the C=O band of the crystalline phase. Thus, we rather suppose that the decrease in the crystalline peak of the ATR/IR spectra reflects the change in chain mobility or the increase of crystalline surface area by cracking of lamellas at the surface layers of PHB films or both.     

Structural effects of terminal groups on nonenzymatic and enzymatic degradations of end-capped poly(L-lactide)

Poly(L-lactide) (PLLA) with various alkyl ester chain end groups were synthesized by ring-opening polymerization of L-lactide in the presence of zinc alkoxide as a catalyst. The structural effect of chain end groups on the rate of enzymatic and nonenzymatic degradations for amorphous films of PLLA were investigated at 37 degrees C in a Tris-HCl buffer solution (pH 8.6) with proteinase K and at 60 degrees C in a phosphate buffer solution (pH 7.4), respectively. The rate of enzymatic degradation for PLLA films was dependent on the carbon numbers of alkyl ester chain end groups, and the rates of PLLA samples with dodecyl (C12), tridecyl (C13), and tetracocyl (C14) ester end groups were much lower than those of the other samples. The surface morphologies of PLLA films after enzymatic degradation were characterized by scanning electron microscopy. After the enzymatic degradation, non-end-capped PLLA, PLLA with methyl (C1) and hexyl (C6) ester chain ends, were degraded homogeneously by proteinase K and the film surface was very smooth. In contrast, the PLLA with alkyl ester chain ends of carbon numbers over 12 were degraded heterogeneously by the enzyme, and the sponge-like network structure was formed on the film surface. These results indicated that the long alkyl ester groups at the chain ends of PLLA molecules aggregated in the amorphous films and the erosion rate was depressed due to the coverage of the aggregated terminal groups on the film surface. For the nonenzymatic degradation, the molecular weight of non-end-capped PLLA was remarkably decreased with progress of degradation. In contrast, the molecular weight of the end-capped PLLA gradually reduced at the initial stage of degradation and then the rate of degradation was accelerated. The decreases of molecular weight of PLLA by autocatalyzed degradation were retarded by the capping of carboxyl chain ends.     

A dual enzyme system composed of a polyester hydrolase and a carboxylesterase enhances the biocatalytic degradation of polyethylene terephthalate films

TfCut2 from Thermobifida fusca KW3 and the metagenome‐derived LC‐cutinase are bacterial polyester hydrolases capable of efficiently degrading polyethylene terephthalate (PET) films. Since the enzymatic PET hydrolysis is inhibited by the degradation intermediate mono‐(2‐hydroxyethyl) terephthalate (MHET), a dual enzyme system consisting of a polyester hydrolase and the immobilized carboxylesterase TfCa from Thermobifida fusca KW3 was employed for the hydrolysis of PET films at 60°C. HPLC analysis of the reaction products obtained after 24 h of hydrolysis showed an increased amount of soluble products with a lower proportion of MHET in the presence of the immobilized TfCa. The results indicated a continuous hydrolysis of the inhibitory MHET by the immobilized TfCa and demonstrated its advantage as a second biocatalyst in combination with a polyester hydrolase for an efficient degradation oft PET films. The dual enzyme system with LC‐cutinase produced a 2.4‐fold higher amount of degradation products compared to TfCut2 after a reaction time of 24 h confirming the superior activity of his polyester hydrolase against PET films.     

Effect of water on the surface molecular mobility of poly(lactide) thin films: an atomic force microscopy study

Physical properties associated with molecular mobility on the surface of thin films with 300 nm thickness for poly(lactide)s (PLAs) were studied under vacuum conditions as well as under aqueous conditions by using friction force mode atomic force microscopy (AFM). Two types of PLAs were applied for the experimental samples as uncrystallizable PLA (uc-PLA) and crystallizable PLA (c-PLA). The friction force on the surface of thin films was measured as a function of temperature to assess the surface molecular mobility both under vacuum and under aqueous conditions. A lower glass-transition temperature of the uc-PLA surface in water was detected than that under vacuum conditions. In the case of the c-PLA thin film, change in friction force was detected at a lower temperature under aqueous conditions than in vacuo. A morphological change was observed in the c-PLA thin film during heating process from room temperature to 100 degrees C by temperature-controlled AFM. The surface of the c-PLA thin film became rough due to the cold crystallization, and the crystallization of c-PLA molecules in water took place at a lower temperature than in vacuo. These friction force measurements and AFM observations suggest that molecular motion on the surface of the both uc- and c-PLA thin films is enhanced in the presence of water molecules. In addition, in situ AFM observation of the enzymatic degradation process for the c-PLA thin film crystallized at 160 degrees C was carried out in buffer solution containing proteinase K at room temperature. The amorphous region around the hexagonal crystal was eroded within 15 min. It has been suggested that the adsorption of water molecules on the PLA film surface enhances the surface molecular mobility of the glassy amorphous region of PLA and induces the enzymatic hydrolysis by proteinase K.     

Application of infrared spectroscopy (attenuated total reflection) for monitoring enzymatic activity on substrate films

Infrared film analysis, a method based on infrared spectroscopy in the mode of attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), is demonstrated as a novel analytical method for monitoring enzymatic activity on surface-attached substrate films in the mid infrared range (400-4000 cm(-1)). The ATR-FTIR technique is sensitive to molecules within a distance of approximately 1 microm from the ATR sampling unit surface (a 7 cm(2) hydrophobic ZnSe crystal). Applying a 0.2-0.3 microm thick film on the ATR unit surface, any chemical changes within this film as well as at the interface can be continuously monitored, even having an aqueous phase on top of the film. Infrared film analysis is considered especially useful for studying detergent enzymes, which act on surface bound films consisting of food component like vegetable oils (triacylglycerols) and carbohydrates (e.g. starch). Experimental data are presented for hydrolysis of a triacylglycerol film (triolein) by use of a triacylglycerol lipase (cutinase), and starch film degradation by use of an alpha-amylase.     

Phase structure and enzymatic degradation of poly(L-lactide)/atactic poly(3-hydroxybutyrate) blends: an atomic force microscopy study

Phase structures and enzymatic degradation of poly(l-lactide) (PLLA)/atactic poly(3-hydroxybutyrate) (ata-PHB) blends with different compositions were characterized by using atomic force microscopy (AFM). Differential scanning calorimetry (DSC) thermograms of PLLA/ata-PHB blends with different compositions showed two glass transition temperatures, indicating that the PLLA/ata-PHB blends are immiscible in the melt. Surface morphologies of the thin films for PLLA/ata-PHB blends were determined by AFM. Phase separated morphology was recognized from the AFM topography and phase images. The domain size of the components was dependent on the blend ratio. Enzymatic degradation of the PLLA/ata-PHB blends was performed by using both PHB depolymerase and proteinase K. Either PLLA or ata-PHB domains were eroded depending on the kinds of enzyme. Surface morphologies after enzymatic degradation have revealed the phase structure along the depth direction. Enzymatic adsorption of PHB depolymerase was examined on the surface of PLLA/ata-PHB blends. The enzyme molecules were found on both domains of the binary blends. The larger number of enzyme molecules was found on the PLLA domains relative to those on the ata-PHB domains, suggesting the higher affinity of the enzyme against PLLA domain.     

Evidence for selective hydrolysis of aliphatic copolyesters induced by lipase catalysis

High molar mass random poly(butylene succinate-co-butylene sebacate), P(BS-co-BSe), and poly(butylene succinate-co-butylene adipate), P(BS-co-BA), with different composition, were synthesized and subjected to enzymatic hydrolysis by Lipase from Mucor miehei or from Rhizopus arrhizus. The enzymatic hydrolysis of P(BS-co-BSe)s and P(BS-co-BA)s films produced a mixture of water-soluble monomers and co-oligomers that were separated and identified by on-line high performance liquid chromatography/electrospray ionization mass spectrometry (HPLC/ESI-MS). Optimization of the HPLC analysis allowed the separation of isobar co-oligomers, differing only for the co-monomers sequence. Oligomers with the same monomer composition and molar mass but different sequence were identified by HPLC/ESI-MS-MS on-line analysis. The results obtained show a preferential hydrolytic cleavage induced by the lipases used. In particular, these enzymes prefer cleaving sebacic ester bonds in P(BS-co-BSe) copolymers, whereas succinic ester bonds appear to be hydrolyzed faster than adipic ester bonds in P(BS-co-BA) copolyesters. 1H NMR analysis further substantiates these findings. The primary products generated by lipase hydrolysis of polyester films underwent further degradation at longer reaction times. The HPLC/ESI-MS analysis of these mixtures at various times provided the first evidence that lipase catalysis is active also in water solution, a hydrophobic effect induced by the aliphatic units of these polyesters.     

Branched poly(lactide) synthesized by enzymatic polymerization: effects of molecular branches and stereochemistry on enzymatic degradation and alkaline hydrolysis

In this article the effects of the number of molecular branches (chain ends) and the stereochemistry of poly(lactide)s (PLAs) on the enzymatic degradation and alkaline hydrolysis are studied. Various linear and branched PLAs were synthesized using lipase PS (Pseudomonas fluorescens)-catalyzed ring-opening polymerization (ROP) of lactide monomers having different stereochemistries (L-lactide, D-lactide, and D,L-lactide). Five different alcohols were used as initiators for the ROP, and the monomer-to-initiator molar feed ratio was varied from 10 to 100 and 1000 for each branch in the polymer architecture. The properties of branched PLAs that would affect the enzymatic and alkaline degradations, i.e., the glass transition temperature, the melting temperature, the melting enthalpy, and the advancing contact angle, were determined. The PLA films were degraded using proteinase K or 1.0 M NaOH solution, and the weight loss and changes in the number average molecular weight (Mn) of the polymer were studied during 12 h of degradation. The results suggest that an increase in the number of molecular branches of branched PLAs enhances its enzymatic degradability and alkali hydrolyzability. Moreover, the change in Mn of the branched poly(L-lactide) (PLLA) by alkaline hydrolysis indicated that the decrease in Mn was in the first place dependent on the number of molecular branches and thereafter on the length of the molecular branch of branched PLA. The branched PLLA, poly(D-lactide) (PDLA), and poly(D,L-lactide) (PDLLA) differed in weight loss and change in Mn of the PLA segment during the enzymatic degradation. It is suggested that the branched PDLLA was degraded preferentially by proteinase K.     

Effect of Cephtriaxone and Cephtasidim Antibiotics on Enzymatic Hydrolysis of Chitosan-Based Pellicular Materials

Enzymatic hydrolysis of chitosan-based films supplemented with cephtasidim and cephtriaxone antibiotics on a substrate saturated with water, diluted acetic acid, or Ringer-Locke physiological saline was studied. Supplementation with antibiotics having the chemical structure of low molecular weight salts reduced the rate of enzymatic hydrolysis of chitosan regardless of the medium used. The decrease was related to the suppression of polyelectrolyte swelling of the polycation rather than enzyme inhibition. The addition of antibiotics to chitosan films can apparently be considered an approach to directed reduction of the film enzymatic hydrolysis rates, which may contribute to an increase in film lifetime on the wound surface.     

Ultrathin chitin films for nanocomposites and biosensors

Chitin is the second most abundant biopolymer and insight into its natural synthesis, enzymatic degradation, and chemical interactions with other biopolymers is important for bioengineering with this renewable resource. This work is the first report of smooth, homogeneous, ultrathin chitin films, opening the door to surface studies of binding interactions, adsorption kinetics, and enzymatic degradation. The chitin films were formed by spincoating trimethylsilyl chitin onto gold or silica substrates, followed by regeneration to a chitin film. Infrared and X-ray photoelectron spectroscopy, X-ray diffraction, ellipsometry, and atomic force microscopy were used to confirm the formation of smooth, homogeneous, and amorphous chitin thin films. Quartz crystal microbalance with dissipation monitoring (QCM-D) solvent exchange experiments showed these films swelled with 49% water by mass. The utility of these chitin films as biosensors was evident from QCM-D and surface plasmon resonance studies that revealed the adsorption of a bovine serum albumin monolayer.     

Novel biodegradable aliphatic poly(butylene succinate-co-cyclic carbonate)s bearing functionalizable carbonate building blocks: II. Enzymatic biodegradation and in vitro biocompatibility assay

In a previous study, we have reported chemical synthesis of novel aliphatic poly(butylene succinate-co-cyclic carbonate) P(BS-co-CC)s bearing various functionalizable carbonate building blocks, and this work will continue to present our new studies on their enzymatic degradation and in vitro cell biocompatibility assay. First, enzymatic degradation of the novel P(BS-co-CC) film samples was investigated with two enzymes of lipase B Candida Antartic (Novozyme 435) and lipase Porcine Pancreas PPL, and it was revealed that copolymerizing linear poly(butylene succinate) PBS with a functionalizable carbonate building block could remarkably accelerate the enzymatic degradation of a synthesized product P(BS-co-CC), and its biodegradation behavior was found to strongly depend on the overall impacts of several important factors as the cyclic carbonate (CC) comonomer structure and molar content, molar mass, thermal characteristics, morphology, the enzyme-substrate specificity, and so forth. Further, the biodegraded residual film samples and water-soluble enzymatic degradation products were allowed to be analyzed by means of proton nuclear magnetic resonance (1H NMR), gel permeation chromatograph (GPC), differential scanning calorimeter (DSC), attenuated total reflection FTIR (ATR-FTIR), scanning electron microscope (SEM), and liquid chromatograph-mass spectrometry (LC-MS). On the experimental evidences, an exo-type mechanism of enzymatic chain hydrolysis preferentially occurring in the noncrystalline domains was suggested for the synthesized new P(BS-co-CC) film samples. With regard to their cell biocompatibilities, an assay with NIH 3T3 mouse fibroblast cell was conducted using the novel synthesized P(BS-co-CC) films as substrates with respect to the cell adhesion and proliferation, and these new biodegradable P(BS-co-CC) samples were found to exhibit as low cell toxicity as the PLLA control, particularly the two samples of poly(butylene succinate-co-18.7 mol % dimethyl trimethylene carbonate) P(BS-co-18.7 mol % DMTMC) and poly(butylene succinate-co-21.9 mol % 5-benzyloxy trimethylene carbonate) P(BS-co-21.9 mol % BTMC) were interestingly found to show much better cell biocompatibilities than the PLLA reference.     

Interdependence between lignocellulosic biomasses,enzymatic hydrolysis and yeast cell factories in biorefineries

Biorefineries have a pivotal role in the bioeconomy scenario for the transition from fossil-based processes towards more sustainable ones relying on renewable resources. Lignocellulose is a prominent feedstock since its abundance and relatively low cost. Microorganisms are often protagonists of biorefineries, as they contribute both to the enzymatic degradation of lignocellulose complex polymers and to the fermentative conversion of the hydrolyzed biomasses into fine and bulk chemicals. Enzymes have therefore become crucial for the development of sustainable biorefineries, being able to provide nutrients to cells from lignocellulose. Enzymatic hydrolysis can be performed by a portfolio of natural enzymes that degrade lignocellulose, often combined into cocktails. As enzymes can be deployed in different operative settings, such as separate hydrolysis and fermentation (SHF) or simultaneous saccharification and fermentation (SSF), their characteristics need to be combined with microbial ones to maximize the process. We therefore reviewed how the optimization of lignocellulose enzymatic hydrolysis can ameliorate bioethanol production when Saccharomyces cerevisiae is used as cell factory. Expanding beyond biofuels, enzymatic cocktail optimization can also be pivotal to unlock the potential of non-Saccharomyces yeasts, which, thanks to broader substrate utilization, inhibitor resistance and peculiar metabolism, can widen the array of feedstocks and products of biorefineries.     

Structural changes of corn stover lignin during acid pretreatment

In this study, raw corn stover was subjected to dilute acid pretreatments over a range of severities under conditions similar to those identified by the National Renewable Energy Laboratory (NREL) in their techno-economic analysis of biochemical conversion of corn stover to ethanol. The pretreated corn stover then underwent enzymatic hydrolysis with yields above 70?% at moderate enzyme loading conditions. The enzyme exhausted lignin residues were characterized by (31)P NMR spectroscopy and functional moieties quantified and correlated to enzymatic hydrolysis yields. Results from this study indicated that both xylan solubilization and lignin degradation are important for improving the enzyme accessibility and digestibility of dilute acid pretreated corn stover. At lower pretreatment temperatures, there is a good correlation between xylan solubilization and cellulose accessibility. At higher pretreatment temperatures, lignin degradation correlated better with cellulose accessibility, represented by the increase in phenolic groups. During acid pretreatment, the ratio of syringyl/guaiacyl functional groups also gradually changed from less than 1 to greater than 1 with the increase in pretreatment temperature. This implies that more syringyl units are released from lignin depolymerization of aryl ether linkages than guaiacyl units. The condensed phenolic units are also correlated with the increase in pretreatment temperature up to 180?°C, beyond which point condensation reactions may overtake the hydrolysis of aryl ether linkages as the dominant reactions of lignin, thus leading to decreased cellulose accessibility.     

The effects of four different pretreatments on enzymatic hydrolysis of sweet sorghum bagasse

Four pretreatment processes including ionic liquids, steam explosion, lime, and dilute acid were used for enzymatic hydrolysis of sweet sorghum bagasse. Compared with the other three pretreatment approaches, steam-explosion pretreatment showed the greatest improvement on enzymatic hydrolysis of the bagasse. The maximum conversion of cellulose and the concentration of glucose obtained from enzymatic hydrolysis of steam explosion bagasse reached 70% and 25 g/L, respectively, which were both 2.5 times higher than those of the control (27% and 11 g/L). The results based on the analysis of SEM photos, FTIR, XRD and NMR detection suggested that both the reduction of crystallite size of cellulose and cellulose degradation from the Iα and Iβ to the Fibril surface cellulose and amorphous cellulose were critical for enzymatic hydrolysis. These pretreatments disrupted the crystal structure of cellulose and increased the available surface area, which made the cellulose better accessible for enzymatic hydrolysis.     

Synthesis and properties of malic acid-containing functional polymers.

Poly-L-lactides containing beta-alkyl alpha-malate-units were prepared by ring-opening copolymerizations of L-lactide with 3-(s)-[(benzyloxycarbonyl)methyl]- (BMD) and 3-(s)-[(dodecyloxycarbonyl)methyl]-1,4-dioxane-2,5-diones (DMD). The solution-cast films of these copolymers were alkali-treated to form a carboxyl-functionalized surface on which cell-binding Arg-Gly-Asp tripeptide (RGD) was immobilized with dicyclohexylcarbodiimide as coupling agent. For the copolymer of L-lactide and BMD the benzyl groups were removed by catalytic hydrogenolysis to obtain a fully carboxyl-functionalized copolymer (PLGM), and RGD was immobilized on the surface of its cast film. All the RGD-immobilized films thus prepared exhibited improved cell attachment compared with the original films. The cell attachment increased with increasing amount of immobilized RGD, which depended on the composition of the alpha-malate units in the copolymer. The RGD-immobilized PLGM films were degraded rapidly during the cell culture, while the RGD-immobilized films of the beta-alkyl alpha-malate-containing polymers survived the cell culture with little degradation. The rate of hydrolysis increased with increasing content of alpha-malate units for both series, depending on the structure of the protecting groups of the beta-carboxyl. These results suggest that the RGD-immobilized polymers could be a new class of functional bioresorbable polymer having improved cell-attachment and adjustable hydrolysis rate.     

Crystalline-structure-dependent enzymatic degradation of polymorphic poly(3-hydroxypropionate)

The crystalline structure dependence of enzymatic degradation behavior was investigated for the polymorphic poly(3-hydroxypropionate) (P3HP), which has a basic backbone chemical structure of bacterial poly(3-hydroxyalkanoate)s (P3HAs). The P3HP films consisting of the beta-, gamma-, and/or delta-form crystal were cast or melt-crystallized as reported previously (Macromolecules 2005, 38, 6455; Macromolecules 2006, 39, 194-203) by controlling the molecular weight, crystallization temperature, and/or temperature of the melt. Their thermal properties, crystalline structures, morphologies, and (13)C solid spin-lattice relaxation dynamics were characterized by the differential scanning calorimetry, the wide-angle X-ray diffraction, the small-angle X-ray scattering (SAXS), and the (13)C solid-state NMR spectra (SNMR), respectively. Both the crystallinities and the lamellar thicknesses of P3HP films were found to decrease roughly in the order of beta-form > (or approximately) gamma-form > delta-form. From previous work, which indicates that the P3HA enzymatic degradation depends only on the degree of crystallinity and the lamellar thickness, their enzymatic degradation rates are then expected to increase in the order of beta-form < (or approximately) gamma-form < delta-form. Unexpectedly, their experimental P3HP enzymatic degradation rates in the presence of P3HA depolymerase isolated from Ralstonia pickettii T1 increase in the reverse order, i.e., delta-form < gamma-form < beta-form. The weight loss rate of the delta-form film is almost 1 order of magnitude smaller than that of the fastest degraded beta-form film. It is then strongly indicated that the crystalline structure plays a strikingly decisive role in the enzymatic degradation of P3HP. In particular, only when the conformation of crystalline chain accords with that of the bacterial poly(3-hydroxybutyrate) (P3HB) sample, i.e., the 2 1 helix conformation, is the P3HP sample degraded as slow as the P3HB sample. The inherent reason responsible for the unique P3HP enzymatic degradation behavior has been further clarified by comparing the molecular interaction and dynamics of polymorphic P3HP crystals.