Adsorption of metal complex dyes from aqueous solutions by pine sawdust

An attempt to alleviate the problem caused by the presence of metal complex dyes, mostly used in textile industries, in the textile effluents was undertaken. The effects of adsorbent particle size, pH, adsorbent dose, contact time and initial dye concentrations on the adsorption of metal complex dyes by pine sawdust was investigated. Acidic pH was favorable for the adsorption of metal complex dyes. A contact time of 120 min was required to reach the equilibrium. The experimental isotherm data were analyzed using the Langmuir, Freundlich and Temkin equations. The equilibrium data fit well the Langmuir isotherm. The monolayer adsorption capacities are 280.3 and 398.8 mg dye per g of pine sawdust for Metal Complex Blue and Metal Complex Yellow, respectively. The results indicate that pine sawdust could be employed as low-cost alternative to commercial activated carbon in aqueous solution for the removal of metal complex dyes.     

Dye removal from aqueous solution by adsorption on treated sawdust

Formaldehyde treated and sulphuric acid treated saw dusts were used to adsorb malachite green at varying dye concentration, adsorbent dose, pH and agitation time. Similar experiments were conducted with laboratory grade activated carbon to compare the results. The adsorption efficiency of sulphuric acid treated sawdust (SD) was higher than formaldehyde treated SD. The adsorption followed first order rate expression and Lagergren equation. An initial pH in the range of 6-9 was favorable for the dye removal by both the adsorbents. Dilute solutions were effectively decolorized by the adsorbents. It is proposed that in batch or stirred tank reactors, both adsorbents can be an attractive option for dye adsorption.     

Modeling, simulation, and experimental validation for continuous Cr(VI) removal from aqueous solutions using sawdust as an adsorbent

Continuous adsorption experiments were performed in a fixed-bed adsorption column to evaluate the performance of low-cost adsorbent (sawdust) developed for the removal of Cr(VI) from aqueous solutions. The effects of influencing parameters such as flow rate, mass of adsorbent, initial Cr(VI) concentration were studied and the corresponding breakthrough curves were obtained. The fixed-bed adsorption process parameters such as breakthrough time, total percentage removal of Cr(VI), adsorption exhaustion rate and fraction of unused bed-length were obtained. A mathematical model for fixed-bed adsorption column was proposed by incorporating the effect of velocity variation along the bed-length in the existing model. Pore and solid diffusion models were used to describe the intra-particle mechanism for Cr(VI) adsorption. The proposed mathematical model was validated with the literature data and the experimental data obtained in the present study and the model was found to be good for explaining the behavior of breakthrough curves.     

Microwave treated Salvadora oleoides as an eco-friendly biosorbent for the removal of toxic methyl violet dye from aqueous solution—A green approach

In the present study, microwave treated Salvadora oleoides (MW-SO) has been investigated as a potential biosorbent for the removal of toxic methyl violet dye. A batch adsorption method was experimented for biosorptive removal of toxic methyl violet dye from the aqueous solution. The effect of various operating variables, viz., adsorbent dosage, pH, contact time and temperature on the removal of the dye was studied and it was found that nearly 99% removal of the dye was possible under optimum conditions. Kinetic study revealed that a pseudo-second-order mechanism was predominant and the overall process of the dye adsorption involved more than one step. Hence, in order to investigate the rate determining step, intra-particle diffusion model was applied. Adsorption equilibrium study was made by analyzing Langmuir, Freundlich, and Dubinin–Radushkevich (D–R) adsorption isotherm models and the biosorption data was found to be best represented by the Langmuir model. The biosorption efficiency of MW-SO was also compared with unmodified material, Salvadora oleoides (SO). It was found that the sorption capacity (q_max) increased from 58.5 mg/g to 219.7 mg/g on MW treatment. Determination of thermodynamic parameters such as free energy change (ΔG°), enthalpy change (ΔH°) and entropy change (ΔS°) confirmed the spontaneous, endothermic and feasible nature of the adsorption process. The preparation of MW-SO did not require any additional chemical treatment and a high percentage removal of methyl violet dye was obtained in much lesser time. Thus, it is in agreement with the principles of green chemistry. The results of the present research work suggest that MW-SO can be used as an environmentally friendly and economical alternative biosorbent for the removal of methyl violet dye from aqueous solutions.     

Use of jute processing wastes for treatment of wastewater contaminated with dye and other organics

A study was conducted to examine the potential of jute processing waste (JPW) for the treatment of wastewater contaminated with dye and other organics generated from various activities associated with jute cultivation and fibre production. Adsorption studies in batch mode have been conducted using dye solution as an adsorbate and JPW as an adsorbent. A comparative adsorption study was made with standard adsorbents such as powdered and granular activated carbon (PAC and GAC, respectively). A maximum removal of 81.7% was obtained with methylene blue dye using JPW as compared to 61% using PAC and 40% using GAC under similar conditions. The adsorption potential of JPW was observed to be dependent on various parameters such as type of dye, initial dye concentration, pH and dosage of adsorbent. The batch sorption data conformed well to the Langmuir and Freundlich isotherms. However, lower BOD (33.3%) and COD (13.8%) removal from retting effluent was observed using JPW as compared to 75.6% BOD removal and 71.1% COD removal obtained with GAC.     

Adsorption of methylene blue dye from aqueous solution by sugar extracted spent rice biomass

This study was aimed at using sugar extracted spent rice biomass (SRB) as a potential adsorbent to remove methylene blue (MB) dye from aqueous solution. The SRB was used without any modification. A three factor full factorial experimental design (2(3)) was employed to investigate the effect of factors (adsorbent dose, dye concentration, temperature) and their interaction on the adsorption capacity and color removal. Two levels for each factor were used; adsorbent dose (0.25-0.5g/100mL), dye concentration (25-50mg/L), and temperature (25-45°C). Initial dye concentration and adsorbent dosage were found as significant factors for the adsorption of MB dye. Langmuir isotherm (R(2)>0.998) best explained the equilibrium of MB adsorption on SRB with monolayer adsorption capacity of 8.13mg/g. The pseudo-second order model (R(2)>0.999) was best fitted to explain the adsorption kinetics. Thermodynamic investigation revealed that the adsorption process was spontaneous, endothermic, and was feasible to treat dyeing wastewater.     

Bioremediation potential of a widespread industrial biowaste as renewable and sustainable biosorbent for synthetic dye pollution

In this study, a model synthetic azo dye (Basic red 46) bioremoval by Carpinus betulus sawdust as inexpensive, eco-friendly, and sustainable biosorbent from aqueous solution was examined in a batch biosorption system. The effective environmental parameters on the biosorption process, such as the value of pH, amount of biosorbent, initial dye concentration and contact time were optimized using classical test design. The possible dye-biosorbent interaction was determined by Fourier Transform Infrared Spectroscopy (FTIR) and Scanning Electron Microscopy (SEM). The equilibrium, thermodynamic, and kinetic studies for the biosorption of Basic red 46 onto the sawdust biomass were performed. In addition, a single-stage batch dye biosorption system was also designed. The dye biosorption yield of biosorbent was significantly influenced by the change of operating variables. The experimental data were best described by the Freundlich isotherm model and both the pseudo-first-order kinetic and the pseudo-second-order kinetic models. Thermodynamic research indicated that the biosorption of dye was feasible and spontaneous. Based on the Langmuir isotherm model, the biosorbent was found to have a maximum biosorption potential higher than many other biosorbents in the literature (264.915?mg g^?1). Thus, this investigation presents a novel green option for the assessment of waste sawdust biomass as a cheap and effective biosorbent material.     

Equilibrium and a two-stage batch adsorber design for reactive or disperse dye removal to minimize adsorbent amount

The adsorption of a reactive dye (Reactive Yellow K-4G) and a disperse dye (Disperse yellow brown S-2RFL) onto polyepicholorohydrin-dimethylamine (EPIDMA) cationic polymer modified bentonite (EPIDMA-bentonite) in batch adsorber was studied, respectively. Two equilibrium models, the Langmuir and Freundlich models were selected to follow the adsorption process. It was shown that the equilibrium experimental data for reactive dye adsorption could be well described by the Freundlich model, but for disperse dye the Langmuir model could be better. Based on the well correlated adsorption isotherm, an adsorption process design model was developed for the design of a two-stage batch adsorber to predict the minimum amount of adsorbent to achieve a specified percentage of dye removal at a given volume of wastewater effluents. The adsorption process design analysis indicated that compared with the single-stage batch adsorption, the two-stage process could significantly save adsorbent to meet the higher demands of dye removal efficiency.     

Effectiveness of Rice Agricultural Waste,Microbes and Wetland Plants in the Removal of Reactive Black-5 Azo Dye in Microcosm Constructed Wetlands

Azo dyes are commonly generated as effluent pollutants by dye using industries, causing contamination of surface and ground water. Various strategies are employed to treat such wastewater; however, a multi-faceted treatment strategy could be more effective for complete removal of azo dyes from industrial effluent than any single treatment. In the present study, rice husk material was used as a substratum in two constructed wetlands (CWs) and augmented with microorganisms in the presence of wetland plants to effectively treat dye-polluted water. To evaluate the efficiency of each process the study was divided into three levels, i.e., adsorption of dye onto the substratum, phytoremediation within the CW and then bioremediation along with the previous two processes in the augmented CW. The adsorption process was helpful in removing 50% dye in presence of rice husk while 80% in presence of rice husk biocahr. Augmentation of microorganisms in CW systems has improved dye removal efficiency to 90%. Similarly presence of microorganisms enhanced removal of total nitrogen (68% 0 and Total phosphorus (75%). A significant improvement in plant growth was also observed by measuring plant height, number of leaves and leave area. These findings suggest the use of agricultural waste as part of a CW substratum can provide enhanced removal of textile dyes.     

Adsorption of methylene blue using green pea peels (Pisum sativum): A cost-effective option for dye-based wastewater treatment

Methylene blue (MB), a common toxic dye, is largely discharged from dyeing processes for acrylic, nylon, silk, and woolen fabrics in textile industries. While application of conventional removal processes like chemical precipitation, ion exchange, commercial activated carbon adsorption, etc often become cost-prohibitive, the adsorption of MB by abundantly available green pea peel (GPP: Pisum sativum) derived and acid-treated carbon (GPP-AC) has proved to be a cost-attractive option in the present study. The physicochemical and morphological characteristics of GPP-AC were examined with the help of XRD, BET surface area, SEM, and Fourier transform infrared spectrophotometry ((FT-IR) analysis. The influences of such adsorption parameters as initial dye concentration, pH, contact time, adsorbent dosage, agitation speed, particle size, and temperature were evaluated and optimized. The equilibrium contact time for maximum adsorption of MB on to GPPAC was found to be 7 h. The equilibrium data of the adsorption process were modeled by using the Langmuir, Freundlich, Temkin, and Dubinin-Raduskevich (D-R) isotherms. However, the adsorption equilibrium data were best described by the Langmuir Isotherm model, with a maximum adsorption capacity of 163.94 mg MB/g GPPAC at 30°C.     

Adsorption of Methylene Blue Dye on Pure and Carbonized Water Weeds

The influence of process variables in batch adsorption has been used to assess the removal of methylene blue dye from aqueous solution using pure and carbonized biomasses of water hyacinth and water spinach. Dried leaves of the water weeds were carbonized at temperature up to 750°C. The optimum removal of dye was achieved at pH 10, 30°C, and 55 min at a dye concentration of 10 mg/L. In an attempt to describe the adsorption process, the equilibrium isotherm for each adsorbent was determined using Langmuir and Freundlich adsorption isotherm models. Maximum adsorption capacities based on the Langmuir model for pure and carbonized water hyacinth were (mg/g) 7.05 and 2.07, respectively, whereas those of pure and carbonized water spinach were 1.25 and 5.32, respectively. It was observed that the equilibrium data were well fit by both the Freundlich and Langmuir isotherms as R ² > .97. This study demonstrates that the two waterweeds are effective, environmentally friendly, and inexpensive biomaterials for the removal of color from industrial effluents.     

Scavenging Rhodamine B dye using moringa oleifera seed pod

Moringa oliferia seed pod was modified using orthophosphoric acid (H₃PO₄) and used as adsorbent for sequestering Rhodamine B (Rh-B) dye from aqueous solution. The acid-modified adsorbent (MOSPAC) was characterized using Scanning Electron microscopy (SEM), Fourier Transform Infra Red (FTIR), Energy Dispersive X-ray (EDX), pH point of zero charge (pH_pzc) and Boehm Titration (BT) techniques, respectively. Operational parameters such as contact time, initial dye concentration, adsorbent dosage, pH and solution temperature were studied in batch process. Optimum dye adsorption was observed at pH 3.01. Equilibrium adsorption data was tested data using four different isotherm models: Langmuir, Freundlich, Temkin and Dubinin-Radushkevich. Langmuir isotherm model fitted most with maximum monolayer adsorption capacity of 1250 mg g^–1. Pseudo-second-order kinetic model provided the best correlation for the experimental data. Thermodynamic study showed that the process is endothermic, spontaneous and feasible. MOSPAC is an effective adsorbent for the removal of RhB dye from aqueous solutions.     

Cationized starch-based material as a new ion-exchanger adsorbent for the removal of C.I. Acid Blue 25 from aqueous solutions

This article describes the use of a cationized starch-based material as new ion-exchanger adsorbent for the removal of C.I. Acid Blue 25 (AB 25) from aqueous solutions. Batch adsorption studies concerning the effects of contact time, pH and temperature are presented and discussed. Adsorption experimental data showed that: (i) the process was uniform and rapid: adsorption of dye reached equilibrium in 50 min in the wide pH range of dye solutions; (ii) adsorption kinetics followed the pseudo-second order model; (iii) the Langmuir model yielded a much better fit than the Freundlich model for the dye concentration range under study; (iv) this adsorbent exhibited interesting adsorption capacities: on the basis of the Langmuir analysis, the maximum adsorption capacity was determined to be 322 mg of dye per gram of material at 25 degrees C; (v) the adsorption capacity decreased with increasing temperature; and (vi) the negative value of free energy change indicated the spontaneous nature of adsorption.     

A breakthrough column study for removal of malachite green using coco-peat

Abstract

A continuous adsorption study in a fixed bed column using coco-peat (CP) as an adsorbent was carried out for the removal of toxic malachite green (MG) from contaminated water. Fixed bed column studies were carried out to check field application viability. Various parameters like particle size, pH, concentration, dose and interference were exercised to optimize dye removal. Data obtained from breakthrough column studies were evaluated using Thomas and BDST model. Thomas rate constants K_t (0.22?ml min^?1 mg^?1) and adsorption capacity q_o (181.04?mg g^?1) were estimated and found to favor efficiency of CP. Thomas model was tested with several parameters like flow rate, concentration, and bed depth. Upon increase in input dye concentration, flow rate and bed height, adsorption coefficients increased. According to BDST model, maximum dye uptake of 468.26?mg/l was obtained with an input dye concentration of 5?mg/l. HYBRID and MPSD error functions were tested and found that Thomas model fits best. Dilute hydrochloric acid was found best for desorption. Real wastewater from textile industry was analyzed and confirmed the prospect of large-scale industrial application. In conclusion, coco-peat can be used as a promising bio-sorbent in column bed for scavenging of MG from contaminated water.     

Biosorption and Reuse Potential of a Blue Green Alga for the Removal of Hazardous Reactive Dyes from Aqueous Solutions

The adsorption potential of a nonliving alga Nostoc comminutum for the removal of hazardous dyes from aqueous solutions was assessed. The algal biomass in its native form exhibited the highest dye removal efficiency at a pH of 1 and at a contact time of 50 min. The effect of various chemical pretreatments was studied in order to assess the role of surface chemistry and the underlying mechanism. Combined with Fourier transform infrared (FTIR) studies, it was concluded that the carboxylic and amine groups played a dominant role in the dye binding process. pH studies further revealed that besides the electrostatic mechanism, other physical interactions might be operative, which is also revealed from the Dubinin-Radushkevich (D-R) isotherm model. Kinetic studies indicated that the adsorption process followed the second-order kinetics and particle diffusion mechanisms were operative. Thermodynamic studies revealed that the adsorption of two dyes onto the algal biomass was feasible, spontaneous, and exothermic under the studied conditions. Microwave irradiation was proposed as a green method for the regeneration and reuse of the biomass. A 16% loss in the regeneration efficiency of the biosorbent was observed, which reveals its stability and reuse potential. Column experiments with real textile wastewater established the practicality of the developed system. Finally, a comparative study revealed the efficacy of the biosorbent with other previously reported biosorbents for dye removal.     

The removal of chromium(VI) from aqueous solutions by Fagus orientalis L

The removal of chromium(VI) from aqueous solution under different conditions using an adsorbent was investigated. This adsorbent is Beech (Fagus orientalis L.) sawdust studied by using batch techniques. Batch studies indicated that the percent adsorption decreased with increasing initial concentration of chromium(VI). A contact time of 80 min was found to be optimum. Maximum chromium(VI) removal was observed near a pH of 1.0. Adsorption conformed to the Freundlich and Langmuir isotherms.     

Adsorption of chromium from aqueous solution on treated sawdust

The adsorption of Cr(VI) from aqueous solutions on formaldehyde treated sawdust (SD) and sulphuric acid treated sawdust carbon (SDC) of Indian Rosewood, a timber industry waste, was studied at varying Cr(VI) concentrations, adsorbent dose, pH and agitation time. Similar experiments were conducted with commercially available coconut based activated carbon to compare the results. The Cr(VI) adsorption efficiency on SDC was higher than SD. The adsorption followed first order rate expression and Lagergren equation. An initial pH of 3.0 was most favorable for Cr(VI) removal by both the adsorbents. Maximum Cr(VI) was sequestered from the solution within 60 min after the beginning for every experiment. It is proposed that SDC and SD can be potential adsorbents for Cr(VI) removal from dilute solutions.     

Use of low-cost biological wastes and vermiculite for removal of chromium from tannery effluent

Biological wastes (sawdust, rice husk, coirpith and charcoal) and a naturally occurring mineral (vermiculite) have been tested for their effectiveness in removing Cr from tannery effluent through batch and column experiments. The adsorption capacities of the substrates were also evaluated using isotherm tests and computing distribution co-efficient. The sawdust exhibited a higher adsorption capacity (k = 1482 mgkg(-1)), followed by coirpith (k = 159 mgkg(-1)). The biosorbent and mineral vermiculite in columns were found very effective in removing Cr from tannery effluent. About 94% removal of Cr was achieved by a column of coirpith, and equally (93%) by a column containing a mixture of coirpith and vermiculite. This study showed that biological wastes are potential adsorbents of Cr, which could be successfully used to reduce the Cr concentrations in tannery effluent.     

Experimental and kinetic studies on methylene blue adsorption by coir pith carbon

Varying the parameters such as agitation time, dye concentration, adsorbent dose, pH and temperature carried out the potential feasibility of thermally activated coir pith carbon prepared from coconut husk for removal of methylene blue. Greater percentage of dye was removed with decrease in the initial concentration of dye and increase in amount of adsorbent used. Kinetic study showed that the adsorption of dye on coir pith carbon was a gradual process. Lagergren first-order, second-order, intra particle diffusion model and Bangham were used to fit the experimental data. Equilibrium isotherms were analysed by Langmuir, Freundlich, Dubnin-Radushkevich, and Tempkin isotherm. The adsorption capacity was found to be 5.87 mg/g by Langmuir isotherm for the particle size 250-500 microm. The equilibrium time was found to be 30 and 60 min for 10 and 20 mg/L and 100 min for 30, 40 mg/L dye concentrations, respectively. A maximum removal of 97% was obtained at natural pH 6.9 for an adsorbent dose of 100 mg/50 mL and 100% removal was obtained for an adsorbent dose of 600 mg/50 mL of 10 mg/L dye concentration. The pH effect and desorption studies suggest that chemisorption might be the major mode of the adsorption process. The change in entropy (DeltaS0) and heat of adsorption (DeltaH0) of coir pith carbon was estimated as 117.20 J/mol/K and 30.88 kJ/mol, respectively. The high negative value of change in Gibbs free energy indicates the feasible and spontaneous adsorption of methylene blue on coir pith carbon.     

Biosorption of Food Green 3 by a novel green generation composite biosorbent from aqueous environment

A green type composite biosorbent composed of pine, oak, hornbeam, and fir sawdust biomasses modified with cetyltrimethylammonium bromide (CTAB) was first used for biosorption of an unsafe synthetic food dye, Food Green 3 from liquid medium in this study. Batch studies were carried by observing the effects of pH, dye concentration, biosorbent amount, and contact time. The equilibrium data were analyzed using Freundlich, Langmuir, and Dubinin–Radushkevich equations. Freundlich model gave a better conformity than other equations. The maximum dye removal potential of biosorbent was found to be 36.6 mg/g based on Langmuir isotherm. The pseudo-first-order, pseudo-second-order, Elovich, and intra-particle diffusion models were applied to clarify the process kinetics of biosorption. The mechanism studies suggested the biosorption process obeying Elovich kinetics and involving pore diffusion. The estimated values of biosorption free energy from Dubinin–Radushkevich isotherm (E value <8 kJ/mol) and thermodynamic studies (0 < ΔG° < ?20 kJ/mol) implied a spontaneous, feasible, and physical process. Hence, this investigation suggested that the CTAB modified mix sawdust biomass could be a promising biosorbent for biosorption of such problematic dyes from impacted media.