Two‐channel near‐infrared fluorescence Ag+ ion sensing of a new star‐shaped dendrimer

A new near‐infrared fluorescence sensor PDI‐PD for Ag⁺ ions was successfully prepared and its structure characterized by ¹H nuclear magnetic resonance (NMR), ¹³C NMR and high‐resolution mass spectrometry; matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry (HRMS MALDI‐TOF). The probe exhibited rapid, sensitive, and selective two‐channel fluorescence responses towards Ag⁺ ions and protons. The probe has a marked high binding affinity and high sensitivity for Ag⁺, with a detection limit of 1.4 × 10^?6 M. An approximately five‐fold enhanced core emission at 784 nm was attributed to fluorescence resonance energy transfer (FRET). The enhanced core emission of the probe with Ag⁺ ions based on photo‐induced electron transfer and FRET is discussed. In addition, the probe presented a visible colour change. All experimental results demonstrated that PDI‐PD is an efficient tool for the selective, sensitive and rapid detection of Ag⁺ ions and protons using two‐channel fluorescence responses.     

Determination of oxytetracycline hydrochloride in milk and egg white samples using Ru(bipy)32+–Ce(SO4)2 chemiluminescence

A novel, rapid and sensitive chemiluminescence (CL) method for the determination of oxytetracycline hydrochloride (OTCH) is described in this paper. The presented method was based on the fact that OTCH could immensely enhance the CL of the reaction of cerium sulfate and tris(2,2‐bipyridyl) ruthenium (II) in acidic medium. Under optimal experimental conditions, CL intensity was favorably linear for OTCH in the range 5.0 × 10^?7 to 5.0 × 10^?5 g/ml, with a detection limit of 1.5 × 10^?7 g/ml (S/N = 3). The relative standard detection was 4.76% for 5.0 × 10^?6 g/ml (n = 11). This method was successfully applied to the analysis of OTCH in milk and egg white samples. According to the results of the kinetic curves for OTCH in the Ru(bipy)₃²⁺–Ce(SO₄)₂ CL system, together with CL and ultraviolet (UV)–visible spectra, the possible mechanism of the CL reaction is discussed briefly.     

The behaviors of metal ions in the CdTe quantum dots–H2O2 chemiluminescence reaction and its sensing application

The behaviors of 15 kinds of metal ions in the thiol‐capped CdTe quantum dots (QDs)–H₂O₂ chemiluminescence (CL) reaction were investigated in detail. The results showed that Ag⁺, Cu²⁺ and Hg²⁺ could inhibit CdTe QDs and H₂O₂ CL reaction. A novel CL method for the selective determination of Ag⁺, Cu²⁺ and Hg²⁺ was developed, based on their inhibition of the reaction of CdTe QDs and H₂O₂. Under the optimal conditions, good linear relationships were realized between the CL intensity and the logarithm of concentrations of Ag⁺, Cu²⁺ and Hg²⁺. The linear ranges were from 2.0 × 10^?6 to 5.0 × 10^?8 mol L^?1 for Ag⁺, from 5.0 × 10^?6 to 7.0 × 10^?8 mol L^?1 for Cu²⁺ and from 2.0 × 10^?5 to 1.0 × 10^?7 mol L^?1 for Hg²⁺, respectively. The limits of detection (S/N = 3) were 3.0 × 10^?8, 4.0 × 10^?8 and 6.7 × 10^?8 mol L^?1 for Ag⁺, Cu²⁺ and Hg²⁺, respectively. A possible mechanism for the inhibition of CdTe QDs and H₂O₂ CL reaction was also discussed. Copyright © 2009 John Wiley & Sons, Ltd.     

A highly efficient and selective turn‐on fluorescent sensor for Hg2+, Ag+ and Ag nanoparticles based on a coumarin dithioate derivative

Based on chelation‐enhanced fluorescence, a new fluorescent coumarin derivative probe 3(1‐(7‐hydroxy‐4‐methylcoumarin)ethylidene)hydrazinecarbodithioate for Hg²⁺, Ag⁺ and Ag nanoparticles is reported. Fluorescent probe acts as a rapid and highly selective “off–on” fluorescent probe and fluorescence enhancement by factors 5 to12 times was observed upon selective complexation with Hg²⁺, Ag⁺ and Ag nanoparticles. The molar ratio plots indicated the formation of 1:1 complexes between Hg²⁺ and Ag⁺ with the probe. The linear response range covers a concentration range 0.1 × 10^–5–1.9 × 10^–5 mol/L, 0.1 × 10^–5–2.3 × 10^–5 mol/L and 0.146 × 10^–12–2.63 × 10^–12 mol/L for Hg²⁺, Ag⁺ and Ag nanoparticles, respectively. The interference effect of some anions and cations was also tested. Copyright © 2013 John Wiley & Sons, Ltd.     

Enhanced electrochemiluminescence from reduced graphene oxide–CdTe quantum dots for highly selective determination of copper ion

An electrochemiluminescence (ECL) sensor based on reduced graphene oxide–CdTe quantum dots (RGO–CdTe QDs) composites for detecting copper ion (Cu²⁺) was proposed. The ECL behaviours of the RGO–CdTe QD modified electrode were investigated with H₂O₂ as the co‐reactant. Quantitative detection of Cu²⁺ was realized as Cu²⁺ could effectively quench the ECL signal of the RGO–CdTe QDs. A wide linear range of 1.00 × 10^?14 to 1.00 × 10^?4 M (R = 0.9953) was obtained under optimized conditions, and a detection limit (S/N = 3) was achieved of as low as 3.33 × 10^?15 M. The proposed sensor also exhibited good stability and selectivity for the detection of copper ions. Finally, the analytical application of the proposed sensor was also evaluated using river water.     

Highly sensitive spectrofluorimetric determination of trace amounts of prulifloxacin using the aluminium(III)–prulifloxacin system

The fluorescence of the prulifloxacin (PUFX)–Al(III) system was investigated . Experiments indicated that the fluorescence intensity of prulifloxacin could be greatly enhanced by Al(III) and sensitized by sodium dodecylbenzene sulphonate (SDBS). Accordingly, a sensitive spectrofluorimetric method for the determination of prulifloxacin was established. While excited at 275 nm, the enhanced fluorescence intensity at 412 nm of the system (ΔF) showed a good linear relationship with the concentration of prulifloxacin within the range 4.0 × 10^–8–3.0 × 10^–6 mol/L. The regression equation was ΔF = 9.83 + 10.8 × 10⁷c (mol/L); the correlation coefficient and detection limit (3σ/k) were 0.99901 and 2.0 × 10^–8 mol/L, respectively. The proposed method has been successfully applied to determine prulifloxacin in real pharmaceutical samples. The luminescence mechanism of the system is also discussed in detail. Copyright © 2008 John Wiley & Sons, Ltd.     

Flow‐injection determination of cysteine in pharmaceuticals based on luminol–persulphate chemiluminescence detection

A flow injection (FI) method is reported for the determination of l‐ cysteine, based on its enhancement on chemiluminescence (CL) emission of luminol oxidized by sodium persulphate in alkaline solution. The calibration graph was linear over the range 1.0 × 10^–9–5.0 × 10^–7 mol/L (r² = 0.9992), with relative standard deviations (RSDs) in the range 1.1–2.3% (n = 4). The limit of detection (3σ blank) was 5.0 × 10^–10 mol/L with a sample throughput of 120/h. The method was applied to pharmaceuticals and the results obtained were in reasonable agreement with the amount labelled. The proposed method was also applied to cysteine in synthetic amino acid mixtures. Calibration graphs of N‐acetylcysteine and glutathione over the range 1.0–50 × 10^–8 and 0.5–7.5 × 10^–7 mol/L were also established (r² = 0.998 and 0.9986) with RSDs in the range 1.0–2.0% (n = 4), and the limits of detection (3σ blank) were 5.0 × 10^–9 and 1.0 × 10^–8 mol/L, respectively. Copyright © 2008 John Wiley & Sons, Ltd.     

A simple Chalcone‐based ratiometric chemosensor for silver ion

Herein, we report the selective binding of Ag⁺ ion by the anthracene‐based chalcone receptor 1. Receptor 1 behaves as a selective and sensitive chemosensor for the recognition of Ag⁺ over other heavy and transition metal ions without any interference and is capable of detecting the metal ion down to 0.15 × 10^?6 M. Receptor 1 on binding with Ag⁺ ions exhibits a ratiometric fluorescence enhancement, which is due to the inhibition of photoinduced electron transfer along with the intramolecular charge transfer mechanism. Copyright © 2015 John Wiley & Sons, Ltd.     

Determination of puerarin by capillary electrophoresis with chemiluminescence detection

A new analytical method for puerarin using capillary electrophoretic (CE) separation and chemiluminescence (CL) detection has been developed. The detection was based on the enhanced CL intensity of the reaction between luminol and potassium ferricyanide by puerarin in alkaline solution. A laboratory-built CE–CL apparatus was deployed for the puerarin detection. Under the optimal conditions, a linear range from 5.0 × 10^?8 to 2.5 × 10^?6 M and a detection limit of 1.0 × 10^?8 M (S/N = 3) for puerarin were achieved. The determination of puerarin was achieved in less than 5 min, and the proposed method was applied to the determination of puerarin in pharmaceutical, human urine and human plasma samples.     

Selective sensing Ca2+ with a spiropyran‐based fluorometric probe

Spiropyran (SP) and its derivatives operate between their ring opening and closing forms as a versatile molecular platform for the fluorescence detection of cations and anions, using a colour change for signalling. A functionalized SP fluorescence probe, L , was prepared and characterized. Probe L can detect Ca²⁺ with a fluorescence ‘turn‐on’ response in ethanol solution. It selectively binds Ca²⁺ to form a 1:1 ligand/metal complex, which produced a new emission band centred at 604 nm. The sensing result was clearly observed by the solution colour change from colourless to pink under visible light, and from blue to red under ultraviolet light. The detection limit was calculated to be 4.53 × 10^?8 M for Ca²⁺. The probe provides another possibility that SP‐based derivatives could be used for the development and detection of metal ions in environmental and physiological systems.     

Determination of pioglitazone hydrochloride by flow injection chemiluminescence tris(2,2′-bipyridyl)ruthenium(II)–silver(III) complex system

A novel flow injection-chemiluminescence (FI–CL) approach is proposed for the assay of pioglitazone hydrochloride (PG-HCl) based on its enhancing influence on the tris(2,2′-bipyridyl)ruthenium(II)–silver(III) complex (Ru(bipy)₃²⁺-DPA) CL system in sulfuric acid medium. The possible CL reaction mechanism is discussed with CL and ultraviolet (UV) spectra. The optimum experimental conditions were found as: Ru(bipy)₃²⁺, 5.0 × 10⁻⁵ M; sulfuric acid, 1.0 × 10⁻³ M; diperiodatoargentate(III) (DPA), 1.0 × 10⁻⁴ M; potassium hydroxide, 1.0 × 10⁻³ M; flow rate 4.0 ml min⁻¹ for each flow stream and sample loop volume, 180 μl. The CL intensity of PG-HCl was linear in the range of 1.0 × 10⁻³ to 5.0 mg L⁻¹ (R² = 0.9998, n = 10) with limit of detection [LOD, signal-to-noise ratio (S/N) = 3] of 2.2 × 10⁻⁴ mg L⁻¹, limit of quantification (LOQ, S/N = 10) of 6.7 × 10⁻⁴ mg L⁻¹, relative standard deviation (RSD) of 1.0 to 3.3% and sampling rate of 106 h⁻¹. The methodology was satisfactorily used to quantify PG-HCl in pharmaceutical tablets with recoveries ranging from 93.17 to 102.77 and RSD from 1.9 to 2.8%.     

Nitrogen‐doped carbon dots as a fluorescent probe for the highly sensitive detection of Ag+ and cell imaging

An easy hydrothermal synthesis strategy was applied to synthesize green‐yellow emitting nitrogen‐doped carbon dots (N‐CDs) using 1,2‐diaminobenzene as the carbon source, and dicyandiamide as the dopant. The nitrogen‐doped CDs resulted in improvement in the electronic characteristics and surface chemical activities. N‐CDs exhibited bright fluorescence emission and could response to Ag⁺ selectively and sensitively. Other ions produced nearly no interference. A N‐CDs based fluorescent probe was then applied to sensitively determine Ag⁺ with a detection limit of 5 × 10^?8 mol/L. The method was applied to the determination of Ag⁺ dissolved in water. Finally, negligibly cytotoxic, excellently biocompatibile, and highly fluorescent carbon dots were applied for HepG2 cell imaging and the quenched fluorescence by adding Ag⁺, which indicated its potential applications.     

A ratiometric fluorescence strategy based on copper nanoclusters/carbon dots for sensitive detection of doxorubicin

Sensitive detection of doxorubicin (DOX) is critical for clinical theranostics. A novel ratiometric fluorescence strategy based on the inner filter effect (IFE) has been established for the sensitive detection of DOX by designing a ratiometric fluorescence probe. In the presence of DOX, the fluorescence intensity of copper nanoclusters (CuNCs) at 485 nm decreases, and the fluorescence intensity of carbon dots at 560 nm increases. Therefore, DOX can be quantitatively detected by measuring the ratio of the fluorescence intensities at 560 and 485 nm (F₅₆₀/F₄₈₅). The F₅₆₀/F₄₈₅ ratio exhibits a linear correlation with the DOX concentration in the range from 1.0 × 10⁻⁸ M to 1.0 × 10⁻⁴ M with the detection limit of 3.7 nM. Furthermore, this method was also successfully applied to the analysis of DOX in human plasma samples, affording an effective platform for drug safety management.     

The fluorescence enhancement of quercetin–nucleic acid system and the analytical application

Nucleic acid can greatly enhance the fluorescence intensity of quercetin in HMTA‐HCl (pH 5.5) buffer. The enhanced intensity is in proportion to the concentration of nucleic acids in the range 5.0 × 10^?9 to 1.0 × 10^?6 g/mL for fsDNA, 5.0 × 10^?9 to 7.0 × 10^?7 g/mL for ctDNA and 5.0 × 10^?9 to 1.0 × 10^?6 g/mL for yRNA, and their detection limits (S/N = 3) are 3.5 × 10^?9, 7.8 × 10^?10 and 2.6 × 10^?9 g/mL, respectively. In comparison with most reported fluorescent probes for the determination of nucleic acids, the proposed probe has higher sensitivity and lower toxicity. The interaction investigation indicates that quercetin binds with double‐strand DNA in groove binding mode, resulting in fluorescence enhancement of this system. Copyright © 2009 John Wiley & Sons, Ltd.     

Kinetics of Potassium and Magnesium Uptake by Intact Soybean Roots

The kinetics of uptake of K⁺ and Mg²⁺ were studied by using intact soybean [Glycine max (L.) Merr. cv. Amsoy] roots. Uptake of K⁺ in the concentration range 1.29 × 10^?5 to 1.82 × 10^?3 M can be represented by two phases of a single, multiphasic mechanism. Similarly, uptake of Mg²⁺ in the concentration range 4.10 × 10^?6 to 2.49 × 10^?4M was biphasic.     

The effects of copper on photosynthesis and biomolecules yield in Chlorolobion braunii

Our knowledge of the effects of copper on microalgal physiology is largely based on studies conducted with high copper concentrations; much less is known when environmentally relevant copper levels come into question. Here, we evaluated the physiology of Chlorolobion braunii exposed to free copper ion concentrations between 5.7 × 10^?9 and 5.0 × 10^?6 mol · L^?1, thus including environmentally relevant values. Population growth and maximum photosynthetic quantum yield of PSII were determined daily during the 96 h laboratory controlled experiment. Exponentially‐growing cells (48 h) were analyzed for effective quantum yield and rapid light curves (RLC), and total lipids, proteins, carbohydrates, chlorophyll a and carotenoids were determined. The results showed that growth rates and population density decreased gradually as copper increased in experiment, but the photosynthetic parameters (maximum and effective quantum yields) and photochemical quenching (qP) decreased only at the highest free copper concentration tested (5.0 × 10^?6 mol · L^?1); nonphotochemical quenching (NPQ) increased gradually with copper increase. The RLC parameters Ek and rETRmax were inversely proportional to copper concentration, while α and Im decreased only at 5.0 × 10^?6 mol · L^?1. The effects of copper in biomolecules yield (mg · L^?1) varied depending on the biomolecule. Lipid yield increased at free copper concentration as low as 2.5 × 10^?8 mol · L^?1, but proteins and carbohydrates were constant throughout.     

Phenothiazine–rhodamine‐based colorimetric and fluorogenic ‘turn‐on' sensor for Zn2+ and bioimaging studies in live cells

A phenothiazine–rhodamine (PTRH) fluorescent dyad was synthesized and its ability to selectively sense Zn²⁺ ions in solution and in in vitro cell lines was tested using various techniques. When compared with other competing metal ions, the PTRH probe showed the high selectivity for Zn²⁺ ions that was supported by electronic and emission spectral analyses. The emission band at 528 nm for the PTRH probe indicated the ring closed form of PTRH, as for Zn²⁺ ion binding to PTRH, the λ_em get shift to 608 nm was accompanied by a pale yellow to pink colour (under visible light) and green to pinkish red fluorescence emission (under UV light) due to ring opening of the spirolactam moiety in the PTRH ligand. Spectral overlap of the donor emission band and the absorption band of the ring opened form of the acceptor moiety contributed towards the fluorescence resonance energy transfer ON mechanism for Zn²⁺ ion detection. The PTRH sensor had the lowest detection limit for Zn²⁺, found to be 2.89 × 10^?8 M. The sensor also demonstrated good sensing application with minimum toxicity for in vitro analyses using HeLa cells.     

Spectrofluorimetric determination of bilirubin in serum samples

A new spectrofluorimetric method was developed for determination of trace amount of bilirubin. Using oxytetracycline–Eu³⁺ as a fluorescent probe, in the buffer solution of pH = 7.3, bilirubin can reduce remarkably the fluorescence intensity of the oxytetracycline–Eu³⁺ complex at λ = 612 nm and the reduced fluorescence intensity was in proportion to the concentration of bilirubin. Optimum conditions for the determination of bilirubin were also investigated. The linear range and limit of detection for the determination of bilirubin were 5.0 × 10^?7, 3.0 × 10^?5 and 7.7 × 10^?8 mol L^?1, respectively. This method is simple, practical and relatively free of interference from coexisting substances and can be successfully applied to assess bilirubin in serum samples and compared with the modified Jendrassik–Grof method in clinical analysis. The quenching mechanism of the fluorescence intensity in the system is also discussed. Copyright © 2010 John Wiley & Sons, Ltd.     

Spectrofluorimetric determination of aluminum ions via complexation with luteolin in absolute ethanol

An optimized and validated spectrofluorimetric method has been developed for the rapid determination of aluminum in absolute ethanol. The method is based on the chelation of aluminum and luteolin which results in a complex exhibiting an intense emission signal. The characterization of Al–luteolin complex was studied using ultraviolet–visible spectrometry, infrared spectrometry, fluorescence and mass spectrometry. The complex stoichiometry ratio of aluminum:luteolin was 1:2. The fluorescence of the complex was monitored at an emission wavelength of 545 nm with excitation at 518 nm. The linear concentration range was 6.5 × 10^‐7 to 4.0 × 10^‐5 M with a correlation coefficient of r = 0.998. The detection limit was 5.0 × 10^‐7 M. The method was appropriately validated and yielded relative standard deviations of < 2.3% (n = 5), which was considered acceptable. The method was successfully applied in the determination of aluminum in river water, skin care products and pharmaceutical samples. Copyright © 2013 John Wiley & Sons, Ltd.     

Determination of pholcodine in syrups and human plasma using the chemiluminescence system of tris(1,10 phenanthroline)ruthenium(II) and acidic Ce(IV)

Pholcodine is an opiate derivative drug which is widely used in pediatric medicine. In this study, a chemiluminescence (CL) method is described that determines pholcodine in human plasma and syrup samples. This method is based on the fact that pholcodine can greatly enhance the weak CL emission of reaction between tris(1,10 phenanthroline)ruthenium(II), Ru(phen)₃²⁺, and acidic Ce(IV). The CL mechanism is described in detail using UV–vis light, fluorescence and CL spectra. Effects of chemical variables were investigated and under optimum conditions, CL intensity was proportional to the pholcodine concentration over the range 4.0 × 10^?8 to 8.0 × 10^?6 mol  L^?1. The limit of detection (LOD) (S/N = 3) was 2.5 × 10^?8 mol  L^?1. Percent of relative standard deviations (%RSD) for 3.0 × 10^?7 and 3.0 × 10^?6 mol  L^?1 of pholcodine was 2.9 and 4.0%, respectively. Effects of common ingredients were investigated and the method was applied successfully to the determination of pholcodine in syrup samples and human plasma.